mptspi : Bug fix to prevent infinite nested domain validation
Subsystems (2)
PATCH 1/1 mptspi : Bug fix to prevent infinite nested domain validation
This event occurs when dv sends an inquiry to a device, and the device never returns, thus timing out. This results in a task_abort, followed by host_reset.
Quoted 1 line
From
host_reset, domain validation is invoked again, and this
loop repeats itself forever.
Invoking domain validation from host_reset is required, as device go to slowest speed, asyn narrow.
The fix I propose is to keep a bitwise flag hd->spi_pending that keeps track of the devices that are in progress of domain validation. Then when host_reset occurs, we see if the flag is non-zero, then take a different path which program devices to old nego parameters, instead of calling dv again. We do nothing for the device that currently in the middle of dv. When hd->spi_pending is zero, then dv is performed on all devices.
Please note, we tried using the starget_data->dv_pending flag from host_reset, by calling dv for devices not pending, and this doesn't work. The reason is if there is a faulty device with a high id, such as 10, by the time we loop back to that id, the dv_pending flag was always was zero, thus dv looped again. Using the hd->spi_pending prevents nested dv, and at the same time programs the devices back to previous nego.
drivers/message/fusion/mptbase.h +1 -0
@@ -981,6 +981,7 @@ typedef struct _MPT_SCSI_HOST {int scandv_wait_done;long last_queue_full;u16 tm_iocstatus; +u16 spi_pending; }MPT_SCSI_HOST ;/*=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=*/
drivers/message/fusion/mptspi.c +21 -2
@@ -302,7 +302,9 @@ static void mptspi_dv_device(struct _MPTreturn ; } + hd->spi_pending |= (1 << sdev->id);spi_dv_device (sdev); + hd->spi_pending &= ~(1 << sdev->id);if (sdev->channel ==1 &&mptscsih_quiesce_raid (hd,0 , vtarget->target_id) <0 )
@@ -789,11 +791,27 @@ mptspi_dv_renegotiate_work(void *data)struct work_queue_wrapper *wqw = (struct work_queue_wrapper *)data;struct _MPT_SCSI_HOST *hd = wqw->hd;struct scsi_device *sdev; +struct scsi_target *starget; +struct _CONFIG_PAGE_SCSI_DEVICE_1 pg1; +u32 nego;kfree (wqw); -shost_for_each_device (sdev, hd->ioc->sh) -mptspi_dv_device (hd, sdev); +if (hd->spi_pending) { +shost_for_each_device (sdev, hd->ioc->sh) { +if (hd->spi_pending & (1 << sdev->id)) +continue ; + starget =scsi_target (sdev); + nego =mptspi_getRP (starget); + pg1.RequestedParameters =cpu_to_le32 (nego); + pg1.Reserved =0 ; + pg1.Configuration =0 ; +mptspi_write_spi_device_pg1 (starget, &pg1); + } + }else { +shost_for_each_device (sdev, hd->ioc->sh) +mptspi_dv_device (hd, sdev); + } } static void
@@ -1054,6 +1072,7 @@ mptspi_probe(struct pci_dev *pdev, constinit_waitqueue_head (&hd->scandv_waitq); hd->scandv_wait_done =0 ; hd->last_queue_full =0 ; + hd->spi_pending =0 ;/* Some versions of the firmware don't support page 0; without * that we can't get the parameters */
Quoted 18 lines · Eric Moore
This event occurs when dv sends an inquiry to a device, and the device never returns, thus timing out. This results in a
task_abort, followed byhost_reset.Quoted 1 line
From
host_reset, domain validation is invoked again, and thisloop repeats itself forever.
Invoking domain validation from
host_resetis required, as device go to slowest speed, asyn narrow.The fix I propose is to keep a bitwise flag
hd->spi_pendingthat keeps track of the devices that are in progress of domain validation. Then whenhost_resetoccurs, we see if the flag is non-zero, then take a different path which program devices to old nego parameters, instead of calling dv again. We do nothing for the device that currently in the middle of dv. Whenhd->spi_pendingis zero, then dv is performed on all devices.
Quoted 7 lines
Please note, we tried using the
starget_data->dv_pendingflag fromhost_reset, by calling dv for devices not pending, and this doesn't work. The reason is if there is a faulty device with a high id, such as 10, by the time we loop back to that id, thedv_pendingflag was always was zero, thus dv looped again. Using thehd->spi_pendingprevents nested dv, and at the same time programs the devices back to previous nego.
Erm, but surely, since reset->dv is fairly standard, this must need a generic fix.
Can you check this out. I think it does the right thing gating spi_dv_device() with a new flag. The pending flag is more used to
manage scheduled domain validations. The original idea was that resets
would trigger scheduled dv that would use this flag correctly (and not be in the direct path of DV). For some reason the mptspi seems to manage to entangle DV with the reset inline.
James
drivers/scsi/scsi_transport_spi.c +7 -0
@@ -47,6 +47,7 @@ #define DV_RETRIES 3 /* should only need/* Private data accessors (keep these out of the header file) */ #define spi_dv_pending (x) (((struct spi_transport_attrs *)&(x)->starget_data)->dv_pending) +#define spi_dv_in_progress (x) (((struct spi_transport_attrs *)&(x)->starget_data)->dv_in_progress)#define spi_dv_mutex (x) (((struct spi_transport_attrs *)&(x)->starget_data)->dv_mutex)struct spi_internal {
@@ -240,6 +241,7 @@ static int spi_setup_transport_attrs(strspi_pcomp_en (starget) =0 ;spi_hold_mcs (starget) =0 ;spi_dv_pending (starget) =0 ; +spi_dv_in_progress (starget) =0 ;spi_initial_dv (starget) =0 ;mutex_init (&spi_dv_mutex (starget));
@@ -907,6 +909,10 @@ spi_dv_device(struct scsi_device *sdev)if (unlikely (scsi_device_get (sdev)))return ; +if (unlikely (spi_dv_in_progress (starget))) +return ; +spi_dv_in_progress (starget) =1 ; + buffer =kzalloc (len,GFP_KERNEL );if (unlikely (!buffer))
@@ -938,6 +944,7 @@ spi_dv_device(struct scsi_device *sdev) out_free:kfree (buffer); out_put: +spi_dv_in_progress (starget) =0 ;scsi_device_put (sdev); }EXPORT_SYMBOL (spi_dv_device);
Quoted 30 lines · James Bottomley
Quoted 18 lines · Eric Moore
This event occurs when dv sends an inquiry to a device, and the device never returns, thus timing out. This results in a
task_abort, followed byhost_reset.Quoted 1 line
From
host_reset, domain validation is invoked again, and thisloop repeats itself forever.
Invoking domain validation from
host_resetis required, as device go to slowest speed, asyn narrow.The fix I propose is to keep a bitwise flag
hd->spi_pendingthat keeps track of the devices that are in progress of domain validation. Then whenhost_resetoccurs, we see if the flag is non-zero, then take a different path which program devices to old nego parameters, instead of calling dv again. We do nothing for the device that currently in the middle of dv. Whenhd->spi_pendingis zero, then dv is performed on all devices.Quoted 7 lines
Please note, we tried using the
starget_data->dv_pendingflag fromhost_reset, by calling dv for devices not pending, and this doesn't work. The reason is if there is a faulty device with a high id, such as 10, by the time we loop back to that id, thedv_pendingflag was always was zero, thus dv looped again. Using thehd->spi_pendingprevents nested dv, and at the same time programs the devices back to previous nego.Erm, but surely, since
reset->dvis fairly standard, this must need a generic fix.
