SATA ICH5 not detected at boot, mm-kernels
Hi all; It seems that problems like this has been already reported, but not exactly the same, so maybe thsi can add some infos. Otherwise, sorry for the noise.
Starting from 2.6.19-rc1-mm1 and up to rc4-mm2, at boot the kernel is unable to detect two sata disks, connected to a ICH5 controller. Latest mm working kernel seems to be 2.6.18-mm3; 2.6.19-rc4 works just fine.
On rc-4 (vanilla) the log is this:
Nov 5 13:26:37 kefk libata version 2.00 loaded. Nov 5 13:26:37 kefk ata_piix 0000:00:1f.2: version 2.00ac6 Nov 5 13:26:37 kefk ata_piix 0000:00:1f.2: MAP [ P0 P1 IDE IDE ] Nov 5 13:26:37 kefk ACPI: PCI Interrupt 0000:00:1f.2[A] -> GSI 18 (level, low) -> IRQ 17 Nov 5 13:26:37 kefk ata: 0x170 IDE port busy Nov 5 13:26:37 kefk ata: conflict with ide1 Nov 5 13:26:37 kefk PCI: Setting latency timer of device 0000:00:1f.2 to 64 Nov 5 13:26:37 kefk ata1: SATA max UDMA/133 cmd 0x1F0 ctl 0x3F6 bmdma 0xF000 irq 14 Nov 5 13:26:37 kefk ata2: DUMMY Nov 5 13:26:37 kefk scsi1 : ata_piix Nov 5 13:26:37 kefk ata1.00: ATA-7, max UDMA/133, 488397168 sectors: LBA48 NCQ (depth 0/32) Nov 5 13:26:37 kefk ata1.00: ata1: dev 0 multi count 16 Nov 5 13:26:37 kefk ata1.01: ATA-7, max UDMA/133, 586114704 sectors: LBA48 NCQ (depth 0/32) Nov 5 13:26:37 kefk ata1.01: ata1: dev 1 multi count 16 Nov 5 13:26:37 kefk ata1.00: configured for UDMA/133 Nov 5 13:26:37 kefk ata1.01: configured for UDMA/133
With -mm kernels, I see only the third disk, but attached to a different controller (output from rc4 vanilla):
Nov 5 13:26:37 kefk ACPI: PCI Interrupt 0000:03:03.0[A] -> GSI 19 (level, low) -> IRQ 18 Nov 5 13:26:37 kefk ata3: SATA max UDMA/100 cmd 0xF8804080 ctl 0xF880408A bmdma 0xF8804000 irq 18 Nov 5 13:26:37 kefk ata4: SATA max UDMA/100 cmd 0xF88040C0 ctl 0xF88040CA bmdma 0xF8804008 irq 18 Nov 5 13:26:37 kefk scsi3 : sata_sil Nov 5 13:26:37 kefk ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310) Nov 5 13:26:37 kefk ata3.00: ATA-7, max UDMA/133, 625142448 sectors: LBA48 NCQ (depth 0/32) Nov 5 13:26:37 kefk ata3.00: ata3: dev 0 multi count 0 Nov 5 13:26:37 kefk ata3.00: configured for UDMA/100 Nov 5 13:26:37 kefk scsi4 : sata_sil Nov 5 13:26:37 kefk ata4: SATA link down (SStatus 0 SControl 310) Nov 5 13:26:37 kefk scsi 3:0:0:0: Direct-Access ATA Maxtor 6V320F0 VA11 PQ: 0 ANSI: 5 Nov 5 13:26:37 kefk SCSI device sdc: 625142448 512-byte hdwr sectors (320073 MB) Nov 5 13:26:37 kefk sdc: Write Protect is off
Signature · 4 lines
Fabio Coatti http://members.ferrara.linux.it/cova Ferrara Linux Users Group http://ferrara.linux.it GnuPG fp:9765 A5B6 6843 17BC A646 BE8C FA56 373A 5374 C703 Old SysOps never die... they simply forget their password.
Quoted 8 lines · On Sun, 5 Nov 2006 15:36:33 +0100 Fabio Coatti <[email protected]> wrote:
Hi all; It seems that problems like this has been already reported, but not exactly the same, so maybe thsi can add some infos. Otherwise, sorry for the noise.
