fsample support patch (core omap only)

319 lines not on this page · raw message

@@ -1,3 +1,4 @@
+//kernel/linux-omap-fsample/arch/arm/mach-omap1/clock.c#2 - edit change 3808 (text)
 /*
  *  linux/arch/arm/mach-omap1/clock.c
  *

@@ -20,6 +21,7 @@
 
 #include <asm/io.h>
 
+#include <asm/arch/cpu.h>
 #include <asm/arch/usb.h>
 #include <asm/arch/clock.h>
 #include <asm/arch/sram.h>

@@ -270,8 +272,12 @@
 	/*
 	 * In most cases we should not need to reprogram DPLL.
 	 * Reprogramming the DPLL is tricky, it must be done from SRAM.
+	 * (on 730, bit 13 must always be 1)
 	 */
-	omap_sram_reprogram_clock(ptr->dpllctl_val, ptr->ckctl_val);
+	if (cpu_is_omap730())
+		omap_sram_reprogram_clock(ptr->dpllctl_val, ptr->ckctl_val | 0x2000);
+	else
+		omap_sram_reprogram_clock(ptr->dpllctl_val, ptr->ckctl_val);
 
 	ck_dpll1.rate = ptr->pll_rate;
 	propagate_rate(&ck_dpll1);

@@ -748,7 +754,7 @@
 		printk(KERN_ERR "System frequencies not set. Check your config.\n");
 		/* Guess sane values (60MHz) */
 		omap_writew(0x2290, DPLL_CTL);
-		omap_writew(0x1005, ARM_CKCTL);
+		omap_writew(cpu_is_omap730() ? 0x3005 : 0x1005, ARM_CKCTL);
 		ck_dpll1.rate = 60000000;
 		propagate_rate(&ck_dpll1);
 	}

@@ -761,13 +767,17 @@
 	       ck_dpll1.rate / 1000000, (ck_dpll1.rate / 100000) % 10,
 	       arm_ck.rate / 1000000, (arm_ck.rate / 100000) % 10);
 
-#ifdef CONFIG_MACH_OMAP_PERSEUS2
+#if defined(CONFIG_MACH_OMAP_PERSEUS2) || defined(CONFIG_MACH_OMAP_FSAMPLE)
 	/* Select slicer output as OMAP input clock */
 	omap_writew(omap_readw(OMAP730_PCC_UPLD_CTRL) & ~0x1, OMAP730_PCC_UPLD_CTRL);
 #endif
 
 	/* Turn off DSP and ARM_TIMXO. Make sure ARM_INTHCK is not divided */
-	omap_writew(omap_readw(ARM_CKCTL) & 0x0fff, ARM_CKCTL);
+	/* (on 730, bit 13 must not be cleared) */
+	if (cpu_is_omap730())
+		omap_writew(omap_readw(ARM_CKCTL) & 0x2fff, ARM_CKCTL);
+	else
+		omap_writew(omap_readw(ARM_CKCTL) & 0x0fff, ARM_CKCTL);
 
 	/* Put DSP/MPUI into reset until needed */
 	omap_writew(0, ARM_RSTCT1);

@@ -1,3 +1,4 @@
+//kernel/linux-omap-fsample/arch/arm/mach-omap1/pm.c#3 - integrate change 4545 (text)
 /*
  * linux/arch/arm/mach-omap1/pm.c
  *

@@ -50,6 +51,7 @@
 #include <asm/mach/irq.h>
 #include <asm/mach-types.h>
 
+#include <asm/arch/cpu.h>
 #include <asm/arch/irqs.h>
 #include <asm/arch/clock.h>
 #include <asm/arch/sram.h>

@@ -326,8 +328,9 @@
 	/* stop DSP */
 	omap_writew(omap_readw(ARM_RSTCT1) & ~(1 << DSP_EN), ARM_RSTCT1);
 
-	/* shut down dsp_ck */
-	omap_writew(omap_readw(ARM_CKCTL) & ~(1 << EN_DSPCK), ARM_CKCTL);
+		/* shut down dsp_ck */
+	if (!cpu_is_omap730())
+		omap_writew(omap_readw(ARM_CKCTL) & ~(1 << EN_DSPCK), ARM_CKCTL);
 
 	/* temporarily enabling api_ck to access DSP registers */
 	omap_writew(omap_readw(ARM_IDLECT2) | 1 << EN_APICK, ARM_IDLECT2);

@@ -94,7 +94,7 @@
  * will break. On P2, the timer count rate is 6.5 MHz after programming PTV
  * with 0. This divides the 13MHz input by 2, and is undocumented.
  */
-#ifdef CONFIG_MACH_OMAP_PERSEUS2
+#if defined(CONFIG_MACH_OMAP_PERSEUS2) || defined(CONFIG_MACH_OMAP_FSAMPLE)
 /* REVISIT: This ifdef construct should be replaced by a query to clock
  * framework to see if timer base frequency is 12.0, 13.0 or 19.2 MHz.
  */

@@ -105,7 +105,7 @@
 		omap_cfg_reg(E20_1610_KBR3);
 		omap_cfg_reg(E19_1610_KBR4);
 		omap_cfg_reg(N19_1610_KBR5);
-	} else if (machine_is_omap_perseus2()) {
+	} else if (machine_is_omap_perseus2() || machine_is_omap_fsample()) {
 		omap_cfg_reg(E2_730_KBR0);
 		omap_cfg_reg(J7_730_KBR1);
 		omap_cfg_reg(E1_730_KBR2);

51 lines not on this page · raw message

@@ -298,6 +298,10 @@
 #include "board-perseus2.h"
 #endif
 
+#ifdef CONFIG_MACH_OMAP_FSAMPLE
+#include "board-fsample.h"
+#endif
+
 #ifdef CONFIG_MACH_OMAP_H3
 #include "board-h3.h"
 #endif