Skip to contentSkip to conversation

pm2 driver

PATCH Peter 'p2' De Schrijver 2 participants 2 messages Sep 27, 2005 – Oct 5, 2005 Framebuffer layer

lore
Share & tools
lore
#0 lore raw

Hi,

Attached is a small patch which configures the correct memory clock and timings on the Elsa Winner 2000 Office pm2 based card. This is necessary when the card is used on a platform which does not support PC style BIOS initialization.

Thanks,

Peter (p2).

Signature · 1 line
goa is a state of mind
drivers/video/pm2fb.c +17 -1
diff -urN -x asm -x scripts -x config linux/drivers/video/pm2fb.c linux-my/drivers/video/pm2fb.c
@@ -52,7 +52,7 @@
 #error "Only generic PCI cards supported."
 #endif
 
-#undef PM2FB_MASTER_DEBUG
+#define PM2FB_MASTER_DEBUG 1
 #ifdef PM2FB_MASTER_DEBUG
 #define DPRINTK(a,b...)	printk(KERN_DEBUG "pm2fb: %s: " a, __FUNCTION__ , ## b)
 #else
@@ -1121,6 +1121,22 @@
 		default_par->mem_control, default_par->boot_address,
 		default_par->mem_config);
 
+	if(default_par->mem_control == 0 &&
+		default_par->boot_address == 0x31 &&
+		default_par->mem_config == 0x259fffff &&
+		pdev->subsystem_vendor == 0x1048 &&
+		pdev->subsystem_device == 0x0a31) {
+		DPRINTK("subsystem_vendor: %04x, subsystem_device: %04x\n",
+			pdev->subsystem_vendor, pdev->subsystem_device);
+		DPRINTK("We have not been initialized by VGA BIOS "
+			"and are running on an Elsa Winner 2000 Office\n");
+		DPRINTK("Initializing card timings manually...\n");
+		default_par->mem_control=0;
+		default_par->boot_address=0x20;
+		default_par->mem_config=0xe6002021;
+		default_par->memclock=100000;
+	}
+
 	/* Now work out how big lfb is going to be. */
 	switch(default_par->mem_config & PM2F_MEM_CONFIG_RAM_MASK) {
 	case PM2F_MEM_BANKS_1:
#1 lore raw
Quoted 4 lines · On Tuesday 27 September 2005 19:46, Peter 'p2' De Schrijver wrote:

Attached is a small patch which configures the correct memory clock and timings on the Elsa Winner 2000 Office pm2 based card. This is necessary when the card is used on a platform which does not support PC style BIOS initialization.

Thanks for that, Peter - and sorry for the delay in getting back to you. I've been away from home for work purposes, and am just now catching up on back emails.

I am curious about one thing. The initial mem control, mem config etc. values that you check for - I assume they are what you observe on your hardware. Will they be the same on other hardware, do you know? I must check my TVP4020 docs...

How would you feel if instead I added a driver parameter to force initialisation instead of looking for particular initial values?

Out of interest, what have you got the card plugged into?

Signature · 7 lines
Jim Hague - [email protected]          Never trust a computer you can't lift.


-------------------------------------------------------
This SF.Net email is sponsored by:
Power Architecture Resource Center: Free content, downloads, discussions,
and more. http://solutions.newsforge.com/ibmarch.tmpl