Quoted 6 lines
Can you check this out. I think it does the right thing gating
spi_dv_device()with a new flag. The pending flag is more used to
manage scheduled domain validations. The original idea was that resets
would trigger scheduled dv that would use this flag correctly (and not be in the direct path of DV). For some reason the mptspi seems to manage to entangle DV with the reset inline.
I applied this patch (I needed to add this to get it to compile.
include/scsi/scsi_transport_spi.h 2006-09-19 12:30:53.000000000 -0700 renamed from include/scsi/scsi_transport_spi.h 2006-07-10 13:33:13.000000000 -0700 +1 -0
@@ -54,6 +54,7 @@ unsigned int support_qas; /* supports quick arbitration and selection */ /* Private Fields */ unsigned int dv_pending:1; /* Internal flag */ + unsigned int dv_in_progress:1; /* Internal flag */ struct mutex dv_mutex; /* semaphore to serialise dv */ };
It does take quite a while. It has been going for over 8 minutes and isn't done yet. Here is the log so far:
Sep 19 13:40:08 stp4-000 Fusion MPT base driver 3.04.01
Sep 19 13:40:08 stp4-000 Copyright (c) 1999-2005 LSI Logic Corporation
Sep 19 13:40:08 stp4-000 Fusion MPT SPI Host driver 3.04.01
Sep 19 13:40:08 stp4-000 mptbase: Initiating ioc0 bringup
Sep 19 13:40:09 stp4-000 ioc0: 53C1030: Capabilities={Initiator}
Sep 19 13:40:10 stp4-000 scsi1 : ioc0: LSI53C1030, FwRev=01030a00h, Ports=1, MaxQ=222, IRQ=20
Sep 19 13:40:12 stp4-000 scsi 1:0:1:0: Direct access HP 18.2GB C 80-H008 H008 PQ: 0 ANSI: 2
Sep 19 13:40:12 stp4-000 target1:0:1: Beginning Domain Validation
Sep 19 13:40:12 stp4-000 target1:0:1: Ending Domain Validation
Sep 19 13:40:12 stp4-000 target1:0:1: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:40:12 stp4-000 SCSI device sdb: 35566480 512-byte hdwr sectors (18210 MB)
Sep 19 13:40:12 stp4-000 sdb: Write Protect is off
Sep 19 13:40:12 stp4-000 sdb: Mode Sense: a7 00 10 08
Sep 19 13:40:12 stp4-000 SCSI device sdb: drive cache: write back w/ FUA
Sep 19 13:40:12 stp4-000 SCSI device sdb: 35566480 512-byte hdwr sectors (18210 MB)
Sep 19 13:40:12 stp4-000 sdb: Write Protect is off
Sep 19 13:40:12 stp4-000 sdb: Mode Sense: a7 00 10 08
Sep 19 13:40:12 stp4-000 SCSI device sdb: drive cache: write back w/ FUA
Sep 19 13:40:12 stp4-000 sdb: sdb1
Sep 19 13:40:12 stp4-000 sd 1:0:1:0: Attached scsi disk sdb
Sep 19 13:40:12 stp4-000 sd 1:0:1:0: Attached scsi generic sg1 type 0
Sep 19 13:40:12 stp4-000 scsi 1:0:2:0: Direct access HP 18.2GB C 80-H008 H008 PQ: 0 ANSI: 2
Sep 19 13:40:12 stp4-000 target1:0:2: Beginning Domain Validation
Sep 19 13:40:12 stp4-000 target1:0:2: Ending Domain Validation
Sep 19 13:40:12 stp4-000 target1:0:2: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:40:12 stp4-000 SCSI device sdc: 35566480 512-byte hdwr sectors (18210 MB)
Sep 19 13:40:12 stp4-000 sdc: Write Protect is off
Sep 19 13:40:12 stp4-000 sdc: Mode Sense: a7 00 10 08
Sep 19 13:40:12 stp4-000 SCSI device sdc: drive cache: write back w/ FUA
Sep 19 13:40:12 stp4-000 SCSI device sdc: 35566480 512-byte hdwr sectors (18210 MB)
Sep 19 13:40:12 stp4-000 sdc: Write Protect is off
Sep 19 13:40:12 stp4-000 sdc: Mode Sense: a7 00 10 08
Sep 19 13:40:12 stp4-000 SCSI device sdc: drive cache: write back w/ FUA
Sep 19 13:40:12 stp4-000 sdc: unknown partition table
Sep 19 13:40:12 stp4-000 sd 1:0:2:0: Attached scsi disk sdc
Sep 19 13:40:12 stp4-000 sd 1:0:2:0: Attached scsi generic sg2 type 0
Sep 19 13:40:12 stp4-000 scsi 1:0:3:0: Direct access HP 18.2GB C 80-H008 H008 PQ: 0 ANSI: 2
Sep 19 13:40:12 stp4-000 target1:0:3: Beginning Domain Validation
Sep 19 13:40:12 stp4-000 target1:0:3: Ending Domain Validation
Sep 19 13:40:12 stp4-000 target1:0:3: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:40:12 stp4-000 SCSI device sdd: 35566480 512-byte hdwr sectors (18210 MB)
Sep 19 13:40:12 stp4-000 sdd: Write Protect is off
Sep 19 13:40:12 stp4-000 sdd: Mode Sense: a7 00 10 08
Sep 19 13:40:12 stp4-000 SCSI device sdd: drive cache: write back w/ FUA
Sep 19 13:40:12 stp4-000 SCSI device sdd: 35566480 512-byte hdwr sectors (18210 MB)
Sep 19 13:40:12 stp4-000 sdd: Write Protect is off
Sep 19 13:40:12 stp4-000 sdd: Mode Sense: a7 00 10 08
Sep 19 13:40:12 stp4-000 SCSI device sdd: drive cache: write back w/ FUA
Sep 19 13:40:12 stp4-000 sdd: unknown partition table
Sep 19 13:40:12 stp4-000 sd 1:0:3:0: Attached scsi disk sdd
Sep 19 13:40:12 stp4-000 sd 1:0:3:0: Attached scsi generic sg3 type 0
Sep 19 13:40:12 stp4-000 scsi 1:0:5:0: Processor HP D5989C 1.06 PQ: 0 ANSI: 2
Sep 19 13:40:12 stp4-000 target1:0:5: Beginning Domain Validation
Sep 19 13:40:12 stp4-000 target1:0:5: Ending Domain Validation
Sep 19 13:40:12 stp4-000 target1:0:5: asynchronous
Sep 19 13:40:12 stp4-000 scsi 1:0:5:0: Attached scsi generic sg4 type 3
Sep 19 13:40:13 stp4-000 scsi 1:0:8:0: Direct access HP 18.2G MAP3367NC#HJ HPC6 PQ: 0 ANSI: 3
Sep 19 13:40:13 stp4-000 target1:0:8: Beginning Domain Validation
Sep 19 13:40:23 stp4-000 mptscsih: ioc0: attempting task abort! (sc=f7f2d180)
Sep 19 13:40:23 stp4-000 scsi 1:0:8:0:
Sep 19 13:40:23 stp4-000 command: cdb[0]=0x12: 12 00 00 00 60 00
Sep 19 13:40:25 stp4-000 mptbase: Initiating ioc0 recovery
Sep 19 13:40:50 stp4-000 mptscsih: ioc0: task abort: SUCCESS (sc=f7f2d180)
Sep 19 13:40:50 stp4-000 target1:0:1: Beginning Domain Validation
Sep 19 13:40:50 stp4-000 target1:0:8: Domain Validation detected failure, dropping back
Sep 19 13:40:50 stp4-000 target1:0:8: Domain Validation skipping write tests
Sep 19 13:40:50 stp4-000 target1:0:8: Ending Domain Validation
Sep 19 13:40:50 stp4-000 target1:0:8: asynchronous
Sep 19 13:40:50 stp4-000 SCSI device sde: 35566480 512-byte hdwr sectors (18210 MB)
Sep 19 13:40:50 stp4-000 sde: Write Protect is off
