Skip to contentSkip to conversation

Suggestion on flash init

U-Boot-Users Wang Jian 3 participants 11 messages Dec 25, 2005 – Jan 4, 2006

lore
Share & tools
lore

Wang Jian

author
#0 lore raw

Hi,

After reading many board/*/flash.c and writing customer board driver for one of my customer, I think the current flash interface can be improved.

I suggest adding a subdir $(TOPDIR)/include/flash/ and putting flash chip information here. When you use some kinds of flash chips, just include relevant header files.

If we go further, many information in $(TOPDIR)/include/flash.h can be put into these header files.

And, even flash operation (non-CFI) sample code can be put into $(TOPDIR)/contrib/flash/.

The following is an example of AMD Spansion S29AL016M chip.

--snip--
#ifndef _FLASH_S29AL016M_H_
#define _FLASH_S29AL016M_H_

#define FLASH_S29AL016M_T_SECTORS 35
#define FLASH_S29AL016M_B_SECTORS 35

#define FLASH_S29AL016M_T_SIZE 0x00200000
#define FLASH_S29AL016M_B_SIZE 0x00200000

int FLASH_S29AL016M_T_BYTE_SA[] = {
        0x000000, 0x010000, 0x020000, 0x030000,
        0x040000, 0x050000, 0x060000, 0x070000,
        0x080000, 0x090000, 0x0A0000, 0x0B0000,
        0x0C0000, 0x0D0000, 0x0E0000, 0x0F0000,
        0x100000, 0x110000, 0x120000, 0x130000,
        0x140000, 0x150000, 0x160000, 0x170000,
        0x180000, 0x190000, 0x1A0000, 0x1B0000,
        0x1C0000, 0x1D0000, 0x1E0000, 0x1F0000,
        0x1F8000, 0x1FA000, 0x1C0000
};
int FLASH_S29AL016M_T_WORD_SA[] = {
        0x000000, 0x008000, 0x010000, 0x018000,
        0x020000, 0x028000, 0x030000, 0x038000,
        0x040000, 0x048000, 0x050000, 0x058000,
        0x060000, 0x068000, 0x070000, 0x078000,
        0x080000, 0x088000, 0x090000, 0x098000,
        0x0A0000, 0x0A8000, 0x0B0000, 0x0B8000,
        0x0C0000, 0x0C8000, 0x0D0000, 0x0D8000,
        0x0E0000, 0x0E8000, 0x0F0000, 0x0F8000,
        0x0FC000, 0x0FD000, 0x0FE000
};
int FLASH_S29AL016M_B_BYTE_SA[] = {
        0x000000, 0x004000, 0x006000, 0x008000,
        0x010000, 0x020000, 0x030000, 0x040000,
        0x050000, 0x060000, 0x070000, 0x080000,
        0x090000, 0x0A0000, 0x0B0000, 0x0C0000,
        0x0D0000, 0x0E0000, 0x0F0000, 0x100000,
        0x110000, 0x120000, 0x130000, 0x140000,
        0x150000, 0x160000, 0x170000, 0x180000,
        0x190000, 0x1A0000, 0x1B0000, 0x1C0000,
        0x1D0000, 0x1E0000, 0x1F0000
};
int FLASH_S29AL016M_B_WORD_SA[] = {
        0x000000, 0x002000, 0x003000, 0x004000,
        0x008000, 0x010000, 0x018000, 0x020000,
        0x028000, 0x030000, 0x038000, 0x040000,
        0x048000, 0x050000, 0x058000, 0x060000,
        0x068000, 0x070000, 0x078000, 0x080000,
        0x088000, 0x090000, 0x098000, 0x0A0000,
        0x0A8000, 0x0B0000, 0x0B8000, 0x0C0000,
        0x0C8000, 0x0D0000, 0x0D8000, 0x0E0000,
        0x0E8000, 0x0F0000, 0x0F8000
};

#endif
--snip--

In flash_get_size()
--snip--

        switch (device) {
        case BYTEME(AMD_ID_S29AL016M_T):
                info->flash_id += FLASH_S29AL016M_T;
                info->sector_count = FLASH_S29AL016M_T_SECTORS;
                info->size = FLASH_S29AL016M_T_SIZE;
                break;

        case BYTEME(AMD_ID_S29AL016M_B):
                info->flash_id += FLASH_S29AL016M_B;
                info->sector_count = FLASH_S29AL016M_B_SECTORS;
                info->size = FLASH_S29AL016M_B_SIZE;
                break;