Starting from 2.6.19-rc1-mm1 and up to rc4-mm2, at boot the kernel is unable to detect two sata disks, connected to a ICH5 controller. Latest mm working kernel seems to be 2.6.18-mm3; 2.6.19-rc4 works just fine.
Quoted 8 lines
On rc-4 (vanilla) the log is this:
Nov 5 13:26:37 kefk libata version 2.00 loaded. Nov 5 13:26:37 kefk ata_piix 0000:00:1f.2: version 2.00ac6 Nov 5 13:26:37 kefk ata_piix 0000:00:1f.2: MAP [ P0 P1 IDE IDE ] Nov 5 13:26:37 kefk ACPI: PCI Interrupt 0000:00:1f.2[A] -> GSI 18 (level, low) -> IRQ 17 Nov 5 13:26:37 kefk ata: 0x170 IDE port busy Nov 5 13:26:37 kefk ata: conflict with ide1
hm. What does that mean?
Quoted 29 lines
Nov 5 13:26:37 kefk PCI: Setting latency timer of device 0000:00:1f.2 to 64 Nov 5 13:26:37 kefk ata1: SATA max UDMA/133 cmd 0x1F0 ctl 0x3F6 bmdma 0xF000 irq 14 Nov 5 13:26:37 kefk ata2: DUMMY Nov 5 13:26:37 kefk scsi1 : ata_piix Nov 5 13:26:37 kefk ata1.00: ATA-7, max UDMA/133, 488397168 sectors: LBA48 NCQ (depth 0/32) Nov 5 13:26:37 kefk ata1.00: ata1: dev 0 multi count 16 Nov 5 13:26:37 kefk ata1.01: ATA-7, max UDMA/133, 586114704 sectors: LBA48 NCQ (depth 0/32) Nov 5 13:26:37 kefk ata1.01: ata1: dev 1 multi count 16 Nov 5 13:26:37 kefk ata1.00: configured for UDMA/133 Nov 5 13:26:37 kefk ata1.01: configured for UDMA/133With -mm kernels, I see only the third disk, but attached to a different controller (output from rc4 vanilla):
Nov 5 13:26:37 kefk ACPI: PCI Interrupt 0000:03:03.0[A] -> GSI 19 (level, low) -> IRQ 18 Nov 5 13:26:37 kefk ata3: SATA max UDMA/100 cmd 0xF8804080 ctl 0xF880408A bmdma 0xF8804000 irq 18 Nov 5 13:26:37 kefk ata4: SATA max UDMA/100 cmd 0xF88040C0 ctl 0xF88040CA bmdma 0xF8804008 irq 18 Nov 5 13:26:37 kefk scsi3 : sata_sil Nov 5 13:26:37 kefk ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310) Nov 5 13:26:37 kefk ata3.00: ATA-7, max UDMA/133, 625142448 sectors: LBA48 NCQ (depth 0/32) Nov 5 13:26:37 kefk ata3.00: ata3: dev 0 multi count 0
Quoted 9 lines
Nov 5 13:26:37 kefk ata3.00: configured for UDMA/100 Nov 5 13:26:37 kefk scsi4 : sata_sil Nov 5 13:26:37 kefk ata4: SATA link down (SStatus 0 SControl 310) Nov 5 13:26:37 kefk scsi 3:0:0:0: Direct-Access ATA Maxtor 6V320F0 VA11 PQ: 0 ANSI: 5 Nov 5 13:26:37 kefk SCSI device sdc: 625142448 512-byte hdwr sectors (320073 MB) Nov 5 13:26:37 kefk sdc: Write Protect is off
And why doesn't -mm report the same conflict? I assume the .config is the same?
Hello,
Quoted 15 lines · Andrew Morton
Quoted 11 lines · On Sun, 5 Nov 2006 15:36:33 +0100 Fabio Coatti <[email protected]> wrote:
Hi all; It seems that problems like this has been already reported, but not exactly the same, so maybe thsi can add some infos. Otherwise, sorry for the noise.
