Skip to contentSkip to conversation

SATA exceptions triggered by XFS (since 2.6.18)

DISCUSSION Paolo Ornati 5 participants 12 messages Jan 21, 2007 – Jan 22, 2007

lore
Share & tools
lore
#0 lore raw

Sorry for starting a new thread, but I've deleted the messages from my mail-box, and I'm sot sure it's the same problem as here:

	http://lkml.org/lkml/2007/1/14/108

Today I've decided to try XFS... and just doing anything on it (extracting a tarball, for example) make my SATA HD go crazy ;)

I don't remember to have seen this using Ext3.

[  877.839920] ata1.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x2 frozen
[  877.839929] ata1.00: cmd 61/02:00:64:98:98/00:00:00:00:00/40 tag 0 cdb 0x0 data 1024 out
[  877.839931]          res 40/00:00:00:4f:c2/00:00:00:4f:c2/00 Emask 0x4 (timeout)
[  878.142367] ata1: soft resetting port
[  878.351791] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[  878.354384] ata1.00: configured for UDMA/133
[  878.354392] ata1: EH complete
[  878.355696] SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
[  878.355716] sda: Write Protect is off
[  878.355718] sda: Mode Sense: 00 3a 00 00
[  878.355745] SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA

It takes nothing to reproduce it.

My hardware is:

00:00.0 Host bridge: Intel Corporation 82P965/G965 Memory Controller Hub (rev 02) 00:02.0 VGA compatible controller: Intel Corporation 82G965 Integrated Graphics Controller (rev 02) 00:03.0 Communication controller: Intel Corporation 82P965/G965 HECI Controller (rev 02) 00:19.0 Ethernet controller: Intel Corporation 82566DC Gigabit Network Connection (rev 02) 00:1a.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI #4 (rev 02) 00:1a.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI #5 (rev 02) 00:1a.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI #2 (rev 02) 00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio Controller (rev 02) 00:1c.0 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 (rev 02) 00:1c.1 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 2 (rev 02) 00:1c.2 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 3 (rev 02) 00:1c.3 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 4 (rev 02) 00:1c.4 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 5 (rev 02) 00:1d.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI #1 (rev 02) 00:1d.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI #2 (rev 02) 00:1d.2 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI #3 (rev 02) 00:1d.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI #1 (rev 02) 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev f2)
00:1f.0 ISA bridge: Intel Corporation 82801HB/HR (ICH8/R) LPC Interface Controller (rev 02) 00:1f.2 SATA controller: Intel Corporation 82801HB (ICH8) 4 port SATA AHCI Controller (rev 02) 00:1f.3 SMBus: Intel Corporation 82801H (ICH8 Family) SMBus Controller (rev 02) 02:00.0 IDE interface: Marvell Technology Group Ltd. Unknown device 6101 (rev b1) 06:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)

with a Seagate Barracurda 7200rpm 80GB HD

I've so far tested these kernels:
2.6.20-rc5 BAD
2.6.20-rc4 BAD
2.6.19 BAD
2.6.18 BAD
2.6.17 Good !

I'll start a git-bisection...

Signature · 2 lines
	Paolo Ornati
	Linux 2.6.20-rc5 on x86_64
#1 lore raw
Quoted 62 lines · On Sun, 21 Jan 2007 15:29:32 +0100 Paolo Ornati <[email protected]> wrote:

Sorry for starting a new thread, but I've deleted the messages from my mail-box, and I'm sot sure it's the same problem as here:

	http://lkml.org/lkml/2007/1/14/108

Today I've decided to try XFS... and just doing anything on it (extracting a tarball, for example) make my SATA HD go crazy ;)

I don't remember to have seen this using Ext3.

[  877.839920] ata1.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action
0x2 frozen [  877.839929] ata1.00: cmd
61/02:00:64:98:98/00:00:00:00:00/40 tag 0 cdb 0x0 data 1024 out
[  877.839931]          res 40/00:00:00:4f:c2/00:00:00:4f:c2/00 Emask
0x4 (timeout) [  878.142367] ata1: soft resetting port [  878.351791]
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [  878.354384]
ata1.00: configured for UDMA/133 [  878.354392] ata1: EH complete
[  878.355696] SCSI device sda: 156301488 512-byte hdwr sectors
(80026 MB) [  878.355716] sda: Write Protect is off
[  878.355718] sda: Mode Sense: 00 3a 00 00
[  878.355745] SCSI device sda: write cache: enabled, read cache:

enabled, doesn't support DPO or FUA

It takes nothing to reproduce it.

My hardware is:

00:00.0 Host bridge: Intel Corporation 82P965/G965 Memory Controller Hub (rev 02) 00:02.0 VGA compatible controller: Intel Corporation 82G965 Integrated Graphics Controller (rev 02) 00:03.0 Communication
controller: Intel Corporation 82P965/G965 HECI Controller (rev 02) 00:19.0 Ethernet controller: Intel Corporation 82566DC Gigabit Network Connection (rev 02) 00:1a.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI #4 (rev 02) 00:1a.1 USB Controller:
Intel Corporation 82801H (ICH8 Family) USB UHCI #5 (rev 02) 00:1a.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI #2 (rev 02) 00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio Controller (rev 02) 00:1c.0 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 (rev 02) 00:1c.1 PCI bridge:
Intel Corporation 82801H (ICH8 Family) PCI Express Port 2 (rev 02) 00:1c.2 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 3 (rev 02) 00:1c.3 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 4 (rev 02) 00:1c.4 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 5 (rev 02) 00:1d.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI #1 (rev 02) 00:1d.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI #2 (rev 02) 00:1d.2 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI #3 (rev 02) 00:1d.7 USB
Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI #1 (rev
02) 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev f2) 00:1f.0 ISA bridge: Intel Corporation 82801HB/HR (ICH8/R) LPC Interface Controller (rev 02) 00:1f.2 SATA controller: Intel Corporation 82801HB (ICH8) 4 port SATA AHCI Controller (rev 02) 00:1f.3 SMBus: Intel Corporation 82801H (ICH8 Family) SMBus Controller (rev 02) 02:00.0 IDE interface: Marvell Technology Group Ltd. Unknown device 6101 (rev b1) 06:00.0 Ethernet controller:
Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)

with a Seagate Barracurda 7200rpm 80GB HD

Quoted 9 lines

I've so far tested these kernels:
2.6.20-rc5 BAD
2.6.20-rc4 BAD
2.6.19 BAD
2.6.18 BAD
2.6.17 Good !

