Soft lockup in e100 driver ?
Running very recent Fedora Core Development kernel I can following
soft-oops.. ( 2.6.12-1.1455_FC5smp )
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
BUG: soft lockup detected on CPU#0!
Pid: 10743, comm: ifconfig
EIP: 0060:[<f88bf2f9>] CPU: 0
EIP is at e100_clean_cbs+0x2f/0x12b [e100]
EFLAGS: 00000293 Not tainted (2.6.12-1.1455_FC5smp)
EAX: 495c7c2b EBX: 495c7c2b ECX: f6c311a0 EDX: 00000000
ESI: 00000040 EDI: f6c30000 EBP: f71a4b20 DS: 007b ES: 007b
CR0: 8005003b CR2: 0804a544 CR3: 01e9cd80 CR4: 000006f0
[<f88c0708>] e100_down+0x66/0x9a [e100] [<f88c1623>] e100_close+0xa/0xd [e100] [<c02b7adb>] dev_close+0x40/0x7e [<c02b8f59>] dev_change_flags+0x46/0xf5 [<c02f76b3>] devinet_ioctl+0x564/0x5df [<c02af22c>] sock_ioctl+0xc3/0x250 [<c02af169>] sock_ioctl+0x0/0x250 [<c01762ef>] do_ioctl+0x1f/0x6d [<c017648f>] vfs_ioctl+0x50/0x1c6 [<c0176662>] sys_ioctl+0x5d/0x6f [<c010394d>] syscall_call+0x7/0xb [<c014473f>] softlockup_tick+0x6f/0x80 [<c01085b8>] timer_interrupt+0x2d/0x75 [<c01448dd>] handle_IRQ_event+0x2e/0x5a [<c01449cb>] __do_IRQ+0xc2/0x127 [<c0105f7e>] do_IRQ+0x4e/0x86 ======================= [<c01160cc>] smp_apic_timer_interrupt+0xc1/0xca [<c0104382>] common_interrupt+0x1a/0x20 [<f88bf2f9>] e100_clean_cbs+0x2f/0x12b [e100] [<f88c0708>] e100_down+0x66/0x9a [e100] [<f88c1623>] e100_close+0xa/0xd [e100] [<c02b7adb>] dev_close+0x40/0x7e [<c02b8f59>] dev_change_flags+0x46/0xf5 [<c02f76b3>] devinet_ioctl+0x564/0x5df [<c02af22c>] sock_ioctl+0xc3/0x250 [<c02af169>] sock_ioctl+0x0/0x250 [<c01762ef>] do_ioctl+0x1f/0x6d [<c017648f>] vfs_ioctl+0x50/0x1c6 [<c0176662>] sys_ioctl+0x5d/0x6f [<c010394d>] syscall_call+0x7/0xb
Preconditions for this are:
- E100 card stopped working for some reason (no idea why, it just does sometimes at this oldish 2x P-III machine)
- There are active datastreams running in and out (around 0.2 Mbps out, multiple megabits in.)
- Commanding then "ifconfig eth0 down" results in what feels like system freezing, but it does recover in about 30-60 seconds (it takes long enough for me to sweat bullets...)
- While in freeze state, keyboard can go crazy, but mouse does respond, as well as tvtime shows bt848 captured live video.
Quoted 3 lines · Matti Aarnio
Running very recent Fedora Core Development kernel I can following
soft-oops.. ( 2.6.12-1.1455_FC5smp )
Various patches to the e100 driver have been merged since 2.6.12.1 (which is ~1.5months old), so it would make sense to try a more recent kernel like 2.6.13-rc6, 2.6.13-rc6-git1 or 2.6.13-rc5-mm1 and see if you can still reproduce the problem with those.
Signature · 3 lines
Jesper Juhl <[email protected]> Don't top-post http://www.catb.org/~esr/jargon/html/T/top-post.html Plain text mails only, please http://www.expita.com/nomime.html
Quoted 8 lines · Jesper Juhl
Quoted 3 lines · Matti Aarnio
Running very recent Fedora Core Development kernel I can following
soft-oops.. ( 2.6.12-1.1455_FC5smp )Various patches to the e100 driver have been merged since 2.6.12.1 (which is ~1.5months old), so it would make sense to try a more recent kernel like 2.6.13-rc6, 2.6.13-rc6-git1 or 2.6.13-rc5-mm1 and see if you can still reproduce the problem with those.
The kernel in question is less than 3 days old RedHat Fedora Core Development kernel with baseline as:
* Sun Aug 07 2005 Dave Jones <[email protected]>
- 2.6.13-rc5-git4
Those merges have not helped.
