Skip to contentSkip to conversation

EDAC with sysfs interface added

PATCH In review Doug Thompson 2 participants 4 messages Dec 19, 2005 – Dec 20, 2005

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 EDAC with sysfs interface added

From: doug thompson <[email protected]>

Patch against 2.6.15-rc5-mm3

EDAC has been modifed to remove old interface and add new interface.

Removed /proc/mc and /proc/sys/mc from edac
Added /sys/devices/system/edac interface
Added 'mc' and 'pci' under 'edac'
Added Documentation/drivers/edac/edac.txt
Code cleaning in edac_mc.c

---
 Documentation/drivers/edac/edac.txt |  673 +++++++++++++
 MAINTAINERS                         |    9
 drivers/edac/edac_mc.c              | 1831 ++++++++++++++++++++++++++++--------
 drivers/edac/edac_mc.h              |   23
 4 files changed, 2166 insertions(+), 370 deletions(-)
Documentation/drivers/edac/edac.txt +673 -0
diff -uprN orig/Documentation/drivers/edac/edac.txt new/Documentation/drivers/edac/edac.txt
@@ -0,0 +1,673 @@
+
+
+EDAC - Error Detection And Correction
+
+Written by Doug Thompson <[email protected]>
+7 Dec 2005
+
+
+EDAC was written by:
+	Thayne Harbaugh, 
+	modified by Dave Peterson, Doug Thompson, et al, 
+	from the bluesmoke.sourceforge.net project.
+
+
+============================================================================
+EDAC PURPOSE
+
+The 'edac' kernel module goal is to detect and report errors that occur
+within the computer system. In the initial release, memory Correctable Errors
+(CE) and Uncorrectable Errors (UE) are the primary errors being harvested.
+
+Detecting CE events, then harvesting those events and reporting them, 
+CAN be a predictor of future UE events.  With CE events, the system can
+continue to operate, but with less safety. Preventive maintainence and
+proactive part replacement of memory DIMMs exhibiting CEs can reduce 
+the likelihood of the dreaded UE events and system 'panics'.
+
+
+In addition, PCI Bus Parity and SERR Errors are scanned for on PCI devices 
+in order to determine if errors are occurring on data transfers. 
+The presence of PCI Parity errors must be examined with a grain of salt. 
+There are several addin adapters that do NOT follow the PCI specification 
+with regards to Parity generation and reporting. The specification says 
+the vendor should tie the parity status bits to 0 if they do not intend 
+to generate parity.  Some vendors do not do this, and thus the parity bit 
+can "float" giving false positives.
+
+The PCI Parity EDAC device has the ability to "skip" known flakey 
+cards during the parity scan. These are set by the parity "blacklist"
+interface in the sysfs for PCI Parity. (See the PCI section in the sysfs
+section below.) There is also a parity "whitelist" which is used as 
+an explicit list of devices to scan, while the blacklist is a list 
+of devices to skip.
+
+EDAC will have future error detectors that will be added or integrated
+into EDAC in the following list:
+
+	MCE	Machine Check Exception
+	MCA	Machine Check Architecture
+	NMI	NMI notification of ECC errors
+	MSRs 	Machine Specific Register error cases
+	and other mechanisms. 
+
+These errors are usually bus errors, ECC errors, thermal throttling 
+and the like.
+
+
+============================================================================
+EDAC VERSIONING
+
+EDAC is composed of a "core" module (edac_mc.ko) and several Memory 
+Controller (MC) driver modules. On a given system, the CORE 
+is loaded and one MC driver will be loaded. Both the CORE and 
+the MC driver have individual versions that reflect current release 
+level of their respective modules.  Thus, to "report" on what version 
+a system is running, one must report both the CORE's and the 
+MC driver's versions.
+
+
+LOADING
+
+If 'edac' was statically linked with the kernel then no loading is
+necessary.  If 'edac' was built as modules then simply modprobe the
+'edac' pieces that you need.  You should be able to modprobe
+hardware-specific modules and have the dependencies load the necessary core
+modules.
+
+Example:
+
+$> modprobe amd76x_edac
+
+loads both the amd76x_edac.ko memory controller module and the edac_mc.ko
+core module.
+
+