--snip--

In flash_get_offset()
--snip--

        switch (info->flash_id & FLASH_TYPEMASK) {
        case FLASH_S29AL016M_T:
                for (i = 0; i < info->sector_count; i++) {
                        info->start[i] = base + FLASH_S29AL016M_T_BYTE_SA[i];
                }
                break;
        case FLASH_S29AL016M_B:
                for (i = 0; i < info->sector_count; i++) {
                        info->start[i] = base + FLASH_S29AL016M_B_BYTE_SA[i];
                }
                break;

--snip--

Signature · 1 line
  lark
#1 lore raw
Quoted 3 lines · In message <[email protected]> you wrote:

After reading many board/*/flash.c and writing customer board driver for one of my customer, I think the current flash interface can be improved.

Did you have a look at the cfi_flash driver? This is supposed to replace the custom board/*/flash.c in most cses (i. e. whenever memory footprint requirements are not too limiting).

Quoted 3 lines

I suggest adding a subdir $(TOPDIR)/include/flash/ and putting flash chip information here. When you use some kinds of flash chips, just include relevant header files.

I think we should use the cfi_driver instead.

And BTW - a comment on the suggested code:

Quoted 2 lines

If we go further, many information in $(TOPDIR)/include/flash.h can be put into these header files.

...

Quoted 1 line

The following is an example of AMD Spansion S29AL016M chip.

...

Quoted 3 lines
int FLASH_S29AL016M_T_BYTE_SA[] = {
        0x000000, 0x010000, 0x020000, 0x030000,
        0x040000, 0x050000, 0x060000, 0x070000,

...

All-capital-names should be reserved for preprocessor variables. It is not acceptable to use these for other variables or function names. It is also not a good idea to have such initializations in a header file which might get included more than once.

Best regards,

Wolfgang Denk

Signature · 4 lines
Software Engineering:  Embedded and Realtime Systems,  Embedded Linux
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
Bradley's Bromide: If computers get too  powerful,  we  can  organize
them into a committee - that will do them in.
author
#2 lore raw

Hi Wolfgang Denk,

Quoted 8 lines · Wolfgang Denk
Quoted 3 lines · In message <[email protected]> you wrote:

After reading many board/*/flash.c and writing customer board driver for one of my customer, I think the current flash interface can be improved.

Did you have a look at the cfi_flash driver? This is supposed to replace the custom board/*/flash.c in most cses (i. e. whenever memory footprint requirements are not too limiting).

I have tested cfi_flash.c for a while. Unfortuanately, it fails for Spansion S29AL016M. The chip can be recognized, chip information is all correct, but the erase and write routines fail.

The symptom is erase and write routine complete and seem to succeed, but content remains unchanged.

The datasheet I download from Spansion (S29AL016M_00_A5_E.pdf) says:

? CFI (Common Flash Interface) compliant: allows host system to
identify and accommodate multiple flash devices

Carefully read cfi_flash.c and datasheet, I think S29AL016M doesn't support the cfi_flash.c's command sequence for erasing and writing.

Quoted 17 lines
Quoted 4 lines

I suggest adding a subdir $(TOPDIR)/include/flash/ and putting flash chip information here. When you use some kinds of flash chips, just include relevant header files.

I think we should use the cfi_driver instead.

And BTW - a comment on the suggested code:

Quoted 2 lines

If we go further, many information in $(TOPDIR)/include/flash.h can be put into these header files.

...

Quoted 1 line

The following is an example of AMD Spansion S29AL016M chip.

...

Quoted 3 lines
int FLASH_S29AL016M_T_BYTE_SA[] = {
        0x000000, 0x010000, 0x020000, 0x030000,
        0x040000, 0x050000, 0x060000, 0x070000,
Quoted 7 lines

...

All-capital-names should be reserved for preprocessor variables. It is not acceptable to use these for other variables or function names. It is also not a good idea to have such initializations in a header file which might get included more than once.

The code I give are JUST example, so uppper or lower case is not a problem in this sense.

I did worry about such initializations in header file, but given the fact that only flash.c will include it, I think it is not a real problem. And even it is included by multiple files, we can make these variables static. Or we can use better solution, but the idea itself is still reasonable.

