Skip to contentSkip to conversation

CD oddities with VIA PATA

DISCUSSION Ken Moffat 2 participants 4 messages Dec 1, 2006 – Dec 4, 2006

lore
Share & tools
lore

Ken Moffat

author
#0 lore raw

I'm testing 2.6.19 on this box, and I thought I might as well try
out the Parallel ATA driver for the CD/DVD writer (VIA) since the disk is already handled by libata.

So far, I've found two oddities -

(i.) cdparanoia (9.8) works for root, but for a user it complains that the ioctl isn't cooked and refuses to run. For test purposes, it runs ok for a user as suid root, but I imagine that increases the likelihood of unspeakable things happening. (Fortunately, I don't have a dachshund)

(ii.) As a user, I burned a small (28MB) CD using dvdrecord from dvdrtools-0.3.1, and on a different box I can mount it (using ide-cd) and it seems fine. On this box I can't mount it -

ken@ac30 ~ $mount /media/cdrom/
mount: wrong fs type, bad option, bad superblock on /dev/cdrom,
missing codepage or other error
In some cases useful info is found in syslog - try dmesg | tail or so

The syslog shows

Dec  1 21:17:41 ac30 kernel: attempt to access beyond end of device
Dec  1 21:17:41 ac30 kernel: sr0: rw=0, want=68, limit=4
Dec  1 21:17:41 ac30 kernel: isofs_fill_super: bread failed, dev=sr0, iso_blknum=16, block=16

The iso is the gparted-livecd-0.3.1-1.iso.

The problem might be specific to small CDs, I can mount others (41M
of data and more) without difficulty and all of the likely NLS options are selected as =y in my config.

Ken

Signature · 1 line
das eine Mal als Tragödie, das andere Mal als Farce
author
#1 lore raw
Quoted 7 lines · Ken Moffat

(i.) cdparanoia (9.8) works for root, but for a user it complains that the ioctl isn't cooked and refuses to run. For test purposes, it runs ok for a user as suid root, but I imagine that increases the likelihood of unspeakable things happening. (Fortunately, I don't have a dachshund)

Forgot to mention the lines in the log from cdparanoia, but I think
these frequent messages are expected:

Dec  1 20:35:53 ac30 kernel: sg_write: data in/out 30576/30576 bytes for SCSI command 0xbe--guessing data in;
Dec  1 20:35:53 ac30 kernel:    program cdparanoia not setting count and/or reply_len properly

Also forgot the details of the drive, just in case

Dec  1 19:17:14 ac30 kernel: scsi3 : pata_via
Dec  1 19:17:14 ac30 kernel: ata4.00: ATAPI, max UDMA/66
Dec  1 19:17:14 ac30 kernel: Losing some ticks... checking if CPU frequency changed.
Dec  1 19:17:14 ac30 kernel: ata4.00: configured for UDMA/66
Dec  1 19:17:14 ac30 kernel: scsi 3:0:0:0: CD-ROM            LITE-ON DVDRW SHW-1635S  YS0G PQ: 0 ANSI: 5
Dec  1 19:17:14 ac30 kernel: sr0: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray
Dec  1 19:17:14 ac30 kernel: Uniform CD-ROM driver Revision: 3.20
Dec  1 19:17:14 ac30 kernel: sr 3:0:0:0: Attached scsi CD-ROM sr0
Dec  1 19:17:14 ac30 kernel: sr 3:0:0:0: Attached scsi generic sg1 type 5

Ken

Signature · 1 line
das eine Mal als Tragödie, das andere Mal als Farce
#2 lore raw
Quoted 6 lines · Ken Moffat
Quoted 5 lines · Ken Moffat

(i.) cdparanoia (9.8) works for root, but for a user it complains that the ioctl isn't cooked and refuses to run. For test purposes, it runs ok for a user as suid root, but I imagine that increases the likelihood of unspeakable things happening. (Fortunately, I don't have a dachshund)

For the record,
cdparanoia III release 10pre0 (August 29, 2006)

works for me. My particular IDE adapter is:

00:0f.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])

I have not tried older versions (yet). Could you try this and see if things are still broken?

Signature · 1 line
Joshua Kwan
author
#3 lore raw
Quoted 11 lines · Joshua Kwan
Quoted 6 lines · Ken Moffat
Quoted 5 lines · Ken Moffat

(i.) cdparanoia (9.8) works for root, but for a user it complains that the ioctl isn't cooked and refuses to run. For test purposes, it runs ok for a user as suid root, but I imagine that increases the likelihood of unspeakable things happening. (Fortunately, I don't have a dachshund)

For the record,
cdparanoia III release 10pre0 (August 29, 2006)

Quoted 12 lines

works for me. My particular IDE adapter is:

00:0f.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])

I have not tried older versions (yet). Could you try this and see if things are still broken?

Signature · 1 line
Joshua Kwan

I had tried it, but it turns out my trial used the old installed
libcdda_* libraries. Now that I've got it using the new versions of these, it looks as if 10pre0, with the debian patches, works ok for a normal user (on x86_64 it needs the patch to be able to configure).

Thanks for the pointer. FWIW I can no longer replicate the failure
to mount a CD it had burned, will be doing more tests later.

Ken

Signature · 1 line
das eine Mal als Tragödie, das andere Mal als Farce