Sep 19 13:40:50 stp4-000 sde: Mode Sense: cf 00 10 08
Sep 19 13:40:50 stp4-000 SCSI device sde: drive cache: write through w/ FUA
Sep 19 13:40:50 stp4-000 SCSI device sde: 35566480 512-byte hdwr sectors (18210 MB)
Sep 19 13:40:50 stp4-000 target1:0:1: Ending Domain Validation
Sep 19 13:40:50 stp4-000 target1:0:1: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:40:50 stp4-000 target1:0:2: Beginning Domain Validation
Sep 19 13:40:50 stp4-000 sde: Write Protect is off
Sep 19 13:40:50 stp4-000 sde: Mode Sense: cf 00 10 08
Sep 19 13:40:50 stp4-000 SCSI device sde: drive cache: write through w/ FUA
Sep 19 13:40:50 stp4-000 sde:<6> target1:0:2: Ending Domain Validation
Sep 19 13:40:50 stp4-000 target1:0:2: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:40:50 stp4-000 target1:0:3: Beginning Domain Validation
Sep 19 13:40:50 stp4-000 unknown partition table
Sep 19 13:40:50 stp4-000 sd 1:0:8:0: Attached scsi disk sde
Sep 19 13:40:50 stp4-000 sd 1:0:8:0: Attached scsi generic sg5 type 0
Sep 19 13:40:50 stp4-000 scsi 1:0:9:0: Direct access HP 18.2GB C 80-H008 H008 PQ: 0 ANSI: 2
Sep 19 13:40:50 stp4-000 target1:0:9: Beginning Domain Validation
Sep 19 13:40:50 stp4-000 target1:0:3: Ending Domain Validation
Sep 19 13:40:50 stp4-000 target1:0:3: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:40:50 stp4-000 target1:0:5: Beginning Domain Validation
Sep 19 13:40:50 stp4-000 target1:0:5: Ending Domain Validation
Sep 19 13:40:50 stp4-000 target1:0:5: asynchronous
Sep 19 13:40:50 stp4-000 target1:0:8: Beginning Domain Validation
Sep 19 13:40:50 stp4-000 target1:0:9: Ending Domain Validation
Sep 19 13:40:50 stp4-000 target1:0:9: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:40:50 stp4-000 SCSI device sdf: 35566480 512-byte hdwr sectors (18210 MB)
Sep 19 13:40:56 stp4-000 udevd-event[4719]: wait_for_sysfs: waiting for '/sys/devices/pci0000:01/0000:01:02.0/host1/target1:0:9/1:0:9:0/ioerr_cnt' failed
Sep 19 13:41:20 stp4-000 mptscsih: ioc0: attempting task abort! (sc=f6c981c0)
Sep 19 13:41:20 stp4-000 sd 1:0:8:0:
Sep 19 13:41:20 stp4-000 command: cdb[0]=0x12: 12 00 00 00 60 00
Sep 19 13:41:22 stp4-000 mptbase: Initiating ioc0 recovery
Sep 19 13:41:46 stp4-000 mptscsih: ioc0: task abort: SUCCESS (sc=f6c981c0)
Sep 19 13:41:46 stp4-000 target1:0:8: Domain Validation detected failure, dropping back
Sep 19 13:41:46 stp4-000 target1:0:8: Domain Validation skipping write tests
Sep 19 13:41:46 stp4-000 target1:0:8: Ending Domain Validation
Sep 19 13:41:46 stp4-000 target1:0:8: asynchronous
Sep 19 13:41:47 stp4-000 sdf: Write Protect is off
Sep 19 13:41:47 stp4-000 sdf: Mode Sense: a7 00 10 08
Sep 19 13:41:47 stp4-000 SCSI device sdf: drive cache: write back w/ FUA
Sep 19 13:41:47 stp4-000 SCSI device sdf: 35566480 512-byte hdwr sectors (18210 MB)
Sep 19 13:41:47 stp4-000 sdf: Write Protect is off
Sep 19 13:41:47 stp4-000 sdf: Mode Sense: a7 00 10 08
Sep 19 13:41:47 stp4-000 SCSI device sdf: drive cache: write back w/ FUA
Sep 19 13:41:47 stp4-000 sdf:<6> target1:0:9: Beginning Domain Validation
Sep 19 13:41:47 stp4-000 target1:0:9: Ending Domain Validation
Sep 19 13:41:47 stp4-000 target1:0:9: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:41:47 stp4-000 target1:0:1: Beginning Domain Validation
Sep 19 13:41:47 stp4-000 unknown partition table
Sep 19 13:41:47 stp4-000 sd 1:0:9:0: Attached scsi disk sdf
Sep 19 13:41:47 stp4-000 sd 1:0:9:0: Attached scsi generic sg6 type 0
Sep 19 13:41:47 stp4-000 scsi 1:0:10:0: Direct access HP 18.2GB C 80-H008 H008 PQ: 0 ANSI: 2
Sep 19 13:41:47 stp4-000 target1:0:10: Beginning Domain Validation
Sep 19 13:41:47 stp4-000 target1:0:1: Ending Domain Validation
Sep 19 13:41:47 stp4-000 target1:0:1: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:41:47 stp4-000 target1:0:2: Beginning Domain Validation
Sep 19 13:41:47 stp4-000 target1:0:10: Ending Domain Validation
Sep 19 13:41:47 stp4-000 target1:0:10: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:41:47 stp4-000 SCSI device sdg: 35566480 512-byte hdwr sectors (18210 MB)
Sep 19 13:41:47 stp4-000 target1:0:2: Ending Domain Validation
Sep 19 13:41:47 stp4-000 target1:0:2: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:41:47 stp4-000 target1:0:3: Beginning Domain Validation
Sep 19 13:41:47 stp4-000 target1:0:3: Ending Domain Validation
Sep 19 13:41:47 stp4-000 target1:0:3: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:41:47 stp4-000 target1:0:5: Beginning Domain Validation
Sep 19 13:41:47 stp4-000 target1:0:5: Ending Domain Validation
Sep 19 13:41:47 stp4-000 target1:0:5: asynchronous
Sep 19 13:41:47 stp4-000 target1:0:8: Beginning Domain Validation
Sep 19 13:41:47 stp4-000 sdg: Write Protect is off
Sep 19 13:41:47 stp4-000 sdg: Mode Sense: a7 00 10 08
Sep 19 13:41:47 stp4-000 SCSI device sdg: drive cache: write through w/ FUA
Sep 19 13:41:47 stp4-000 SCSI device sdg: 35566480 512-byte hdwr sectors (18210 MB)
Sep 19 13:41:47 stp4-000 sdg: Write Protect is off
Sep 19 13:41:47 stp4-000 sdg: Mode Sense: a7 00 10 08
Sep 19 13:41:51 stp4-000 udevd-event[4725]: wait_for_sysfs: waiting for '/sys/devices/pci0000:01/0000:01:02.0/host1/target1:0:10/1:0:10:0/ioerr_cnt' failedSep 19 13:42:17 stp4-000 mptscsih: ioc0: attempting task abort! (sc=f7f2d180)
Sep 19 13:42:17 stp4-000 sd 1:0:8:0:
Sep 19 13:42:17 stp4-000 command: cdb[0]=0x12: 12 00 00 00 60 00
Sep 19 13:42:19 stp4-000 mptbase: Initiating ioc0 recovery
Sep 19 13:42:44 stp4-000 mptscsih: ioc0: task abort: SUCCESS (sc=f7f2d180)
Sep 19 13:42:44 stp4-000 target1:0:8: Domain Validation detected failure, dropping back
Sep 19 13:42:44 stp4-000 target1:0:8: Domain Validation skipping write tests
Sep 19 13:42:44 stp4-000 target1:0:8: Ending Domain Validation