Signature · 1 line
  lark
#3 lore raw
Quoted 4 lines · In message <[email protected]> you wrote:

I have tested cfi_flash.c for a while. Unfortuanately, it fails for Spansion S29AL016M. The chip can be recognized, chip information is all correct, but the erase and write routines fail.

Then please (lets) fix the problem instead of inventing the wheel again.

Quoted 2 lines

And even it is included by multiple files, we can make these variables static. Or we can use better solution, but the idea itself is still

That's even worse as it would silently create multiple copies of the same data - which is just a waste of precious memory.

Best regards,

Wolfgang Denk

Signature · 4 lines
Software Engineering:  Embedded and Realtime Systems,  Embedded Linux
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
It is dangerous to be sincere unless you are also stupid.
                                                - George Bernard Shaw
author
#4 lore raw

Hi Wolfgang Denk,

Quoted 7 lines · Wolfgang Denk
Quoted 4 lines · In message <[email protected]> you wrote:

I have tested cfi_flash.c for a while. Unfortuanately, it fails for Spansion S29AL016M. The chip can be recognized, chip information is all correct, but the erase and write routines fail.

Then please (lets) fix the problem instead of inventing the wheel again.

After a bad sleep, I read the manual again. This time, I find the cfi_flash.c DOES do as what manual says. I will set some debug information and find what happend. Stay tune.

Signature · 1 line
  lark
author
#5 lore raw

Hi Denk,

Me again.

In my situation, S29AL016M works in x8 mode, which has different command sequence from in x16 mode.

The following are from datasheet.

Providing
vu_char *addr = (vu_char *) info->start[sect];

x16 mode sector erase
addr[0x555] = 0xAA;
addr[0x2AA] = 0x55;
addr[0x555] = 0x80;
addr[0x555] = 0xAA;
addr[0x2AA] = 0x55;
addr[0x000] = 0x30;
udelay(50); // at least 50 us before polling for status

x16 mode program
addr[0x555] = 0xAA;
addr[0x2AA] = 0x55;
addr[0x555] = 0xA0;
addr[offset] = data;

x8 mode sector erase
addr[0xAAA] = 0xAA;
addr[0x555] = 0x55;
addr[0xAAA] = 0x80;
addr[0xAAA] = 0xAA;
addr[0x555] = 0x55;
addr[0x000] = 0x30;
udelay(50); // at least 50 us before polling for status

x8 mode program
addr[0xAAA] = 0xAA;
addr[0x555] = 0x55;
addr[0xAAA] = 0xA0;
addr[offset] = data;

I have little knowledge about other flash chips, so it is not easy for me to write clean patch for cfi_flash.c, although I want to.

Regards

Quoted 17 lines · Wang Jian

Hi Wolfgang Denk,

Quoted 7 lines · Wolfgang Denk
Quoted 4 lines · In message <[email protected]> you wrote:

I have tested cfi_flash.c for a while. Unfortuanately, it fails for Spansion S29AL016M. The chip can be recognized, chip information is all correct, but the erase and write routines fail.

Then please (lets) fix the problem instead of inventing the wheel again.

After a bad sleep, I read the manual again. This time, I find the cfi_flash.c DOES do as what manual says. I will set some debug information and find what happend. Stay tune.

Signature · 1 line
  lark
#6 lore raw
Quoted 3 lines · In message <[email protected]> you wrote:

In my situation, S29AL016M works in x8 mode, which has different command sequence from in x16 mode.

If you look closer it is not so different at all.

Quoted 7 lines

x16 mode sector erase
addr[0x555] = 0xAA;
addr[0x2AA] = 0x55;
addr[0x555] = 0x80;
addr[0x555] = 0xAA;
addr[0x2AA] = 0x55;
addr[0x000] = 0x30;

...

Quoted 7 lines

x8 mode sector erase
addr[0xAAA] = 0xAA;
addr[0x555] = 0x55;
addr[0xAAA] = 0x80;
addr[0xAAA] = 0xAA;
addr[0x555] = 0x55;
addr[0x000] = 0x30;

0x555 = 0xAAA >> 1
0x2AA = 0x555 >> 1

Quoted 2 lines

I have little knowledge about other flash chips, so it is not easy for me to write clean patch for cfi_flash.c, although I want to.

The code is actually the very same, just taking into account the different addressing mode.

