sata_uli fails to see harddisks on an ASRock 939Dual-SATA2 board
On an ASRock 939Dual-SATA2 board, the sata_uli driver recognizes the onboard SATA controller (PCI ID 10b9:5289 rev 10, Subsystem 1849:5289), but fails to see an attached harddisk (the BIOS identifies the harddisk correctly, so a hardware failure is unlikely). sata_uli apparently sees _something_ is attached, but doesn't get further. dmesg says:
libata version 1.20 loaded.sata_uli 0000:00:12.1: version 0.5
GSI 18 sharing vector 0xD1 and IRQ 18
ACPI: PCI Interrupt 0000:00:12.1[A] -> GSI 19 (level, low) -> IRQ 209
ata1: SATA max UDMA/133 cmd 0xEC00 ctl 0xE082 bmdma 0xD880 irq 209
ata2: SATA max UDMA/133 cmd 0xE000 ctl 0xDC02 bmdma 0xD888 irq 209
ata1: SATA link up 1.5 Gbps (SStatus 113)
scsi0 : sata_uli
ata2: SATA link down (SStatus 0)
scsi1 : sata_uli
No disks are found, even though the link (on ata1) is detected.
Verified both with an x86 and an x86_64 kernel, and both 2.6.15-rc5 and 2.6.15-rc5-mm2.
Any ideas?
Quoted 17 lines · Bernhard Rosenkraenzer
On an ASRock 939Dual-SATA2 board, the
sata_ulidriver recognizes the onboard SATA controller (PCI ID 10b9:5289 rev 10, Subsystem 1849:5289), but fails to see an attached harddisk (the BIOS identifies the harddisk correctly, so a hardware failure is unlikely).sata_uliapparently sees _something_ is attached, but doesn't get further. dmesg says:libata version 1.20 loaded.
sata_uli0000:00:12.1: version 0.5
GSI 18 sharing vector0xD1and IRQ 18
ACPI: PCI Interrupt 0000:00:12.1[A] -> GSI 19 (level, low) -> IRQ 209
ata1: SATA max UDMA/133 cmd0xEC00ctl0xE082bmdma0xD880irq 209
ata2: SATA max UDMA/133 cmd0xE000ctl0xDC02bmdma0xD888irq 209
ata1: SATA link up 1.5 Gbps (SStatus 113)
scsi0 :sata_uli
ata2: SATA link down (SStatus 0)
scsi1 :sata_uli
Quoted 6 lines
No disks are found, even though the link (on ata1) is detected.
Verified both with an x86 and an
x86_64kernel, and both 2.6.15-rc5 and 2.6.15-rc5-mm2.Any ideas?
I've seen this and thought that it was MSI interrupt related. I have suggested disabling CONFIG_PCI_MSI, but (iirc) that did not fix the problem for someone who tested it. I'll fiddle with it some... no promises.
Signature · 1 line
~Randy
Hi,
Quoted 17 lines · Bernhard Rosenkraenzer
On an ASRock 939Dual-SATA2 board, the
sata_ulidriver recognizes the onboard SATA controller (PCI ID 10b9:5289 rev 10, Subsystem 1849:5289), but fails to see an attached harddisk (the BIOS identifies the harddisk correctly, so a hardware failure is unlikely).sata_uliapparently sees _something_ is attached, but doesn't get further. dmesg says:libata version 1.20 loaded.
sata_uli0000:00:12.1: version 0.5
GSI 18 sharing vector0xD1and IRQ 18
ACPI: PCI Interrupt 0000:00:12.1[A] -> GSI 19 (level, low) -> IRQ 209
ata1: SATA max UDMA/133 cmd0xEC00ctl0xE082bmdma0xD880irq 209
ata2: SATA max UDMA/133 cmd0xE000ctl0xDC02bmdma0xD888irq 209
ata1: SATA link up 1.5 Gbps (SStatus 113)
scsi0 :sata_uli
ata2: SATA link down (SStatus 0)
scsi1 :sata_uli
Quoted 4 lines
No disks are found, even though the link (on ata1) is detected.
Verified both with an x86 and an
x86_64kernel, and both 2.6.15-rc5 and 2.6.15-rc5-mm2.
I have exactly the same board and 2.6.15-rc5/x86-64 works for me (no problems with detecting SATA drives on SATA1 ports). The drives are jumper-forced to SATA1, though, and I haven't tried the SATA2 controller.
Greetings,
Rafael
Signature · 1 line
Beer is proof that God loves us and wants us to be happy - Benjamin Franklin