Skip to contentSkip to conversation

2.6.17.1 perfmon2 patch for review: PMU context switch

PATCH Chuck Ebbert 2 participants 2 messages Jul 6, 2006

lore
Share & tools
lore
#0 lore raw

In-Reply-To: <[email protected]>

Quoted 13 lines · Stephan Eranian

Here is what I get on my dual 2.4GHz Opteron 250:

booted with idle=halt

$ pfmon --us-c -ecpu_clk_unhalted,interrupts_masked_cycles_with_interrupt_pending,interrupts_masked_cycles,cycles_no_fpu_ops_retired -k --system-wide -t 10
<session to end in 10 seconds>
CPU0                    11,356,210 CPU_CLK_UNHALTED                               
CPU0                             0 INTERRUPTS_MASKED_CYCLES_WITH_INTERRUPT_PENDING
CPU0                     3,836,107 INTERRUPTS_MASKED_CYCLES                       
CPU0                23,910,784,532 CYCLES_NO_FPU_OPS_RETIRED                      
CPU1                    19,303,632 CPU_CLK_UNHALTED                               
CPU1                             0 INTERRUPTS_MASKED_CYCLES_WITH_INTERRUPT_PENDING
CPU1                    13,942,265 INTERRUPTS_MASKED_CYCLES                       
CPU1                23,911,872,654 CYCLES_NO_FPU_OPS_RETIRED                      

So it looks like your Opteron continues to count CYCLES_NO_FPU_OPS_RETIRED at full clock speed even when halted.

My Turion appears to slow down to ~40 MHz when halted and counts those events at that speed. Using idle=poll shows no slowdown, as expected, and unhalted clocks equals cycles_no_fpu_ops_retired.

Signature · 2 lines
Chuck
 "You can't read a newspaper if you can't read."  --George W. Bush
#1 lore raw

Chuck,

Quoted 18 lines · Chuck Ebbert

In-Reply-To: <[email protected]>

Quoted 13 lines · Stephan Eranian

Here is what I get on my dual 2.4GHz Opteron 250:

booted with idle=halt

$ pfmon --us-c -ecpu_clk_unhalted,interrupts_masked_cycles_with_interrupt_pending,interrupts_masked_cycles,cycles_no_fpu_ops_retired -k --system-wide -t 10
<session to end in 10 seconds>
CPU0                    11,356,210 CPU_CLK_UNHALTED                               
CPU0                             0 INTERRUPTS_MASKED_CYCLES_WITH_INTERRUPT_PENDING
CPU0                     3,836,107 INTERRUPTS_MASKED_CYCLES                       
CPU0                23,910,784,532 CYCLES_NO_FPU_OPS_RETIRED                      
CPU1                    19,303,632 CPU_CLK_UNHALTED                               
CPU1                             0 INTERRUPTS_MASKED_CYCLES_WITH_INTERRUPT_PENDING
CPU1                    13,942,265 INTERRUPTS_MASKED_CYCLES                       
CPU1                23,911,872,654 CYCLES_NO_FPU_OPS_RETIRED                      
Quoted 3 lines

So it looks like your Opteron continues to count CYCLES_NO_FPU_OPS_RETIRED at full clock speed even when halted.

Yes, it certainly looks like it, idling at full clock speed. But that's a server CPU! I think this may have to do with latency to get back to useful work.

Quoted 4 lines

My Turion appears to slow down to ~40 MHz when halted and counts those events at that speed. Using idle=poll shows no slowdown, as expected, and unhalted clocks equals cycles_no_fpu_ops_retired.

That's a mobile processor, so I would expect it to use more aggressive power-saving scheme while idle, at the cost of higher latency to get back to full speed.

The good thing about this is that it was not too hard to figure out what is going using pfmon. Where you specifically looking for this? Is this a documented behavior of the Turion64?

Signature · 1 line
-Stephane