Quoted 2 lines
Signature · 1 line
Jesper Juhl <[email protected]>
/Matti Aarnio
Quoted 10 lines · Matti Aarnio
Quoted 8 lines · Jesper Juhl
Quoted 3 lines · Matti Aarnio
Running very recent Fedora Core Development kernel I can following
soft-oops.. ( 2.6.12-1.1455_FC5smp )Various patches to the e100 driver have been merged since 2.6.12.1 (which is ~1.5months old), so it would make sense to try a more recent kernel like 2.6.13-rc6, 2.6.13-rc6-git1 or 2.6.13-rc5-mm1 and see if you can still reproduce the problem with those.
Quoted 6 lines
The kernel in question is less than 3 days old RedHat Fedora Core Development kernel with baseline as:
* Sun Aug 07 2005 Dave Jones <[email protected]>
- 2.6.13-rc5-git4Those merges have not helped.
Matti,
I believe Fedora must have added Ingo's soft lockup detect code. I've made additions to this code as well. Could you point me to a link that I could download this kernel source. No rpm's or packagemanagers please. Just a tarball would be fine.
Thanks,
-- Steve
Quoted 16 lines · Steven Rostedt
Quoted 15 lines · Matti Aarnio
Quoted 8 lines · Jesper Juhl
Quoted 3 lines · Matti Aarnio
Running very recent Fedora Core Development kernel I can following
soft-oops.. ( 2.6.12-1.1455_FC5smp )Various patches to the e100 driver have been merged since 2.6.12.1 (which is ~1.5months old), so it would make sense to try a more recent kernel like 2.6.13-rc6, 2.6.13-rc6-git1 or 2.6.13-rc5-mm1 and see if you can still reproduce the problem with those.
The kernel in question is less than 3 days old RedHat Fedora Core Development kernel with baseline as:
* Sun Aug 07 2005 Dave Jones <[email protected]>
- 2.6.13-rc5-git4
Quoted 8 lines
Quoted 1 line
Those merges have not helped.
Matti,
I believe Fedora must have added Ingo's soft lockup detect code. I've made additions to this code as well. Could you point me to a link that I could download this kernel source. No rpm's or packagemanagers please. Just a tarball would be fine.
The fundamental thing is, IT LOCKS UP (for a while), when I do "ifconfig eth0 down" and there is active traffic but the card DIES somehow. Apparently it requires marginal/unreliable hardware to happen as well. (Which for e100 is rather rare.)
That is: at first the card dies, then I notice it, and do the ifconfig. Then things go _bad_, and recover. Then I do 'rmmod e100', and restart network (which reloads the driver module), and things work once again.
Fedora kernel sources have this "softlockups" patch file: (size and date)
6159 May 12 04:50 linux-2.6.12-detect-softlockups.patch
That file I can upload, if you want. Or send in email. Rest of the RPM-wrapper CPIO package I would prefer not to...
Quoted 2 lines
Thanks,
-- Steve
/Matti Aarnio
Quoted 4 lines · Matti Aarnio
The fundamental thing is, IT LOCKS UP (for a while), when I do "ifconfig eth0 down" and there is active traffic but the card DIES somehow. Apparently it requires marginal/unreliable hardware to happen as well. (Which for e100 is rather rare.)
This does look like a problem with the e100. I have a SMP machine and another machine with a e100 card, but not the both together, and I'm not about to start pulling cards. Does this only happen in SMP or do you also see this problem running a UP kernel (you only need to run a UP kernel on SMP machine to get the same results)? I'm running debian but I guess I could run the Fedora kernel to see if I can get the same behavior.
Quoted 4 lines
That is: at first the card dies, then I notice it, and do the ifconfig. Then things go _bad_, and recover. Then I do 'rmmod e100', and restart network (which reloads the driver module), and things work once again.
So you have something locking up momentarily, then coming back to normal? After the rmmod of e100 and bringing back up the network, all is in order? Just confirming what you see.
Quoted 6 lines
Fedora kernel sources have this "softlockups" patch file: (size and date)
6159 May 12 04:50 linux-2.6.12-detect-softlockups.patchThat file I can upload, if you want. Or send in email. Rest of the RPM-wrapper CPIO package I would prefer not to...
Did you add that patch yourself, or did it come with an update? I was just fiddling with rpms and I can use them too, with the rpm2cpio, it works nice. So if you can just point to a link then I'll download it and try it out. I found
http://download.fedora.redhat.com/pub/fedora/linux/core/updates/testing/4/i386/kernel-smp-2.6.12-1.1411_FC4.i686.rpm
but this is to 1411 and not to what you showed (1455).