Sep 19 13:42:44 stp4-000 target1:0:8: asynchronous
Sep 19 13:42:44 stp4-000 target1:0:9: Beginning Domain Validation
Sep 19 13:42:44 stp4-000 target1:0:9: Ending Domain Validation
Sep 19 13:42:44 stp4-000 target1:0:9: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:42:44 stp4-000 SCSI device sdg: drive cache: write through w/ FUA
Sep 19 13:42:44 stp4-000 sdg:<6> target1:0:10: Beginning Domain Validation
Sep 19 13:42:44 stp4-000 target1:0:10: Ending Domain Validation
Sep 19 13:42:44 stp4-000 target1:0:10: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:42:44 stp4-000 target1:0:1: Beginning Domain Validation
Sep 19 13:42:44 stp4-000 unknown partition table
Sep 19 13:42:44 stp4-000 sd 1:0:10:0: Attached scsi disk sdg
Sep 19 13:42:44 stp4-000 sd 1:0:10:0: Attached scsi generic sg7 type 0
Sep 19 13:42:44 stp4-000 scsi 1:0:11:0: Direct access HP 18.2GB C 80-H008 H008 PQ: 0 ANSI: 2
Sep 19 13:42:44 stp4-000 target1:0:11: Beginning Domain Validation
Sep 19 13:42:44 stp4-000 target1:0:1: Ending Domain Validation
Sep 19 13:42:44 stp4-000 target1:0:1: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:42:44 stp4-000 target1:0:2: Beginning Domain Validation
Sep 19 13:42:44 stp4-000 target1:0:11: Ending Domain Validation
Sep 19 13:42:44 stp4-000 target1:0:11: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:42:44 stp4-000 SCSI device sdh: 35566480 512-byte hdwr sectors (18210 MB)
Sep 19 13:42:44 stp4-000 target1:0:2: Ending Domain Validation
Sep 19 13:42:44 stp4-000 target1:0:2: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:42:44 stp4-000 target1:0:3: Beginning Domain Validation
Sep 19 13:42:44 stp4-000 target1:0:3: Ending Domain Validation
Sep 19 13:42:44 stp4-000 target1:0:3: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:42:44 stp4-000 target1:0:5: Beginning Domain Validation
Sep 19 13:42:44 stp4-000 sdh: Write Protect is off
Sep 19 13:42:44 stp4-000 sdh: Mode Sense: a7 00 10 08
Sep 19 13:42:44 stp4-000 target1:0:5: Ending Domain Validation
Sep 19 13:42:44 stp4-000 target1:0:5: asynchronous
Sep 19 13:42:44 stp4-000 target1:0:8: Beginning Domain Validation
Sep 19 13:42:44 stp4-000 SCSI device sdh: drive cache: write back w/ FUA
Sep 19 13:42:44 stp4-000 SCSI device sdh: 35566480 512-byte hdwr sectors (18210 MB)
Sep 19 13:42:44 stp4-000 sdh: Write Protect is off
Sep 19 13:42:44 stp4-000 sdh: Mode Sense: a7 00 10 08
Sep 19 13:42:50 stp4-000 udevd-event[4731]: wait_for_sysfs: waiting for '/sys/devices/pci0000:01/0000:01:02.0/host1/target1:0:11/1:0:11:0/ioerr_cnt' failedSep 19 13:43:14 stp4-000 mptscsih: ioc0: attempting task abort! (sc=f7f2d180)
Sep 19 13:43:14 stp4-000 sd 1:0:8:0:
Sep 19 13:43:14 stp4-000 command: cdb[0]=0x12: 12 00 00 00 60 00
Sep 19 13:43:16 stp4-000 mptbase: Initiating ioc0 recovery
Sep 19 13:43:41 stp4-000 mptscsih: ioc0: task abort: SUCCESS (sc=f7f2d180)
Sep 19 13:43:41 stp4-000 target1:0:8: Domain Validation detected failure, dropping back
Sep 19 13:43:41 stp4-000 target1:0:8: Domain Validation skipping write tests
Sep 19 13:43:41 stp4-000 target1:0:8: Ending Domain Validation
Sep 19 13:43:41 stp4-000 target1:0:8: asynchronous
Sep 19 13:43:41 stp4-000 target1:0:9: Beginning Domain Validation
Sep 19 13:43:41 stp4-000 target1:0:9: Ending Domain Validation
Sep 19 13:43:41 stp4-000 target1:0:9: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:43:41 stp4-000 target1:0:10: Beginning Domain Validation
Sep 19 13:43:41 stp4-000 SCSI device sdh: drive cache: write back w/ FUA
Sep 19 13:43:41 stp4-000 sdh: unknown partition table
Sep 19 13:43:41 stp4-000 sd 1:0:11:0: Attached scsi disk sdh
Sep 19 13:43:41 stp4-000 sd 1:0:11:0: Attached scsi generic sg8 type 0
Sep 19 13:43:41 stp4-000 target1:0:10: Ending Domain Validation
Sep 19 13:43:41 stp4-000 target1:0:10: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:43:41 stp4-000 target1:0:11: Beginning Domain Validation
Sep 19 13:43:41 stp4-000 scsi 1:0:12:0: Direct access HP 18.2GB C 80-H008 H008 PQ: 0 ANSI: 2
Sep 19 13:43:41 stp4-000 target1:0:12: Beginning Domain Validation
Sep 19 13:43:41 stp4-000 target1:0:11: Ending Domain Validation
Sep 19 13:43:41 stp4-000 target1:0:11: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:43:41 stp4-000 target1:0:12: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:43:41 stp4-000 target1:0:1: Beginning Domain Validation
Sep 19 13:43:41 stp4-000 target1:0:12: Ending Domain Validation
Sep 19 13:43:41 stp4-000 target1:0:12: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:43:41 stp4-000 SCSI device sdi: 35566480 512-byte hdwr sectors (18210 MB)
Sep 19 13:43:41 stp4-000 target1:0:1: Ending Domain Validation
Sep 19 13:43:41 stp4-000 target1:0:1: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:43:41 stp4-000 target1:0:2: Beginning Domain Validation
Sep 19 13:43:41 stp4-000 target1:0:2: Ending Domain Validation
Sep 19 13:43:41 stp4-000 target1:0:2: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:43:41 stp4-000 target1:0:3: Beginning Domain Validation
Sep 19 13:43:41 stp4-000 target1:0:3: Ending Domain Validation
Sep 19 13:43:41 stp4-000 target1:0:3: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:43:41 stp4-000 target1:0:5: Beginning Domain Validation
Sep 19 13:43:41 stp4-000 sdi: Write Protect is off
Sep 19 13:43:41 stp4-000 sdi: Mode Sense: a7 00 10 08
Sep 19 13:43:41 stp4-000 target1:0:5: Ending Domain Validation
Sep 19 13:43:41 stp4-000 target1:0:5: asynchronous
Sep 19 13:43:41 stp4-000 target1:0:8: Beginning Domain Validation
Sep 19 13:43:41 stp4-000 SCSI device sdi: drive cache: write back w/ FUA
Sep 19 13:43:41 stp4-000 SCSI device sdi: 35566480 512-byte hdwr sectors (18210 MB)
Sep 19 13:43:41 stp4-000 sdi: Write Protect is off