I'll start a git-bisection...

git-bisect points to this commit:

----------------------------------------------

12fad3f965830d71f6454f02b2af002a64cec4d3 is first bad commit commit 12fad3f965830d71f6454f02b2af002a64cec4d3

Author: Tejun Heo <[email protected]>
Date:   Mon May 15 21:03:55 2006 +0900

[PATCH] ahci: implement NCQ suppport

Implement NCQ support.

Original implementation is from Jens Axboe.

:040000 040000 be681c4b21f34da5241e72c97c6695d735e90771
3557b2db9d7c3d48a0408137b455ce12931bb18d M drivers

----------------------------------------------

Problem just reproduced on 2.6.20-rc5:

[  431.374421] ata1.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x2 frozen
[  431.374430] ata1.00: cmd 61/40:00:fe:aa:98/00:00:00:00:00/40 tag 0 cdb 0x0 data 32768 out
[  431.374432]          res 40/00:00:9e:9c:bd/00:00:01:00:00/40 Emask 0x4 (timeout)
[  431.677154] ata1: soft resetting port
[  431.886700] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[  431.889277] ata1.00: configured for UDMA/133
[  431.889285] ata1: EH complete
[  431.890781] SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
[  431.890854] sda: Write Protect is off
[  431.890858] sda: Mode Sense: 00 3a 00 00
[  431.890903] SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[  450.800490] XFS mounting filesystem sda1
[  450.853731] Ending clean XFS mount for filesystem: sda1
[  481.131888] ata1.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x2 frozen
[  481.131896] ata1.00: cmd 61/40:00:46:af:98/00:00:00:00:00/40 tag 0 cdb 0x0 data 32768 out
[  481.131898]          res 40/00:00:9e:9c:bd/00:00:01:00:00/40 Emask 0x4 (timeout)
[  481.436015] ata1: soft resetting port
[  481.645237] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[  481.647825] ata1.00: configured for UDMA/133
[  481.647834] ata1: EH complete
[  481.649252] SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
[  481.649295] sda: Write Protect is off
[  481.649298] sda: Mode Sense: 00 3a 00 00
[  481.649358] SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA

Full dmesg attached.

If you need more info, just ask.