-- Steve
Quoted 6 lines · Matti Aarnio
Running very recent Fedora Core Development kernel I can following
soft-oops.. ( 2.6.12-1.1455_FC5smp )e100: eth0:
e100_watchdog: link up, 100Mbps, full-duplexBUG: soft lockup detected on CPU#0!
Could this be a false positive? It's suspicious that the soft lockup detector was just merged to mainline then you got this.
Lee
Quoted 10 lines · Lee Revell
Quoted 6 lines · Matti Aarnio
Running very recent Fedora Core Development kernel I can following
soft-oops.. ( 2.6.12-1.1455_FC5smp )e100: eth0:
e100_watchdog: link up, 100Mbps, full-duplexBUG: soft lockup detected on CPU#0!Could this be a false positive? It's suspicious that the soft lockup detector was just merged to mainline then you got this.
I just downloaded 2.6.13-rc6-git and I don't see the merge of the soft lockup code. Is this a Fedora thing? If so, could someone point me to a link to download this Fedora kernel. I'm currently using Debian.
-- Steve
Quoted 4 lines · Steven Rostedt
I just downloaded 2.6.13-rc6-git and I don't see the merge of the soft lockup code. Is this a Fedora thing? If so, could someone point me to a link to download this Fedora kernel. I'm currently using Debian.
I seem to recall seeing fedora using voluntary preempt before it was merged.
Daniel
It looks like this might be an SMP race , it seem that both processors are in e100_down(). There is a while loop in e100_clean_cbs() that appears to have an unsafe looping condition .
It looks like cbs_avail might jump over params.cbs.count , then you would have to wait for a rollover . Is this a PREEMPT_NONE kernel?
This patch may help, but it's not a complete fix.
drivers/net/e100.c 2005-08-09 16:14:45.000000000 +0000 renamed from drivers/net/e100.c 2005-08-05 16:45:59.000000000 +0000 +1 -1
@@ -1393,7 +1393,7 @@ static inline int e100_tx_clean(struct n static void e100_clean_cbs(struct nic *nic) { if(nic->cbs) { - while(nic->cbs_avail != nic->params.cbs.count) { + while(nic->cbs_avail < nic->params.cbs.count) { struct cb *cb = nic->cb_to_clean; if(cb->skb) { pci_unmap_single(nic->pdev,
Quoted 64 lines · Matti Aarnio
Running very recent Fedora Core Development kernel I can following
soft-oops.. ( 2.6.12-1.1455_FC5smp )e100: eth0:
e100_watchdog: link up, 100Mbps, full-duplexBUG: soft lockup detected on CPU#0!Pid: 10743, comm: ifconfig
EIP: 0060:[<f88bf2f9>] CPU: 0
EIP is ate100_clean_cbs+0x2f/0x12b[e100]
EFLAGS: 00000293 Not tainted (2.6.12-1.1455_FC5smp)
EAX:495c7c2bEBX:495c7c2bECX:f6c311a0EDX: 00000000
ESI: 00000040 EDI:f6c30000EBP:f71a4b20DS: 007b ES: 007b
CR0:8005003bCR2:0804a544CR3:01e9cd80CR4:000006f0[<f88c0708>] e100_down+0x66/0x9a [e100] [<f88c1623>] e100_close+0xa/0xd [e100] [<c02b7adb>] dev_close+0x40/0x7e [<c02b8f59>] dev_change_flags+0x46/0xf5 [<c02f76b3>] devinet_ioctl+0x564/0x5df [<c02af22c>] sock_ioctl+0xc3/0x250 [<c02af169>] sock_ioctl+0x0/0x250 [<c01762ef>] do_ioctl+0x1f/0x6d [<c017648f>] vfs_ioctl+0x50/0x1c6 [<c0176662>] sys_ioctl+0x5d/0x6f [<c010394d>] syscall_call+0x7/0xb [<c014473f>] softlockup_tick+0x6f/0x80 [<c01085b8>] timer_interrupt+0x2d/0x75 [<c01448dd>] handle_IRQ_event+0x2e/0x5a [<c01449cb>] __do_IRQ+0xc2/0x127 [<c0105f7e>] do_IRQ+0x4e/0x86 ======================= [<c01160cc>] smp_apic_timer_interrupt+0xc1/0xca [<c0104382>] common_interrupt+0x1a/0x20 [<f88bf2f9>] e100_clean_cbs+0x2f/0x12b [e100] [<f88c0708>] e100_down+0x66/0x9a [e100] [<f88c1623>] e100_close+0xa/0xd [e100] [<c02b7adb>] dev_close+0x40/0x7e [<c02b8f59>] dev_change_flags+0x46/0xf5 [<c02f76b3>] devinet_ioctl+0x564/0x5df [<c02af22c>] sock_ioctl+0xc3/0x250 [<c02af169>] sock_ioctl+0x0/0x250 [<c01762ef>] do_ioctl+0x1f/0x6d [<c017648f>] vfs_ioctl+0x50/0x1c6 [<c0176662>] sys_ioctl+0x5d/0x6f [<c010394d>] syscall_call+0x7/0xbPreconditions for this are:
- E100 card stopped working for some reason (no idea why, it just does sometimes at this oldish 2x P-III machine)
- There are active datastreams running in and out
(around 0.2 Mbps out, multiple megabits in.)
