ieee1394: sbp2: sbp2util_node_write_no_wait failed
Hi,
I get the above message frequently while copying data (around 200000 mail files, 2GB) from my laptop to an external harddisk via ieee1394. The ieee system completely deadlocked with 2.6.13 without the chance to umount or reuse the device. Now I upgraded to 2.6.14-rc5 and I still get the error followed by a 10sec pause or so, but then the copying continues. I will have to check if it copied all data correctly, though.
When attaching the device this is what the kernel says:
kernel: ieee1394: Current remote IRM is not 1394a-2000 compliant, resetting... kernel: ieee1394: Error parsing configrom for node 0-00:1023 kernel: ieee1394: Node changed: 0-00:1023 -> 0-01:1023 kernel: ieee1394: Node added: ID:BUS[0-00:1023] GUID[0000000e000031d1] kernel: scsi1 : SCSI emulation for IEEE-1394 SBP-2 Devices kernel: ieee1394: sbp2: Logged into SBP-2 device kernel: ieee1394: Node 0-00:1023: Max speed [S400] - Max payload [2048] kernel: Vendor: WDC WD20 Model: 00JB-00GVC0 Rev: kernel: Type: Direct-Access-RBC ANSI SCSI revision: 04 kernel: Attached scsi generic sg0 at scsi1, channel 0, id 0, lun 0, type 14 kernel: SCSI device sda: 390721968 512-byte hdwr sectors (200050 MB) kernel: sda: asking for cache data failed kernel: sda: assuming drive cache: write through kernel: SCSI device sda: 390721968 512-byte hdwr sectors (200050 MB) kernel: sda: asking for cache data failed kernel: sda: assuming drive cache: write through kernel: sda: sda1 sda2 sda3 sda4 kernel: Attached scsi disk sda at scsi1, channel 0, id 0, lun 0
And the complete error message:
kernel: ieee1394: sbp2: sbp2util_node_write_no_wait failed. kernel:
kernel: ieee1394: sbp2: aborting sbp2 command
kernel: scsi1 : destination target 0, lun 0
kernel: command: cdb[0]=0x2a: 2a 00 09 76 04 73 00 00 01 00
kernel: ieee1394: sbp2: sbp2util_node_write_no_wait failed. kernel:
kernel: ieee1394: sbp2: aborting sbp2 command
kernel: scsi1 : destination target 0, lun 0
kernel: command: cdb[0]=0x2a: 2a 00 08 5f 83 54 00 00 01 00
[lots more of that, the command hex code changes everytime]
I have a preemt kernel:CONFIG_PREEMPT=yCONFIG_PREEMPT_BKL=y
and the 1000hz timer:CONFIG_HZ_1000=yCONFIG_HZ=1000CONFIG_PHYSICAL_START=0x100000
and the following is the ieee config:CONFIG_IEEE1394=mCONFIG_IEEE1394_OHCI1394=m
CONFIG_IEEE1394_VIDEO1394=mCONFIG_IEEE1394_SBP2=mCONFIG_IEEE1394_SBP2_PHYS_DMA=y
# CONFIG_IEEE1394_ETH1394 is not setCONFIG_IEEE1394_DV1394=mCONFIG_IEEE1394_RAWIO=m
# CONFIG_IEEE1394_CMP is not set
Please tell me if you need more info, I'd like to provide all the help needed to fix this issue.
Cheers,
Signature · 5 lines
Michael Brade; KDE Developer, Student of Computer Science |-mail: echo brade !#|tr -d "c oh"|s\e\d 's/e/\@/2;s/$/.org/;s/bra/k/2' °--web: http://www.kde.org/people/michaelb.html KDE 3: The Next Generation in Desktop Experience
Michael> I get the above message frequently while copying data (around Michael> 200000 mail files, 2GB) from my laptop to an external Michael> harddisk via ieee1394. The ieee system completely deadlocked Michael> with 2.6.13 without the chance to umount or reuse the Michael> device. Now I upgraded to 2.6.14-rc5 and I still get the Michael> error followed by a 10sec pause or so, but then the copying Michael> continues. I will have to check if it copied all data Michael> correctly, though.
One thing I suggest right off the bat is to make sure that firmware on your external enclosure is updated to the latest/greatest. Alot of vendors (esp those using the Prolific chipset) don't get it right initially.