Signature · 2 lines
	Paolo Ornati
	Linux 2.6.20-rc5 on x86_64
[    0.000000] Linux version 2.6.20-rc5 (paolo@tux) (gcc version 4.1.1 (Gentoo 4.1.1-r1)) #12 SMP Sun Jan 21 13:31:25 CET 2007
[    0.000000] Command line: root=/dev/sda6 vga=0x305
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  BIOS-e820: 0000000000000000 - 000000000008f000 (usable)
[    0.000000]  BIOS-e820: 000000000008f000 - 00000000000a0000 (reserved)
[    0.000000]  BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 000000003e599000 (usable)
[    0.000000]  BIOS-e820: 000000003e599000 - 000000003e5a6000 (reserved)
[    0.000000]  BIOS-e820: 000000003e5a6000 - 000000003e655000 (usable)
[    0.000000]  BIOS-e820: 000000003e655000 - 000000003e6a6000 (ACPI NVS)
[    0.000000]  BIOS-e820: 000000003e6a6000 - 000000003e6ab000 (ACPI data)
[    0.000000]  BIOS-e820: 000000003e6ab000 - 000000003e6ac000 (usable)
[    0.000000]  BIOS-e820: 000000003e6ac000 - 000000003e6f2000 (ACPI NVS)
[    0.000000]  BIOS-e820: 000000003e6f2000 - 000000003e6ff000 (ACPI data)
[    0.000000]  BIOS-e820: 000000003e6ff000 - 000000003e700000 (usable)
[    0.000000]  BIOS-e820: 000000003e700000 - 000000003f000000 (reserved)
[    0.000000]  BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
[    0.000000] Entering add_active_range(0, 0, 143) 0 entries of 256 used
[    0.000000] Entering add_active_range(0, 256, 255385) 1 entries of 256 used
[    0.000000] Entering add_active_range(0, 255398, 255573) 2 entries of 256 used
[    0.000000] Entering add_active_range(0, 255659, 255660) 3 entries of 256 used
[    0.000000] Entering add_active_range(0, 255743, 255744) 4 entries of 256 used
[    0.000000] end_pfn_map = 1048576
[    0.000000] DMI 2.4 present.
[    0.000000] ACPI: RSDP (v000 INTEL                                 ) @ 0x00000000000fe020
[    0.000000] ACPI: RSDT (v001 INTEL  DG965SS  0x00000629      0x01000013) @ 0x000000003e6fd038
[    0.000000] ACPI: FADT (v001 INTEL  DG965SS  0x00000629 MSFT 0x01000013) @ 0x000000003e6fc000
[    0.000000] ACPI: MADT (v001 INTEL  DG965SS  0x00000629 MSFT 0x01000013) @ 0x000000003e6f6000
[    0.000000] ACPI: WDDT (v001 INTEL  DG965SS  0x00000629 MSFT 0x01000013) @ 0x000000003e6f5000
[    0.000000] ACPI: MCFG (v001 INTEL  DG965SS  0x00000629 MSFT 0x01000013) @ 0x000000003e6f4000
[    0.000000] ACPI: ASF! (v032 INTEL  DG965SS  0x00000629 MSFT 0x01000013) @ 0x000000003e6f3000
[    0.000000] ACPI: HPET (v001 INTEL  DG965SS  0x00000629 MSFT 0x01000013) @ 0x000000003e6f2000
[    0.000000] ACPI: SSDT (v001 INTEL     CpuPm 0x00000629 MSFT 0x01000013) @ 0x000000003e6aa000
[    0.000000] ACPI: SSDT (v001 INTEL   Cpu0Ist 0x00000629 MSFT 0x01000013) @ 0x000000003e6a9000
[    0.000000] ACPI: SSDT (v001 INTEL   Cpu1Ist 0x00000629 MSFT 0x01000013) @ 0x000000003e6a8000
[    0.000000] ACPI: SSDT (v001 INTEL   Cpu2Ist 0x00000629 MSFT 0x01000013) @ 0x000000003e6a7000
[    0.000000] ACPI: SSDT (v001 INTEL   Cpu3Ist 0x00000629 MSFT 0x01000013) @ 0x000000003e6a6000
[    0.000000] ACPI: DSDT (v001 INTEL  DG965SS  0x00000629 MSFT 0x01000013) @ 0x0000000000000000
[    0.000000] Entering add_active_range(0, 0, 143) 0 entries of 256 used
[    0.000000] Entering add_active_range(0, 256, 255385) 1 entries of 256 used
[    0.000000] Entering add_active_range(0, 255398, 255573) 2 entries of 256 used
[    0.000000] Entering add_active_range(0, 255659, 255660) 3 entries of 256 used
[    0.000000] Entering add_active_range(0, 255743, 255744) 4 entries of 256 used
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA             0 ->     4096
[    0.000000]   DMA32        4096 ->  1048576
[    0.000000]   Normal    1048576 ->  1048576
[    0.000000] early_node_map[5] active PFN ranges
[    0.000000]     0:        0 ->      143
[    0.000000]     0:      256 ->   255385
[    0.000000]     0:   255398 ->   255573
[    0.000000]     0:   255659 ->   255660
[    0.000000]     0:   255743 ->   255744
[    0.000000] On node 0 totalpages: 255449
[    0.000000]   DMA zone: 56 pages used for memmap
[    0.000000]   DMA zone: 1286 pages reserved
[    0.000000]   DMA zone: 2641 pages, LIFO batch:0
[    0.000000]   DMA32 zone: 3440 pages used for memmap
[    0.000000]   DMA32 zone: 248026 pages, LIFO batch:31
[    0.000000]   Normal zone: 0 pages used for memmap
[    0.000000] ACPI: PM-Timer IO Port: 0x408
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[    0.000000] Processor #0 (Bootup-CPU)
[    0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[    0.000000] Processor #1
[    0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled)
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1])
[    0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 2, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Setting APIC routing to flat
[    0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] Nosave address range: 000000000008f000 - 00000000000a0000
[    0.000000] Nosave address range: 00000000000a0000 - 00000000000e0000
[    0.000000] Nosave address range: 00000000000e0000 - 0000000000100000
[    0.000000] Nosave address range: 000000003e599000 - 000000003e5a6000
[    0.000000] Nosave address range: 000000003e655000 - 000000003e6a6000
[    0.000000] Nosave address range: 000000003e6a6000 - 000000003e6ab000
[    0.000000] Nosave address range: 000000003e6ac000 - 000000003e6f2000
[    0.000000] Nosave address range: 000000003e6f2000 - 000000003e6ff000
[    0.000000] Allocating PCI resources starting at 40000000 (gap: 3f000000:c0f00000)
[    0.000000] PERCPU: Allocating 32576 bytes of per cpu data
[    0.000000] Built 1 zonelists.  Total pages: 250667
[    0.000000] Kernel command line: root=/dev/sda6 vga=0x305
[    0.000000] Initializing CPU#0
[    0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes)
[   30.622927] Console: colour dummy device 80x25
[   30.623426] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
[   30.623788] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
[   30.623872] Checking aperture...
[   30.633592] Memory: 998312k/1022976k available (2871k kernel code, 22812k reserved, 1529k data, 232k init)
[   30.693254] Calibrating delay using timer specific routine.. 3732.21 BogoMIPS (lpj=1866108)
[   30.693304] Mount-cache hash table entries: 256
[   30.693409] CPU: L1 I cache: 32K, L1 D cache: 32K
[   30.693414] CPU: L2 cache: 2048K
[   30.693417] using mwait in idle threads.
[   30.693421] CPU: Physical Processor ID: 0
[   30.693423] CPU: Processor Core ID: 0
[   30.693430] CPU0: Thermal monitoring enabled (TM2)
[   30.693444] Freeing SMP alternatives: 28k freed
[   30.693461] ACPI: Core revision 20060707
[   30.708480] Using local APIC timer interrupts.
[   30.762098] result 16650020
[   30.762101] Detected 16.650 MHz APIC timer.
[   30.762330] Booting processor 1/2 APIC 0x1
[   30.772913] Initializing CPU#1
[   30.833217] Calibrating delay using timer specific routine.. 3729.62 BogoMIPS (lpj=1864812)
[   30.833224] CPU: L1 I cache: 32K, L1 D cache: 32K
[   30.833226] CPU: L2 cache: 2048K
[   30.833229] CPU: Physical Processor ID: 0
[   30.833230] CPU: Processor Core ID: 1
[   30.833236] CPU1: Thermal monitoring enabled (TM2)
[   30.833533] Intel(R) Core(TM)2 CPU          6300  @ 1.86GHz stepping 06
[   30.834228] Brought up 2 CPUs
[   30.834277] testing NMI watchdog ... OK.
[   30.844290] time.c: Using 14.318180 MHz WALL HPET GTOD HPET/TSC timer.
[   30.844294] time.c: Detected 1864.803 MHz processor.
[   30.898517] migration_cost=22
[   30.898779] NET: Registered protocol family 16
[   30.898854] ACPI: bus type pci registered
[   30.898861] PCI: Using configuration type 1
[   30.903472] ACPI: Interpreter enabled
[   30.903477] ACPI: Using IOAPIC for interrupt routing
[   30.903872] ACPI: PCI Root Bridge [PCI0] (0000:00)
[   30.903878] PCI: Probing PCI hardware (bus 00)
[   30.903895] ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
[   30.905108] Boot video device is 0000:00:02.0
[   30.905728] PCI quirk: region 0400-047f claimed by ICH6 ACPI/GPIO/TCO
[   30.905734] PCI quirk: region 0500-053f claimed by ICH6 GPIO
[   30.906325] PCI: Transparent bridge - 0000:00:1e.0
[   30.906390] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[   30.912015] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P32_._PRT]
[   30.912793] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 9 10 *11 12)
[   30.913029] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 *10 11 12)
[   30.913271] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 9 10 *11 12)
[   30.913501] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 10 *11 12)
[   30.913738] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 *9 10 11 12)
[   30.913969] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 *10 11 12)
[   30.914204] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 *9 10 11 12)
[   30.914436] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 9 10 *11 12)
[   30.916002] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT]
[   30.916265] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX1._PRT]
[   30.916519] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX2._PRT]