+============================================================================
+EDAC sysfs INTERFACE
+
+EDAC presents a 'sysfs' interface for control, reporting and attribute
+reporting purposes.
+
+EDAC lives in the /sys/devices/system/edac directory. Within this directory
+there currently reside 2 'edac' components:
+
+	mc	memory controller(s) system
+	pci	PCI status system
+
+
+============================================================================
+Memory Controller (mc) Model
+
+First a background on the memory controller's model abstracted in EDAC.
+Each mc device controls a set of DIMM memory modules. These modules are
+layed out in a Chip-Select Row (csrowX) and Channel table (chX). There can
+be multiple csrows and two channels. 
+
+Memory controllers allow for several csrows, with 8 csrows being a typical value.
+Yet, the actual number of csrows depends on the electrical "loading"
+of a given motherboard, memory controller and DIMM characteristics.
+
+Dual channels allows for 128 bit data transfers to the CPU from memory.
+
+
+		Channel 0	Channel 1
+	===================================
+	csrow0	| DIMM_A0	| DIMM_B0 |
+	csrow1	| DIMM_A0	| DIMM_B0 |
+	===================================
+
+	===================================
+	csrow2	| DIMM_A1	| DIMM_B1 |
+	csrow3	| DIMM_A1	| DIMM_B1 |
+	===================================
+
+In the above example table there are 4 physical slots on the motherboard
+for memory DIMMs:
+
+	DIMM_A0
+	DIMM_B0
+	DIMM_A1
+	DIMM_B1
+
+Labels for these slots are usually silk screened on the motherboard. Slots
+labeled 'A' are channel 0 in this example. Slots labled 'B'
+are channel 1. Notice that there are two csrows possible on a 
+physical DIMM. These csrows are allocated their csrow assignment
+based on the slot into which the memory DIMM is placed. Thus, when 1 DIMM
+is placed in each Channel, the csrows cross both DIMMs.
+
+Memory DIMMs come single or dual "ranked". A rank is a populated csrow.
+Thus, 2 single ranked DIMMs, placed in slots DIMM_A0 and DIMM_B0 above 
+will have 1 csrow, csrow0. csrow1 will be empty. On the other hand,
+when 2 dual ranked DIMMs are similiaryly placed, then both csrow0 and
+csrow1 will be populated. The pattern repeats itself for csrow2 and
+csrow3.
+
+The representation of the above is reflected in the directory tree
+in EDAC's sysfs interface. Starting in directory 
+/sys/devices/system/edac/mc each memory controller will be represented 
+by its own 'mcX' directory, where 'X" is the index of the MC.
+
+
+	..../edac/mc/
+		   |
+		   |->mc0
+		   |->mc1
+		   |->mc2
+		   ....
+
+Under each 'mcX' directory each 'csrowX' is again represented by a
+'csrowX', where 'X" is the csrow index:
+
+
+	.../mc/mc0/
+		|
+		|->csrow0
+		|->csrow2
+		|->csrow3
+		....
+
+Notice that there is no csrow1, which indicates that csrow0 is
+composed of a single ranked DIMMs. This should also apply in both
+Channels, in order to have dual-channel mode be operational. Since
+both csrow2 and csrow3 are populated, this indicates a dual ranked
+set of DIMMs for channels 0 and 1.
+
+
+Within each of the 'mc','mcX' and 'csrowX' directories are several
+EDAC control and attribute files.
+
+
+============================================================================
+DIRECTORY 'mc'
+
+In directory 'mc' are EDAC system overall control and attribute files:
+
+
+Panic on UE control file:
+
+	'panic_on_ue'
+
+	An uncorrectable error will cause a machine panic.  This is usually
+	desirable.  It is a bad idea to continue when an uncorrectable error
+	occurs - it is indeterminate what was uncorrected and the operating
+	system context might be so mangled that continuing will lead to further
+	corruption. If the kernel has MCE configured, then EDAC will never
+	notice the UE.
+
+	LOAD TIME: module/kernel parameter: panic_on_ue=[0|1]
+	
+	RUN TIME:  echo "1" >/sys/devices/system/edac/mc/panic_on_ue
+
+
+Log UE control file:
+
+	'log_ue'
+
+	Generate kernel messages describing uncorrectable errors.  These errors
+	are reported through the system message log system.  UE statistics 
+	will be accumulated even when UE logging is disabled.
+	
+	LOAD TIME: module/kernel parameter: log_ue=[0|1]
+	
