Suppress APIC errors on UP x86-64.
Quite a few UP x86-64 laptops print APIC error 40's repeatedly when they run an SMP kernel (And Fedora doesn't ship a UP x86-64 kernel any more). We can suppress this as there's not really anything we can do about them.
arch/x86_64/kernel/apic.c renamed from arch/x86_64/kernel/apic.c~ +2 -1
@@ -1032,7 +1032,8 @@ asmlinkage void smp_error_interrupt(void6: Received illegal vector 7: Illegal register address */ -printk (KERN_DEBUG "APIC error on CPU%d: %02x(%02x)\n" , +if (num_online_cpus () >1 ) +printk (KERN_DEBUG "APIC error on CPU%d: %02x(%02x)\n" ,smp_processor_id (), v , v1);irq_exit (); }
Quoted 4 lines · Dave Jones
Quite a few UP x86-64 laptops print APIC error 40's repeatedly when they run an SMP kernel (And Fedora doesn't ship a UP x86-64 kernel any more). We can suppress this as there's not really anything we can do about them.
No we need to fix the APIC errors, not hide them.
-Andi
Quoted 16 lines
Signed-off-by Dave Jones <[email protected]>arch/x86_64/kernel/apic.c renamed from arch/x86_64/kernel/apic.c~ +2
-1@@ -1032,7 +1032,8 @@ asmlinkage void smp_error_interrupt(void6: Received illegal vector 7: Illegal register address */ -printk (KERN_DEBUG "APIC error on CPU%d: %02x(%02x)\n" , +if (num_online_cpus () >1 ) +printk (KERN_DEBUG "APIC error on CPU%d: %02x(%02x)\n" ,smp_processor_id (), v , v1);irq_exit (); }
Quoted 7 lines · Andi Kleen
Quoted 4 lines · Dave Jones
Quite a few UP x86-64 laptops print APIC error 40's repeatedly when they run an SMP kernel (And Fedora doesn't ship a UP x86-64 kernel any more). We can suppress this as there's not really anything we can do about them.
No we need to fix the APIC errors, not hide them.
What do you need to fix them ? I've got one laptop here that is affected, and there's a few other examples with dmesg's in Red Hat bugzilla that I can trawl.
Dave
Quoted 7 lines · Dave Jones
Quoted 6 lines · Andi Kleen
Quoted 4 lines · Dave Jones
Quite a few UP x86-64 laptops print APIC error 40's repeatedly when they run an SMP kernel (And Fedora doesn't ship a UP x86-64 kernel any more). We can suppress this as there's not really anything we can do about them.
Quoted 5 lines
Quoted 1 line
No we need to fix the APIC errors, not hide them.
What do you need to fix them ? I've got one laptop here that is affected, and there's a few other examples with dmesg's in Red Hat bugzilla that I can trawl.
Some pattern analysis would be useful. All the same chipset, revision?
Best you collect boot logs.
-Andi
Quoted 10 lines · Andi Kleen
Quoted 9 lines · Dave Jones
Quoted 7 lines · Andi Kleen
Quoted 4 lines · Dave Jones
Quite a few UP x86-64 laptops print APIC error 40's repeatedly when they run an SMP kernel (And Fedora doesn't ship a UP x86-64 kernel any more). We can suppress this as there's not really anything we can do about them.
No we need to fix the APIC errors, not hide them.
Quoted 7 lines
Quoted 3 lines
What do you need to fix them ? I've got one laptop here that is affected, and there's a few other examples with dmesg's in Red Hat bugzilla that I can trawl.
Some pattern analysis would be useful. All the same chipset, revision?
From first impression, it seems they're all (including mine) HP laptops
with ATI chipsets.
A quick google seems to confirm this.
http://www.google.com/search?&q=HP+%22apic+error%22
I wonder if this is related at all to the 'time goes double speed' bug that some folks see (incidentally, I don't on mine).
Quoted 1 line
Best you collect boot logs.
I'll try to gather some more data.
Dave
Quoted 2 lines · Dave Jones
From first impression, it seems they're all (including mine) HP laptops with ATI chipsets.
Ah that chipset from hell.