- Commanding then "ifconfig eth0 down" results in what feels like system freezing, but it does recover in about 30-60 seconds (it takes long enough for me to sweat bullets...)
- While in freeze state, keyboard can go crazy, but mouse does respond, as well as tvtime shows bt848 captured live video.
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Quoted 6 lines · Daniel Walker
It looks like this might be an SMP race , it seem that both processors are in
e100_down(). There is a while loop ine100_clean_cbs()that appears to have an unsafe looping condition .It looks like
cbs_availmight jump over params.cbs.count , then you would have to wait for a rollover . Is this aPREEMPT_NONEkernel?
# CONFIG_PREEMPT is not set
# CONFIG_PREEMPT_BKL is not set
which is probably same as "NONE".
There is _one_ processor in down, but other may be in trying to send some data out, or otherwise polling the card.
However... while real bugs in their own sense, none of these are as important as original "card dies" thing, during a recovery of which all this soft-lockup merryment happens.
Also, as it happens only once a week or so (except when it happens right after another), testing code patches is rather slow. I can guess which things make it more likely, but I can't make it happen at will.
/Matti Aarnio
Quoted 81 lines
This patch may help, but it's not a complete fix.
drivers/net/e100.c 2005-08-09 16:14:45.000000000 +0000 renamed from drivers/net/e100.c 2005-08-05 16:45:59.000000000 +0000 +1
-1@@ -1393,7 +1393,7 @@ static inline int e100_tx_clean(struct n static void e100_clean_cbs(struct nic *nic) { if(nic->cbs) { - while(nic->cbs_avail != nic->params.cbs.count) { + while(nic->cbs_avail < nic->params.cbs.count) { struct cb *cb = nic->cb_to_clean; if(cb->skb) { pci_unmap_single(nic->pdev,Quoted 64 lines · Matti Aarnio
Running very recent Fedora Core Development kernel I can following
soft-oops.. ( 2.6.12-1.1455_FC5smp )e100: eth0:
e100_watchdog: link up, 100Mbps, full-duplexBUG: soft lockup detected on CPU#0!Pid: 10743, comm: ifconfig
EIP: 0060:[<f88bf2f9>] CPU: 0
EIP is ate100_clean_cbs+0x2f/0x12b[e100]
EFLAGS: 00000293 Not tainted (2.6.12-1.1455_FC5smp)
EAX:495c7c2bEBX:495c7c2bECX:f6c311a0EDX: 00000000
ESI: 00000040 EDI:f6c30000EBP:f71a4b20DS: 007b ES: 007b
CR0:8005003bCR2:0804a544CR3:01e9cd80CR4:000006f0[<f88c0708>] e100_down+0x66/0x9a [e100] [<f88c1623>] e100_close+0xa/0xd [e100] [<c02b7adb>] dev_close+0x40/0x7e [<c02b8f59>] dev_change_flags+0x46/0xf5 [<c02f76b3>] devinet_ioctl+0x564/0x5df [<c02af22c>] sock_ioctl+0xc3/0x250 [<c02af169>] sock_ioctl+0x0/0x250 [<c01762ef>] do_ioctl+0x1f/0x6d [<c017648f>] vfs_ioctl+0x50/0x1c6 [<c0176662>] sys_ioctl+0x5d/0x6f [<c010394d>] syscall_call+0x7/0xb [<c014473f>] softlockup_tick+0x6f/0x80 [<c01085b8>] timer_interrupt+0x2d/0x75 [<c01448dd>] handle_IRQ_event+0x2e/0x5a [<c01449cb>] __do_IRQ+0xc2/0x127 [<c0105f7e>] do_IRQ+0x4e/0x86 ======================= [<c01160cc>] smp_apic_timer_interrupt+0xc1/0xca [<c0104382>] common_interrupt+0x1a/0x20 [<f88bf2f9>] e100_clean_cbs+0x2f/0x12b [e100] [<f88c0708>] e100_down+0x66/0x9a [e100] [<f88c1623>] e100_close+0xa/0xd [e100] [<c02b7adb>] dev_close+0x40/0x7e [<c02b8f59>] dev_change_flags+0x46/0xf5 [<c02f76b3>] devinet_ioctl+0x564/0x5df [<c02af22c>] sock_ioctl+0xc3/0x250 [<c02af169>] sock_ioctl+0x0/0x250 [<c01762ef>] do_ioctl+0x1f/0x6d [<c017648f>] vfs_ioctl+0x50/0x1c6 [<c0176662>] sys_ioctl+0x5d/0x6f [<c010394d>] syscall_call+0x7/0xbPreconditions for this are:
- E100 card stopped working for some reason (no idea why, it just does sometimes at this oldish 2x P-III machine)
- There are active datastreams running in and out
(around 0.2 Mbps out, multiple megabits in.)
