drivers/scsi/dpt_i2o.c: remove dead code
PATCH 1/1 drivers/scsi/dpt_i2o.c: remove dead code
The Coverity checker spotted this dead code introduced by commit a07f353701acae77e023f6270e8af353b37af7c4.
drivers/scsi/dpt_i2o.c renamed from drivers/scsi/dpt_i2o.c.old +0 -2
@@ -185,28 +185,26 @@/* search for all Adatpec I2O RAID cards */ while ((pDev =pci_get_device (PCI_DPT_VENDOR_ID ,PCI_ANY_ID , pDev))) {if (pDev->device ==PCI_DPT_DEVICE_ID || pDev->device ==PCI_DPT_RAPTOR_DEVICE_ID ){if (adpt_install_hba (sht, pDev) ){PERROR ("Could not Init an I2O RAID device\n" );PERROR ("Will not try to detect others.\n" );return hba_count-1 ; }pci_dev_get (pDev); } } -if (pDev) -pci_dev_put (pDev);/* In INIT state, Activate IOPs */ for (pHba = hba_chain; pHba; pHba = pHba->next) {// Activate does get status , init outbound, and get hrt if (adpt_i2o_activate_hba (pHba) <0 ) {adpt_i2o_delete_hba (pHba); } }/* Active IOPs in HOLD state */ rebuild_sys_tab:
Ar Llu, 2006-10-09 am 01:16 +0200, ysgrifennodd Adrian Bunk:
Quoted 4 lines
The Coverity checker spotted this dead code introduced by commit
a07f353701acae77e023f6270e8af353b37af7c4.Signed-off-by Adrian Bunk <[email protected]>
Semi-NAK
Its not dead jim, its in the wrong location
drivers/scsi/dpt_i2o.c line 192
Quoted 6 lines
drivers/scsi/dpt_i2o.c renamed from drivers/scsi/dpt_i2o.c.old +0
-0while ((pDev =pci_get_device (PCI_DPT_VENDOR_ID ,PCI_ANY_ID , pDev))) {if (pDev->device ==PCI_DPT_DEVICE_ID || pDev->device ==PCI_DPT_RAPTOR_DEVICE_ID ){if (adpt_install_hba (sht, pDev) ){PERROR ("Could not Init an I2O RAID device\n" );PERROR ("Will not try to detect others.\n" );
------------------------> pci_dev_put()
is needed there instead I think.
Been away so just catching up
Quoted 17 lines · Alan Cox
Ar Llu, 2006-10-09 am 01:16 +0200, ysgrifennodd Adrian Bunk:
Quoted 4 lines
The Coverity checker spotted this dead code introduced by commit
a07f353701acae77e023f6270e8af353b37af7c4.Signed-off-by Adrian Bunk <[email protected]>Semi-NAK
Its not dead jim, its in the wrong location
drivers/scsi/dpt_i2o.c line 192
Quoted 6 lines
drivers/scsi/dpt_i2o.c renamed from drivers/scsi/dpt_i2o.c.old +0
-0while ((pDev =pci_get_device (PCI_DPT_VENDOR_ID ,PCI_ANY_ID , pDev))) {if (pDev->device ==PCI_DPT_DEVICE_ID || pDev->device ==PCI_DPT_RAPTOR_DEVICE_ID ){if (adpt_install_hba (sht, pDev) ){PERROR ("Could not Init an I2O RAID device\n" );PERROR ("Will not try to detect others.\n" );
Quoted 4 lines
------------------------>
pci_dev_put()is needed there instead I think.
...
The current code is:
/* search for all Adatpec I2O RAID cards */
while ((pDev = pci_get_device( PCI_DPT_VENDOR_ID, PCI_ANY_ID, pDev))) {
if(pDev->device == PCI_DPT_DEVICE_ID ||
pDev->device == PCI_DPT_RAPTOR_DEVICE_ID){
if(adpt_install_hba(sht, pDev) ){
PERROR("Could not Init an I2O RAID device\n");
PERROR("Will not try to detect others.\n");
return hba_count-1;
}
pci_dev_get(pDev);
}
}
if (pDev)
pci_dev_put(pDev);I don't see the point of the suggested place for the pci_dev_put() since pci_dev_get() has never been executed in this case, or do I miss anything?
cu
Adrian
Signature · 4 lines
"Is there not promise of rain?" Ling Tan asked suddenly out
of the darkness. There had been need of rain for many days.
"Only a promise," Lao Er said.
Pearl S. Buck - Dragon SeedQuoted 3 lines
I don't see the point of the suggested place for the
pci_dev_put()sincepci_dev_get()has never been executed in this case, or do I miss anything?
Correct, thats what I get for being away and reading 4000 emails when I get back
Alan