Skip to contentSkip to conversation

2.6.17-rc4-mm1 panic on boot

DISCUSSION [email protected] 2 participants 4 messages May 16, 2006

lore
Share & tools
lore
#0 lore raw

Just upgraded from rc3-mm4.
Panic on boot with this message (copied by hand ):

	kinit:do_mount
	kinit: name_to_dev_t(/dev/hda8) = dev (0,0)
	kinit:rot_dev = dev (0,0)
	kinit root_dev = dev (0,0)
	kinit trying to mount /dev/root on /root
	...........

/dev/hda8 is my root partition but I suppose dev (0,0) is the first partition on hda which is FAT.
I tried vanilla rc4 with the same result.

#1 lore raw
Followup to:  <20060516001501.GA7528@localhost>
By author:    [email protected]
In newsgroup: linux.dev.kernel
Quoted 9 lines

Just upgraded from rc3-mm4.
Panic on boot with this message (copied by hand ):

	kinit:do_mount
	kinit: name_to_dev_t(/dev/hda8) = dev (0,0)
	kinit:rot_dev = dev (0,0)
	kinit root_dev = dev (0,0)
	kinit trying to mount /dev/root on /root
	...........
Quoted 4 lines

/dev/hda8 is my root partition but I suppose dev (0,0) is the first partition on hda which is FAT.
I tried vanilla rc4 with the same result.

This means kinit couldn't find a name-to-number mapping for the string /dev/hda8. However, you said you tried vanilla rc4 with the same result, and vanilla rc4 doesn't use klibc.

This means hda8 simply isn't discovered on your system, which probably means hda isn't discovered. This typically is an issue with your kernel configuration, but it's not always.

There should be somewhere in your boot messages a message such as the following:

Probing IDE interface ide0...
hda: WDC WD2500JB-00EVA0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 1024KiB
hda: 488397168 sectors (250059 MB) w/8192KiB Cache, CHS=30401/255/63, UDMA(100)
hda: cache flushes supported
hda: hda1 hda2 hda3 hda4

Does this show up in your successful boots? Failing boots?

-hpa

#2 lore raw
Quoted 17 lines · H. Peter Anvin
Followup to:  <20060516001501.GA7528@localhost>
By author:    [email protected]
In newsgroup: linux.dev.kernel
Quoted 9 lines

Just upgraded from rc3-mm4.
Panic on boot with this message (copied by hand ):

	kinit:do_mount
	kinit: name_to_dev_t(/dev/hda8) = dev (0,0)
	kinit:rot_dev = dev (0,0)
	kinit root_dev = dev (0,0)
	kinit trying to mount /dev/root on /root
	...........
Quoted 4 lines

/dev/hda8 is my root partition but I suppose dev (0,0) is the first partition on hda which is FAT.
I tried vanilla rc4 with the same result.

Quoted 3 lines

This means kinit couldn't find a name-to-number mapping for the string /dev/hda8. However, you said you tried vanilla rc4 with the same result, and vanilla rc4 doesn't use klibc.

Sorry for my silliness, actually rc4 boot OK

Quoted 4 lines

This means hda8 simply isn't discovered on your system, which probably means hda isn't discovered. This typically is an issue with your kernel configuration, but it's not always.

yes that was my problem: rc4-mm1 need CONFIG_SCSI_PATA_AMD=y which -rc4 don't for my nForce2 ide controller.

many thankx

#3 lore raw
Quoted 11 lines · Leopold Gouverneur
Quoted 4 lines

This means kinit couldn't find a name-to-number mapping for the string /dev/hda8. However, you said you tried vanilla rc4 with the same result, and vanilla rc4 doesn't use klibc.

Sorry for my silliness, actually rc4 boot OK

Quoted 3 lines

This means hda8 simply isn't discovered on your system, which probably means hda isn't discovered. This typically is an issue with your kernel configuration, but it's not always.

yes that was my problem: rc4-mm1 need CONFIG_SCSI_PATA_AMD=y which -rc4 don't for my nForce2 ide controller.

Excellent, glad to hear that it was that simple.

-hpa