Best regards,

Wolfgang Denk

Signature · 5 lines
Software Engineering:  Embedded and Realtime Systems,  Embedded Linux
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
Another Armenia, Belgium ... the weak innocents who always seem to be
located on a natural invasion route.
	-- Kirk, "Errand of Mercy", stardate 3198.4
author
#7 lore raw

Hi Wolfgang Denk,

Quoted 23 lines · Wolfgang Denk
Quoted 3 lines · In message <[email protected]> you wrote:

In my situation, S29AL016M works in x8 mode, which has different command sequence from in x16 mode.

If you look closer it is not so different at all.

Quoted 7 lines

x16 mode sector erase
addr[0x555] = 0xAA;
addr[0x2AA] = 0x55;
addr[0x555] = 0x80;
addr[0x555] = 0xAA;
addr[0x2AA] = 0x55;
addr[0x000] = 0x30;

...

Quoted 7 lines

x8 mode sector erase
addr[0xAAA] = 0xAA;
addr[0x555] = 0x55;
addr[0xAAA] = 0x80;
addr[0xAAA] = 0xAA;
addr[0x555] = 0x55;
addr[0x000] = 0x30;

Quoted 9 lines

0x555 = 0xAAA >> 1
0x2AA = 0x555 >> 1

Quoted 2 lines

I have little knowledge about other flash chips, so it is not easy for me to write clean patch for cfi_flash.c, although I want to.

The code is actually the very same, just taking into account the different addressing mode.

I am not sure if other kind of AMD flash chips use such x8/x16 command sequence. I am afraid that I will fix one thing and break other things.

Signature · 1 line
  lark
#8 lore raw
Quoted 3 lines · In message <[email protected]> you wrote:

I am not sure if other kind of AMD flash chips use such x8/x16 command sequence. I am afraid that I will fix one thing and break other things.

They all do. At least all I can remember.

Best regards,

Wolfgang Denk

Signature · 4 lines
Software Engineering:  Embedded and Realtime Systems,  Embedded Linux
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
Peace was the way.
	-- Kirk, "The City on the Edge of Forever", stardate unknown
#9 lore raw
In reply to Wang Jian
Quoted 12 lines · Wang Jian

Hi Wolfgang Denk,

Quoted 6 lines · Wolfgang Denk
Quoted 3 lines · In message <[email protected]> you wrote:

I have tested cfi_flash.c for a while. Unfortuanately, it fails for Spansion S29AL016M. The chip can be recognized, chip information is all correct, but the erase and write routines fail.

Quoted 9 lines
Quoted 1 line

Then please (lets) fix the problem instead of inventing the wheel again.

After a bad sleep, I read the manual again. This time, I find the cfi_flash.c DOES do as what manual says. I will set some debug information and find what happend. Stay tune.

You might want to check list archives regarding cfi_flash.c and the a number of patches that are created over the past year that is *still* pending to be incorporated to the mainline.

And if you check the mailing list archives you might find that Spansion chip (most probably) auto locks all sectors when powered up so you will need to issue unlock sequence before write/erase can succeed. There has been some spirited discussions on this and Wolfgang as a U-Boot project leader had explained the way he wants the issue addressed.

Wolfgang, when can we expect the pull-up of patches on the cfi_flash.c driver? I am personally holding up for existing patches to go through before I work on new patches.

Best regards,
Tolunay

#10 lore raw

Dear Tolunay,

Quoted 3 lines · in message <[email protected]> you wrote:

Wolfgang, when can we expect the pull-up of patches on the cfi_flash.c driver? I am personally holding up for existing patches to go through

Well, in the last two months most of my time has been sucked up by the (long delayed) release of ELDK 4.0 (and by a little Xmas vacation :-).

Keep your finger's crossed, and tonight's ELDK build might be what we'll release as 4.0; the files in the CVS have already been tagged as 4.0. If no new problems show up, this should enable me to spend some more time on U-Boot again.

Quoted 1 line

before I work on new patches.

Ummm... if you use git, you can and should make yourself independent of my patch backlog. Actually if you spend the effort to go though the list of cfi_flash driver related patches and come up with a (somewhat tested) summary patch (or branch) that would be a great help. We could do the same like with the NAND code: add it as #testing-CFI branch, and if nobody complains I will merge it a little later.

*All* feedback I receive for patches (like messages saying "added patches X, Y, and Z, works for me, here ... is the URL of my git repo where you can pull from) is welcome and helps to accelerate things.

Best regards,

Wolfgang Denk

Signature · 3 lines
Software Engineering:  Embedded and Realtime Systems,  Embedded Linux
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
The existence of god implies a violation of causality.