- Commanding then "ifconfig eth0 down" results in what feels like system freezing, but it does recover in about 30-60 seconds (it takes long enough for me to sweat bullets...)
- While in freeze state, keyboard can go crazy, but mouse does respond, as well as tvtime shows bt848 captured live video.
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
I have been working for days to get a recent kernel to work with these small-format UP Celeron 2Ghz (running at 1.33Ghz) motherboards that I am planning to use as thin clients. I'm doing a PXE boot, loading kernels, and trying to get networking to come up.
I eventually realized that the problem is that the e100 driver loads but does not allow any packet traffic. The system isn't crashed, but I do get transmit timeouts.
I've used kernels: 2.6.10, 2.6.11, and 2.6.12.4, stock with only the "squashfs" patch applied and compiled as 586/....
The interesting thing is that Ubuntu 5.04, booted "Live" on the box, works just fine with the e100 driver with a kernel shown as: "2.6.10-5-386". I'm going to work on pulling this kernel and its modules off to use.
Any help urgently appreciated.
sdw
Quoted 119 lines · Matti Aarnio
Quoted 8 lines · Daniel Walker
It looks like this might be an SMP race , it seem that both processors are in
e100_down(). There is a while loop ine100_clean_cbs()that appears to have an unsafe looping condition .It looks like
cbs_availmight jump over params.cbs.count , then you would have to wait for a rollover . Is this aPREEMPT_NONEkernel?#
CONFIG_PREEMPTis not set
#CONFIG_PREEMPT_BKLis not setwhich is probably same as "NONE".
There is _one_ processor in down, but other may be in trying to send some data out, or otherwise polling the card.
However... while real bugs in their own sense, none of these are as important as original "card dies" thing, during a recovery of which all this soft-lockup merryment happens.
Also, as it happens only once a week or so (except when it happens right after another), testing code patches is rather slow. I can guess which things make it more likely, but I can't make it happen at will.
/Matti Aarnio
Quoted 69 lines
This patch may help, but it's not a complete fix.
drivers/net/e100.c 2005-08-09 16:14:45.000000000 +0000 renamed from drivers/net/e100.c 2005-08-05 16:45:59.000000000 +0000 +1
-1@@ -1393,7 +1393,7 @@ static inline int e100_tx_clean(struct n static void e100_clean_cbs(struct nic *nic) { if(nic->cbs) { - while(nic->cbs_avail != nic->params.cbs.count) { + while(nic->cbs_avail < nic->params.cbs.count) { struct cb *cb = nic->cb_to_clean; if(cb->skb) { pci_unmap_single(nic->pdev,Quoted 50 lines · Matti Aarnio
Running very recent Fedora Core Development kernel I can following
soft-oops.. ( 2.6.12-1.1455_FC5smp )e100: eth0:
e100_watchdog: link up, 100Mbps, full-duplexBUG: soft lockup detected on CPU#0!Pid: 10743, comm: ifconfig
EIP: 0060:[<f88bf2f9>] CPU: 0
EIP is ate100_clean_cbs+0x2f/0x12b[e100]
EFLAGS: 00000293 Not tainted (2.6.12-1.1455_FC5smp)
EAX:495c7c2bEBX:495c7c2bECX:f6c311a0EDX: 00000000
ESI: 00000040 EDI:f6c30000EBP:f71a4b20DS: 007b ES: 007b