Quoted 3 lines
I wonder if this is related at all to the 'time goes double speed' bug that some folks see (incidentally, I don't on mine).
Very likely is.
-Andi
Quoted 7 lines
Quoted 4 lines · Dave Jones
Some pattern analysis would be useful. All the same chipset, revision?
From first impression, it seems they're all (including mine) HP laptops with ATI chipsets.
I have an HP _desktop_ with an ATI chipset and a dual-core 3800+ that exhibits this. If your patch just inhibits output for machines with one logical CPU, it won't be inhibiting it on mine. I'm seeing:
powernow-k8: error - out of sync, fix 0xa 0x2, vid 0xa 0x12
APIC error on CPU0: 00(40) # once, at boot
APIC error on CPU0: 40(40) # repeated regularly after boot
Quoted 2 lines
I wonder if this is related at all to the 'time goes double speed' bug that some folks see (incidentally, I don't on mine).
Yes, my machine exhibited this bug in earlier 2.6 releases. Passing enable_timer_pin_1 fixed it for me before the chipset detection was brought into mainline. Now that it's fixed, I still see the errors above; while both problems are caused by ATI's bizarre chipset, the error doesn't mean that double time is happening.
Quoted 3 lines
Quoted 1 line
Best you collect boot logs.
I'll try to gather some more data.
My dmesg and lspci are attached, let me know if you'd like anything else. The machine's an HP Pavilion A1250N.
Linux havoc 2.6.15-16-k7 #1 SMP PREEMPT Mon Feb 20 18:14:55 UTC 2006 i686 GNU/Linux
(Top of boot is missing from dmesg and /var/log/dmesg.)
[4294670.669000] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 *10 11) [4294670.669000] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 *4 5 6 7 10 11) [4294670.669000] ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 6 7 10 *11), disabled. [4294670.670000] ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 10 11) *0, disabled. [4294670.670000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT] [4294670.672000] Linux Plug and Play Support v0.97 (c) Adam Belay [4294670.672000] pnp: PnP ACPI init [4294670.672000] pnp: PnPACPI: unknown resource type 7 [4294670.672000] pnp: PnPACPI: METHOD_NAME__CRS failure for PNP0c02 [4294670.673000] pnp: PnPACPI: unknown resource type 7 [4294670.673000] pnp: PnPACPI: METHOD_NAME__CRS failure for PNP0200 [4294670.673000] pnp: PnPACPI: unknown resource type 7 [4294670.673000] pnp: PnPACPI: METHOD_NAME__CRS failure for PNP0b00 [4294670.673000] pnp: PnPACPI: unknown resource type 7 [4294670.673000] pnp: PnPACPI: METHOD_NAME__CRS failure for PNP0800 [4294670.673000] pnp: PnPACPI: unknown resource type 7 [4294670.673000] pnp: PnPACPI: METHOD_NAME__CRS failure for PNP0c04 [4294670.673000] pnp: PnPACPI: unknown resource type 7 [4294670.673000] pnp: PnPACPI: METHOD_NAME__CRS failure for PNP0c02 [4294670.674000] pnp: PnPACPI: unknown resource type 7 [4294670.674000] pnp: PnPACPI: METHOD_NAME__CRS failure for PNP0401 [4294670.674000] pnp: PnPACPI: unknown resource type 7 [4294670.674000] pnp: PnPACPI: METHOD_NAME__CRS failure for PNP0f13 [4294670.674000] pnp: PnPACPI: unknown resource type 7 [4294670.674000] pnp: PnPACPI: METHOD_NAME__CRS failure for PNP0303 [4294670.674000] pnp: PnPACPI: unknown resource type 7 [4294670.674000] pnp: PnPACPI: METHOD_NAME__CRS failure for PNP0c02 [4294670.674000] pnp: PnPACPI: unknown resource type 7 [4294670.674000] pnp: PnPACPI: METHOD_NAME__CRS failure for PNP0c01 [4294670.674000] pnp: PnP ACPI: found 0 devices [4294670.674000] PnPBIOS: Disabled by ACPI PNP [4294670.674000] PCI: Using ACPI for IRQ routing [4294670.674000] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report [4294670.674000] PCI: Cannot allocate resource region 3 of device 0000:00:00.0 [4294670.732000] PCI: Bridge: 0000:00:02.0 [4294670.732000] IO window: e000-efff [4294670.732000] MEM window: fa000000-fcffffff [4294670.732000] PREFETCH window: d0000000-dfffffff [4294670.732000] PCI: Bridge: 0000:00:14.4 [4294670.732000] IO window: d000-dfff [4294670.732000] MEM window: fde00000-fdefffff [4294670.732000] PREFETCH window: fdd00000-fddfffff [4294670.732000] PCI: Setting latency timer of device 0000:00:02.0 to 64 [4294670.732000] audit: initializing netlink socket (disabled) [4294670.732000] audit(1140818198.730:1): initialized [4294670.732000] VFS: Disk quotas dquot_6.5.1 [4294670.732000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [4294670.732000] Initializing Cryptographic API [4294670.732000] io scheduler noop registered [4294670.732000] io scheduler anticipatory registered [4294670.732000] io scheduler deadline registered [4294670.732000] io scheduler cfq registered [4294670.782000] PCI: Setting latency timer of device 0000:00:02.0 to 64 [4294670.782000] pcie_portdrv_probe->Dev[5a34:1002] has invalid IRQ. Check vendor BIOS [4294670.782000] assign_interrupt_mode Found MSI capability [4294670.782000] Allocate Port Service[pcie00] [4294670.782000] Allocate Port Service[pcie01] [4294670.782000] Allocate Port Service[pcie03] [4294670.782000] isapnp: Scanning for PnP cards... [4294671.139000] isapnp: No Plug & Play device found [4294671.158000] PNP: No PS/2 controller found. Probing ports directly. [4294671.161000] serio: i8042 AUX port at 0x60,0x64 irq 12 [4294671.161000] serio: i8042 KBD port at 0x60,0x64 irq 1 [4294671.161000] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled [4294671.162000] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize [4294671.162000] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 [4294671.162000] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx [4294671.162000] ACPI: bus type ide registered [4294671.162000] mice: PS/2 mouse device common for all mice [4294671.162000] EISA: Probing bus 0 at eisa.0 [4294671.162000] Cannot allocate resource for EISA slot 4 [4294671.162000] EISA: Detected 0 cards. [4294671.162000] NET: Registered protocol family 2 [4294671.173000] IP route cache hash table entries: 32768 (order: 5, 131072 bytes) [4294671.173000] TCP established hash table entries: 131072 (order: 8, 1572864 bytes) [4294671.174000] TCP bind hash table entries: 65536 (order: 7, 786432 bytes) [4294671.174000] TCP: Hash tables configured (established 131072 bind 65536) [4294671.174000] TCP reno registered [4294671.175000] TCP bic registered [4294671.175000] NET: Registered protocol family 1 [4294671.175000] NET: Registered protocol family 8 [4294671.175000] NET: Registered protocol family 20 [4294671.175000] Starting balanced_irq [4294671.175000] Using IPI No-Shortcut mode [4294671.175000] ACPI wakeup devices: [4294671.175000] PCI0 USB0 USB1 USB2 AUDO P2P MAC [4294671.175000] ACPI: (supports S0 S1 S3 S4 S5) [4294671.175000] Freeing unused kernel memory: 300k freed [4294671.196000] input: AT Translated Set 2 keyboard as /class/input/input0 [4294671.231000] vesafb: framebuffer at 0xd0000000, mapped to 0xc0880000, using 10240k, total 262144k [4294671.231000] vesafb: mode is 1280x1024x32, linelength=5120, pages=0 [4294671.231000] vesafb: protected mode interface info at c000:d4f0 [4294671.231000] vesafb: scrolling: redraw [4294671.231000] vesafb: Truecolor: size=8:8:8:8, shift=24:16:8:0 [4294671.231000] vesafb: Mode