Sep 19 13:43:41 stp4-000 sdi: Mode Sense: a7 00 10 08
Sep 19 13:43:41 stp4-000 SCSI device sdi: drive cache: write back w/ FUA
Sep 19 13:43:45 stp4-000 udevd-event[4737]: wait_for_sysfs: waiting for '/sys/devices/pci0000:01/0000:01:02.0/host1/target1:0:12/1:0:12:0/ioerr_cnt' failedSep 19 13:44:11 stp4-000 sdi:<4>mptscsih: ioc0: attempting task abort! (sc=f6c981c0)
Sep 19 13:44:11 stp4-000 sd 1:0:8:0:
Sep 19 13:44:11 stp4-000 command: cdb[0]=0x12: 12 00 00 00 60 00
Sep 19 13:44:13 stp4-000 mptbase: Initiating ioc0 recovery
Sep 19 13:44:38 stp4-000 mptscsih: ioc0: task abort: SUCCESS (sc=f6c981c0)
Sep 19 13:44:38 stp4-000 target1:0:8: Domain Validation detected failure, dropping back
Sep 19 13:44:38 stp4-000 target1:0:8: Domain Validation skipping write tests
Sep 19 13:44:38 stp4-000 target1:0:8: Ending Domain Validation
Sep 19 13:44:38 stp4-000 target1:0:8: asynchronous
Sep 19 13:44:38 stp4-000 target1:0:9: Beginning Domain Validation
Sep 19 13:44:38 stp4-000 sdi1
Sep 19 13:44:38 stp4-000 sd 1:0:12:0: Attached scsi disk sdi
Sep 19 13:44:38 stp4-000 sd 1:0:12:0: Attached scsi generic sg9 type 0
Sep 19 13:44:38 stp4-000 scsi 1:0:13:0: Direct access HP 18.2GB C 80-H008 H008 PQ: 0 ANSI: 2
Sep 19 13:44:38 stp4-000 target1:0:13: Beginning Domain Validation
Sep 19 13:44:38 stp4-000 target1:0:9: Ending Domain Validation
Sep 19 13:44:38 stp4-000 target1:0:9: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:44:38 stp4-000 target1:0:10: Beginning Domain Validation
Sep 19 13:44:38 stp4-000 target1:0:13: Ending Domain Validation
Sep 19 13:44:38 stp4-000 target1:0:13: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:44:38 stp4-000 SCSI device sdj: 35566480 512-byte hdwr sectors (18210 MB)
Sep 19 13:44:38 stp4-000 target1:0:10: Ending Domain Validation
Sep 19 13:44:38 stp4-000 target1:0:10: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:44:38 stp4-000 target1:0:11: Beginning Domain Validation
Sep 19 13:44:38 stp4-000 target1:0:11: Ending Domain Validation
Sep 19 13:44:38 stp4-000 target1:0:11: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:44:38 stp4-000 target1:0:12: Beginning Domain Validation
Sep 19 13:44:38 stp4-000 sdj: Write Protect is off
Sep 19 13:44:38 stp4-000 sdj: Mode Sense: a7 00 10 08
Sep 19 13:44:38 stp4-000 target1:0:12: Ending Domain Validation
Sep 19 13:44:38 stp4-000 target1:0:12: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:44:38 stp4-000 SCSI device sdj: drive cache: write back w/ FUA
Sep 19 13:44:38 stp4-000 SCSI device sdj: 35566480 512-byte hdwr sectors (18210 MB)
Sep 19 13:44:38 stp4-000 sdj: Write Protect is off
Sep 19 13:44:38 stp4-000 sdj: Mode Sense: a7 00 10 08
Sep 19 13:44:38 stp4-000 SCSI device sdj: drive cache: write back w/ FUA
Sep 19 13:44:38 stp4-000 sdj:<6> target1:0:13: Beginning Domain Validation
Sep 19 13:44:38 stp4-000 target1:0:13: Ending Domain Validation
Sep 19 13:44:38 stp4-000 target1:0:13: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:44:38 stp4-000 target1:0:1: Beginning Domain Validation
Sep 19 13:44:38 stp4-000 unknown partition table
Sep 19 13:44:38 stp4-000 sd 1:0:13:0: Attached scsi disk sdj
Sep 19 13:44:38 stp4-000 sd 1:0:13:0: Attached scsi generic sg10 type 0
Sep 19 13:44:38 stp4-000 scsi 1:0:14:0: Direct access HP 18.2GB C 80-H008 H008 PQ: 0 ANSI: 2
Sep 19 13:44:38 stp4-000 target1:0:14: Beginning Domain Validation
Sep 19 13:44:38 stp4-000 target1:0:1: Ending Domain Validation
Sep 19 13:44:38 stp4-000 target1:0:1: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:44:38 stp4-000 target1:0:2: Beginning Domain Validation
Sep 19 13:44:38 stp4-000 target1:0:14: Ending Domain Validation
Sep 19 13:44:38 stp4-000 target1:0:14: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:44:38 stp4-000 SCSI device sdk: 35566480 512-byte hdwr sectors (18210 MB)
Sep 19 13:44:38 stp4-000 target1:0:2: Ending Domain Validation
Sep 19 13:44:38 stp4-000 target1:0:2: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:44:38 stp4-000 target1:0:3: Beginning Domain Validation
Sep 19 13:44:38 stp4-000 target1:0:3: Ending Domain Validation
Sep 19 13:44:38 stp4-000 target1:0:3: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:44:38 stp4-000 target1:0:5: Beginning Domain Validation
Sep 19 13:44:38 stp4-000 sdk: Write Protect is off
Sep 19 13:44:38 stp4-000 sdk: Mode Sense: a7 00 10 08
Sep 19 13:44:38 stp4-000 target1:0:5: Ending Domain Validation
Sep 19 13:44:38 stp4-000 target1:0:5: asynchronous
Sep 19 13:44:38 stp4-000 target1:0:8: Beginning Domain Validation
Sep 19 13:44:38 stp4-000 SCSI device sdk: drive cache: write back w/ FUA
Sep 19 13:44:38 stp4-000 SCSI device sdk: 35566480 512-byte hdwr sectors (18210 MB)
Sep 19 13:44:38 stp4-000 sdk: Write Protect is off
Sep 19 13:44:38 stp4-000 sdk: Mode Sense: a7 00 10 08
Sep 19 13:44:44 stp4-000 udevd-event[4752]: wait_for_sysfs: waiting for '/sys/devices/pci0000:01/0000:01:02.0/host1/target1:0:14/1:0:14:0/ioerr_cnt' failedSep 19 13:45:08 stp4-000 mptscsih: ioc0: attempting task abort! (sc=f6c981c0)
Sep 19 13:45:08 stp4-000 sd 1:0:8:0:
Sep 19 13:45:08 stp4-000 command: cdb[0]=0x12: 12 00 00 00 60 00
Sep 19 13:45:10 stp4-000 mptbase: Initiating ioc0 recovery
Sep 19 13:45:35 stp4-000 mptscsih: ioc0: task abort: SUCCESS (sc=f6c981c0)
Sep 19 13:45:35 stp4-000 target1:0:8: Domain Validation detected failure, dropping back
Sep 19 13:45:35 stp4-000 target1:0:8: Domain Validation skipping write tests
Sep 19 13:45:35 stp4-000 target1:0:8: Ending Domain Validation
Sep 19 13:45:35 stp4-000 target1:0:8: asynchronous
Sep 19 13:45:35 stp4-000 target1:0:9: Beginning Domain Validation
Sep 19 13:45:35 stp4-000 target1:0:9: Ending Domain Validation