CR0:8005003bCR2:0804a544CR3:01e9cd80CR4:000006f0[<f88c0708>] e100_down+0x66/0x9a [e100] [<f88c1623>] e100_close+0xa/0xd [e100] [<c02b7adb>] dev_close+0x40/0x7e [<c02b8f59>] dev_change_flags+0x46/0xf5 [<c02f76b3>] devinet_ioctl+0x564/0x5df [<c02af22c>] sock_ioctl+0xc3/0x250 [<c02af169>] sock_ioctl+0x0/0x250 [<c01762ef>] do_ioctl+0x1f/0x6d [<c017648f>] vfs_ioctl+0x50/0x1c6 [<c0176662>] sys_ioctl+0x5d/0x6f [<c010394d>] syscall_call+0x7/0xb [<c014473f>] softlockup_tick+0x6f/0x80 [<c01085b8>] timer_interrupt+0x2d/0x75 [<c01448dd>] handle_IRQ_event+0x2e/0x5a [<c01449cb>] __do_IRQ+0xc2/0x127 [<c0105f7e>] do_IRQ+0x4e/0x86 ======================= [<c01160cc>] smp_apic_timer_interrupt+0xc1/0xca [<c0104382>] common_interrupt+0x1a/0x20 [<f88bf2f9>] e100_clean_cbs+0x2f/0x12b [e100] [<f88c0708>] e100_down+0x66/0x9a [e100] [<f88c1623>] e100_close+0xa/0xd [e100] [<c02b7adb>] dev_close+0x40/0x7e [<c02b8f59>] dev_change_flags+0x46/0xf5 [<c02f76b3>] devinet_ioctl+0x564/0x5df [<c02af22c>] sock_ioctl+0xc3/0x250 [<c02af169>] sock_ioctl+0x0/0x250 [<c01762ef>] do_ioctl+0x1f/0x6d [<c017648f>] vfs_ioctl+0x50/0x1c6 [<c0176662>] sys_ioctl+0x5d/0x6f [<c010394d>] syscall_call+0x7/0xbPreconditions for this are:
Quoted 16 lines
Quoted 6 lines
- E100 card stopped working for some reason (no idea why, it just does sometimes at this oldish 2x P-III machine)
- There are active datastreams running in and out (around 0.2 Mbps out, multiple megabits in.)
- Commanding then "ifconfig eth0 down" results in what feels like system freezing, but it does recover in about 30-60 secondsQuoted 10 lines
(it takes long enough for me to sweat bullets...)
- While in freeze state, keyboard can go crazy, but mouse does respond, as well as tvtime shows bt848 captured live video.
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Quoted 7 lines
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
begin:vcard
fn:Stephen Williams
n:Williams;Stephen
email;internet:[email protected]
tel;work:703-724-0118
tel;fax:703-995-0407
tel;pager:[email protected]
tel;home:703-729-5405
tel;cell:703-371-9362
x-mozilla-html:TRUE
version:2.1
end:vcard
I just noticed that the Ubuntu setup says "GSI 20(level,low) -> IRQ 20" whereas I remember my built kernels saying "No GSI...... IRQ 11". I'll investigate what that means and how to enable it. Pointers appreciated.
sdw
Quoted 6 lines · Stephen D. Williams
I have been working for days to get a recent kernel to work with these small-format UP Celeron 2Ghz (running at 1.33Ghz) motherboards that I am planning to use as thin clients. I'm doing a PXE boot, loading kernels, and trying to get networking to come up.
I eventually realized that the problem is that the e100 driver loads but does not allow any packet traffic. The system isn't crashed, but I do get transmit timeouts.
I've used kernels: 2.6.10, 2.6.11, and 2.6.12.4, stock with only the "squashfs" patch applied and compiled as 586/....
Quoted 136 lines
The interesting thing is that Ubuntu 5.04, booted "Live" on the box, works just fine with the e100 driver with a kernel shown as: "2.6.10-5-386". I'm going to work on pulling this kernel and its modules off to use.
Any help urgently appreciated.
sdw
Quoted 127 lines · Matti Aarnio
Quoted 6 lines · Daniel Walker
It looks like this might be an SMP race , it seem that both processors are in
e100_down(). There is a while loop ine100_clean_cbs()that appears to have an unsafe looping condition .
It looks likecbs_availmight jump over params.cbs.count , then you would have to wait for a rollover . Is this aPREEMPT_NONEkernel?#
CONFIG_PREEMPTis not set
#CONFIG_PREEMPT_BKLis not setwhich is probably same as "NONE".
There is _one_ processor in down, but other may be in trying to send some data out, or otherwise polling the card.
However... while real bugs in their own sense, none of these are as important as original "card dies" thing, during a recovery of which all this soft-lockup merryment happens.