Other than that, at least it's recovering better now and not locking up!
John
Quoted 8 lines · John Stoffel
Michael> I get the above message frequently while copying data (around Michael> 200000 mail files, 2GB) from my laptop to an external Michael> harddisk via ieee1394. The ieee system completely deadlocked Michael> with 2.6.13 without the chance to umount or reuse the Michael> device. Now I upgraded to 2.6.14-rc5 and I still get the Michael> error followed by a 10sec pause or so, but then the copying Michael> continues. I will have to check if it copied all data Michael> correctly, though.
Ok, update and good news: it did actually copy the files properly, reading and checking worked without errors.
Quoted 4 lines
One thing I suggest right off the bat is to make sure that firmware on your external enclosure is updated to the latest/greatest. Alot of vendors (esp those using the Prolific chipset) don't get it right initially.
Good guess and damn, yes, I've got the Icy Box IB-351-UE which has the prolific chipset, I guess it's the (cursed) PL3507. [The IcyBox FAQ says:
IB-350/351/360UE Prolific (PL3507) - Agere (FW8028)]
However, I've read that they had problems in 2004 and that all new devices (starting from October 2004) have the updated firmware already.
I have also found some of your posts from 2004 on lkml about the prolific chipset, actually anything I found is mostly from 2004 :-/
So sorry for the dumb question, but do I check if I've got the newest firmware without windows? I had a look at www.icybox.de but found no firmware for ib-351, only for ib-350 and that one is from Dec 2004.
And even if I've got the newest firmware already, does the prolific stuff work by now or should I chuck it out the window?
Quoted 2 lines
Other than that, at least it's recovering better now and not locking up!
Yes, which makes the thing at least usable now :-) But it still takes forever since it happens every 30-120 seconds. And just now the HD started making *really* strange noises after I let it sit there idle for 10-20 minutes or so. The I quickly read some files and it stopped. I'm scared of my data...
Thanks for your help,
Signature · 5 lines
Michael Brade; KDE Developer, Student of Computer Science |-mail: echo brade !#|tr -d "c oh"|s\e\d 's/e/\@/2;s/$/.org/;s/bra/k/2' °--web: http://www.kde.org/people/michaelb.html KDE 3: The Next Generation in Desktop Experience
Quoted 6 lines
Quoted 6 lines
Quoted 1 line
Quoted 1 line
Quoted 1 line
"Michael" == Michael Brade <[email protected]> writes:
One thing I suggest right off the bat is to make sure that firmware on your external enclosure is updated to the latest/greatest. Alot of vendors (esp those using the Prolific chipset) don't get it right initially.
Michael> Good guess and damn, yes, I've got the Icy Box IB-351-UE Michael> which has the prolific chipset, I guess it's the (cursed) Michael> PL3507. [The IcyBox FAQ says: IB-350/351/360UE Prolific Michael> (PL3507) - Agere (FW8028)]
I've got the same box, and I've given up on the firewire side of things and I just use the USB port now. But it's just my backup box, so I don't really use it too much.
Michael> However, I've read that they had problems in 2004 and that Michael> all new devices (starting from October 2004) have the updated Michael> firmware already.
Check anyway... I think I posted recently about my luck in getting the USB side working with 2.6.12+ once I updated the firmware on the chipset, which was a pain.
Michael> I have also found some of your posts from 2004 on lkml about Michael> the prolific chipset, actually anything I found is mostly Michael> from 2004 :-/
Yeah, from what I've been reading, the Prolific chipset sucked even for Windows users, at least until the latest firmware. Goto these pages:
http://tech.prolific.com.tw/visitor/v_filebrw_result.asp http://forum.rpc1.org/viewtopic.php?t=25140&postdays=0&postorder=asc&&start=25&sid=6801466c15ef74f35a490bbdb423cf37
The second one is a forum which had some useful info.
Michael> So sorry for the dumb question, but do I check if I've got Michael> the newest firmware without windows? I had a look at Michael> www.icybox.de but found no firmware for ib-351, only for Michael> ib-350 and that one is from Dec 2004.
You need to go by chipset, not by enclosure. I poked on my system, but there's nothing obvious about how to get the firmware level in the output of 'lsusb'. Sorry.
Michael> And even if I've got the newest firmware already, does the Michael> prolific stuff work by now or should I chuck it out the Michael> window?