Sep 19 13:45:35 stp4-000 target1:0:9: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:45:35 stp4-000 target1:0:10: Beginning Domain Validation
Sep 19 13:45:35 stp4-000 SCSI device sdk: drive cache: write back w/ FUA
Sep 19 13:45:35 stp4-000 sdk: sdk1
Sep 19 13:45:35 stp4-000 sd 1:0:14:0: Attached scsi disk sdk
Sep 19 13:45:35 stp4-000 sd 1:0:14:0: Attached scsi generic sg11 type 0
Sep 19 13:45:35 stp4-000 target1:0:10: Ending Domain Validation
Sep 19 13:45:35 stp4-000 target1:0:10: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:45:35 stp4-000 target1:0:11: Beginning Domain Validation
Sep 19 13:45:35 stp4-000 scsi 1:0:15:0: Direct access HP 18.2GB C 80-H008 H008 PQ: 0 ANSI: 2
Sep 19 13:45:35 stp4-000 target1:0:15: Beginning Domain Validation
Sep 19 13:45:35 stp4-000 target1:0:11: Ending Domain Validation
Sep 19 13:45:35 stp4-000 target1:0:11: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:45:35 stp4-000 target1:0:12: Beginning Domain Validation
Sep 19 13:45:35 stp4-000 target1:0:15: Ending Domain Validation
Sep 19 13:45:35 stp4-000 target1:0:15: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:45:35 stp4-000 SCSI device sdl: 35566480 512-byte hdwr sectors (18210 MB)
Sep 19 13:45:35 stp4-000 target1:0:12: Ending Domain Validation
Sep 19 13:45:35 stp4-000 target1:0:12: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:45:35 stp4-000 target1:0:13: Beginning Domain Validation
Sep 19 13:45:35 stp4-000 target1:0:13: Ending Domain Validation
Sep 19 13:45:35 stp4-000 target1:0:13: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:45:35 stp4-000 target1:0:14: Beginning Domain Validation
Sep 19 13:45:35 stp4-000 sdl: Write Protect is off
Sep 19 13:45:35 stp4-000 sdl: Mode Sense: a7 00 10 08
Sep 19 13:45:35 stp4-000 SCSI device sdl: drive cache: write through w/ FUA
Sep 19 13:45:35 stp4-000 SCSI device sdl: 35566480 512-byte hdwr sectors (18210 MB)
Sep 19 13:45:35 stp4-000 target1:0:14: Ending Domain Validation
Sep 19 13:45:35 stp4-000 target1:0:14: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:45:35 stp4-000 sdl: Write Protect is off
Sep 19 13:45:35 stp4-000 sdl: Mode Sense: a7 00 10 08
Sep 19 13:45:35 stp4-000 SCSI device sdl: drive cache: write through w/ FUA
Sep 19 13:45:35 stp4-000 sdl:<6> target1:0:15: Beginning Domain Validation
Sep 19 13:45:35 stp4-000 target1:0:15: Ending Domain Validation
Sep 19 13:45:35 stp4-000 target1:0:15: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:45:35 stp4-000 target1:0:1: Beginning Domain Validation
Sep 19 13:45:35 stp4-000 unknown partition table
Sep 19 13:45:35 stp4-000 sd 1:0:15:0: Attached scsi disk sdl
Sep 19 13:45:35 stp4-000 sd 1:0:15:0: Attached scsi generic sg12 type 0
Sep 19 13:45:35 stp4-000 mptbase: Initiating ioc1 bringup
Sep 19 13:45:36 stp4-000 ioc1: 53C1030: Capabilities={Initiator}
Sep 19 13:45:37 stp4-000 scsi2 : ioc1: LSI53C1030, FwRev=01030a00h, Ports=1, MaxQ=222, IRQ=21
Sep 19 13:45:37 stp4-000 target1:0:1: Ending Domain Validation
Sep 19 13:45:37 stp4-000 target1:0:1: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:45:37 stp4-000 target1:0:2: Beginning Domain Validation
Sep 19 13:45:37 stp4-000 target1:0:2: Ending Domain Validation
Sep 19 13:45:37 stp4-000 target1:0:2: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:45:37 stp4-000 target1:0:3: Beginning Domain Validation
Sep 19 13:45:37 stp4-000 target1:0:3: Ending Domain Validation
Sep 19 13:45:37 stp4-000 target1:0:3: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:45:37 stp4-000 target1:0:5: Beginning Domain Validation
Sep 19 13:45:37 stp4-000 target1:0:5: Ending Domain Validation
Sep 19 13:45:37 stp4-000 target1:0:5: asynchronous
Sep 19 13:45:37 stp4-000 target1:0:8: Beginning Domain Validation
Sep 19 13:45:47 stp4-000 mptscsih: ioc0: attempting task abort! (sc=f6c981c0)
Sep 19 13:45:47 stp4-000 sd 1:0:8:0:
Sep 19 13:45:47 stp4-000 command: cdb[0]=0x12: 12 00 00 00 60 00
Sep 19 13:45:50 stp4-000 mptbase: Initiating ioc0 recovery
Sep 19 13:46:16 stp4-000 mptscsih: ioc0: task abort: SUCCESS (sc=f6c981c0)
Sep 19 13:46:16 stp4-000 target1:0:8: Domain Validation detected failure, dropping back
Sep 19 13:46:16 stp4-000 target1:0:8: Domain Validation skipping write tests
Sep 19 13:46:16 stp4-000 target1:0:8: Ending Domain Validation
Sep 19 13:46:16 stp4-000 target1:0:8: asynchronous
Sep 19 13:46:16 stp4-000 target1:0:9: Beginning Domain Validation
Sep 19 13:46:16 stp4-000 target1:0:9: Ending Domain Validation
Sep 19 13:46:16 stp4-000 target1:0:9: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:46:16 stp4-000 target1:0:10: Beginning Domain Validation
Sep 19 13:46:16 stp4-000 target1:0:10: Ending Domain Validation
Sep 19 13:46:16 stp4-000 target1:0:10: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:46:16 stp4-000 target1:0:11: Beginning Domain Validation
Sep 19 13:46:16 stp4-000 target1:0:11: Ending Domain Validation
Sep 19 13:46:16 stp4-000 target1:0:11: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:46:16 stp4-000 target1:0:12: Beginning Domain Validation
Sep 19 13:46:16 stp4-000 target1:0:12: Ending Domain Validation
Sep 19 13:46:16 stp4-000 target1:0:12: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:46:16 stp4-000 target1:0:13: Beginning Domain Validation
Sep 19 13:46:16 stp4-000 target1:0:13: Ending Domain Validation
Sep 19 13:46:16 stp4-000 target1:0:13: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:46:16 stp4-000 target1:0:14: Beginning Domain Validation
Sep 19 13:46:16 stp4-000 target1:0:14: Ending Domain Validation
Sep 19 13:46:16 stp4-000 target1:0:14: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:46:16 stp4-000 target1:0:15: Beginning Domain Validation
Sep 19 13:46:16 stp4-000 target1:0:15: Ending Domain Validation