Starting from 2.6.19-rc1-mm1 and up to rc4-mm2, at boot the kernel is unable to detect two sata disks, connected to a ICH5 controller. Latest mm working kernel seems to be 2.6.18-mm3; 2.6.19-rc4 works just fine.
On rc-4 (vanilla) the log is this:
Nov 5 13:26:37 kefk libata version 2.00 loaded. Nov 5 13:26:37 kefk ata_piix 0000:00:1f.2: version 2.00ac6 Nov 5 13:26:37 kefk ata_piix 0000:00:1f.2: MAP [ P0 P1 IDE IDE ] Nov 5 13:26:37 kefk ACPI: PCI Interrupt 0000:00:1f.2[A] -> GSI 18 (level, low) -> IRQ 17 Nov 5 13:26:37 kefk ata: 0x170 IDE port busy Nov 5 13:26:37 kefk ata: conflict with ide1
Quoted 1 line
hm. What does that mean?
It means that IDE layer claimed the port. It can be overridden by combined_mode kernel parameter.
Quoted 29 lines
Quoted 14 lines
Nov 5 13:26:37 kefk PCI: Setting latency timer of device 0000:00:1f.2 to 64 Nov 5 13:26:37 kefk ata1: SATA max UDMA/133 cmd 0x1F0 ctl 0x3F6 bmdma 0xF000 irq 14 Nov 5 13:26:37 kefk ata2: DUMMY Nov 5 13:26:37 kefk scsi1 : ata_piix Nov 5 13:26:37 kefk ata1.00: ATA-7, max UDMA/133, 488397168 sectors: LBA48 NCQ (depth 0/32) Nov 5 13:26:37 kefk ata1.00: ata1: dev 0 multi count 16 Nov 5 13:26:37 kefk ata1.01: ATA-7, max UDMA/133, 586114704 sectors: LBA48 NCQ (depth 0/32) Nov 5 13:26:37 kefk ata1.01: ata1: dev 1 multi count 16 Nov 5 13:26:37 kefk ata1.00: configured for UDMA/133 Nov 5 13:26:37 kefk ata1.01: configured for UDMA/133With -mm kernels, I see only the third disk, but attached to a different controller (output from rc4 vanilla):
Quoted 14 lines
Nov 5 13:26:37 kefk ACPI: PCI Interrupt 0000:03:03.0[A] -> GSI 19 (level, low) -> IRQ 18 Nov 5 13:26:37 kefk ata3: SATA max UDMA/100 cmd 0xF8804080 ctl 0xF880408A bmdma 0xF8804000 irq 18 Nov 5 13:26:37 kefk ata4: SATA max UDMA/100 cmd 0xF88040C0 ctl 0xF88040CA bmdma 0xF8804008 irq 18 Nov 5 13:26:37 kefk scsi3 : sata_sil Nov 5 13:26:37 kefk ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310) Nov 5 13:26:37 kefk ata3.00: ATA-7, max UDMA/133, 625142448 sectors: LBA48 NCQ (depth 0/32) Nov 5 13:26:37 kefk ata3.00: ata3: dev 0 multi count 0 Nov 5 13:26:37 kefk ata3.00: configured for UDMA/100 Nov 5 13:26:37 kefk scsi4 : sata_sil Nov 5 13:26:37 kefk ata4: SATA link down (SStatus 0 SControl 310) Nov 5 13:26:37 kefk scsi 3:0:0:0: Direct-Access ATA Maxtor 6V320F0 VA11 PQ: 0 ANSI: 5 Nov 5 13:26:37 kefk SCSI device sdc: 625142448 512-byte hdwr sectors (320073 MB) Nov 5 13:26:37 kefk sdc: Write Protect is off
Quoted 2 lines
And why doesn't -mm report the same conflict? I assume the .config is the same?
Also, please post full dmesg of both kernels.
Thanks.
Signature · 1 line
tejun
Alle 13:43, lunedì 6 novembre 2006, Tejun Heo ha scritto:
Quoted 7 lines
Quoted 5 lines
Quoted 2 lines
(320073 MB)
Nov 5 13:26:37 kefk sdc: Write Protect is offAnd why doesn't -mm report the same conflict? I assume the .config is the same?
Also, please post full dmesg of both kernels.