is VGA compatible [4294671.510000] Console: switching to colour frame buffer device 160x64 [4294671.510000] fb0: VESA VGA frame buffer device [4294672.528000] Capability LSM initialized [4294672.573000] ACPI: Processor [CPU0] (supports 8 throttling states) [4294672.573000] ACPI: Processor [CPU1] (supports 8 throttling states) [4294672.871000] SCSI subsystem initialized [4294672.872000] libata version 1.20 loaded. [4294672.873000] sata_sil 0000:00:12.0: version 0.9 [4294672.873000] ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 22 (level, low) -> IRQ 193 [4294672.873000] ata1: SATA max UDMA/100 cmd 0xC0846080 ctl 0xC084608A bmdma 0xC0846000 irq 193 [4294672.873000] ata2: SATA max UDMA/100 cmd 0xC08460C0 ctl 0xC08460CA bmdma 0xC0846008 irq 193 [4294673.229000] ata1: dev 0 cfg 49:2f00 82:3069 83:7f69 84:4163 85:3069 86:3e01 87:4063 88:203f [4294673.229000] ata1: dev 0 ATA-7, max UDMA/100, 488397168 sectors: LBA48 [4294673.229000] ata1: dev 0 configured for UDMA/100 [4294673.229000] scsi0 : sata_sil [4294673.430000] ata2: no device found (phy stat 00000000) [4294673.430000] scsi1 : sata_sil [4294673.430000] Vendor: ATA Model: HDT722525DLA380 Rev: V44O [4294673.430000] Type: Direct-Access ANSI SCSI revision: 05 [4294673.437000] SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB) [4294673.437000] SCSI device sda: drive cache: write back [4294673.437000] SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB) [4294673.437000] SCSI device sda: drive cache: write back [4294673.437000] sda: sda1 sda2 sda3 sda4 < sda5 sda6 > [4294673.474000] sd 0:0:0:0: Attached scsi disk sda [4294673.760000] ATIIXP: IDE controller at PCI slot 0000:00:14.1 [4294673.760000] ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 201 [4294673.760000] ATIIXP: chipset revision 0 [4294673.760000] ATIIXP: not 100% native mode: will probe irqs later [4294673.760000] ide0: BM-DMA at 0xf800-0xf807, BIOS settings: hda:pio, hdb:pio [4294673.760000] ide1: BM-DMA at 0xf808-0xf80f, BIOS settings: hdc:pio, hdd:pio [4294673.760000] Probing IDE interface ide0... [4294674.279000] Probing IDE interface ide1... [4294674.951000] hdc: HP DVD Writer 740b, ATAPI CD/DVD-ROM drive [4294675.666000] hdd: IDE-DVD DROM6216, ATAPI CD/DVD-ROM drive [4294675.719000] ide1 at 0x170-0x177,0x376 on irq 15 [4294675.728000] hdc: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33) [4294675.728000] Uniform CD-ROM driver Revision: 3.20 [4294675.732000] hdd: ATAPI 40X DVD-ROM drive, 512kB Cache, UDMA(33) [4294675.738000] Probing IDE interface ide0... [4294676.337000] usbcore: registered new driver usbfs [4294676.337000] usbcore: registered new driver hub [4294676.338000] ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) [4294676.338000] ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 19 (level, low) -> IRQ 209 [4294676.338000] ohci_hcd 0000:00:13.0: OHCI Host Controller [4294676.338000] ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 1 [4294676.338000] ohci_hcd 0000:00:13.0: irq 209, io mem 0xfe02e000 [4294676.393000] hub 1-0:1.0: USB hub found [4294676.393000] hub 1-0:1.0: 4 ports detected [4294676.494000] ACPI: PCI Interrupt 0000:00:13.1[A] -> GSI 19 (level, low) -> IRQ 209 [4294676.494000] ohci_hcd 0000:00:13.1: OHCI Host Controller [4294676.494000] ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 2 [4294676.494000] ohci_hcd 0000:00:13.1: irq 209, io mem 0xfe02d000 [4294676.549000] hub 2-0:1.0: USB hub found [4294676.549000] hub 2-0:1.0: 4 ports detected [4294676.650000] ACPI: PCI Interrupt 0000:00:13.2[A] -> GSI 19 (level, low) -> IRQ 209 [4294676.650000] ehci_hcd 0000:00:13.2: EHCI Host Controller [4294676.651000] ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 3 [4294676.651000] ehci_hcd 0000:00:13.2: irq 209, io mem 0xfe02c000 [4294676.651000] ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [4294676.651000] hub 3-0:1.0: USB hub found [4294676.651000] hub 3-0:1.0: 8 ports detected [4294676.839000] Attempting manual resume [4294676.873000] EXT3-fs: mounted filesystem with ordered data mode. [4294676.873000] kjournald starting. Commit interval 5 seconds [4294677.654000] usb 1-2: new full speed USB device using ohci_hcd and address 3 [4294678.011000] usb 2-2: new full speed USB device using ohci_hcd and address 2 [4294679.082000] sd 0:0:0:0: Attached scsi generic sg0 type 0 [4294679.234000] usb 2-4: new full speed USB device using ohci_hcd and address 3 [4294679.730000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [4294679.733000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 [4294679.841000] Linux agpgart interface v0.101 (c) Dave Jones [4294679.922000] ieee1394: Initialized config rom entry `ip1394' [4294679.932000] ohci1394: $Rev: 1313 $ Ben Collins <[email protected]> [4294679.932000] ACPI: PCI Interrupt 0000:02:04.0[A] -> GSI 21 (level, low) -> IRQ 169 [4294679.932000] PCI: Via IRQ fixup for 0000:02:04.0, from 255 to 9 [4294679.964000] 8139too Fast Ethernet driver 0.9.27 [4294679.964000] ACPI: PCI Interrupt 0000:02:03.0[A] -> GSI 20 (level, low) -> IRQ 217 [4294679.965000] eth0: RealTek RTL8139 at 0xc1388000, 00:13:d3:4e:5c:b6, IRQ 217 [4294679.965000] eth0: Identified 8139 chip type 'RTL-8100B/8139D' [4294680.032000] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[169] MMIO=[fdefd000-fdefd7ff] Max Packet=[2048] [4294680.051000] 8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004) [4294680.217000] ACPI: PCI Interrupt 0000:00:14.5[B] -> GSI 17 (level, low) -> IRQ 225 [4294680.275000] logips2pp: Detected unknown logitech mouse model 0 [4294680.311000] Bluetooth: Core ver 2.8 [4294680.311000] NET: Registered protocol family 31 [4294680.311000] Bluetooth: HCI device and connection manager initialized [4294680.311000] Bluetooth: HCI socket layer initialized [4294680.348000] input: ImPS/2 Logitech Wheel Mouse as /class/input/input1 [4294680.392000] ts: Compaq touchscreen protocol output [4294680.417000] Bluetooth: HCI USB driver ver 2.9 [4294680.418000] usbcore: registered new driver hci_usb [4294680.438000] usbcore: registered new driver hiddev [4294680.467000] Initializing USB Mass Storage driver... [4294680.492000] eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 [4294680.517000] NET: Registered protocol family 17 [4294680.646000] input: FingerWorks TouchStream ST/LP as /class/input/input2 [4294680.646000] input: USB HID v1.11 Keyboard [FingerWorks TouchStream ST/LP ] on usb-0000:00:13.1-2 [4294680.819000] input: FingerWorks TouchStream ST/LP as /class/input/input3 [4294680.819000] input: USB HID v1.11 Mouse [FingerWorks TouchStream ST/LP ] on usb-0000:00:13.1-2 [4294681.032000] input: FingerWorks TouchStream ST/LP as /class/input/input4 [4294681.032000] input: USB HID v1.11 Device [FingerWorks TouchStream ST/LP ] on usb-0000:00:13.1-2 [4294681.296000] ieee1394: Host added: ID:BUS[0-00:1023] GUID[0010dc0000b3a0f0] [4294681.338000] input: FingerWorks TouchStream ST/LP as /class/input/input5 [4294681.338000] input: USB HID v1.11 Multi-Axis Controller [FingerWorks TouchStream ST/LP ] on usb-0000:00:13.1-2 [4294681.338000] usbcore: registered new driver usbhid [4294681.338000] drivers/usb/input/hid-core.c: v2.6:USB HID core driver [4294681.338000] scsi2 : SCSI emulation for USB Mass Storage devices [4294681.338000] usb-storage: device found at 3 [4294681.338000] usb-storage: waiting for device to settle before scanning [4294681.338000] usbcore: registered new driver usb-storage [4294681.338000] USB Mass Storage support registered. [4294681.657000] parport0: PC-style at 0x378 [PCSPP,EPP] [4294681.689000] parport0: Printer, HEWLETT-PACKARD DESKJET 950C [4294681.692000] lp0: using parport0 (polling). [4294681.713000] sbp2: $Rev: 1306 $ Ben Collins <[email protected]> [4294681.713000] ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1) [4294681.713000] ieee1394: sbp2: Try serialize_io=0 for better performance [4294681.839000] Adding 2811332k swap on /dev/sda5. Priority:-1 extents:1 across:2811332k [4294681.950000] EXT3 FS on sda3, internal journal [4294682.099000] md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27 [4294682.099000] md: bitmap version 4.39 [4294682.555000] device-mapper: 4.4.0-ioctl (2005-01-12) initialised: [email protected] [4294682.764000] cdrom: open failed. [4294683.185000] cdrom: open failed. [4294683.189000] cdrom: open failed. [4294684.173000] NTFS driver 2.1.25 [Flags: R/O MODULE]. [4294684.215000] NTFS volume version 3.1. [4294684.234000] kjournald starting. Commit interval 5 seconds [4294684.234000] EXT3 FS on sda6, internal journal [4294684.234000] EXT3-fs: mounted filesystem with ordered data mode. [4294686.344000] Vendor: Generic Model: USB SD Reader Rev: 1.00 [4294686.344000] Type: Direct-Access ANSI SCSI revision: 00 [4294686.374000] sd 2:0:0:0: Attached scsi removable disk sdb [4294686.375000] sd 2:0:0:0: Attached scsi generic sg1 type 0 [4294686.380000] Vendor: Generic Model: USB CF Reader Rev: 1.01 [4294686.380000] Type: Direct-Access ANSI SCSI revision: 00 [4294686.411000] sd 2:0:0:1: Attached scsi removable disk sdc [4294686.411000] sd 2:0:0:1: Attached scsi generic sg2 type 0 [4294686.416000] Vendor: Generic Model: USB SM Reader Rev: 1.02 [4294686.416000] Type: Direct-Access ANSI SCSI revision: 00 [4294686.447000] sd 2:0:0:2: Attached scsi removable disk sdd [4294686.447000] sd 2:0:0:2: Attached scsi generic sg3 type 0 [4294686.453000] Vendor: Generic Model: USB MS Reader Rev: 1.03 [4294686.453000] Type: Direct-Access ANSI SCSI revision: 00 [4294686.483000] sd 2:0:0:3: Attached scsi removable disk sde [4294686.483000] sd 2:0:0:3: Attached scsi generic sg4 type 0 [4294686.483000] usb-storage: device scan complete [4294687.553000] ACPI: Power Button (FF) [PWRF] [4294687.553000] ACPI: Power Button (CM) [PWRB] [4294687.601000] NET: Registered protocol family 10 [4294687.601000] lo: Disabled Privacy Extensions [4294687.601000] IPv6 over IPv4 tunneling driver [4294687.671000] ibm_acpi: ec object not found [4294695.248000] apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac) [4294695.248000] apm: disabled - APM is not SMP safe. [4294697.350000] hdc: drive_cmd: status=0x51 { DriveReady SeekComplete Error } [4294697.350000] hdc: drive_cmd: error=0x04 { AbortedCommand } [4294697.350000] ide: failed opcode was: 0xec [4294697.358000] hdd: drive_cmd: status=0x51 { DriveReady SeekComplete Error } [4294697.358000] hdd: drive_cmd: error=0x04 { AbortedCommand } [4294697.358000] ide: failed opcode was: 0xec [4294697.926000] eth0: no IPv6 routers present [4294697.975000] hdc: drive_cmd: status=0x51 { DriveReady SeekComplete Error } [4294697.975000] hdc: drive_cmd: error=0x04 { AbortedCommand } [4294697.975000] ide: failed opcode was: 0xec [4294697.984000] hdd: drive_cmd: status=0x51 { DriveReady SeekComplete Error } [4294697.984000] hdd: drive_cmd: error=0x04 { AbortedCommand } [4294697.984000] ide: failed opcode was: 0xec [4294699.110000] powernow-k8: Found 2 AMD Athlon 64 / Opteron processors (version 1.50.4) [4294699.111000] powernow-k8: 0 : fid 0xc (2000 MHz), vid 0x8 (1350 mV) [4294699.111000] powernow-k8: 1 : fid 0xa (1800 MHz), vid 0xa (1300 mV) [4294699.111000] powernow-k8: 2 : fid 0x2 (1000 MHz), vid 0x12 (1100 mV) [4294699.111000] cpu_init done, current fid 0xc, vid 0x8 [4294699.113000] powernow-k8: 0 : fid 0xc (2000 MHz), vid 0x8 (1350 mV) [4294699.113000] powernow-k8: 1 : fid 0xa (1800 MHz), vid 0xa (1300 mV) [4294699.113000] powernow-k8: 2 : fid 0x2 (1000 MHz), vid 0x12 (1100 mV) [4294699.113000] cpu_init done, current fid 0xc, vid 0x8 [4294699.470000] Bluetooth: L2CAP ver 2.8 [4294699.470000] Bluetooth: L2CAP socket layer initialized [4294699.472000] Bluetooth: RFCOMM socket layer initialized [4294699.472000] Bluetooth: RFCOMM TTY layer initialized [4294699.472000] Bluetooth: RFCOMM ver 1.6 [4294701.141000] powernow-k8: error - out of sync, fix 0xc 0xa, vid 0x8 0xa [4294702.144000] powernow-k8: error - out of sync, fix 0xa 0x2, vid 0xa 0x12 [4294831.387000] APIC error on CPU0: 00(40) [4294929.542000] APIC error on CPU0: 40(40) [4294982.042000] APIC error on CPU0: 40(40) [4295159.225000] APIC error on CPU0: 40(40) [4295192.036000] APIC error on CPU0: 40(40) [4295205.160000] APIC error on CPU0: 40(40) [4295290.471000] APIC error on CPU0: 40(40) [4295312.125000] APIC error on CPU0: 40(40) [4295362.658000] APIC error on CPU0: 40(40) [4295454.531000] APIC error on CPU0: 40(40)
0000:00:00.0 Host bridge: ATI Technologies Inc RS480 Host Bridge (rev 10)
Subsystem: Hewlett-Packard Company: Unknown device 2a24
Flags: bus master, 66MHz, medium devsel, latency 64 I/O ports at 4100 [disabled] [size=32]
Memory at <ignored> (64-bit, non-prefetchable)
0000:00:02.0 PCI bridge: ATI Technologies Inc RS480 PCI-X Root Port (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 0000e000-0000efff Memory behind bridge: fa000000-fcffffff Prefetchable memory behind bridge: 00000000d0000000-00000000dff00000 Capabilities: <available only to root>
0000:00:12.0 IDE interface: ATI Technologies Inc ATI 4379 Serial ATA Controller (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: Hewlett-Packard Company: Unknown device 2a24 Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 193 I/O ports at fe00 [size=8] I/O ports at fd00 [size=4] I/O ports at fc00 [size=8] I/O ports at fb00 [size=4] I/O ports at fa00 [size=16] Memory at fe02f000 (32-bit, non-prefetchable) [size=512] Expansion ROM at 40000000 [disabled] [size=512K] Capabilities: <available only to root>
0000:00:13.0 USB Controller: ATI Technologies Inc IXP SB400 USB Host Controller (prog-if 10 [OHCI])
Subsystem: Hewlett-Packard Company: Unknown device 2a24
Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 209
Memory at fe02e000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <available only to root>
0000:00:13.1 USB Controller: ATI Technologies Inc IXP SB400 USB Host Controller (prog-if 10 [OHCI])
Subsystem: Hewlett-Packard Company: Unknown device 2a24
Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 209
Memory at fe02d000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <available only to root>
0000:00:13.2 USB Controller: ATI Technologies Inc IXP SB400 USB2 Host Controller (prog-if 20 [EHCI])
Subsystem: Hewlett-Packard Company: Unknown device 2a24
Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 209