Also, as it happens only once a week or so (except when it happens right after another), testing code patches is rather slow. I can guess which things make it more likely, but I can't make it happen at will.
/Matti Aarnio
Quoted 71 lines
This patch may help, but it's not a complete fix.
---
linux-2.6.12.orig/drivers/net/e100.c2005-08-05
16:45:59.000000000 +0000
+++linux-2.6.12/drivers/net/e100.c2005-08-09
16:14:45.000000000 +0000drivers/net/e100.c 2005-08-09 16:14:45.000000000 +0000 renamed from drivers/net/e100.c 2005-08-05 16:45:59.000000000 +0000 +1
-1@@ -1393,7 +1393,7 @@ static inline int e100_tx_clean(struct n static void e100_clean_cbs(struct nic *nic) { if(nic->cbs) { - while(nic->cbs_avail != nic->params.cbs.count) { + while(nic->cbs_avail < nic->params.cbs.count) { struct cb *cb = nic->cb_to_clean; if(cb->skb) { pci_unmap_single(nic->pdev,Quoted 50 lines · Matti Aarnio
Running very recent Fedora Core Development kernel I can following
soft-oops.. ( 2.6.12-1.1455_FC5smp )e100: eth0:
e100_watchdog: link up, 100Mbps, full-duplexBUG: soft lockup detected on CPU#0!Pid: 10743, comm: ifconfig
EIP: 0060:[<f88bf2f9>] CPU: 0
EIP is ate100_clean_cbs+0x2f/0x12b[e100]
EFLAGS: 00000293 Not tainted (2.6.12-1.1455_FC5smp)
EAX:495c7c2bEBX:495c7c2bECX:f6c311a0EDX: 00000000
ESI: 00000040 EDI:f6c30000EBP:f71a4b20DS: 007b ES: 007b
CR0:8005003bCR2:0804a544CR3:01e9cd80CR4:000006f0[<f88c0708>] e100_down+0x66/0x9a [e100] [<f88c1623>] e100_close+0xa/0xd [e100] [<c02b7adb>] dev_close+0x40/0x7e [<c02b8f59>] dev_change_flags+0x46/0xf5 [<c02f76b3>] devinet_ioctl+0x564/0x5df [<c02af22c>] sock_ioctl+0xc3/0x250 [<c02af169>] sock_ioctl+0x0/0x250 [<c01762ef>] do_ioctl+0x1f/0x6d [<c017648f>] vfs_ioctl+0x50/0x1c6 [<c0176662>] sys_ioctl+0x5d/0x6f [<c010394d>] syscall_call+0x7/0xb [<c014473f>] softlockup_tick+0x6f/0x80 [<c01085b8>] timer_interrupt+0x2d/0x75 [<c01448dd>] handle_IRQ_event+0x2e/0x5a [<c01449cb>] __do_IRQ+0xc2/0x127 [<c0105f7e>] do_IRQ+0x4e/0x86 ======================= [<c01160cc>] smp_apic_timer_interrupt+0xc1/0xca [<c0104382>] common_interrupt+0x1a/0x20 [<f88bf2f9>] e100_clean_cbs+0x2f/0x12b [e100] [<f88c0708>] e100_down+0x66/0x9a [e100] [<f88c1623>] e100_close+0xa/0xd [e100] [<c02b7adb>] dev_close+0x40/0x7e [<c02b8f59>] dev_change_flags+0x46/0xf5 [<c02f76b3>] devinet_ioctl+0x564/0x5df [<c02af22c>] sock_ioctl+0xc3/0x250 [<c02af169>] sock_ioctl+0x0/0x250 [<c01762ef>] do_ioctl+0x1f/0x6d [<c017648f>] vfs_ioctl+0x50/0x1c6 [<c0176662>] sys_ioctl+0x5d/0x6f [<c010394d>] syscall_call+0x7/0xbPreconditions for this are:
Quoted 16 lines
Quoted 6 lines
- E100 card stopped working for some reason (no idea why, it just does sometimes at this oldish 2x P-III machine)
- There are active datastreams running in and out (around 0.2 Mbps out, multiple megabits in.)
- Commanding then "ifconfig eth0 down" results in what feels like system freezing, but it does recover in about 30-60 secondsQuoted 9 lines
(it takes long enough for me to sweat bullets...)
- While in freeze state, keyboard can go crazy, but mouse does respond, as well as tvtime shows bt848 captured live video.