Sure; now I'm far from the afflicted machine, but I'll post dmesg and .config for all kernels (I've to use serial console debug for the non working one:
the non working drive,unfortunately, is needed to have machine up and running :) .).
I'm pretty sure that the configs between 2.6.18-mm3 and 2.6.19-rcXmmY are the same; I've compiled newer kernel using make oldconfig based on working .config. But in the last days I've tweaked the configs trying to make it work, so I'll start a fresh build to avoid any doubt. I'll do this as soon as I'm again near the machine (I've no remote maintenance facility on this machine)
Signature · 4 lines
Fabio "Cova" Coatti http://members.ferrara.linux.it/cova Ferrara Linux Users Group http://ferrara.linux.it GnuPG fp:9765 A5B6 6843 17BC A646 BE8C FA56 373A 5374 C703 Old SysOps never die... they simply forget their password.
It seems that my message hasn't yet shown up on lkml, so I suppose to have some mail problem :(
To see if this helps, I've removed attachments, replacing it with urls.
Alle 13:43, lunedì 6 novembre 2006, Tejun Heo ha scritto:
Quoted 14 lines
Hello,
Quoted 11 lines · Andrew Morton
On Sun, 5 Nov 2006 15:36:33 +0100
Quoted 8 lines · Fabio Coatti
Hi all; It seems that problems like this has been already reported, but not exactly the same, so maybe thsi can add some infos. Otherwise, sorry for the noise.
Starting from 2.6.19-rc1-mm1 and up to rc4-mm2, at boot the kernel is unable to detect two sata disks, connected to a ICH5 controller. Latest mm working kernel seems to be 2.6.18-mm3; 2.6.19-rc4 works just fine.
I've collected more data; Here you can find .config for all three cases:
2.6.18-mm3 (working) http://members.ferrara.linux.it/cova/config-2.6.18-mm3
2.6.19-rc5 (working) http://members.ferrara.linux.it/cova/config-2.6.19-rc5
2.6.19-rc5-mm1 (not working)
http://members.ferrara.linux.it/cova/config-2.6.19-rc5-mm1
and dmesg for 2.6.18-mm3 and 2.6.19-rc5. I've seen that I've saved the dmesg with nvidia driver inserted; I can't, right now, recreate the files without nvidia driver loaded, but as the issue happens before the driver is loaded maybe the information can be useful anyway. I'll made a non tainted dmesg as soon as possible, if needed.
http://members.ferrara.linux.it/cova/dmesg-2.6.18-mm3
http://members.ferrara.linux.it/cova/dmesg-2.6.19-rc5
I'm trying to get the dmesg for 2.6.19-rc-mm1 (the non-working one), but I've to find a serial cable :)
Anyway, I've seen this message on dmesg, that seems interesting (copied by hand, please forgive any mistake):
PCI: Unable to reserve I/O region #1:8@1f0 for device 0000:00:1f.2ata_piix: probe of 0000:00:1f.2 failed with error -16
Of course, lspci for that device gives:
00:1f.2 IDE interface: Intel Corporation 82801EB (ICH5) SATA Controller (rev
02) (prog-if 8a [Master SecP PriP])
Subsystem: ABIT Computer Corp. Unknown device 1014
Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 17 I/O ports at <unassigned>
I/O ports at <unassigned>
I/O ports at <unassigned>
I/O ports at <unassigned>
I/O ports at f000 [size=16]
HTH
Signature · 4 lines
Fabio Coatti http://members.ferrara.linux.it/cova Ferrara Linux Users Group http://ferrara.linux.it GnuPG fp:9765 A5B6 6843 17BC A646 BE8C FA56 373A 5374 C703 Old SysOps never die... they simply forget their password.
Alle 14:18, lunedì 6 novembre 2006, Fabio Coatti ha scritto:
Quoted 8 lines
Alle 13:43, lunedì 6 novembre 2006, Tejun Heo ha scritto:
Quoted 7 lines
Quoted 5 lines
Quoted 2 lines
(320073 MB)
Nov 5 13:26:37 kefk sdc: Write Protect is offAnd why doesn't -mm report the same conflict? I assume the .config is the same?
Also, please post full dmesg of both kernels.
