Skip to contentSkip to conversation

u-boot fails at cpu_init_f

U-Boot-Users shangway 2 participants 2 messages May 9, 2006

lore
Share & tools
lore

shangway

author
#0 lore raw

Hi all,

I'm trying to get u-boot to run on a proprietary 8540 based board. The board is similar to the MPC8540ADS which configuration I used to build u-boot. I am using eldk 4.0. I managed to download u-boot to flash, but I am unable to run it. By stepping through the code, I found that it fails in the first c-function "cpu_init_f".

This is the assembly code for cpu_init_f:

fff82e10 <cpu_init_f>:

fff82e10:	94 21 ff f0 	stwu    r1,-16(r1)
fff82e14:	3c 60 e4 01 	lis     r3,-7167
fff82e18:	7c 08 02 a6 	mflr    r0
fff82e1c:	60 63 3f 80 	ori     r3,r3,16256
fff82e20:	38 80 00 00 	li      r4,0
fff82e24:	38 a0 00 30 	li      r5,48
fff82e28:	90 01 00 14 	stw     r0,20(r1)
fff82e2c:	48 00 59 b1 	bl      fff887dc <memset>
fff82e30:	3c 00 ff 00 	lis     r0,-256
fff82e34:	3d 20 e0 00 	lis     r9,-8192
fff82e38:	60 00 18 01 	ori     r0,r0,6145
fff82e3c:	3d 60 ff 00 	lis     r11,-256
fff82e40:	90 09 50 00 	stw     r0,20480(r9)
fff82e44:	61 6b 6f f7 	ori     r11,r11,28663
fff82e48:	38 00 e1 f1 	li      r0,-7695
fff82e4c:	91 69 50 04 	stw     r11,20484(r9)
fff82e50:	3d 40 f8 00 	lis     r10,-2048
fff82e54:	90 09 50 24 	stw     r0,20516(r9)
fff82e58:	61 4a 08 01 	ori     r10,r10,2049
fff82e5c:	80 01 00 14 	lwz     r0,20(r1)
fff82e60:	38 21 00 10 	addi    r1,r1,16
fff82e64:	91 49 50 20 	stw     r10,20512(r9)
fff82e68:	7c 08 03 a6 	mtlr    r0

fff82e6c: 4e 80 00 20 blr
fff82e70: 00 02 86 0c .long 0x2860c

The code runs fine (at least that's what I think) until 0xfff82e5c. The cpu hangs when I try to execute that instruction. This is the first time, that there is a load from an address which is not in flash, so I suspect, that setting up the cache as RAM failed. I also tried to manually write data to that location with gdb, but I read only 0x0.
As this is still in the initialization process of the cpu, I don't think that it is related to a possibly wrong board configuration, or am I wrong.

Any ideas?

Thanks in advance and best regards,

Gordon.

__________________________________________________
Do You Yahoo!?
Tired of spam? Yahoo! Mail has the best spam protection around
http://mail.yahoo.com

#1 lore raw

Gordon,

The piece of code which you mention:

       fff82e5c:	80 01 00 14 	lwz     r0,20(r1)
       fff82e60:	38 21 00 10 	addi    r1,r1,16

is part of the "return" process from the routine back to its caller. r1 is pointing at the C run-time stack.

The code that sets up this stack is in the assembler routine

in_flash

in file start.S for the 85xx cpus.

Usually, the 8540 is configured so that the initial runtime stack consists of 16 KB of memory locked into L1 cache meaning that the L1 cache is in effect providing the actual RAM.

You might need to check the configuration in init.S for your board to see that this is being set up properly and then check that the address range is configured into TLB0 during execution.

Charles.

-----Original Message-----
From: [email protected] [mailto:u-boot-users-admin at lists.sourceforge.net] On Behalf Of shangway
Sent: 09 May 2006 03:58
To: u-boot-users at lists.sourceforge.net
Subject: [U-Boot-Users] u-boot fails at cpu_init_f

Hi all,

I'm trying to get u-boot to run on a proprietary 8540 based board. The board is similar to the MPC8540ADS which configuration I used to build u-boot. I am using eldk 4.0. I managed to download u-boot to flash, but I am unable to run it. By stepping through the code, I found that it fails in the first c-function "cpu_init_f".

This is the assembly code for cpu_init_f:

fff82e10 <cpu_init_f>:

fff82e10:	94 21 ff f0 	stwu    r1,-16(r1)
fff82e14:	3c 60 e4 01 	lis     r3,-7167
fff82e18:	7c 08 02 a6 	mflr    r0
fff82e1c:	60 63 3f 80 	ori     r3,r3,16256
fff82e20:	38 80 00 00 	li      r4,0
fff82e24:	38 a0 00 30 	li      r5,48
fff82e28:	90 01 00 14 	stw     r0,20(r1)
fff82e2c:	48 00 59 b1 	bl      fff887dc <memset>
fff82e30:	3c 00 ff 00 	lis     r0,-256
fff82e34:	3d 20 e0 00 	lis     r9,-8192
fff82e38:	60 00 18 01 	ori     r0,r0,6145
fff82e3c:	3d 60 ff 00 	lis     r11,-256
fff82e40:	90 09 50 00 	stw     r0,20480(r9)
fff82e44:	61 6b 6f f7 	ori     r11,r11,28663
fff82e48:	38 00 e1 f1 	li      r0,-7695
fff82e4c:	91 69 50 04 	stw     r11,20484(r9)
fff82e50:	3d 40 f8 00 	lis     r10,-2048
fff82e54:	90 09 50 24 	stw     r0,20516(r9)
fff82e58:	61 4a 08 01 	ori     r10,r10,2049
fff82e5c:	80 01 00 14 	lwz     r0,20(r1)
fff82e60:	38 21 00 10 	addi    r1,r1,16
fff82e64:	91 49 50 20 	stw     r10,20512(r9)
fff82e68:	7c 08 03 a6 	mtlr    r0

fff82e6c: 4e 80 00 20 blr
fff82e70: 00 02 86 0c .long 0x2860c

The code runs fine (at least that's what I think) until 0xfff82e5c. The cpu hangs when I try to execute that instruction. This is the first time, that there is a load from an address which is not in flash, so I suspect, that setting up the cache as RAM failed. I also tried to manually write data to that location with gdb, but I read only 0x0.
As this is still in the initialization process of the cpu, I don't think that it is related to a possibly wrong board configuration, or am I wrong.

Any ideas?

Thanks in advance and best regards,

Gordon.

__________________________________________________
Do You Yahoo!?
Tired of spam? Yahoo! Mail has the best spam protection around
http://mail.yahoo.com

-------------------------------------------------------
Using Tomcat but need to do more? Need to support web services, security? Get stuff done quickly with pre-integrated technology to make your job easier
Download IBM WebSphere Application Server v.1.0.1 based on Apache Geronimo
http://sel.as-us.falkag.net/sel?cmd=lnk&kid=120709&bid=263057&dat=121642
_______________________________________________
U-Boot-Users mailing list
U-Boot-Users at lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/u-boot-users