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
begin:vcard
fn:Stephen Williams
n:Williams;Stephen
email;internet:[email protected]
tel;work:703-724-0118
tel;fax:703-995-0407
tel;pager:[email protected]
tel;home:703-729-5405
tel;cell:703-371-9362
x-mozilla-html:TRUE
version:2.1
end:vcard
Quoted 3 lines · Stephen D. Williams
I just noticed that the Ubuntu setup says "GSI 20(level,low) -> IRQ 20" whereas I remember my built kernels saying "No GSI...... IRQ 11". I'll investigate what that means and how to enable it. Pointers appreciated.
That is most likely unrelated, but I had similar experiences at times. It turned out that something done recently in APIC management code did break things, but lattest version is again
working. For a while to have network card working I had to boot
with "noapic" option in my home SMP box.
In an UP box it is about same to boot as "noapic", but in SMP it does result in "one CPU does all interrupts" thingie. (In some rare cases it could be desirable, even.)
/Matti Aarnio
Quoted 24 lines
sdw
Quoted 20 lines · Stephen D. Williams
I have been working for days to get a recent kernel to work with these small-format UP Celeron 2Ghz (running at 1.33Ghz) motherboards that I am planning to use as thin clients. I'm doing a PXE boot, loading kernels, and trying to get networking to come up.
I eventually realized that the problem is that the e100 driver loads but does not allow any packet traffic. The system isn't crashed, but I do get transmit timeouts.
I've used kernels: 2.6.10, 2.6.11, and 2.6.12.4, stock with only the "squashfs" patch applied and compiled as 586/....
The interesting thing is that Ubuntu 5.04, booted "Live" on the box, works just fine with the e100 driver with a kernel shown as:
"2.6.10-5-386". I'm going to work on pulling this kernel and its modules off to use.Any help urgently appreciated.
sdw
"noapic" didn't work, nor did "noacpi", etc.
Going to 2.6.13-rc6.2 solved the problem (once I integrated udev, etc.).
The chipset is an Intel 8x0 something. Unfortunately, there is a heatsink semi-permanently installed over everything. Is there a /proc pseudofile that will give me good identifying chipset info to report here?
If there is a FAQ for this, we should post a message about it once in a while. Nothing here indicates chipset:
http://www.kernel.org/pub/linux/docs/lkml/reporting-bugs.html
The CPU is an Intel Celeron CPU 2.00GHz running at 1495.772 MHz, 128MB cache.
sdw
Quoted 13 lines · Matti Aarnio
Quoted 3 lines · Stephen D. Williams
I just noticed that the Ubuntu setup says "GSI 20(level,low) -> IRQ 20" whereas I remember my built kernels saying "No GSI...... IRQ 11". I'll investigate what that means and how to enable it. Pointers appreciated.
That is most likely unrelated, but I had similar experiences at times. It turned out that something done recently in APIC management code did break things, but lattest version is again
working. For a while to have network card working I had to boot
with "noapic" option in my home SMP box.
Quoted 31 lines
In an UP box it is about same to boot as "noapic", but in SMP it does result in "one CPU does all interrupts" thingie. (In some rare cases it could be desirable, even.)
/Matti Aarnio
Quoted 19 lines
sdw
Quoted 13 lines · Stephen D. Williams
I have been working for days to get a recent kernel to work with these small-format UP Celeron 2Ghz (running at 1.33Ghz) motherboards that I am planning to use as thin clients. I'm doing a PXE boot, loading kernels, and trying to get networking to come up.
I eventually realized that the problem is that the e100 driver loads but does not allow any packet traffic. The system isn't crashed, but I do get transmit timeouts.
I've used kernels: 2.6.10, 2.6.11, and 2.6.12.4, stock with only the "squashfs" patch applied and compiled as 586/....
The interesting thing is that Ubuntu 5.04, booted "Live" on the box, works just fine with the e100 driver with a kernel shown as: "2.6.10-5-386". I'm going to work on pulling this kernel and its modules off to use.
Any help urgently appreciated.
sdw
begin:vcard
fn:Stephen Williams
n:Williams;Stephen
email;internet:[email protected]
tel;work:703-724-0118
tel;fax:703-995-0407
tel;pager:[email protected]
tel;home:703-729-5405
tel;cell:703-371-9362
x-mozilla-html:TRUE
version:2.1
end:vcard
Quoted 3 lines · Stephen D. Williams
The chipset is an Intel 8x0 something. Unfortunately, there is a heatsink semi-permanently installed over everything. Is there a /proc pseudofile that will give me good identifying chipset info to report here?
you can show the chipset details with lspci
lspci -n will show device IDs and revision ids
interesting failure case on the e100, I haven't a clue whats going on.
netdev @ vger might be a good place to continue the discussion abut e100 issues.