I've finally saved the dmesg from 2.6.19-rc5-mm1, the one that hangs at boot, not detecting two sata disks:
BIOS data check successful
Linux version 2.6.19-rc5-mm1 (root@kefk) (gcc version 4.1.1 (Gentoo 4.1.1-r1)) #2 SMP PREEMPT Sun Nov 12 20:17:00 CET 2006
BIOS-provided physical RAM map:
sanitize start
sanitize endcopy_e820_map() start: 0000000000000000 size: 000000000009f800 end:000000000009f800 type: 1copy_e820_map() type is E820_RAMcopy_e820_map() start: 000000000009f800 size: 0000000000000800 end:00000000000a0000 type: 2copy_e820_map() start: 00000000000f0000 size: 0000000000010000 end:
0000000000100000 type: 2copy_e820_map() start: 0000000000100000 size: 000000003fef0000 end:000000003fff0000 type: 1copy_e820_map() type is E820_RAMcopy_e820_map() start: 000000003fff0000 size: 0000000000003000 end:000000003fff3000 type: 4copy_e820_map() start: 000000003fff3000 size: 000000000000d000 end:
0000000040000000 type: 3copy_e820_map() start: 00000000fec00000 size: 0000000001400000 end:
0000000100000000 type: 2
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003fff0000 (usable)
BIOS-e820: 000000003fff0000 - 000000003fff3000 (ACPI NVS)
BIOS-e820: 000000003fff3000 - 0000000040000000 (ACPI data)
BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
127MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000f5cd0
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 229376
HighMem 229376 -> 262128
early_node_map[1] active PFN ranges
0: 0 -> 262128
DMI 2.2 present.
ACPI: PM-Timer IO Port: 0x408
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:2 APIC version 20
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1 15:2 APIC version 20
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 50000000 (gap: 40000000:bec00000) Detected 2806.502 MHz processor.
Built 1 zonelists. Total pages: 260081
Kernel command line: BOOT_IMAGE=2.6.19-rc5-mm1s ro root=821 console=ttyS0,38400
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0
Clock event device pit configured with caps set: 07
PID hash table entries: 4096 (order: 12, 16384 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1034388k/1048512k available (2712k kernel code, 13556k reserved, 1300k data, 212k init, 131008k highmem)
virtual kernel memory layout:
fixmap : 0xfff9d000 - 0xfffff000 ( 392 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
.init : 0xc04f1000 - 0xc0526000 ( 212 kB)
.data : 0xc03a63ef - 0xc04eb634 (1300 kB)
.text : 0xc0100000 - 0xc03a63ef (2712 kB)Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 5615.03 BogoMIPS (lpj=2807516)
Security Framework v1.0.0 initialized
Mount-cache hash table entries: 512
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU0: Thermal monitoring enabled
Checking 'hlt' instruction... OK.
Freeing SMP alternatives: 11k freed
ACPI: Core revision 20060707
CPU0: Intel(R) Pentium(R) 4 CPU 2.80GHz stepping 09
Booting processor 1/1 eip 2000
Initializing CPU#1
Calibrating delay using timer specific routine.. 5611.95 BogoMIPS (lpj=2805977)
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel P4/Xeon Extended MCE MSRs (12) available
CPU1: Thermal monitoring enabled
CPU1: Intel(R) Pentium(R) 4 CPU 2.80GHz stepping 09
Total of 2 processors activated (11226.98 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
Clock event device pit new caps set: 01
Clock event device lapic configured with caps set: 06
checking TSC synchronization across 2 CPUs: passed.
Clock event device pit new caps set: 01
Clock event device lapic configured with caps set: 06
Brought up 2 CPUs
migration_cost=88
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfbb20, last bus=3
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI quirk: region 0400-047f claimed by ICH4 ACPI/GPIO/TCO
PCI quirk: region 0480-04bf claimed by ICH4 GPIO
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Link [LNKA] (IRQs *3 4 5 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 *5 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 *5 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 7 9 10 *11 12 14 15)
ACPI: Power Resource [PFAN] (off)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 14 devices
Generic PHY: Registered new driver
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
pnp: 00:0b: ioport range 0x400-0x4bf could not be reserved
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: f8000000-f9ffffff
PREFETCH window: f0000000-f7ffffff
PCI: Bridge: 0000:00:03.0
IO window: a000-afff
MEM window: fc000000-fc0fffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1e.0
IO window: 8000-9fff
MEM window: fa000000-fbffffff
PREFETCH window: 50000000-500fffff
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes) TCP established hash table entries: 131072 (order: 8, 1572864 bytes) TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
Machine check exception polling timer started.