Sep 19 13:46:16 stp4-000 target1:0:15: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:46:16 stp4-000 target1:0:1: Beginning Domain Validation
Sep 19 13:46:16 stp4-000 target1:0:1: Ending Domain Validation
Sep 19 13:46:16 stp4-000 target1:0:1: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:46:16 stp4-000 target1:0:2: Beginning Domain Validation
Sep 19 13:46:16 stp4-000 target1:0:2: Ending Domain Validation
Sep 19 13:46:16 stp4-000 target1:0:2: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:46:16 stp4-000 target1:0:3: Beginning Domain Validation
Sep 19 13:46:16 stp4-000 target1:0:3: Ending Domain Validation
Sep 19 13:46:16 stp4-000 target1:0:3: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:46:16 stp4-000 target1:0:5: Beginning Domain Validation
Sep 19 13:46:16 stp4-000 target1:0:5: Ending Domain Validation
Sep 19 13:46:16 stp4-000 target1:0:5: asynchronous
Sep 19 13:46:16 stp4-000 target1:0:8: Beginning Domain Validation
Sep 19 13:46:26 stp4-000 mptscsih: ioc0: attempting task abort! (sc=f6c981c0)
Sep 19 13:46:26 stp4-000 sd 1:0:8:0:
Sep 19 13:46:26 stp4-000 command: cdb[0]=0x12: 12 00 00 00 60 00
Sep 19 13:46:28 stp4-000 mptbase: Initiating ioc0 recovery
Sep 19 13:46:54 stp4-000 mptscsih: ioc0: task abort: SUCCESS (sc=f6c981c0)
Sep 19 13:46:54 stp4-000 target1:0:8: Domain Validation detected failure, dropping back
Sep 19 13:46:54 stp4-000 target1:0:8: Domain Validation skipping write tests
Sep 19 13:46:54 stp4-000 target1:0:8: Ending Domain Validation
Sep 19 13:46:54 stp4-000 target1:0:8: asynchronous
Sep 19 13:46:54 stp4-000 target1:0:9: Beginning Domain Validation
Sep 19 13:46:54 stp4-000 target1:0:9: Ending Domain Validation
Sep 19 13:46:54 stp4-000 target1:0:9: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:46:54 stp4-000 target1:0:10: Beginning Domain Validation
Sep 19 13:46:54 stp4-000 target1:0:10: Ending Domain Validation
Sep 19 13:46:54 stp4-000 target1:0:10: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:46:54 stp4-000 target1:0:11: Beginning Domain Validation
Sep 19 13:46:54 stp4-000 target1:0:11: Ending Domain Validation
Sep 19 13:46:54 stp4-000 target1:0:11: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:46:54 stp4-000 target1:0:12: Beginning Domain Validation
Sep 19 13:46:54 stp4-000 target1:0:12: Ending Domain Validation
Sep 19 13:46:54 stp4-000 target1:0:12: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:46:54 stp4-000 target1:0:13: Beginning Domain Validation
Sep 19 13:46:54 stp4-000 target1:0:13: Ending Domain Validation
Sep 19 13:46:54 stp4-000 target1:0:13: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:46:54 stp4-000 target1:0:14: Beginning Domain Validation
Sep 19 13:46:54 stp4-000 target1:0:14: Ending Domain Validation
Sep 19 13:46:54 stp4-000 target1:0:14: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:46:54 stp4-000 target1:0:15: Beginning Domain Validation
Sep 19 13:46:54 stp4-000 target1:0:15: Ending Domain Validation
Sep 19 13:46:54 stp4-000 target1:0:15: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:46:54 stp4-000 target1:0:1: Beginning Domain Validation
Sep 19 13:46:54 stp4-000 target1:0:1: Ending Domain Validation
Sep 19 13:46:54 stp4-000 target1:0:1: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:46:54 stp4-000 target1:0:2: Beginning Domain Validation
Sep 19 13:46:54 stp4-000 target1:0:2: Ending Domain Validation
Sep 19 13:46:54 stp4-000 target1:0:2: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:46:54 stp4-000 target1:0:3: Beginning Domain Validation
Sep 19 13:46:54 stp4-000 target1:0:3: Ending Domain Validation
Sep 19 13:46:54 stp4-000 target1:0:3: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:46:54 stp4-000 target1:0:5: Beginning Domain Validation
Sep 19 13:46:54 stp4-000 target1:0:5: Ending Domain Validation
Sep 19 13:46:54 stp4-000 target1:0:5: asynchronous
Sep 19 13:46:54 stp4-000 target1:0:8: Beginning Domain Validation
Sep 19 13:47:04 stp4-000 mptscsih: ioc0: attempting task abort! (sc=f6c981c0)
Sep 19 13:47:04 stp4-000 sd 1:0:8:0:
Sep 19 13:47:04 stp4-000 command: cdb[0]=0x12: 12 00 00 00 60 00
Sep 19 13:47:07 stp4-000 mptbase: Initiating ioc0 recovery
Sep 19 13:47:33 stp4-000 mptscsih: ioc0: task abort: SUCCESS (sc=f6c981c0)
Sep 19 13:47:33 stp4-000 target1:0:8: Domain Validation detected failure, dropping back
Sep 19 13:47:33 stp4-000 target1:0:8: Domain Validation skipping write tests
Sep 19 13:47:33 stp4-000 target1:0:8: Ending Domain Validation
Sep 19 13:47:33 stp4-000 target1:0:8: asynchronous
Sep 19 13:47:33 stp4-000 target1:0:9: Beginning Domain Validation
Sep 19 13:47:33 stp4-000 target1:0:9: Ending Domain Validation
Sep 19 13:47:33 stp4-000 target1:0:9: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:47:33 stp4-000 target1:0:10: Beginning Domain Validation
Sep 19 13:47:33 stp4-000 target1:0:10: Ending Domain Validation
Sep 19 13:47:33 stp4-000 target1:0:10: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:47:33 stp4-000 target1:0:11: Beginning Domain Validation
Sep 19 13:47:33 stp4-000 target1:0:11: Ending Domain Validation
Sep 19 13:47:33 stp4-000 target1:0:11: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:47:33 stp4-000 target1:0:12: Beginning Domain Validation
Sep 19 13:47:33 stp4-000 target1:0:12: Ending Domain Validation
Sep 19 13:47:33 stp4-000 target1:0:12: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:47:33 stp4-000 target1:0:13: Beginning Domain Validation
Sep 19 13:47:33 stp4-000 target1:0:13: Ending Domain Validation
Sep 19 13:47:33 stp4-000 target1:0:13: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:47:33 stp4-000 target1:0:14: Beginning Domain Validation
Sep 19 13:47:33 stp4-000 target1:0:14: Ending Domain Validation