Memory at fe02c000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <available only to root>
0000:00:14.0 SMBus: ATI Technologies Inc IXP SB400 SMBus Controller (rev 11)
Subsystem: Hewlett-Packard Company: Unknown device 2a24
Flags: 66MHz, medium devsel
I/O ports at 0400 [size=16]
Memory at fe02b000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <available only to root>
0000:00:14.1 IDE interface: ATI Technologies Inc Standard Dual Channel PCI IDE Controller ATI (prog-if 8a [Master SecP PriP])
Subsystem: Hewlett-Packard Company: Unknown device 2a24
Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 201
I/O ports at <unassigned>
I/O ports at <unassigned>
I/O ports at <unassigned>
I/O ports at <unassigned>
I/O ports at f800 [size=16]
Capabilities: <available only to root>
0000:00:14.3 ISA bridge: ATI Technologies Inc IXP SB400 PCI-ISA Bridge
Subsystem: Hewlett-Packard Company: Unknown device 2a24
Flags: bus master, 66MHz, medium devsel, latency 0
0000:00:14.4 PCI bridge: ATI Technologies Inc IXP SB400 PCI-PCI Bridge (prog-if 01 [Subtractive decode])
Flags: bus master, 66MHz, medium devsel, latency 64
Bus: primary=00, secondary=02, subordinate=02, sec-latency=32
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fde00000-fdefffff
Prefetchable memory behind bridge: fdd00000-fddfffff
0000:00:14.5 Multimedia audio controller: ATI Technologies Inc IXP SB400 AC'97 Audio Controller (rev 02)
Subsystem: Hewlett-Packard Company: Unknown device 2a25
Flags: bus master, 66MHz, slow devsel, latency 64, IRQ 225
Memory at fe02a000 (32-bit, non-prefetchable) [size=256]
Capabilities: <available only to root>
0000:00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
Flags: fast devsel
Capabilities: <available only to root>
0000:00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
Flags: fast devsel
0000:00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
Flags: fast devsel
0000:00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
Flags: fast devsel
0000:01:00.0 VGA compatible controller: nVidia Corporation: Unknown device 0092 (rev a1) (prog-if 00 [VGA])
Subsystem: eVga.com. Corp.: Unknown device c517 Flags: bus master, fast devsel, latency 0, IRQ 5 Memory at fa000000 (32-bit, non-prefetchable) [size=16M] Memory at d0000000 (64-bit, prefetchable) [size=256M] Memory at fb000000 (64-bit, non-prefetchable) [size=16M] I/O ports at ef00 [size=128] Expansion ROM at fc000000 [disabled] [size=128K] Capabilities: <available only to root>
0000:02:01.0 Communication controller: Agere Systems V.92 56K WinModem (rev 03)
Subsystem: Agere Systems: Unknown device 044c Flags: bus master, medium devsel, latency 64, IRQ 255 Memory at fdeff000 (32-bit, non-prefetchable) [size=256] I/O ports at df00 [size=8] I/O ports at de00 [size=256] Capabilities: <available only to root>
0000:02:03.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
Subsystem: Hewlett-Packard Company: Unknown device 2a24 Flags: bus master, medium devsel, latency 64, IRQ 217 I/O ports at dd00 [size=256] Memory at fdefe000 (32-bit, non-prefetchable) [size=256] Expansion ROM at fdd00000 [disabled] [size=64K] Capabilities: <available only to root>
0000:02:04.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host Controller (rev 80) (prog-if 10 [OHCI])
Subsystem: Hewlett-Packard Company: Unknown device 2a24
Flags: bus master, medium devsel, latency 64, IRQ 169
Memory at fdefd000 (32-bit, non-prefetchable) [size=2K]
I/O ports at dc00 [size=128]
Capabilities: <available only to root>
- Chris.
Signature · 1 line
Chris Ball <[email protected]> <http://www.mrao.cam.ac.uk/~cjb/>