[   30.916773] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX3._PRT]
[   30.917026] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX4._PRT]
[   30.918512] Linux Plug and Play Support v0.97 (c) Adam Belay
[   30.918521] pnp: PnP ACPI init
[   30.921536] pnp: PnP ACPI: found 13 devices
[   30.921672] SCSI subsystem initialized
[   30.921709] libata version 2.00 loaded.
[   30.921756] usbcore: registered new interface driver usbfs
[   30.921787] usbcore: registered new interface driver hub
[   30.921824] usbcore: registered new device driver usb
[   30.921886] PCI: Using ACPI for IRQ routing
[   30.921890] PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
[   30.921974] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[   30.921981] hpet0: 3 64-bit timers, 14318180 Hz
[   30.923000] PCI-GART: No AMD northbridge found.
[   30.923060] pnp: 00:06: ioport range 0x500-0x53f has been reserved
[   30.923065] pnp: 00:06: ioport range 0x400-0x47f could not be reserved
[   30.923069] pnp: 00:06: ioport range 0x680-0x6ff has been reserved
[   30.923339] PCI: Ignore bogus resource 6 [0:0] of 0000:00:02.0
[   30.923345] PCI: Bridge: 0000:00:1c.0
[   30.923348]   IO window: disabled.
[   30.923353]   MEM window: 50400000-504fffff
[   30.923358]   PREFETCH window: disabled.
[   30.923363] PCI: Bridge: 0000:00:1c.1
[   30.923367]   IO window: 2000-2fff
[   30.923372]   MEM window: 50100000-501fffff
[   30.923376]   PREFETCH window: disabled.
[   30.923381] PCI: Bridge: 0000:00:1c.2
[   30.923384]   IO window: disabled.
[   30.923389]   MEM window: 50500000-505fffff
[   30.923393]   PREFETCH window: disabled.
[   30.923399] PCI: Bridge: 0000:00:1c.3
[   30.923401]   IO window: disabled.
[   30.923406]   MEM window: 50600000-506fffff
[   30.923411]   PREFETCH window: disabled.
[   30.923416] PCI: Bridge: 0000:00:1c.4
[   30.923418]   IO window: disabled.
[   30.923424]   MEM window: 50700000-507fffff
[   30.923428]   PREFETCH window: disabled.
[   30.923433] PCI: Bridge: 0000:00:1e.0
[   30.923437]   IO window: 1000-1fff
[   30.923442]   MEM window: 50000000-500fffff
[   30.923446]   PREFETCH window: disabled.
[   30.923467] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 17
[   30.923475] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[   30.923490] ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 16 (level, low) -> IRQ 16
[   30.923496] PCI: Setting latency timer of device 0000:00:1c.1 to 64
[   30.923511] ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 18 (level, low) -> IRQ 18
[   30.923518] PCI: Setting latency timer of device 0000:00:1c.2 to 64
[   30.923533] ACPI: PCI Interrupt 0000:00:1c.3[D] -> GSI 19 (level, low) -> IRQ 19
[   30.923539] PCI: Setting latency timer of device 0000:00:1c.3 to 64
[   30.923553] ACPI: PCI Interrupt 0000:00:1c.4[A] -> GSI 17 (level, low) -> IRQ 17
[   30.923560] PCI: Setting latency timer of device 0000:00:1c.4 to 64
[   30.923569] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[   30.923592] NET: Registered protocol family 2
[   30.936495] IP route cache hash table entries: 32768 (order: 6, 262144 bytes)
[   30.936626] TCP established hash table entries: 131072 (order: 9, 2097152 bytes)
[   30.937429] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[   30.938075] TCP: Hash tables configured (established 131072 bind 65536)
[   30.938079] TCP reno registered
[   30.941694] checking if image is initramfs...it isn't (bad gzip magic numbers); looks like an initrd
[   30.943818] Freeing initrd memory: 2000k freed
[   30.944858] IA-32 Microcode Update Driver: v1.14a <[email protected]>
[   30.945458] fuse init (API version 7.8)
[   30.945511] SGI XFS with large block/inode numbers, no debug enabled
[   30.945676] io scheduler noop registered
[   30.945689] io scheduler cfq registered (default)
[   30.946204] vesafb: framebuffer at 0x40000000, mapped to 0xffffc20000080000, using 1536k, total 7616k
[   30.946210] vesafb: mode is 1024x768x8, linelength=1024, pages=8
[   30.946214] vesafb: scrolling: redraw
[   30.946217] vesafb: Pseudocolor: size=8:8:8:8, shift=0:0:0:0
[   30.954761] Console: switching to colour frame buffer device 128x48
[   30.963319] fb0: VESA VGA frame buffer device
[   30.963456] input: Power Button (FF) as /class/input/input0
[   30.963546] ACPI: Power Button (FF) [PWRF]
[   30.963660] input: Sleep Button (CM) as /class/input/input1
[   30.963753] ACPI: Sleep Button (CM) [SLPB]
[   30.964061] ACPI: Processor [CPU0] (supports 8 throttling states)
[   30.964230] ACPI: Processor [CPU1] (supports 8 throttling states)
[   30.966361] Real Time Clock Driver v1.12ac
[   30.966471] hpet_resources: 0xfed00000 is busy
[   30.966490] Linux agpgart interface v0.101 (c) Dave Jones
[   30.966636] agpgart: Detected an Intel 965G Chipset.
[   30.967245] agpgart: Unknown page table size, assuming 512KB
[   30.967343] agpgart: Detected 7676K stolen memory.
[   30.979835] agpgart: AGP aperture is 256M @ 0x40000000
[   30.979956] [drm] Initialized drm 1.1.0 20060810
[   30.980047] ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 16
[   30.980221] [drm] Initialized i915 1.6.0 20060119 on minor 0
[   30.980313] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
[   30.980544] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[   30.982444] 00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[   30.984136] Floppy drive(s): fd0 is 1.44M
[   30.999821] FDC 0 is a National Semiconductor PC87306
[   31.002866] RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
[   31.004881] loop: loaded (max 8 devices)
[   31.006710] Intel(R) PRO/10GbE Network Driver - version 1.0.126-k2
[   31.008648] Copyright (c) 1999-2006 Intel Corporation.
[   31.010866] 8139too Fast Ethernet driver 0.9.28
[   31.012935] ACPI: PCI Interrupt 0000:06:00.0[A] -> GSI 21 (level, low) -> IRQ 21
[   31.015439] eth0: RealTek RTL8139 at 0xffffc2000000e000, 00:e0:4c:f0:a9:84, IRQ 21
[   31.017719] eth0:  Identified 8139 chip type 'RTL-8139C'
[   31.017724] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[   31.020080] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[   31.022624] Probing IDE interface ide0...
[   31.536077] Probing IDE interface ide1...
[   32.049444] ahci 0000:00:1f.2: version 2.0
[   32.049457] ACPI: PCI Interrupt 0000:00:1f.2[A] -> GSI 19 (level, low) -> IRQ 19
[   33.053438] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[   33.053445] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0x33 impl SATA mode
[   33.056162] ahci 0000:00:1f.2: flags: 64bit ncq led clo pio slum part 
[   33.058971] ata1: SATA max UDMA/133 cmd 0xFFFFC20000024100 ctl 0x0 bmdma 0x0 irq 19
[   33.061879] ata2: SATA max UDMA/133 cmd 0xFFFFC20000024180 ctl 0x0 bmdma 0x0 irq 19
[   33.064763] ata3: DUMMY
[   33.067649] ata4: DUMMY
[   33.070574] ata5: SATA max UDMA/133 cmd 0xFFFFC20000024300 ctl 0x0 bmdma 0x0 irq 19
[   33.073666] ata6: SATA max UDMA/133 cmd 0xFFFFC20000024380 ctl 0x0 bmdma 0x0 irq 19
[   33.076718] scsi0 : ahci
[   33.537612] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[   33.541952] ata1.00: ATA-6, max UDMA/133, 156301488 sectors: LBA48 NCQ (depth 31/32)
[   33.546612] ata1.00: configured for UDMA/133
[   33.549812] scsi1 : ahci
[   33.856779] ata2: SATA link down (SStatus 0 SControl 300)
[   33.859895] scsi2 : ahci
[   33.863049] scsi3 : ahci
[   33.866148] scsi4 : ahci
[   34.171860] ata5: SATA link down (SStatus 0 SControl 300)
[   34.174931] scsi5 : ahci
[   34.480952] ata6: SATA link down (SStatus 0 SControl 300)
[   34.484083] scsi 0:0:0:0: Direct-Access     ATA      ST380817AS       3.42 PQ: 0 ANSI: 5
[   34.487315] SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
[   34.490502] sda: Write Protect is off
[   34.493660] sda: Mode Sense: 00 3a 00 00
[   34.493675] SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   34.497010] SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
[   34.500315] sda: Write Protect is off
[   34.503558] sda: Mode Sense: 00 3a 00 00
[   34.503573] SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   34.506920]  sda: sda1 sda2 < sda5 sda6 sda7 sda8 >
[   34.570981] sd 0:0:0:0: Attached scsi disk sda
[   34.574292] sd 0:0:0:0: Attached scsi generic sg0 type 0
[   34.577577] ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 17 (level, low) -> IRQ 17
[   34.580884] PCI: Setting latency timer of device 0000:02:00.0 to 64
[   34.580903] ata7: PATA max UDMA/100 cmd 0x2018 ctl 0x2026 bmdma 0x2000 irq 17
[   34.584160] scsi6 : pata_marvell
[   34.587447] BAR5:00:00 01:7F 02:22 03:CA 04:00 05:00 06:00 07:00 08:00 09:00 0A:00 0B:00 0C:01 0D:00 0E:00 0F:00 
[   34.754096] ATA: abnormal status 0x8 on port 0x201F
[   34.769209] ATA: abnormal status 0x8 on port 0x201F
[   34.943029] ata7.01: ATAPI, max UDMA/33
[   35.117489] ata7.01: configured for UDMA/33
[   35.124371] scsi 6:0:1:0: CD-ROM            HL-DT-ST DVDRAM GSA-4167B DL11 PQ: 0 ANSI: 5
[   35.146129] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[   35.149422] Uniform CD-ROM driver Revision: 3.20
[   35.152680] sr 6:0:1:0: Attached scsi CD-ROM sr0