+	RUN TIME: echo "1" >/sys/devices/system/edac/mc/log_ue
+
+
+Log CE control file:
+
+	'log_ce'
+
+	Generate kernel messages describing correctable errors.  These 
+	errors are reported through the system message log system.  
+	CE statistics will be accumulated even when CE logging is disabled.
+
+	LOAD TIME: module/kernel parameter: log_ce=[0|1]
+
+	RUN TIME: echo "1" >/sys/devices/system/edac/mc/log_ce
+
+
+Polling period control file:
+
+	'poll_msec'
+
+	The time period, in milliseconds, for polling for error information.
+	Too small a value wastes resources.  Too large a value might delay
+	necessary handling of errors and might loose valuable information for
+	locating the error.  1000 milliseconds (once each second) is about
+	right for most uses.
+
+	LOAD TIME: module/kernel parameter: poll_msec=[0|1]
+
+	RUN TIME: echo "1000" >/sys/devices/system/edac/mc/poll_msec
+
+
+Module Version read-only attribute file:
+
+	'mc_version'
+
+	The EDAC CORE modules's version and compile date are shown here to
+	indicate what EDAC is running.
+
+
+
+============================================================================
+'mcX' DIRECTORIES 
+
+
+In 'mcX' directories are EDAC control and attribute files for
+this 'X" instance of the memory controllers:
+
+
+Counter reset control file:
+
+	'reset_counters'
+
+	This write-only control file will zero all the statistical counters 
+	for UE and CE errors.  Zeroing the counters will also reset the timer 
+	indicating how long since the last counter zero.  This is useful 
+	for computing errors/time.  Since the counters are always reset at 
+	driver initialization time, no module/kernel parameter is available.
+
+	RUN TIME: echo "anything" >/sys/devices/system/edac/mc/mc0/counter_reset
+
+		This resets the counters on memory controller 0
+
+
+Seconds since last counter reset control file:
+
+	'seconds_since_reset'
+
+	This attribute file displays how many seconds have elapsed since the
+	last counter reset. This can be used with the error counters to
+	measure error rates.
+
+
+
+DIMM capability attribute file:
+
+	'edac_capability'
+
+	The EDAC (Error Detection and Correction) capabilities/modes of
+	the memory controller hardware.
+
+
+DIMM Current Capability attribute file:
+
+	'edac_current_capability'
+
+	The EDAC capabilities available with the hardware
+	configuration.  This may not be the same as "EDAC capability"
+	if the correct memory is not used.  If a memory controller is
+	capable of EDAC, but DIMMs without check bits are in use, then
+	Parity, SECDED, S4ECD4ED capabilities will not be available
+	even though the memory controller might be capable of those
+	modes with the proper memory loaded.
+
+
+Memory Type supported on this controller attribute file:
+
+	'supported_mem_type'
+
+	This attribute file displays the memory type, usually 
+	buffered and unbuffered DIMMs.
+
+
+Memory Controller name attribute file:
+
+	'mc_name'
+
+	This attribute file displays the type of memory controller
+	that is being utilized.
+
+
+Memory Controller Module name attribute file:
+
+	'module_name'
+
+	This attribute file displays the memory controller module name, 
+	version and date built.  The name of the memory controller 
+	hardware - some drivers work with multiple controllers and 
+	this field shows which hardware is present.
+
+
+Total memory managed by this memory controller attribute file:
+
+	'size_mb'
+
+	This attribute file displays, in count of megabytes, of memory
+	that this instance of memory controller manages.
+
+
+Total Uncorrectable Errors count attribute file:
+
+	'ue_count'
+
+	This attribute file displays the total count of uncorrectable
+	errors that have occurred on this memory controller. If panic_on_ue 
+	is set this counter will not have a chance to increment, 
+	since EDAC will panic the system.
+
+
+Total UE count that had no information attribute fileY:
+
+	'ue_noinfo_count'
+
+	This attribute file displays the number of UEs that
+	have occurred have occurred with  no informations as to which DIMM 
+	slot is having errors.
+
+
+Total Correctable Errors count attribute file:
+
+	'ce_count'
+
+	This attribute file displays the total count of correctable
+	errors that have occurred on this memory controller. This
