2.6.20-rc4: null pointer deref in khubd
Hi!
I have half broken usb device here, very useful at breaking linux usb stack:
(Is it softlockup watchdog triggering in the middle of oops? Do we
take too long to oops or what?)
Pavel
...
PM: Adding info for usb:2-1:1.0
usb0: register 'cdc_ether' at usb-0000:00:1d.0-1, CDC Ethernet Device, c2:3a:65:0e:e0:f7
PM: Adding info for No Bus:usbdev2.60_ep83
PM: Adding info for usb:2-1:1.1
PM: Adding info for No Bus:usbdev2.60_ep81
PM: Adding info for No Bus:usbdev2.60_ep02
PM: Adding info for mmc:mmc0:0001
mmcblk0: mmc0:0001 IFX128 125440KiB
mmcblk0: p1 p2 p3
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
usb 2-1: USB disconnect, address 60
PM: Removing info for No Bus:usbdev2.60_ep83
usb0: unregister 'cdc_ether' usb-0000:00:1d.0-1, CDC Ethernet Device
PM: Removing info for usb:2-1:1.0
PM: Removing info for No Bus:usbdev2.60_ep81
PM: Removing info for No Bus:usbdev2.60_ep02
PM: Removing info for usb:2-1:1.1
PM: Removing info for No Bus:usbdev2.60_ep00
PM: Removing info for usb:2-1
usb 2-1: new full speed USB device using uhci_hcd and address 61
usb 2-1: device descriptor read/64, error -71
PM: Removing info for mmc:mmc0:0001
usb 2-1: new full speed USB device using uhci_hcd and address 62
usb 2-1: device descriptor read/64, error -71
usb 2-1: new full speed USB device using uhci_hcd and address 63
usb 2-1: new full speed USB device using uhci_hcd and address 64
usb 2-1: new full speed USB device using uhci_hcd and address 65
usb 2-1: new full speed USB device using uhci_hcd and address 66
usb 2-1: device descriptor read/all, error -71
usb 2-1: new full speed USB device using uhci_hcd and address 68
usb 2-1: USB disconnect, address 68
usb 2-1: unable to read config index 0 descriptor/start
usb 2-1: chopping to 0 config(s)
usb 2-1: string descriptor 0 read error: -19
usb 2-1: string descriptor 0 read error: -19
PM: Adding info for usb:2-1
BUG: unable to handle kernel NULL pointer dereference at virtual address 00000010 printing eip:
c0610784
*pde = 00000000
PM: Adding info for No Bus:usbdev2.68_ep00
usb 2-1: no configuration chosen from 0 choices
BUG: soft lockup detected on CPU#1! [<c014d4c9>] softlockup_tick+0xa9/0xd0 [<c0131393>] update_process_times+0x33/0x80 [<c011ab7b>] smp_apic_timer_interrupt+0x6b/0x80 [<c0103aa4>] apic_timer_interrupt+0x28/0x30 [<c02558b4>] delay_tsc+0x14/0x20 [<c02558f6>] __delay+0x6/0x10 [<c011fbbb>] do_page_fault+0x35b/0x600 [<c011f860>] do_page_fault+0x0/0x600 [<c061352c>] error_code+0x7c/0x84 [<c0610784>] klist_del+0x14/0x50 [<c0328edb>] device_del+0x1b/0x1c0 [<c044c2a1>] usb_disconnect+0xb1/0x120 [<c044ec4a>] hub_thread+0x3ca/0xe00 [<c0120ab1>] __activate_task+0x21/0x40 [<c01238af>] try_to_wake_up+0x3f/0x420 [<c013c6c0>] autoremove_wake_function+0x0/0x50 [<c044e880>] hub_thread+0x0/0xe00 [<c013c60c>] kthread+0xec/0xf0 [<c013c520>] kthread+0x0/0xf0 [<c0103be7>] kernel_thread_helper+0x7/0x10 ======================= Oops: 0000 [#1] SMP Modules linked in: usbserial CPU: 1 EIP: 0060:[<c0610784>] Not tainted VLI EFLAGS: 00010292 (2.6.20-rc4 #387)
EIP is at klist_del+0x14/0x50
eax: 00000000 ebx: 00000000 ecx: 0000000f edx: 00000000
esi: 0000007c edi: df17c4f4 ebp: df17c5c8 esp: c21b3ea4
ds: 007b es: 007b ss: 0068
Process khubd (pid: 304, ti=c21b2000 task=c2264030 task.ti=c21b2000)
Stack: df17c504 0000007c df17c4e0 c0328edb f79f76d0 df17c504 0000007c df17c488
df17c5c8 c044c2a1 c0735194 c0704518 df17c598 00000044 f79f78f8 df17c4e0
c21ffd1c c2251b50 f79f7678 c21ffd04 c044ec4a c21b3fb0 0000000a c21b3f10
Call Trace:
[<c0328edb>] device_del+0x1b/0x1c0
[<c044c2a1>] usb_disconnect+0xb1/0x120
[<c044ec4a>] hub_thread+0x3ca/0xe00
[<c0120ab1>] __activate_task+0x21/0x40
[<c01238af>] try_to_wake_up+0x3f/0x420
[<c013c6c0>] autoremove_wake_function+0x0/0x50
[<c044e880>] hub_thread+0x0/0xe00
[<c013c60c>] kthread+0xec/0xf0
[<c013c520>] kthread+0x0/0xf0
[<c0103be7>] kernel_thread_helper+0x7/0x10
=======================