It works with USB, I don't know about firewire since I've just chucked that for now. Which is why I got the dual input setup, USB/Firewire. Haven't tried the firewire on a Windows box either since the upgrade, might one of these days, but I'm in no rush.
John
Quoted 9 lines · John Stoffel
Yeah, from what I've been reading, the Prolific chipset sucked even for Windows users, at least until the latest firmware. Goto these pages:
http://tech.prolific.com.tw/visitor/v_filebrw_result.asp http://forum.rpc1.org/viewtopic.php?t=25140&postdays=0&postorder=asc&&start=25&sid=6801466c15ef74f35a490bbdb423cf37
The second one is a forum which had some useful info.
Thank you so much for your help! It probably won't make my device work with ieee1394 out of the blue but it sure got me out of my ignorance!
Quoted 5 lines
Michael> And even if I've got the newest firmware already, does the Michael> prolific stuff work by now or should I chuck it out the Michael> window?
It works with USB
Ok, I will try that then. I have only USB 1.1 on my laptop so I guess either I'll get rid of the icy box (what a name..) or get a USB 2.0 PCMCIA card.
Cheers,
Signature · 5 lines
Michael Brade; KDE Developer, Student of Computer Science |-mail: echo brade !#|tr -d "c oh"|s\e\d 's/e/\@/2;s/$/.org/;s/bra/k/2' °--web: http://www.kde.org/people/michaelb.html KDE 3: The Next Generation in Desktop Experience
Quoted 4 lines · John Stoffel
It works with USB, I don't know about firewire since I've just chucked that for now. Which is why I got the dual input setup, USB/Firewire. Haven't tried the firewire on a Windows box either since the upgrade, might one of these days, but I'm in no rush.
Ok, just a little update as it might be interesting for others, too: yesterday a friend came surprisingly to my place because his server didn't work properly (we worked till 4am...) and he brought a windows laptop! So I searched a bit more and found a new firmware for the PL3507, dated September 2005, and flashed it.
But, alas, to no avail. The problem persists, when writing to the HD I get the above error and the hd/kernel hangs for some time until it resumes. So my guess is, this might really be a bug in our kernel and not the firmware?
And I haven't even mentioned yet that I have a DVD writer in an icybox as well, I flashed this one too but still can't even *read* from any CD/DVD. There the kernel hangs itself for a while and prints
kernel: ieee1394: sbp2: aborting sbp2 command kernel: scsi3 : destination target 0, lun 0 kernel: command: cdb[0]=0x28: 28 00 00 00 10 6f 00 00 01 00 kernel: ieee1394: sbp2: aborting sbp2 command kernel: scsi3 : destination target 0, lun 0 kernel: command: cdb[0]=0x0: 00 00 00 00 00 00 kernel: ieee1394: sbp2: reset requested kernel: ieee1394: sbp2: Generating sbp2 fetch agent reset kernel: ieee1394: sbp2: aborting sbp2 command kernel: scsi3 : destination target 0, lun 0 kernel: command: cdb[0]=0x0: 00 00 00 00 00 00 kernel: ieee1394: sbp2: reset requested kernel: ieee1394: sbp2: Generating sbp2 fetch agent reset kernel: ieee1394: sbp2: aborting sbp2 command kernel: scsi3 : destination target 0, lun 0 kernel: command: cdb[0]=0x0: 00 00 00 00 00 00 kernel: ieee1394: sbp2: reset requested kernel: ieee1394: sbp2: Generating sbp2 fetch agent reset kernel: ieee1394: sbp2: aborting sbp2 command kernel: scsi3 : destination target 0, lun 0 kernel: command: cdb[0]=0x0: 00 00 00 00 00 00 kernel: scsi: Device offlined - not ready after error recovery: host 3 channel
0 id 0 lun 0
kernel: sr 3:0:0:0: SCSI error: return code = 0x50000
kernel: end_request: I/O error, dev sr0, sector 16828
kernel: Buffer I/O error on device sr0, logical block 4207
kernel: scsi3 (0:0): rejecting I/O to offline device
Oh well. For now I most definitely have to look for the USB alternative.
