Enabling 8xx debug mode
Hi Dan,
I know now that the BDI automatically enables debug mode by asserting the DSCK signal (available through the JTAG port). Is there any way to enable debugging mode purely via software?
44.3.1.2 Entering Debug Mode
By appropriately programming the development port during reset, debug mode can be entered immediately out of reset, thus allowing the user to debug a ROM-less system. If DSCK is asserted throughout SRESET assertion and then past SRESET negation, the processor takes a breakpoint exception and goes directly to debug mode instead of fetching the reset vector. To avoid entering debug mode after reset, DSCK must be negated no later than seven clock cycles after SRESET negates, allowing the processor to jump to the reset vector and begin normal execution. If debug mode is entered immediately after reset, as shown in Figure 44-7, ICR[DPI] is set. The user can enable events that can initiate debug mode and determine which events require regular interrupt handling.
Quoted 3 lines · Marcelo Tosatti
I know now that the BDI automatically enables debug mode by asserting the DSCK signal (available through the JTAG port). Is there any way to enable debugging mode purely via software?
I'm not sure I really understand the question, but I'll give some answers anyway :-) The 8xx has the development/debug support, which is a bunch of registers that allow setting instruction/data breakpoints and so on. These are accessible from software, along with other standard PowerPC debug (like single step).
The DSCK is a BDM/JTAG clock signal, and along with the other signals allow the clocking of instructions and data through the BDM pins. One of the things you can do is strobe in instructions that will set these same breakpoint or other debug registers as are accessible from software running on the part.
So, if you have software running on the processor, you can do the same things. Obviously, if you are stuck someplace you need to get the attention of the processor. You can do this with some interrupt like kgdb does, then use the debug interface to help.
Does this make sense?
Thanks.
-- Dan
Quoted 19 lines · Dan Malek
Quoted 3 lines · Marcelo Tosatti
I know now that the BDI automatically enables debug mode by asserting the DSCK signal (available through the JTAG port). Is there any way to enable debugging mode purely via software?
I'm not sure I really understand the question, but I'll give some answers anyway :-) The 8xx has the development/debug support, which is a bunch of registers that allow setting instruction/data breakpoints and so on. These are accessible from software, along with other standard PowerPC debug (like single step).
The DSCK is a BDM/JTAG clock signal, and along with the other signals allow the clocking of instructions and data through the BDM pins. One of the things you can do is strobe in instructions that will set these same breakpoint or other debug registers as are accessible from software running on the part.
Quoted 6 lines
So, if you have software running on the processor, you can do the same things. Obviously, if you are stuck someplace you need to get the attention of the processor. You can do this with some interrupt like kgdb does, then use the debug interface to help.
Does this make sense?
Yep.. my misunderstanding was the debug mode can only be turned ON by asserting the DSCK signal during SRESET as the manual says.
That's fine.
I'm trying to use the debugging registers - seem to work (the example is a data breakpoint). Just need a real interrupt handler, the current one breaks at trap but since the console is not yet initialized I et no output (that sucks).
It panic()'s, as expected.