Sep 19 13:47:33 stp4-000 target1:0:14: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:47:33 stp4-000 target1:0:15: Beginning Domain Validation
Sep 19 13:47:33 stp4-000 target1:0:15: Ending Domain Validation
Sep 19 13:47:33 stp4-000 target1:0:15: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:47:33 stp4-000 target1:0:1: Beginning Domain Validation
Sep 19 13:47:33 stp4-000 target1:0:1: Ending Domain Validation
Sep 19 13:47:33 stp4-000 target1:0:1: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:47:33 stp4-000 target1:0:2: Beginning Domain Validation
Sep 19 13:47:33 stp4-000 target1:0:2: Ending Domain Validation
Sep 19 13:47:33 stp4-000 target1:0:2: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:47:33 stp4-000 target1:0:3: Beginning Domain Validation
Sep 19 13:47:33 stp4-000 target1:0:3: Ending Domain Validation
Sep 19 13:47:33 stp4-000 target1:0:3: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:47:33 stp4-000 target1:0:5: Beginning Domain Validation
Sep 19 13:47:33 stp4-000 target1:0:5: Ending Domain Validation
Sep 19 13:47:33 stp4-000 target1:0:5: asynchronous
Sep 19 13:47:33 stp4-000 target1:0:8: Beginning Domain Validation
Sep 19 13:47:43 stp4-000 mptscsih: ioc0: attempting task abort! (sc=f6c981c0)
Sep 19 13:47:43 stp4-000 sd 1:0:8:0:
Sep 19 13:47:43 stp4-000 command: cdb[0]=0x12: 12 00 00 00 60 00
Sep 19 13:47:45 stp4-000 mptbase: Initiating ioc0 recovery
Sep 19 13:48:11 stp4-000 mptscsih: ioc0: task abort: SUCCESS (sc=f6c981c0)
Sep 19 13:48:11 stp4-000 target1:0:8: Domain Validation detected failure, dropping back
Sep 19 13:48:11 stp4-000 target1:0:8: Domain Validation skipping write tests
Sep 19 13:48:11 stp4-000 target1:0:8: Ending Domain Validation
Sep 19 13:48:11 stp4-000 target1:0:8: asynchronous
Sep 19 13:48:11 stp4-000 target1:0:9: Beginning Domain Validation
Sep 19 13:48:11 stp4-000 target1:0:9: Ending Domain Validation
Sep 19 13:48:11 stp4-000 target1:0:9: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:48:11 stp4-000 target1:0:10: Beginning Domain Validation
Sep 19 13:48:11 stp4-000 target1:0:10: Ending Domain Validation
Sep 19 13:48:11 stp4-000 target1:0:10: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:48:11 stp4-000 target1:0:11: Beginning Domain Validation
Sep 19 13:48:11 stp4-000 target1:0:11: Ending Domain Validation
Sep 19 13:48:11 stp4-000 target1:0:11: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:48:11 stp4-000 target1:0:12: Beginning Domain Validation
Sep 19 13:48:11 stp4-000 target1:0:12: Ending Domain Validation
Sep 19 13:48:11 stp4-000 target1:0:12: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:48:11 stp4-000 target1:0:13: Beginning Domain Validation
Sep 19 13:48:11 stp4-000 target1:0:13: Ending Domain Validation
Sep 19 13:48:11 stp4-000 target1:0:13: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:48:11 stp4-000 target1:0:14: Beginning Domain Validation
Sep 19 13:48:11 stp4-000 target1:0:14: Ending Domain Validation
Sep 19 13:48:11 stp4-000 target1:0:14: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:48:11 stp4-000 target1:0:15: Beginning Domain Validation
Sep 19 13:48:11 stp4-000 target1:0:15: Ending Domain Validation
Sep 19 13:48:11 stp4-000 target1:0:15: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:48:11 stp4-000 target1:0:1: Beginning Domain Validation
Sep 19 13:48:11 stp4-000 target1:0:1: Ending Domain Validation
Sep 19 13:48:11 stp4-000 target1:0:1: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:48:11 stp4-000 target1:0:2: Beginning Domain Validation
Sep 19 13:48:11 stp4-000 target1:0:2: Ending Domain Validation
Sep 19 13:48:11 stp4-000 target1:0:2: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:48:11 stp4-000 target1:0:3: Beginning Domain Validation
Sep 19 13:48:11 stp4-000 target1:0:3: Ending Domain Validation
Sep 19 13:48:11 stp4-000 target1:0:3: FAST-80 WIDE SCSI 160.0 MB/s DT RTI WRFLOW PCOMP (12.5 ns, offset 126)
Sep 19 13:48:11 stp4-000 target1:0:5: Beginning Domain Validation
Sep 19 13:48:11 stp4-000 target1:0:5: Ending Domain Validation
Sep 19 13:48:11 stp4-000 target1:0:5: asynchronous
Sep 19 13:48:11 stp4-000 target1:0:8: Beginning Domain Validation
Sep 19 13:48:21 stp4-000 mptscsih: ioc0: attempting task abort! (sc=f6c981c0)
Sep 19 13:48:21 stp4-000 sd 1:0:8:0:
Sep 19 13:48:21 stp4-000 command: cdb[0]=0x12: 12 00 00 00 60 00
Sep 19 13:48:24 stp4-000 mptbase: Initiating ioc0 recoveryQuoted 48 lines
James
drivers/scsi/scsi_transport_spi.c +7
-1@@ -47,6 +47,7 @@ #define DV_RETRIES 3 /* should only need/* Private data accessors (keep these out of the header file) */ #define spi_dv_pending (x) (((struct spi_transport_attrs *)&(x)->starget_data)->dv_pending) +#define spi_dv_in_progress (x) (((struct spi_transport_attrs *)&(x)->starget_data)->dv_in_progress)#define spi_dv_mutex (x) (((struct spi_transport_attrs *)&(x)->starget_data)->dv_mutex)struct spi_internal {@@ -240,6 +241,7 @@ static int spi_setup_transport_attrs(strspi_pcomp_en (starget) =0 ;spi_hold_mcs (starget) =0 ;spi_dv_pending (starget) =0 ; +spi_dv_in_progress (starget) =0 ;spi_initial_dv (starget) =0 ;mutex_init (&spi_dv_mutex (starget));@@ -907,6 +909,10 @@ spi_dv_device(struct scsi_device *sdev)if (unlikely (scsi_device_get (sdev)))return ; +if (unlikely (spi_dv_in_progress (starget))) +return ; +spi_dv_in_progress (starget) =1 ; + buffer =kzalloc (len,GFP_KERNEL );if (unlikely (!buffer))@@ -938,6 +944,7 @@ spi_dv_device(struct scsi_device *sdev) out_free:kfree (buffer); out_put: +spi_dv_in_progress (starget) =0 ;scsi_device_put (sdev); }EXPORT_SYMBOL (spi_dv_device); -To unsubscribe from this list: send the line "unsubscribe linux-scsi" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Signature · 1 line
Mark Haverkamp <[email protected]>