Skip to contentSkip to conversation

Need help with IDE/PCI config on unknown board(was: [U-Boot-Users] (no subject))

DISCUSSION Jerry K. Schieffer 2 participants 2 messages Mar 2, 2006 1 message not in the archive

lore
Share & tools
lore

A message that is not in the archive (sent off-list or not yet received): [email protected]

#1 lore raw

Thank you for your help. In answer to your questions:

Quoted 1 line
Quoted 1 line
Quoted 1 line

Can you "see" the PCI IDE controller at this address? What's the

output of:

Quoted 1 line
Quoted 1 line
Quoted 1 line

=> md.b e80001f0 10

I believe not because
=> md.b e8000000 10
e8000000: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
................

Quoted 2 lines
Quoted 2 lines
Quoted 2 lines

What's the output of:
=> pci long

=> pci long
Scanning PCI devices on bus 0

Found PCI device 00.00.00:

  vendor ID =                   0x1014
  device ID =                   0x0156
  command register =            0x0006
  status register =             0x2210
  revision ID =                 0x01
  class code =                  0x06 (Bridge device)
  sub class code =              0x00
  programming interface =       0x00
  cache line =                  0x00
  latency time =                0x07
  header type =                 0x00
  BIST =                        0x00
  base address 0 =              0x00000000
  base address 1 =              0x00000008
  base address 2 =              0x00000000
  base address 3 =              0x00000000
  base address 4 =              0x00000000
  base address 5 =              0x00000000
  cardBus CIS pointer =         0x00000000
  sub system vendor ID =        0x10e8
  sub system ID =               0xcafe
  expansion ROM base address =  0x00000000
  interrupt line =              0x00
  interrupt pin =               0x01
  min Grant =                   0x00
  max Latency =                 0x00

Found PCI device 00.04.00:

  vendor ID =                   0x105a
  device ID =                   0x0d30
  command register =            0x0004
  status register =             0x0210
  revision ID =                 0x02
  class code =                  0x01 (Mass storage controller)
  sub class code =              0x01
  programming interface =       0x8a
  cache line =                  0x00
  latency time =                0x40
  header type =                 0x00
  BIST =                        0x00
  base address 0 =              0x000001f1
  base address 1 =              0x000003f5
  base address 2 =              0x00000171
  base address 3 =              0x00000375
  base address 4 =              0x00006801
  base address 5 =              0x00000000
  cardBus CIS pointer =         0x00000000
  sub system vendor ID =        0x105a
  sub system ID =               0x4d33
  expansion ROM base address =  0x000dc000
  interrupt line =              0x1d
  interrupt pin =               0x01
  min Grant =                   0x00
  max Latency =                 0x00

=>

I suppose that the oxFF bytes are not correct for the contents of the ide controller registers.
What should I look for?

I used 0xE8000000 (apparently incorrectly) because it was reported in the following messages when initializing with the PPBBoot firmware:
PCI_Scan:Device 4 is present Bus Func 2000 ClassCode 101 IDE device found:
PCI_Config_Device:Read Base Addr Reg 0 = 0x000001f1
***PCI I/O space = 0x10 bytes 0
IDE-Just Set CFG_ATA_BASE_ADDR to e8000000^M PCI_Config_Device:Read Base Addr Reg 1 = 0x000003f5
***PCI I/O space = 0x4 bytes 10
PCI_Config_Device:Read Base Addr Reg 2 = 0x00000171
***PCI I/O space = 0x10 bytes 20
PCI_Config_Device:Read Base Addr Reg 3 = 0x00000375
***PCI I/O space = 0x4 bytes 30
PCI_Config_Device:Read Base Addr Reg 4 = 0xffffffc1
***PCI I/O space = 0x40 bytes 40
PCI_Config_Device:Read Base Addr Reg 5 = 0xfffe0000
***PCI Memory space = 0x20000 bytes
Hardcode address e80001f0

Quoted 1 line
Quoted 1 line
Quoted 1 line

PS: Please use a subject next time!

Done - see subject.

#2 lore raw

Hi Jerry,

Quoted 10 lines · Jerry K. Schieffer

Thank you for your help. In answer to your questions:

Quoted 1 line
Quoted 1 line
Quoted 1 line

Can you "see" the PCI IDE controller at this address? What's the

output of:

Quoted 1 line
Quoted 1 line
Quoted 1 line

=> md.b e80001f0 10

I believe not because
=> md.b e8000000 10
e8000000: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
................

Correct. That's _not_ the IDE controller.

Quoted 4 lines

Found PCI device 00.04.00:

  vendor ID =                   0x105a
  device ID =                   0x0d30
  command register =            0x0004

Hmmm. I/O access is not enabled. So any access to the I/O spaces will fail.

Quoted 10 lines
  status register =             0x0210
  revision ID =                 0x02
  class code =                  0x01 (Mass storage controller)
  sub class code =              0x01
  programming interface =       0x8a
  cache line =                  0x00
  latency time =                0x40
  header type =                 0x00
  BIST =                        0x00
  base address 0 =              0x000001f1

Also strange. I would expect the BAR's to be assigned to something like:

base address 0 = 0x008001f1

Then you could access this I/O space at 0xe88001f0. Here a dump from our Walnut with a PCI IDE controller:

Found PCI device 00.01.00:

  vendor ID =                   0x1191
  device ID =                   0x0009
  command register =            0x0007
  status register =             0x02b0
  revision ID =                 0x10
  class code =                  0x01 (Mass storage controller)
  sub class code =              0x80
  programming interface =       0x00
  cache line =                  0x08
  latency time =                0x80
  header type =                 0x00
  BIST =                        0x00
  base address 0 =              0x00800001
  base address 1 =              0x00800009
  base address 2 =              0x00800011
  base address 3 =              0x00800019
  base address 4 =              0x00800081
  base address 5 =              0x80000000
  cardBus CIS pointer =         0x00000000
  sub system vendor ID =        0x1191
  sub system ID =               0x0009
  expansion ROM base address =  0x40000000
  interrupt line =              0x1e
  interrupt pin =               0x01
  min Grant =                   0x0b
  max Latency =                 0x04

=> md.b e8800010 10
e8800010: 7f 7f 7f 7f 7f 7f 7f 7f ff ff 7f ff ff ff ff ff ................

Do you use the same PCI config setup as the Walnut in your board config file? Do you use the lastest U-Boot version (current GIT or CVS version)?

Best regards,
Stefan