KEVENT subsystem has been successfully registered.
KEVENT: Added callbacks for type 2.
KEVENT: Added callbacks for type 3.
Kevent poll()/select() subsystem has been initialized.
KEVENT: Added callbacks for type 0.
highmem bounce pool size: 64 pages
JFS: nTxBlock = 8082, nTxLock = 64661
SGI XFS with ACLs, no debug enabled
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ACPI: Transitioning device [FAN] to D3
ACPI: Transitioning device [FAN] to D3
ACPI: Fan [FAN] (off)
ACPI: Invalid passive threshold
ACPI: Thermal Zone [THRM] (55 C)
[drm] Initialized drm 1.1.0 20060810
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
LXT970: Registered new driver
LXT971: Registered new driver
netconsole: not configured, aborting
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ide0: I/O resource 0x1F0-0x1F7 not free.
ide0: ports already in use, skipping probe
hdc: TEAC DV-W58G, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
ACPI: PCI Interrupt 0000:03:06.0[A] -> GSI 22 (level, low) -> IRQ 16 ahc_pci:3:6:0: Host Adapter Bios disabled. Using default SCSI device parameters
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0
<Adaptec 2902/04/10/15/20C/30C SCSI adapter>
aic7850: Single Channel A, SCSI Id=7, 3/253 SCBsscsi 0:0:2:0: Scanner Nikon COOLSCANIII 1.31 PQ: 0 ANSI: 2
target0:0:2: Beginning Domain Validation
target0:0:2: Ending Domain Validation
scsi 0:0:3:0: CD-ROM PLEXTOR CD-ROM PX-40TS 1.01 PQ: 0 ANSI: 2
target0:0:3: Beginning Domain Validation
target0:0:3: FAST-10 SCSI 10.0 MB/s ST (100 ns, offset 15) target0:0:3: Domain Validation skipping write tests
target0:0:3: Ending Domain Validation
sr0: scsi-1 drive
Uniform CD-ROM driver Revision: 3.20
scsi 0:0:2:0: Attached scsi generic sg0 type 6
sr 0:0:3:0: Attached scsi generic sg1 type 5ata_piix 0000:00:1f.2: MAP [ P0 P1 IDE IDE ]
ACPI: PCI Interrupt 0000:00:1f.2[A] -> GSI 18 (level, low) -> IRQ 17
PCI: Unable to reserve I/O region #1:8@1f0 for device 0000:00:1f.2ata_piix: probe of 0000:00:1f.2 failed with error -16
ACPI: PCI Interrupt 0000:03:03.0[A] -> GSI 19 (level, low) -> IRQ 18
ata1: SATA max UDMA/100 cmd 0xF8804080 ctl 0xF880408A bmdma 0xF8804000 irq 18
ata2: SATA max UDMA/100 cmd 0xF88040C0 ctl 0xF88040CA bmdma 0xF8804008 irq 18 scsi1 : sata_sil
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: ATA-7, max UDMA/133, 625142448 sectors: LBA48 NCQ (depth 0/32) ata1.00: ata1: dev 0 multi count 0
ata1.00: configured for UDMA/100
scsi2 : sata_sil
ata2: SATA link down (SStatus 0 SControl 310)
scsi 1:0:0:0: Direct-Access ATA Maxtor 6V320F0 VA11 PQ: 0 ANSI: 5
SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
sda: Write Protect is off
SCSI device sda: drive cache: write back
SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
sda: Write Protect is off
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda3 sda4 < sda5 >
sd 1:0:0:0: Attached scsi disk sda
sd 1:0:0:0: Attached scsi generic sg2 type 0
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
EDAC MC: Ver: 2.0.1 Nov 10 2006
EDAC i82875p: i82875p init one
EDAC MC0: Giving out device to i82875p_edac i82875p: DEV 0000:00:00.0
input: AT Translated Set 2 keyboard as /class/input/input0
TCP bic registered
TCP westwood registered
TCP htcp registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Starting balanced_irq
Using IPI Shortcut modedrivers/rtc/hctosys.c: unable to open rtc device (rtc0)
Time: tsc clocksource has been installed.