Cheers,
Signature · 5 lines
Michael Brade; KDE Developer, Student of Computer Science |-mail: echo brade !#|tr -d "c oh"|s\e\d 's/e/\@/2;s/$/.org/;s/bra/k/2' °--web: http://www.kde.org/people/michaelb.html KDE 3: The Next Generation in Desktop Experience
Alright, very bad news:
Quoted 2 lines · John Stoffel
Yeah, from what I've been reading, the Prolific chipset sucked even for Windows users, at least until the latest firmware.
Because of this I gave my prolific stuff back (they actually took it back, great) and got an Oxford 911. I *STILL* get the same kind of errors though! Here's what the syslog says again:
kernel: ieee1394: The root node is not cycle master capable; selecting a new root node and resetting.
kernel: ieee1394: Error parsing configrom for node 0-00:1023 kernel: ieee1394: Node changed: 0-00:1023 -> 0-01:1023 kernel: ieee1394: Node added: ID:BUS[0-00:1023] GUID[0030e001e0454647] kernel: SCSI subsystem initialized kernel: sbp2: $Rev: 1306 $ Ben Collins <[email protected]> kernel: ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1) kernel: ieee1394: sbp2: Try serialize_io=0 for better performance kernel: scsi0 : SCSI emulation for IEEE-1394 SBP-2 Devices kernel: ieee1394: sbp2: Logged into SBP-2 device kernel: ieee1394: Node 0-00:1023: Max speed [S400] - Max payload [2048] kernel: Vendor: WDC WD20 Model: 00JB-00GVC0 Rev: 08.0 kernel: Type: Direct-Access-RBC ANSI SCSI revision: 04 kernel: SCSI device sda: 390721968 512-byte hdwr sectors (200050 MB) kernel: sda: asking for cache data failed kernel: sda: assuming drive cache: write through kernel: SCSI device sda: 390721968 512-byte hdwr sectors (200050 MB) kernel: sda: asking for cache data failed kernel: sda: assuming drive cache: write through kernel: sda: sda1 sda2 sda3 sda4 kernel: Attached scsi disk sda at scsi0, channel 0, id 0, lun 0 kernel: XFS mounting filesystem sda1 kernel: Ending clean XFS mount for filesystem: sda1 kernel: XFS mounting filesystem sda2 kernel: Ending clean XFS mount for filesystem: sda2 kernel: ieee1394: sbp2: sbp2util_node_write_no_wait failed.
kernel:
kernel: ieee1394: sbp2: aborting sbp2 command
kernel: scsi0 : destination target 0, lun 0
kernel: command: cdb[0]=0x2a: 2a 00 06 48 37 51 00 00 01 00
kernel: ieee1394: sbp2: sbp2util_node_write_no_wait failed. kernel:
kernel: ieee1394: sbp2: aborting sbp2 command
kernel: scsi0 : destination target 0, lun 0
kernel: command: cdb[0]=0x2a: 2a 00 06 95 d7 31 00 00 01 00
kernel: ieee1394: sbp2: sbp2util_node_write_no_wait failed. kernel:
kernel: ieee1394: sbp2: aborting sbp2 command
kernel: scsi0 : destination target 0, lun 0
kernel: command: cdb[0]=0x2a: 2a 00 06 9b 52 c1 00 00 01 00
kernel: ieee1394: sbp2: sbp2util_node_write_no_wait failed. kernel:
kernel: ieee1394: sbp2: aborting sbp2 command
kernel: scsi0 : destination target 0, lun 0
kernel: command: cdb[0]=0x2a: 2a 00 06 9c 3a a1 00 00 01 00
kernel: ieee1394: sbp2: sbp2util_node_write_no_wait failed. kernel:
kernel: ieee1394: sbp2: aborting sbp2 command
kernel: scsi0 : destination target 0, lun 0
kernel: command: cdb[0]=0x2a: 2a 00 06 3f 17 80 00 00 01 00
I'm running kernel 2.6.14-rc5. Does anyone have any ideas about how to fix this? Is anybody actually using a harddisk on ieee1394 without problems? Please CC me on replies, thanks.
Thanks,
Signature · 5 lines
Michael Brade; KDE Developer, Student of Computer Science |-mail: echo brade !#|tr -d "c oh"|s\e\d 's/e/\@/2;s/$/.org/;s/bra/k/2' °--web: http://www.kde.org/people/michaelb.html KDE 3: The Next Generation in Desktop Experience