3c900 boot-time kernel commandline parameters in 2.4.25
How do I tell Linux kernel 2.4.25 on boot-time kernel commandline to switch my eth0
-----------------------------------------------------------------------
Bus 1, device 3, function 0:
Ethernet controller: 3Com Corporation 3c900 Combo [Boomerang] (rev
0).
IRQ 11.
Master Capable. Latency=32. Min Gnt=3.Max Lat=8.
I/O at 0xc000 [0xc03f].-----------------------------------------------------------------------
to TP transceiver and 10/100 autonegotiation?
I looked into Documentation/00-INDEX and into kernel-parameters.txt and found just
" ether= [HW,NET] Ethernet cards parameters (irq,
base_io_addr, mem_start, mem_end, name. (mem_start is often overloaded to mean something different and driver-specific).
"
which neither doesn't answer my question neither point to any documentation where my question could be answered.
CL<
Quoted 16 lines · Karel Kulhavy
How do I tell Linux kernel 2.4.25 on boot-time kernel commandline to switch my eth0
-----------------------------------------------------------------------
Bus 1, device 3, function 0:
Ethernet controller: 3Com Corporation 3c900 Combo [Boomerang] (rev
0).IRQ 11. Master Capable. Latency=32. Min Gnt=3.Max Lat=8. I/O at 0xc000 [0xc03f].-----------------------------------------------------------------------
to TP transceiver and 10/100 autonegotiation?
I looked into
Documentation/00-INDEXand into kernel-parameters.txt and found just
Quoted 8 lines
" ether= [HW,NET] Ethernet cards parameters (irq,
base_io_addr,mem_start,mem_end, name. (mem_startis often overloaded to mean something different and driver-specific).
"which neither doesn't answer my question neither point to any documentation where my question could be answered.
Yes, there are lots of drivers where it is necessary to look in the driver source file to determine actual parameter usage.
For the 3c59x driver, mem_start is overloaded (as in the doc above) as:
0x8000 debug level 70x4000 debug level 20x0400 enable WOL0x0200 full duplex0x0010 bus master
0x000m media override value, index into media_table:
0: { "10baseT", Media_10TP,0x08, XCVR_10base2, (14*HZ)/10},
1: { "10Mbs AUI", Media_SQE, 0x20, XCVR_Default, (1*HZ)/10},
2: { "undefined", 0, 0x80, XCVR_10baseT, 10000},
3: { "10base2", 0, 0x10, XCVR_AUI, (1*HZ)/10},
4: { "100baseTX", Media_Lnk, 0x02, XCVR_100baseFx, (14*HZ)/10},
5: { "100baseFX", Media_Lnk, 0x04, XCVR_MII, (14*HZ)/10},
6: { "MII", 0, 0x41, XCVR_10baseT, 3*HZ },
7: { "undefined", 0, 0x01, XCVR_10baseT, 10000},
8: { "Autonegotiate", 0, 0x41, XCVR_10baseT, 3*HZ},
9: { "MII-External", 0, 0x41, XCVR_10baseT, 3*HZ },
10: { "Default", 0, 0xFF, XCVR_10baseT, 10000},
so don't use 2 or 7 for the media override value.
In your case, I guess you want mem_start=8.
Signature · 1 line
~Randy