[   35.152733] sr 6:0:1:0: Attached scsi generic sg1 type 5
[   35.155964] ACPI: PCI Interrupt 0000:00:1a.7[C] -> GSI 18 (level, low) -> IRQ 18
[   35.159175] PCI: Setting latency timer of device 0000:00:1a.7 to 64
[   35.159179] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[   35.162397] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
[   35.165598] ehci_hcd 0000:00:1a.7: debug port 1
[   35.168784] PCI: cache line size of 32 is not supported by device 0000:00:1a.7
[   35.168791] ehci_hcd 0000:00:1a.7: irq 18, io mem 0x50325c00
[   35.175808] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[   35.179141] usb usb1: configuration #1 chosen from 1 choice
[   35.182385] hub 1-0:1.0: USB hub found
[   35.185625] hub 1-0:1.0: 4 ports detected
[   35.289849] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 23
[   35.293120] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[   35.293123] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[   35.296363] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
[   35.299612] ehci_hcd 0000:00:1d.7: debug port 1
[   35.302811] PCI: cache line size of 32 is not supported by device 0000:00:1d.7
[   35.302818] ehci_hcd 0000:00:1d.7: irq 23, io mem 0x50325800
[   35.309902] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[   35.313202] usb usb2: configuration #1 chosen from 1 choice
[   35.316505] hub 2-0:1.0: USB hub found
[   35.319802] hub 2-0:1.0: 6 ports detected
[   35.423852] USB Universal Host Controller Interface driver v3.0
[   35.427206] ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 16 (level, low) -> IRQ 16
[   35.430572] PCI: Setting latency timer of device 0000:00:1a.0 to 64
[   35.430575] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[   35.433925] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
[   35.437262] uhci_hcd 0000:00:1a.0: irq 16, io base 0x000030c0
[   35.440634] usb usb3: configuration #1 chosen from 1 choice
[   35.443886] hub 3-0:1.0: USB hub found
[   35.447056] hub 3-0:1.0: 2 ports detected
[   35.551901] ACPI: PCI Interrupt 0000:00:1a.1[B] -> GSI 21 (level, low) -> IRQ 21
[   35.555078] PCI: Setting latency timer of device 0000:00:1a.1 to 64
[   35.555081] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[   35.558204] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
[   35.561364] uhci_hcd 0000:00:1a.1: irq 21, io base 0x000030a0
[   35.564605] usb usb4: configuration #1 chosen from 1 choice
[   35.567757] hub 4-0:1.0: USB hub found
[   35.570823] hub 4-0:1.0: 2 ports detected
[   35.674942] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 23
[   35.677998] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[   35.678001] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[   35.680990] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 5
[   35.684056] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00003080
[   35.687166] usb usb5: configuration #1 chosen from 1 choice
[   35.690247] hub 5-0:1.0: USB hub found
[   35.693235] hub 5-0:1.0: 2 ports detected
[   35.797979] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19
[   35.800971] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[   35.800974] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[   35.803973] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 6
[   35.806959] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00003060
[   35.809972] usb usb6: configuration #1 chosen from 1 choice
[   35.812916] hub 6-0:1.0: USB hub found
[   35.815806] hub 6-0:1.0: 2 ports detected
[   35.920021] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
[   35.922994] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[   35.922997] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[   35.925960] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 7
[   35.928932] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00003040
[   35.931994] usb usb7: configuration #1 chosen from 1 choice
[   35.934965] hub 7-0:1.0: USB hub found
[   35.937844] hub 7-0:1.0: 2 ports detected
[   36.042093] usbcore: registered new interface driver cdc_acm
[   36.044991] drivers/usb/class/cdc-acm.c: v0.25:USB Abstract Control Model driver for USB modems and ISDN adapters
[   36.048065] usbcore: registered new interface driver usblp
[   36.051105] drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
[   36.054174] Initializing USB Mass Storage driver...
[   36.057250] usbcore: registered new interface driver usb-storage
[   36.060363] USB Mass Storage support registered.
[   36.063533] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
[   36.069536] serio: i8042 KBD port at 0x60,0x64 irq 1
[   36.072646] serio: i8042 AUX port at 0x60,0x64 irq 12
[   36.075753] mice: PS/2 mouse device common for all mice
[   36.078970] i2c /dev entries driver
[   36.082061] ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 21 (level, low) -> IRQ 21
[   36.105452] EDAC MC: Ver: 2.0.1 Jan 21 2007
[   36.108861] Advanced Linux Sound Architecture Driver Version 1.0.14rc1 (Tue Jan 09 09:56:17 2007 UTC).
[   36.112489] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 22
[   36.115735] PCI: Setting latency timer of device 0000:00:1b.0 to 64
[   36.236274] ALSA device list:
[   36.239468]   #0: HDA Intel at 0x50320000 irq 22
[   36.242691] nf_conntrack version 0.5.0 (3996 buckets, 31968 max)
[   36.246129] ip_tables: (C) 2000-2006 Netfilter Core Team
[   36.292245] TCP cubic registered
[   36.295496] NET: Registered protocol family 1
[   36.298716] NET: Registered protocol family 17
[   36.301848] NET: Registered protocol family 15
[   36.817332] input: ImPS/2 Logitech Wheel Mouse as /class/input/input2
[   36.844024] input: AT Translated Set 2 keyboard as /class/input/input3
[   36.911624] RAMDISK: ext2 filesystem found at block 0
[   36.914791] RAMDISK: Loading 2000KiB [1 disk] into ram disk... |/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|done.
[   36.922467] VFS: Mounted root (ext2 filesystem).
[   36.946396] kjournald starting.  Commit interval 5 seconds
[   36.946405] EXT3-fs: mounted filesystem with ordered data mode.
[   36.946440] VFS: Mounted root (ext3 filesystem) readonly.
[   36.946442] Trying to move old root to /initrd ... /initrd does not exist. Ignored.
[   36.946615] Unmounting old root
[   36.946720] Trying to free ramdisk memory ... okay
[   36.946984] Freeing unused kernel memory: 232k freed
[   41.104813] EXT3 FS on sda6, internal journal
[   41.550123] Adding 1004016k swap on /dev/sda7.  Priority:-1 extents:1 across:1004016k
[   62.630799] eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
[  399.563221] XFS mounting filesystem sda1
[  399.603500] Ending clean XFS mount for filesystem: sda1
[  431.374421] ata1.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x2 frozen
[  431.374430] ata1.00: cmd 61/40:00:fe:aa:98/00:00:00:00:00/40 tag 0 cdb 0x0 data 32768 out
[  431.374432]          res 40/00:00:9e:9c:bd/00:00:01:00:00/40 Emask 0x4 (timeout)
[  431.677154] ata1: soft resetting port
[  431.886700] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[  431.889277] ata1.00: configured for UDMA/133
[  431.889285] ata1: EH complete
[  431.890781] SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
[  431.890854] sda: Write Protect is off
[  431.890858] sda: Mode Sense: 00 3a 00 00
[  431.890903] SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[  450.800490] XFS mounting filesystem sda1
[  450.853731] Ending clean XFS mount for filesystem: sda1
[  481.131888] ata1.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x2 frozen
[  481.131896] ata1.00: cmd 61/40:00:46:af:98/00:00:00:00:00/40 tag 0 cdb 0x0 data 32768 out
[  481.131898]          res 40/00:00:9e:9c:bd/00:00:01:00:00/40 Emask 0x4 (timeout)
[  481.436015] ata1: soft resetting port
[  481.645237] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[  481.647825] ata1.00: configured for UDMA/133
[  481.647834] ata1: EH complete
[  481.649252] SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
[  481.649295] sda: Write Protect is off
[  481.649298] sda: Mode Sense: 00 3a 00 00
[  481.649358] SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
           CPU0       CPU1       
  0:     617966          0   IO-APIC-edge      timer
  1:       2361          0   IO-APIC-edge      i8042
  6:          5          0   IO-APIC-edge      floppy
  8:          1          0   IO-APIC-edge      rtc
  9:          0          0   IO-APIC-fasteoi   acpi
 12:      28043          0   IO-APIC-edge      i8042
 16:      43984          0   IO-APIC-fasteoi   uhci_hcd:usb3, i915@pci:0000:00:02.0
 17:       6551          0   IO-APIC-fasteoi   libata
 18:          0          0   IO-APIC-fasteoi   ehci_hcd:usb1, uhci_hcd:usb7
 19:       9176          0   IO-APIC-fasteoi   libata, uhci_hcd:usb6
 21:        375          0   IO-APIC-fasteoi   uhci_hcd:usb4, eth0
 22:        192          0   IO-APIC-fasteoi   HDA Intel
 23:          0          0   IO-APIC-fasteoi   ehci_hcd:usb2, uhci_hcd:usb5
NMI:        170         85 
LOC:     605529     605586 
ERR:          0