Code: 04 89 46 04 89 4a 04 89 11 c6 03 01 8b 1c 24 8b 74 24 04 83 c4 08 c3 83 ec 0c 89 7c 24 08 89 c7 89 1c 24 89 74 24 04 8b 18 89 d8 <8b> 73 10 e8 f4 29 00 00 89 f8 e8 ad fe ff ff 85 c0 b8 00 00 00
EIP: [<c0610784>] klist_del+0x14/0x50 SS:ESP 0068:c21b3ea4Signature · 2 lines
(english) http://www.livejournal.com/~pavelmachek (cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html
Am Mittwoch, 10. Januar 2007 11:49 schrieb Pavel Machek:
Quoted 4 lines
usb 2-1: new full speed USB device using
uhci_hcdand address 68 usb 2-1: USB disconnect, address 68
usb 2-1: unable to read config index 0 descriptor/start usb 2-1: chopping to 0 config(s)
Does anybody know a legitimate reasons a device should have
0 configurations? Independent of the reason of this bug, should we disallow such devices and error out?
Regards
Oliver
Quoted 9 lines · Oliver Neukum
Am Mittwoch, 10. Januar 2007 11:49 schrieb Pavel Machek:
Quoted 4 lines
usb 2-1: new full speed USB device using
uhci_hcdand address 68 usb 2-1: USB disconnect, address 68
usb 2-1: unable to read config index 0 descriptor/start usb 2-1: chopping to 0 config(s)Does anybody know a legitimate reasons a device should have
0 configurations? Independent of the reason of this bug, should we disallow such devices and error out?
About the only reason to allow such devices is so that the user can run lsusb to try and get more information about the problem. With no configurations, the device won't be useful for anything.
Alan Stern
Am Mittwoch, 10. Januar 2007 17:14 schrieb Alan Stern:
Quoted 8 lines · Oliver Neukum
Quoted 7 lines
Am Mittwoch, 10. Januar 2007 11:49 schrieb Pavel Machek:
Quoted 4 lines
usb 2-1: new full speed USB device using
uhci_hcdand address 68 usb 2-1: USB disconnect, address 68
usb 2-1: unable to read config index 0 descriptor/start usb 2-1: chopping to 0 config(s)
Quoted 7 lines
Quoted 3 lines
Does anybody know a legitimate reasons a device should have
0 configurations? Independent of the reason of this bug, should we disallow such devices and error out?About the only reason to allow such devices is so that the user can run lsusb to try and get more information about the problem. With no configurations, the device won't be useful for anything.
Regarding the bug this device uncovers, it seems to me that this in drivers/base/core.c
if (parent) klist_add_tail(&dev->knode_parent, &parent->klist_children);
should make knode_parent a valid node under all circumstances. Hm.
Regards
Oliver
Quoted 17 lines · Oliver Neukum
Am Mittwoch, 10. Januar 2007 17:14 schrieb Alan Stern:
Quoted 8 lines · Oliver Neukum
Quoted 7 lines
Am Mittwoch, 10. Januar 2007 11:49 schrieb Pavel Machek:
Quoted 4 lines
usb 2-1: new full speed USB device using
uhci_hcdand address 68 usb 2-1: USB disconnect, address 68
usb 2-1: unable to read config index 0 descriptor/start usb 2-1: chopping to 0 config(s)Quoted 7 lines
Quoted 3 lines
Does anybody know a legitimate reasons a device should have
0 configurations? Independent of the reason of this bug, should we disallow such devices and error out?About the only reason to allow such devices is so that the user can run lsusb to try and get more information about the problem. With no configurations, the device won't be useful for anything.
Quoted 5 lines
Regarding the bug this device uncovers, it seems to me that this in
drivers/base/core.cif (parent) klist_add_tail(&dev->knode_parent, &parent->klist_children);should make
knode_parenta valid node under all circumstances. Hm.
I haven't seen the original bug report. Where does the NULL pointer deref occur?
Alan Stern
Am Mittwoch, 10. Januar 2007 18:31 schrieb Alan Stern:
Quoted 8 lines
Quoted 5 lines
Regarding the bug this device uncovers, it seems to me that this in
drivers/base/core.cif (parent)
klist_add_tail(&dev->knode_parent,&parent->klist_children); should makeknode_parenta valid node under all circumstances.
Hm.I haven't seen the original bug report. Where does the NULL pointer deref occur?