+	count is very important to examine. CEs provide early
+	indications that a DIMM is beginning to fail. This count
+	field should be monitored for non-zero values and report
+	such information to the system administrator.
+
+
+Total Correctable Errors count attribute file:
+
+	'ce_noinfo_count'
+
+	This attribute file displays the number of CEs that
+	have occurred wherewith no informations as to which DIMM slot
+	is having errors. Memory is handicapped, but operational, 
+	yet no information is available to indicate which slot
+	the failing memory is in. This count field should be also
+	be monitored for non-zero values.
+
+Device Symlink:
+
+	'device'
+
+	Symlink to the memory controller device
+
+
+
+============================================================================
+'csrowX' DIRECTORIES 
+
+In the 'csrowX' directories are EDAC control and attribute files for
+this 'X" instance of csrow:
+
+
+Total Uncorrectable Errors count attribute file:
+
+	'ue_count'
+
+	This attribute file displays the total count of uncorrectable
+	errors that have occurred on this csrow. If panic_on_ue is set
+	this counter will not have a chance to increment, since EDAC
+	will panic the system.
+
+
+Total Correctable Errors count attribute file:
+
+	'ce_count'
+
+	This attribute file displays the total count of correctable
+	errors that have occurred on this csrow. This
+	count is very important to examine. CEs provide early
+	indications that a DIMM is beginning to fail. This count
+	field should be monitored for non-zero values and report
+	such information to the system administrator.
+
+
+Total memory managed by this csrow attribute file:
+
+	'size_mb'
+
+	This attribute file displays, in count of megabytes, of memory
+	that this csrow contatins.
+
+
+Memory Type attribute file:
+
+	'mem_type'
+
+	This attribute file will display what type of memory is currently
+	on this csrow. Normally, either buffered or unbuffered memory.
+
+
+EDAC Mode of operation attribute file:
+
+	'edac_mode'
+
+	This attribute file will display what type of Error detection
+	and correction is being utilized.
+
+
+Device type attribute file:
+
+	'dev_type'
+
+	This attribute file will display what type of DIMM device is
+	being utilized. Example:  x4
+
+
+Channel 0 CE Count attribute file:
+
+	'ch0_ce_count'
+
+	This attribute file will display the count of CEs on this
+	DIMM located in channel 0.
+
+
+Channel 0 UE Count attribute file:
+
+	'ch0_ue_count'
+
+	This attribute file will display the count of UEs on this
+	DIMM located in channel 0.
+
+
+Channel 0 DIMM Label control file:
+
+	'ch0_dimm_label'
+
+	This control file allows this DIMM to have a label assigned 
+	to it. With this label in the module, when errors occur
+	the output can provide the DIMM label in the system log.
+	This becomes vital for panic events to isolate the
+	cause of the UE event.
+
+	DIMM Labels must be assigned after booting, with information
+	that correctly identifies the physical slot with its
+	silk screen label. This information is currently very
+	motherboard specific and determination of this information
+	must occur in userland at this time.
+
+
+Channel 1 CE Count attribute file:
+
+	'ch1_ce_count'
+
+	This attribute file will display the count of CEs on this
+	DIMM located in channel 1.
+
+
+Channel 1 UE Count attribute file:
+
+	'ch1_ue_count'
+
+	This attribute file will display the count of UEs on this
+	DIMM located in channel 0.
+
+
+Channel 1 DIMM Label control file:
+
+	'ch1_dimm_label'
+
+	This control file allows this DIMM to have a label assigned 
+	to it. With this label in the module, when errors occur
+	the output can provide the DIMM label in the system log.
+	This becomes vital for panic events to isolate the
+	cause of the UE event.
+
+	DIMM Labels must be assigned after booting, with information
+	that correctly identifies the physical slot with its
+	silk screen label. This information is currently very
+	motherboard specific and determination of this information
+	must occur in userland at this time.
+
+
+============================================================================
+SYSTEM LOGGING
+
+If logging for UEs and CEs are enabled then system logs will have