00:00.0 Host bridge: Intel Corporation 82P965/G965 Memory Controller Hub (rev 02) 00:02.0 VGA compatible controller: Intel Corporation 82G965 Integrated Graphics Controller (rev 02) 00:03.0 Communication controller: Intel Corporation 82P965/G965 HECI Controller (rev 02) 00:19.0 Ethernet controller: Intel Corporation 82566DC Gigabit Network Connection (rev 02) 00:1a.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI #4 (rev 02) 00:1a.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI #5 (rev 02) 00:1a.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI #2 (rev 02) 00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio Controller (rev 02) 00:1c.0 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 (rev 02) 00:1c.1 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 2 (rev 02) 00:1c.2 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 3 (rev 02) 00:1c.3 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 4 (rev 02) 00:1c.4 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 5 (rev 02) 00:1d.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI #1 (rev 02) 00:1d.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI #2 (rev 02) 00:1d.2 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI #3 (rev 02) 00:1d.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI #1 (rev 02) 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev f2)
00:1f.0 ISA bridge: Intel Corporation 82801HB/HR (ICH8/R) LPC Interface Controller (rev 02) 00:1f.2 SATA controller: Intel Corporation 82801HB (ICH8) 4 port SATA AHCI Controller (rev 02) 00:1f.3 SMBus: Intel Corporation 82801H (ICH8 Family) SMBus Controller (rev 02) 02:00.0 IDE interface: Marvell Technology Group Ltd. Unknown device 6101 (rev b1) 06:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)