Index: arch/ppc/boot/simple/head.S
===================================================================
RCS file: /mnt/test1/tslinux_mv21/linux-2.6/arch/ppc/boot/simple/head.S,v retrieving revision 1.3
ppc/boot/simple/head.S +11 -0
@@ -130,7 +130,18 @@ * processor correctly. Don't do this if you want to debug * using a BDM device. */ +#define CONFIG_8xx_DEBUG +#ifdef CONFIG_8xx_DEBUG + /* bit 2: Checkstop enable + * bit 3: Machine check interrupt enable + * bits [28,30]: load/store, instruction and external breakpoint resp. + * bit 31: Development port nonmaskable request enable + */ + li r4,0x000F + lis r4,0x3000 +#else li r4,0 /* Zero DER to prevent FRZ */ +#endif mtspr SPRN_DER,r4 #endif
Index: arch/ppc/kernel/head_8xx.S
===================================================================
RCS file: /mnt/test1/tslinux_mv21/linux-2.6/arch/ppc/kernel/head_8xx.S,v retrieving revision 1.4
ppc/kernel/head_8xx.S +11 -1
@@ -554,7 +554,17 @@ * support of breakpoints and such. Someday I will get around to * using them. */ - EXCEPTION(0x1c00, Trap_1c, UnknownException, EXC_XFER_EE) +. = 0x1c00 +DataBreakpoint: + + EXCEPTION_PROLOG + mfspr r4,DAR + stw r4,_DAR(r11) + mfspr r5,DSISR + stw r5,_DSISR(r11) + trap + +/* EXCEPTION(0x1c00, Trap_1c, UnknownException, EXC_XFER_EE) */ EXCEPTION(0x1d00, Trap_1d, UnknownException, EXC_XFER_EE) EXCEPTION(0x1e00, Trap_1e, UnknownException, EXC_XFER_EE) EXCEPTION(0x1f00, Trap_1f, UnknownException, EXC_XFER_EE)
Index: arch/ppc/kernel/misc.S
===================================================================
RCS file: /mnt/test1/tslinux_mv21/linux-2.6/arch/ppc/kernel/misc.S,v retrieving revision 1.4
ppc/kernel/misc.S +25 -0
@@ -1276,6 +1276,31 @@ addi r1,r1,16 blr +#define LCTRL1 156 +#define LCTRL2 157 +#define CMPE 152 +#define CMPF 153 + +/* initrd_watchpoint(unsigned long start, unsigned long end) */ +_GLOBAL(initrd_watchpoint) + stw r5, 4(r0) + + mtspr CMPE, r3 + mtspr CMPF, r4 + + li r5, 0x0000 + lis r5, 0xD4F0 + + mtspr LCTRL1, r5 + + li r5, 0x0002 + lis r5, 0x8A00 + + mtspr LCTRL2, r5 + + lwz r5, 4(r0) + blr + /* * This routine is just here to keep GCC happy - sigh... */
Index: arch/ppc/syslib/m8xx_setup.c
===================================================================
RCS file: /mnt/test1/tslinux_mv21/linux-2.6/arch/ppc/syslib/m8xx_setup.c,v retrieving revision 1.12
ppc/syslib/m8xx_setup.c +5 -0
@@ -70,6 +70,8 @@unsigned char __res[sizeof (bd_t)]; +extern void initrd_watchpoint (unsigned long start,unsigned long end); +extern void m8xx_ide_init (void );extern unsigned long find_available_memory (void );
@@ -618,6 +620,9 @@ }#endif /* CONFIG_BLK_DEV_INITRD */ /* take care of cmd line */ + +//initrd_watchpoint(initrd_start, initrd_end); +if ( r6 ) { *(char *)(r7+KERNELBASE ) =0 ;
main.c +3 -0
@@ -453,6 +453,8 @@* Activate the first processor. */ +extern void initrd_watchpoint (unsigned long start,unsigned long end); + asmlinkage void __init start_kernel(void) {char * command_line;
@@ -495,6 +497,7 @@ __stop___param - __start___param, &unknown_bootoption);sort_main_extable (); +initrd_watchpoint (initrd_start, initrd_end);trap_init ();rcu_init ();init_IRQ ();
Quoted 2 lines · Marcelo Tosatti
I'm trying to use the debugging registers - seem to work (the example is a data breakpoint). Just need a real interrupt handler,...
yes, that's the right idea. It's easier with a BDI2000, though :-)
Have fun!
-- Dan
client and server implementation
For one perticular implementation, I need to work on a client and server program on 8xx family of ppc. One of the main goal is to keep the code size minimum. Has anyone already implemented similar things on ppc. Can anyone give me pointers for the same.
Also, is there any trimmed version of pcap and libnet available for 8xx ppc?
-sainink
____________________________________________________
Start your day with Yahoo! - make it your home page
http://www.yahoo.com/r/hs