+error notices indicating errors that have been detected:
+
+MC0: CE page 0x283, offset 0xce0, grain 8, syndrome 0x6ec3, row 0,
+channel 1 "DIMM_B1": amd76x_edac
+
+MC0: CE page 0x1e5, offset 0xfb0, grain 8, syndrome 0xb741, row 0,
+channel 1 "DIMM_B1": amd76x_edac
+
+
+The structure of the message is:
+	the memory controller			(MC0)
+	Error type				(CE)
+	memory page				(0x283)
+	offset in the page			(0xce0)
+	the byte granularity 			(grain 8)
+		or resolution of the error
+	the error syndrome			(0xb741)
+	memory row				(row 0)
+	memory channel				(channel 1)
+	DIMM label, if set prior		(DIMM B1
+	and then an optional, driver-specific message that may 
+		have additional information.  
+
+Both UEs and CEs with no info will lack all but memory controller, 
+error type, a notice of "no info" and then an optional, 
+driver-specific error message.
+
+
+
+============================================================================
+PCI Bus Parity Detection
+
+
+On Header Type 00 devices the primary status is looked at
+for any parity error regardless of whether Parity is enabled on the
+device.  (The spec indicates parity is generated in some cases).
+On Header Type 01 bridges, the secondary status register is also
+looked at to see if parity ocurred on the bus on the other side of
+the bridge.
+
+
+SYSFS CONFIGURATION
+
+Under /sys/devices/system/edac/pci are control and attribute files as follows:
+
+
+Enable/Disable PCI Parity checking control file:
+
+	'check_pci_parity'
+
+
+	This control file enables or disables the PCI Bus Parity scanning
+	operation. Writing a 1 to this file enables the scanning. Writing 
+	a 0 to this file disables the scanning.
+
+	Enable:
+	echo "1" >/sys/devices/system/edac/pci/check_pci_parity
+
+	Disable:
+	echo "0" >/sys/devices/system/edac/pci/check_pci_parity
+
+
+
+Panic on PCI PARITY Error:
+
+	'panic_on_pci_parity'
+
+
+	This control files enables or disables panic'ing when a parity
+	error has been detected.
+
+
+	module/kernel parameter: panic_on_pci_parity=[0|1]
+
+	Enable:
+	echo "1" >/sys/devices/system/edac/pci/panic_on_pci_parity
+
+	Disable:
+	echo "0" >/sys/devices/system/edac/pci/panic_on_pci_parity
+
+
+Parity Count:
+
+	'pci_parity_count'
+
+	This attribute file will display the number of parity errors that
+	have been detected.
+
+
+
+PCI Device Whitelist:
+
+	'pci_parity_whitelist'
+
+	This control file allows for an explicit list of PCI devices to be
+	scanned for parity errors. Only devices found on this list will
+	be examined.  The list is a line of hexadecimel VENDOR and DEVICE
+	ID tuples:
+
+	1022:7450,1434:16a6
+
+	One or more can be inserted, seperated by a comma.
+
+	To write the above list doing the following as one command line:
+
+	echo "1022:7450,1434:16a6" 
+		> /sys/devices/system/edac/pci/pci_parity_whitelist
+
+
+
+	To display what the whitelist is, simply 'cat' the same file.
+
+
+PCI Device Blacklist:
+
+	'pci_parity_blacklist'
+
+	This control file allows for a list of PCI devices to be
+	skipped for scanning. 
+	The list is a line of hexadecimel VENDOR and DEVICE ID tuples:
+
+	1022:7450,1434:16a6
+
+	One or more can be inserted, seperated by a comma.
+
+	To write the above list doing the following as one command line:
+
+	echo "1022:7450,1434:16a6" 
+		> /sys/devices/system/edac/pci/pci_parity_blacklist
+
+
+	To display what the whitelist current contatins, 
+	simply 'cat' the same file.
+
+=======================================================================
+
+PCI Vendor and Devices IDs can be obtained with the lspci command. Using
+the -n option lspci will display the vendor and device IDs. The system
+adminstrator will have to determine which devices should be scanned or
+skipped.
+
+
+
+The two lists (white and black) are prioritized. blacklist is the lower 
+priority and will NOT be utilized when a whitelist has been set. 
+Turn OFF a whitelist by an empty echo command:
+
+	echo > /sys/devices/system/edac/pci/pci_parity_whitelist
+
+and any previous blacklist will be utililzed.
+
MAINTAINERS +9 -0
diff -uprN orig/MAINTAINERS new/MAINTAINERS
@@ -875,6 +875,15 @@ L:	[email protected]
 W:	http://ebtables.sourceforge.net/
 S:	Maintained
 