logips2pp: Detected unknown logitech mouse model 127
input: ImExPS/2 Logitech Explorer Mouse as /class/input/input1
VFS: Cannot open root device "821" or unknown-block(8,33)
Please append a correct "root=" boot option
Kernel panic - not syncing: VFS: Unable to mount root fs on
unknown-block(8,33)
Signature · 4 lines
Fabio Coatti http://members.ferrara.linux.it/cova Ferrara Linux Users Group http://ferrara.linux.it GnuPG fp:9765 A5B6 6843 17BC A646 BE8C FA56 373A 5374 C703 Old SysOps never die... they simply forget their password.
Quoted 5 lines · On Mon, 13 Nov 2006 10:17:38 +0100 Fabio Coatti <[email protected]> wrote:
Alle 14:18,
luned__6 novembre 2006, Fabio Coatti ha scritto:Quoted 4 lines
Alle 13:43,
luned__6 novembre 2006, Tejun Heo ha scritto:Quoted 3 lines
Quoted 3 lines
Quoted 2 lines
(320073 MB)
Nov 5 13:26:37 kefk sdc: Write Protect is off
Quoted 7 lines
Quoted 4 lines
Quoted 4 lines
Quoted 2 lines
And why doesn't -mm report the same conflict? I assume the .config is the same?
Also, please post full dmesg of both kernels.
I've finally saved the dmesg from 2.6.19-rc5-mm1, the one that hangs at boot, not detecting two sata disks:
Thanks.
Quoted 8 lines · Tejun
Quoted 4 lines
Quoted 2 lines
Nov 5 13:26:37 kefk ata: 0x170 IDE port busy Nov 5 13:26:37 kefk ata: conflict with ide1hm. What does that mean?
It means that IDE layer claimed the port. It can be overridden by
combined_modekernel parameter.
Did you try that?
Alle 22:29, lunedì 13 novembre 2006, Andrew Morton ha scritto:
Quoted 11 lines
Quoted 7 lines · Tejun
Quoted 4 lines
Quoted 2 lines
Nov 5 13:26:37 kefk ata: 0x170 IDE port busy Nov 5 13:26:37 kefk ata: conflict with ide1hm. What does that mean?
It means that IDE layer claimed the port. It can be overridden by
combined_modekernel parameter.Did you try that?
Uh, well, to be honest, no..or better: not yet :)
anyway, applying this patch: http://lkml.org/lkml/2006/11/13/150
tghe problem disappeared and 2.6.19-rc5-mm1 booted just fine, seeing all ata_piix devices.
Quoted 12 lines · On Tue, 14 Nov 2006 22:52:42 +0100 Fabio Coatti <[email protected]> wrote:
Alle 22:29,
luned__13 novembre 2006, Andrew Morton ha scritto:Quoted 10 lines
Quoted 7 lines · Tejun
Quoted 4 lines
Quoted 2 lines
Nov 5 13:26:37 kefk ata: 0x170 IDE port busy Nov 5 13:26:37 kefk ata: conflict with ide1hm. What does that mean?
It means that IDE layer claimed the port. It can be overridden by
combined_modekernel parameter.
Quoted 7 lines
Quoted 1 line
Did you try that?
Uh, well, to be honest, no..or better: not yet :)
anyway, applying this patch: http://lkml.org/lkml/2006/11/13/150
tghe problem disappeared and 2.6.19-rc5-mm1 booted just fine, seeing allata_piixdevices.
Great, thanks.
I have that fix in rc5-mm2, as pci-quirks-fix-the-festering-mess-that-claims-to-handle-ide-quirks-ide-fix.patch
- a fix against Greg's gregkh-pci-pci-quirks-fix-the-festering-mess-that-claims-to-handle-ide-quirks.patch
There is no problem which cannot be solved with a sufficiently long filename.