USB device stopped working - can't set config #1, error -71
Hi all,
with the latest kernels (definetly 2.6.17 and 1.6.8-rc*, I do now know off hand when this started) I can not access some (I think all USB 1) scanners via my SANE/Avision backend:
usb 3-1: new full speed USB device using uhci_hcd and address 2 usb 3-1: configuration #1 chosen from 1 choice
usb 3-1: can't set config #1, error -71
write(2, "attach: opening libusb:003:002\n", 31) = 31open("/proc/bus/usb/003/002", O_RDWR) = 4ioctl(4, USBDEVFS_SETCONFIGURATION, 0xbfc10c74) = -1 EPROTO (Protocol error)
close(4) = 0fstat64(2, {st_mode=S_IFCHR|0600, st_rdev=makedev(136, 1), ...}) = 0write(2, "[avision] ", 10) = 10
write(2, "attach: open failed (Invalid arg"..., 39) = 39
Currently this is on an x86 Apple MacBook:
Bus 005 Device 002: ID 05ac:1000 Apple Computer
Bus 005 Device 001: ID 0000:0000 Virtual Hub
Bus 004 Device 002: ID 05ac:8240 Apple Computer
Bus 004 Device 001: ID 0000:0000 Virtual Hub
Bus 003 Device 001: ID 0000:0000 Virtual Hub
Bus 002 Device 002: ID 05ac:0218 Apple Computer
Bus 002 Device 001: ID 0000:0000 Virtual Hub
Bus 001 Device 009: ID 05ac:020c Apple Computer
Bus 001 Device 008: ID 046d:c00c Logitech Inc. Optical Wheel Mouse Bus 001 Device 007: ID 05ac:1003 Apple Computer
Bus 001 Device 004: ID 05ac:8300 Apple Computer
Bus 001 Device 002: ID 05e3:0606 Genesys Logic, Inc. Bus 001 Device 001: ID 0000:0000 Virtual Hub
While this simple lsusb is enough to trigger the issue:
usb 3-1: new full speed USB device using uhci_hcd and address 3 usb 3-1: configuration #1 chosen from 1 choice
usb 3-1: can't set config #1, error -71
And the affected devices do not appear in the lsusb output.
Btw: I saw a patch related to usb1 devics behind usb2 hubs, but I think it made no difference here.
Btw2: I also do not see the standard bluetooth USB HCI that is suppost to be in the MacBook and that is listed and works fine in OS X.
Yours,
Signature · 3 lines
René Rebe - ExactCODE - Berlin (Europe / Germany) http://exactcode.de | http://t2-project.org | http://rene.rebe.name +49 (0)30 / 255 897 45
Quoted 9 lines · Rene Rebe
Hi all,
with the latest kernels (definetly 2.6.17 and 1.6.8-rc*, I do now know off hand when this started) I can not access some (I think all USB 1) scanners via my SANE/Avision backend:
usb 3-1: new full speed USB device using
uhci_hcdand address 2 usb 3-1: configuration #1 chosen from 1 choice
usb 3-1: can't set config #1, error -71
This is bad already. All the rest of the stuff below is just more of the same.
Quoted 30 lines
write(2, "attach: opening libusb:003:002\n", 31)= 31open("/proc/bus/usb/003/002", O_RDWR)= 4ioctl(4, USBDEVFS_SETCONFIGURATION, 0xbfc10c74)= -1 EPROTO (Protocol error)
close(4) = 0fstat64(2, {st_mode=S_IFCHR|0600, st_rdev=makedev(136, 1), ...})= 0write(2, "[avision] ", 10)= 10
write(2, "attach: open failed (Invalid arg"..., 39) = 39Currently this is on an x86 Apple MacBook:
Bus 005 Device 002: ID 05ac:1000 Apple Computer
Bus 005 Device 001: ID 0000:0000 Virtual Hub
Bus 004 Device 002: ID 05ac:8240 Apple Computer
Bus 004 Device 001: ID 0000:0000 Virtual Hub
Bus 003 Device 001: ID 0000:0000 Virtual Hub
Bus 002 Device 002: ID 05ac:0218 Apple Computer
Bus 002 Device 001: ID 0000:0000 Virtual Hub
Bus 001 Device 009: ID 05ac:020c Apple Computer
Bus 001 Device 008: ID 046d:c00c Logitech Inc. Optical Wheel Mouse Bus 001 Device 007: ID 05ac:1003 Apple Computer
Bus 001 Device 004: ID 05ac:8300 Apple Computer
Bus 001 Device 002: ID 05e3:0606 Genesys Logic, Inc. Bus 001 Device 001: ID 0000:0000 Virtual HubWhile this simple lsusb is enough to trigger the issue:
usb 3-1: new full speed USB device using
uhci_hcdand address 3 usb 3-1: configuration #1 chosen from 1 choice
usb 3-1: can't set config #1, error -71
Quoted 7 lines
And the affected devices do not appear in the lsusb output.
Btw: I saw a patch related to usb1 devics behind usb2 hubs, but I think it made no difference here.
Btw2: I also do not see the standard bluetooth USB HCI that is suppost to be in the MacBook and that is listed and works fine in OS X.
Try using usbmon to watch what happens when you plug in your scanner. Instructions are in the kernel source file Documentation/usb/usbmon.txt.
Alan Stern
Quoted 6 lines · Alan Stern
with the latest kernels (definetly 2.6.17 and 1.6.8-rc*, I do now know off hand when this started) I can not access some (I think all USB 1) scanners via my SANE/Avision backend:
[...]
Try using usbmon to watch what happens when you plug in your scanner. Instructions are in the kernel source fileDocumentation/usb/usbmon.txt.
I second that. But it would also help a lot to find a kernel which worked, even if it's relatively old, so we'd try to diff the hub.c.
-- Pete