Skip to contentSkip to conversation

AT91RM9200 Dataflash op error with U-Boot1.1.4

U-Boot-Users KylongMu 2 participants 2 messages May 9, 2006 1 message not in the archive

lore
Share & tools
lore

A message that is not in the archive (sent off-list or not yet received): [email protected]

KylongMu

author
#1 lore raw
Quoted 12 lines · KylongMu
Quoted 3 lines

Dear Groups:
My board contains: AT91RM9200 DataFlash:AT45DB642 (without nand
flash)

...

Quoted 4 lines

U-Boot> erase c0020000 c0027fff
Error: start address not on sector boundary
U-Boot>

--------------------------------------------------------------------------
--

Quoted 1 line
Quoted 6 lines
Quoted 2 lines

Does anybody know how to solve with this?
Thanks a lot!

Perhaps, this patch will help you:

--- u-boot-1.1.3/common/cmd_mem.c 2005-09-14 22:45:12.000000000

+0400

Quoted 1 line

+++ u-boot-1.1.3-new/common/cmd_mem.c 2005-09-14 22:47:03.000000000

+0400

common/flash.c 2005-09-15 01:15:58.000000000

Quoted 14 lines
(quoted diff) +1 -1
@@ -423,7 +423,7 @@
        /* check if we are copying to Flash */
        if ( (addr2info(dest) != NULL)
 #ifdef CONFIG_HAS_DATAFLASH
-          && (!addr_dataflash(addr))
+          && (!addr_dataflash(addr)) && (!addr_dataflash(dest))
 #endif
           ) {
                int rc;

If it will not solve the problem, try this:

common/flash.c 2005-09-15 01:15:58.000000000 renamed from common/flash.c 2005-08-14 03:53:35.000000000 +0400 +0 -0

+0400

common/flash.c 2005-09-15 01:15:58.000000000 line 107

Quoted 4 lines
common/flash.c 2005-09-15 01:15:58.000000000 renamed from common/flash.c 2005-08-14 03:53:35.000000000 +0400 +0 -0
@@ -105,6 +105,8 @@
        int i;
 
        for (i=0, info=&flash_info[0]; i<CFG_MAX_FLASH_BANKS; ++i, ++info)

{

Quoted 9 lines
common/flash.c 2005-09-15 01:15:58.000000000 renamed from common/flash.c 2005-08-14 03:53:35.000000000 +0400 +2 -1
+               if (info->size == 0)
+                       continue;
                if (info->flash_id != FLASH_UNKNOWN &&
                    addr >= info->start[0] &&
                    /* WARNING - The '- 1' is needed if the flash
 
--

With best regards,
Andrey Vasilyev

Dear Andrey,
Thanks for your answer. I patched these two files one by one, or
both of them, but all failed, and the error is still.
Thanks a lot!
KylongMu

#2 lore raw
Quoted 10 lines · KylongMu
Quoted 10 lines · KylongMu
Quoted 3 lines

Dear Groups:
My board contains: AT91RM9200 DataFlash:AT45DB642 (without nand
flash)

...

Quoted 3 lines

U-Boot> erase c0020000 c0027fff
Error: start address not on sector boundary
U-Boot>

Perhaps, this patch will help you:

...

Quoted 1 line
Quoted 1 line

If it will not solve the problem, try this:

...

Quoted 5 lines

Dear Andrey,
Thanks for your answer. I patched these two files one by one, or
both of them, but all failed, and the error is still.
Thanks a lot!

Oops... My mistake. I've replied without carefully reading your question...
Right answer (I hope): you dont need to erase dataflash. AFAIK, dataflash erasing is performed by driver when you write into dataflash. So, for example, to download binary into c0042000 dataflash "virtual" address, you can use simple "cp" command, without issuing "erase" command first, like this:

loadb 21000000
<sending image 0x12345 bytes long by kermit>
cp.b 21000000 c0042000 12345

Signature · 2 lines
With best regards,
  Andrey Vasilyev