Apparently here: drivers/base/core.c:
void device_del(struct device * dev)
{
struct device * parent = dev->parent;
struct class_interface *class_intf;
if (parent)
klist_del(&dev->knode_parent);The obvious change with this device is that usb_set_configuration() is never called, but that should not matter.
Regards
Oliver
Quoted 20 lines · Oliver Neukum
Am Mittwoch, 10. Januar 2007 18:31 schrieb Alan Stern:
Quoted 8 lines
Quoted 5 lines
Regarding the bug this device uncovers, it seems to me that this in
drivers/base/core.cif (parent)
klist_add_tail(&dev->knode_parent,&parent->klist_children); should makeknode_parenta valid node under all circumstances.
Hm.I haven't seen the original bug report. Where does the NULL pointer deref occur?
Apparently here:
drivers/base/core.c:void
device_del(struct device * dev){ struct device * parent = dev->parent; struct class_interface *class_intf; if (parent) klist_del(&dev->knode_parent);
Quoted 2 lines
The obvious change with this device is that
usb_set_configuration()is never called, but that should not matter.
No, I think you're barking up the wrong tree.
Pavel, did you have CONFIG_USB_MULTITHREAD_PROBE turned on? I bet you did -- there's no other way to generate the messages in your syslog.
Don't use that kconfig option. It's broken (as you saw) and needs to be either removed or replaced.
Alan Stern
Hi!
Quoted 7 lines
Quoted 2 lines
The obvious change with this device is that
usb_set_configuration()is never called, but that should not matter.No, I think you're barking up the wrong tree.
Pavel, did you have
CONFIG_USB_MULTITHREAD_PROBEturned on? I bet you did -- there's no other way to generate the messages in your syslog.
Yep, you are right.
Quoted 2 lines
Don't use that kconfig option. It's broken (as you saw) and needs to be either removed or replaced.
Perhaps it should be disabled before 2.6.20? This is actually regression...
Pavel
Signature · 2 lines
(english) http://www.livejournal.com/~pavelmachek (cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html
Am Mittwoch, 10. Januar 2007 23:35 schrieb Alan Stern:
Quoted 7 lines
Quoted 7 lines
Apparently here:
drivers/base/core.c:void
device_del(struct device * dev)
{
struct device * parent =dev->parent;
structclass_interface*class_intf;
Quoted 7 lines
Quoted 5 lines
if (parent)
klist_del(&dev->knode_parent);The obvious change with this device is that
usb_set_configuration()is never called, but that should not matter.No, I think you're barking up the wrong tree.
OK. Next time I'll ask about config options before going through working code looking for a bug.
Regards
Oliver
Quoted 11 lines · Oliver Neukum
Am Mittwoch, 10. Januar 2007 23:35 schrieb Alan Stern:
Quoted 10 lines
Quoted 10 lines
Apparently here:
drivers/base/core.c:void
device_del(struct device * dev)
{
struct device * parent =dev->parent;
structclass_interface*class_intf;if (parent)
klist_del(&dev->knode_parent);
Quoted 7 lines
Quoted 4 lines
Quoted 2 lines
The obvious change with this device is that
usb_set_configuration()is never called, but that should not matter.No, I think you're barking up the wrong tree.
OK. Next time I'll ask about config options before going through working code looking for a bug.
Can we delete that config option for 2.6.20? (And sorry for a crappy report).
Signature · 2 lines
(english) http://www.livejournal.com/~pavelmachek (cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html
Am Donnerstag, 11. Januar 2007 11:34 schrieb Pavel Machek:
[on USB_MULTITHREAD_PROBE]
Quoted 1 line
Can we delete that config option for 2.6.20? (And sorry for a crappy report).
Somebody already has done so, however he left the module parameter. I'll remove that, too.
Regards
Oliver
Hi!
Quoted 8 lines
Quoted 4 lines
usb 2-1: new full speed USB device using
uhci_hcdand address 68 usb 2-1: USB disconnect, address 68
usb 2-1: unable to read config index 0 descriptor/start usb 2-1: chopping to 0 config(s)Does anybody know a legitimate reasons a device should have
0 configurations? Independent of the reason of this bug, should we disallow such devices and error out?
It is not bad device, btw, but extremely flakey connector. Bug is random :-(, and machine is smp, so it might even be a race.
Pavel
Signature · 1 line
Thanks for all the (sleeping) penguins.
Am Mittwoch, 10. Januar 2007 21:38 schrieb Pavel Machek:
Quoted 7 lines
Hi!
Quoted 5 lines
Quoted 4 lines
usb 2-1: new full speed USB device using
uhci_hcdand address 68 usb 2-1: USB disconnect, address 68
usb 2-1: unable to read config index 0 descriptor/start usb 2-1: chopping to 0 config(s)
Quoted 6 lines
Quoted 3 lines
Does anybody know a legitimate reasons a device should have
0 configurations? Independent of the reason of this bug, should we disallow such devices and error out?It is not bad device, btw, but extremely flakey connector. Bug is random :-(, and machine is smp, so it might even be a race.
With that config option, there's a race even on UP. probe() can sleep.
Regards
Oliver