+EDAC-CORE
+P:      Doug Thompson
+M:      [email protected], [email protected]
+P:      Dave Peterson
+M:      [email protected], [email protected]
+L:      [email protected]
+W:      bluesmoke.sourceforge.net
+S:      Maintained
+
 EEPRO100 NETWORK DRIVER
 P:	Andrey V. Savochkin
 M:	[email protected]
drivers/edac/edac_mc.c +1466 -365

2,230 lines not on this page · raw message

drivers/edac/edac_mc.h +18 -5
diff -uprN orig/drivers/edac/edac_mc.h new/drivers/edac/edac_mc.h
@@ -31,9 +31,9 @@
 #include <linux/nmi.h>
 #include <linux/rcupdate.h>
 #include <linux/completion.h>
+#include <linux/kobject.h>
 
 
-#define	EDAC_MC_VER	"MC $Revision: 1.4.2.10 $"
 #define EDAC_MC_LABEL_LEN	31
 #define MC_PROC_NAME_MAX_LEN 7
 
@@ -51,11 +51,13 @@ do { if (level <= edac_debug_level) prin
 #define debugf1( ... ) edac_debug_printk(1, __VA_ARGS__ )
 #define debugf2( ... ) edac_debug_printk(2, __VA_ARGS__ )
 #define debugf3( ... ) edac_debug_printk(3, __VA_ARGS__ )
+#define debugf4( ... ) edac_debug_printk(4, __VA_ARGS__ )
 #else				/* !CONFIG_EDAC_DEBUG */
 #define debugf0( ... )
 #define debugf1( ... )
 #define debugf2( ... )
 #define debugf3( ... )
+#define debugf4( ... )
 #endif				/* !CONFIG_EDAC_DEBUG */
 
 
@@ -164,6 +166,10 @@ enum scrub_type {
 #define SCRUB_FLAG_HW_PROG_SRC	BIT(SCRUB_HW_PROG_SRC_CORR)
 #define SCRUB_FLAG_HW_TUN	BIT(SCRUB_HW_TUNABLE)
 
+enum mci_sysfs_status {
+	MCI_SYSFS_INACTIVE = 0,	/* sysfs entries NOT registered */
+	MCI_SYSFS_ACTIVE	/* sysfs entries ARE registered */
+};
 
 /* FIXME - should have notify capabilities: NMI, LOG, PROC, etc */
 
@@ -272,6 +278,9 @@ struct csrow_info {
 	enum mem_type mtype;	/* memory csrow type */
 	enum edac_type edac_mode;	/* EDAC mode for this csrow */
 	struct mem_ctl_info *mci;	/* the parent */
+
+	struct kobject kobj;	/* sysfs kobject for this csrow */
+
 	/* FIXME the number of CHANNELs might need to become dynamic */
 	u32 nr_channels;
 	struct channel_info *channels;
@@ -291,6 +300,9 @@ struct mem_ctl_info {
 				   edac_cap would not have that capability. */
 	unsigned long scrub_cap;	/* chipset scrub capabilities */
 	enum scrub_type scrub_mode;	/* current scrub mode */
+
+	enum mci_sysfs_status sysfs_active;	/* status of sysfs */
+
 	/* pointer to edac checking routine */
 	void (*edac_check) (struct mem_ctl_info * mci);
 	/*
@@ -325,9 +337,13 @@ struct mem_ctl_info {
 	 */
 	struct rcu_head rcu;
 	struct completion complete;
+	
+	/* edac sysfs device control */
+	struct kobject edac_mci_kobj;
 };
 
 
+
 /* write all or some bits in a byte-register*/
 static inline void pci_write_bits8(struct pci_dev *pdev, int offset,
 				   u8 value, u8 mask)
@@ -426,10 +442,7 @@ extern struct mem_ctl_info *edac_mc_allo
 		unsigned nr_csrows, unsigned nr_chans);
 
 /* Free an mc previously allocated by edac_mc_alloc() */
-static inline void edac_mc_free(struct mem_ctl_info *mci)
-{
-	kfree(mci);
-}
+extern void edac_mc_free(struct mem_ctl_info *mci);
 
 
 #endif				/* _EDAC_MC_H_ */

"If you think Education is expensive, just try Ignorance"

"Don't tell people HOW to do things, tell them WHAT you want and they will surprise you with their ingenuity."
Gen George Patton

#1 lore raw

-----BEGIN PGP SIGNED MESSAGE-----
Hash: RIPEMD160

Quoted 5 lines · Doug Thompson

From: doug thompson <[email protected]>

Patch against 2.6.15-rc5-mm3

EDAC has been modifed to remove old interface and add new interface.

hi Doug, i've seen you answering a problem i still have with 2.6.15-rc5-mm3:

http://www.uwsg.iu.edu/hypermail/linux/kernel/0512.0/0529.html

i just want to post a "me too" here along with lspci, because you inteded to add black/whitelists to this EDAC thingy, maybe it is of some help:

http://www.nerdbynature.de/bits/prinz64/2.6.15-rc5-mm3/

thanks,
Christian.
- --
BOFH excuse #60:

system has been recalled
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.2 (GNU/Linux)
Comment: Using GnuPG with Thunderbird - http://enigmail.mozdev.org

iD8DBQFDqBAw+A7rjkF8z0wRA6ofAJ9OvQcmb13KaPJFTxRkosfu8M1wHgCcCGPS dFsfclwLcKbaTa/vafldmSU=
=mVwM
-----END PGP SIGNATURE-----

#2 lore raw
Quoted 14 lines · --- Christian Kujau

-----BEGIN PGP SIGNED MESSAGE-----
Hash: RIPEMD160

Quoted 5 lines · Doug Thompson

From: doug thompson <[email protected]>

Patch against 2.6.15-rc5-mm3

EDAC has been modifed to remove old interface and add new interface.

hi Doug, i've seen you answering a problem i still have with 2.6.15-rc5-mm3:

http://www.uwsg.iu.edu/hypermail/linux/kernel/0512.0/0529.html

Quoted 8 lines

i just want to post a "me too" here along with lspci, because you inteded to add black/whitelists to this EDAC thingy, maybe it is of some help:

http://www.nerdbynature.de/bits/prinz64/2.6.15-rc5-mm3/

thanks,
Christian.
- --

You reminded me that I failed to put in the summary that whitelist/blacklist ARE in this patch as well as the sysfs. Apply the patch, and set your white or black list with the vendor_id:device_id that you desire. This needs to be done after bootup.

We plan on some userspace script for initializing EDAC, etc. But we need it in the kernel first. We will put such at bluesmoke.sourceforge.net

doug thompson

#3 lore raw

-----BEGIN PGP SIGNED MESSAGE-----
Hash: RIPEMD160

Quoted 3 lines · Doug Thompson

You reminded me that I failed to put in the summary that whitelist/blacklist ARE in this patch as well as the sysfs. Apply the patch, and set your white or black list with the vendor_id:device_id that you desire. This needs to be done after bootup.

will do, thanks!

Christian.
- --
BOFH excuse #45:

virus attack, luser responsible
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.2 (GNU/Linux)
Comment: Using GnuPG with Thunderbird - http://enigmail.mozdev.org

iD8DBQFDqD0D+A7rjkF8z0wRA2lRAJ4wmCbVIn6dIkLsvAfbrwEnX1ug6gCfdEwt AFoOtOZsfY0gFQrya9dUrvk=
=7rf7
-----END PGP SIGNATURE-----