#2 lore raw
Quoted 27 lines · Paolo Ornati
Quoted 24 lines · On Sun, 21 Jan 2007 15:29:32 +0100 Paolo Ornati <[email protected]> wrote:

Sorry for starting a new thread, but I've deleted the messages from my mail-box, and I'm sot sure it's the same problem as here:

	http://lkml.org/lkml/2007/1/14/108

Today I've decided to try XFS... and just doing anything on it (extracting a tarball, for example) make my SATA HD go crazy ;)

I don't remember to have seen this using Ext3.

[  877.839920] ata1.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action
0x2 frozen [  877.839929] ata1.00: cmd
61/02:00:64:98:98/00:00:00:00:00/40 tag 0 cdb 0x0 data 1024 out
[  877.839931]          res 40/00:00:00:4f:c2/00:00:00:4f:c2/00 Emask
0x4 (timeout) [  878.142367] ata1: soft resetting port [  878.351791]
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [  878.354384]
ata1.00: configured for UDMA/133 [  878.354392] ata1: EH complete
[  878.355696] SCSI device sda: 156301488 512-byte hdwr sectors
(80026 MB) [  878.355716] sda: Write Protect is off
[  878.355718] sda: Mode Sense: 00 3a 00 00
[  878.355745] SCSI device sda: write cache: enabled, read cache:

enabled, doesn't support DPO or FUA

It takes nothing to reproduce it.

..

Quoted 4 lines

git-bisect points to this commit:

----------------------------------------------

Quoted 8 lines

12fad3f965830d71f6454f02b2af002a64cec4d3 is first bad commit commit 12fad3f965830d71f6454f02b2af002a64cec4d3

Author: Tejun Heo <[email protected]>
Date:   Mon May 15 21:03:55 2006 +0900

[PATCH] ahci: implement NCQ suppport

Implement NCQ support.

It looks like what you're getting is an actual NCQ write timing out. That makes the bisect result not very interesting since obviously it wouldn't have issued any NCQ writes before NCQ support was implemented. Seeing as how it's also an entirely different driver I imagine it's a different problem than what I've been looking at.

Maybe that drive just has some issues with NCQ? I would be surprised at that with a Seagate though..

Signature · 3 lines
Robert Hancock      Saskatoon, SK, Canada
To email, remove "nospam" from [email protected]
Home Page: http://www.roberthancock.com/
#3 lore raw
Quoted 8 lines · On Sun, 21 Jan 2007 11:32:02 -0600 Robert Hancock <[email protected]> wrote:

It looks like what you're getting is an actual NCQ write timing out. That makes the bisect result not very interesting since obviously it wouldn't have issued any NCQ writes before NCQ support was implemented. Seeing as how it's also an entirely different driver I imagine it's a different problem than what I've been looking at.

Maybe that drive just has some issues with NCQ? I would be surprised at that with a Seagate though..

I don't know. It's a two years old ST380817AS.

# smartctl -a -d ata /dev/sda

smartctl version 5.36 [x86_64-pc-linux-gnu] Copyright (C) 2002-6 Bruce Allen Home page is http://smartmontools.sourceforge.net/

=== START OF INFORMATION SECTION ===

Model Family:     Seagate Barracuda 7200.7 and 7200.7 Plus family
Device Model:     ST380817AS
Serial Number:    4MR08EK8
Firmware Version: 3.42
User Capacity:    80,026,361,856 bytes
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   6
ATA Standard is:  ATA/ATAPI-6 T13 1410D revision 2
Local Time is:    Sun Jan 21 20:15:40 2007 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error. Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever been run.
Total time to complete Offline
data collection: ( 430) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support. Suspend Offline collection upon new command.
Offline surface scan supported. Self-test supported.
No Conveyance Self-test supported. Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 47) minutes.

SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds:

ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000f   059   049   006    Pre-fail  Always       -       215927244
  3 Spin_Up_Time            0x0003   098   098   000    Pre-fail  Always       -       0
  4 Start_Stop_Count        0x0032   098   098   020    Old_age   Always       -       2182
  5 Reallocated_Sector_Ct   0x0033   100   100   036    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x000f   083   060   030    Pre-fail  Always       -       204305750
  9 Power_On_Hours          0x0032   097   097   000    Old_age   Always       -       3494
 10 Spin_Retry_Count        0x0013   100   100   097    Pre-fail  Always       -       0
 12 Power_Cycle_Count       0x0032   098   098   020    Old_age   Always       -       2541
194 Temperature_Celsius     0x0022   024   040   000    Old_age   Always       -       24 (Lifetime Min/Max 0/15)
195 Hardware_ECC_Recovered  0x001a   059   049   000    Old_age   Always       -       215927244
197 Current_Pending_Sector  0x0012   100   100   000    Old_age   Always       -       1
198 Offline_Uncorrectable   0x0010   100   100   000    Old_age   Offline      -       1
199 UDMA_CRC_Error_Count    0x003e   200   200   000    Old_age   Always       -       0
200 Multi_Zone_Error_Rate   0x0000   100   253   000    Old_age   Offline      -       0
202 TA_Increase_Count       0x0032   100   253   000    Old_age   Always       -       0

SMART Error Log Version: 1
ATA Error Count: 12 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 12 occurred at disk power-on lifetime: 2516 hours (104 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 0d 5b 9d 34 e1 Error: UNC 13 sectors at LBA = 0x01349d5b = 20225371

Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  c8 00 00 4e 9d 34 e1 00      00:03:03.851  READ DMA
  c8 00 00 4e 9d 34 e1 00      00:03:03.848  READ DMA
  c8 00 00 4e 9d 34 e1 00      00:03:03.846  READ DMA
  c8 00 00 4e 9d 34 e1 00      00:03:03.843  READ DMA
  c8 00 00 4e 9d 34 e1 00      00:03:03.839  READ DMA

Error 11 occurred at disk power-on lifetime: 2516 hours (104 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 0d 5b 9d 34 e1 Error: UNC 13 sectors at LBA = 0x01349d5b = 20225371

Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  c8 00 00 4e 9d 34 e1 00      00:03:03.851  READ DMA
  c8 00 00 4e 9d 34 e1 00      00:03:03.848  READ DMA
  c8 00 00 4e 9d 34 e1 00      00:03:03.846  READ DMA
  c8 00 00 4e 9d 34 e1 00      00:03:03.843  READ DMA
  c8 00 00 4e 9d 34 e1 00      00:03:03.839  READ DMA

Error 10 occurred at disk power-on lifetime: 2516 hours (104 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 0d 5b 9d 34 e1 Error: UNC 13 sectors at LBA = 0x01349d5b = 20225371

Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  c8 00 00 4e 9d 34 e1 00      00:03:03.851  READ DMA
  c8 00 00 4e 9d 34 e1 00      00:03:03.848  READ DMA
  c8 00 00 4e 9d 34 e1 00      00:03:03.846  READ DMA
  c8 00 00 4e 9d 34 e1 00      00:03:03.843  READ DMA
  c8 00 00 16 9c 34 e1 00      00:03:03.839  READ DMA

Error 9 occurred at disk power-on lifetime: 2516 hours (104 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 0d 5b 9d 34 e1 Error: UNC 13 sectors at LBA = 0x01349d5b = 20225371

Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  c8 00 00 4e 9d 34 e1 00      00:03:03.851  READ DMA
  c8 00 00 4e 9d 34 e1 00      00:03:03.848  READ DMA
  c8 00 00 4e 9d 34 e1 00      00:03:03.846  READ DMA
  c8 00 00 16 9c 34 e1 00      00:03:03.843  READ DMA
  c8 00 00 0e 9b 34 e1 00      00:03:03.839  READ DMA

Error 8 occurred at disk power-on lifetime: 2516 hours (104 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 0d 5b 9d 34 e1 Error: UNC 13 sectors at LBA = 0x01349d5b = 20225371

Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  c8 00 00 4e 9d 34 e1 00      00:03:03.851  READ DMA
  c8 00 00 4e 9d 34 e1 00      00:03:03.848  READ DMA
  c8 00 00 16 9c 34 e1 00      00:03:03.846  READ DMA
  c8 00 00 0e 9b 34 e1 00      00:03:03.843  READ DMA
  c8 00 00 8e 99 34 e1 00      00:03:03.839  READ DMA

SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]

SMART Selective self-test log data structure revision number 1

 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing

Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

Signature · 2 lines
	Paolo Ornati
	Linux 2.6.20-rc5 on x86_64
#4 lore raw
Quoted 195 lines · Paolo Ornati
Quoted 8 lines · On Sun, 21 Jan 2007 11:32:02 -0600 Robert Hancock <[email protected]> wrote:

It looks like what you're getting is an actual NCQ write timing out. That makes the bisect result not very interesting since obviously it wouldn't have issued any NCQ writes before NCQ support was implemented. Seeing as how it's also an entirely different driver I imagine it's a different problem than what I've been looking at.

Maybe that drive just has some issues with NCQ? I would be surprised at that with a Seagate though..

I don't know. It's a two years old ST380817AS.

# smartctl -a -d ata /dev/sda

smartctl version 5.36 [x86_64-pc-linux-gnu] Copyright (C) 2002-6 Bruce Allen Home page is http://smartmontools.sourceforge.net/

=== START OF INFORMATION SECTION ===

Model Family:     Seagate Barracuda 7200.7 and 7200.7 Plus family
Device Model:     ST380817AS
Serial Number:    4MR08EK8
Firmware Version: 3.42
User Capacity:    80,026,361,856 bytes
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   6
ATA Standard is:  ATA/ATAPI-6 T13 1410D revision 2
Local Time is:    Sun Jan 21 20:15:40 2007 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error. Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever been run.
Total time to complete Offline
data collection: ( 430) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support. Suspend Offline collection upon new command.
Offline surface scan supported. Self-test supported.
No Conveyance Self-test supported. Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 47) minutes.

SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds:

ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000f   059   049   006    Pre-fail  Always       -       215927244
  3 Spin_Up_Time            0x0003   098   098   000    Pre-fail  Always       -       0
  4 Start_Stop_Count        0x0032   098   098   020    Old_age   Always       -       2182
  5 Reallocated_Sector_Ct   0x0033   100   100   036    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x000f   083   060   030    Pre-fail  Always       -       204305750
  9 Power_On_Hours          0x0032   097   097   000    Old_age   Always       -       3494
 10 Spin_Retry_Count        0x0013   100   100   097    Pre-fail  Always       -       0
 12 Power_Cycle_Count       0x0032   098   098   020    Old_age   Always       -       2541
194 Temperature_Celsius     0x0022   024   040   000    Old_age   Always       -       24 (Lifetime Min/Max 0/15)
195 Hardware_ECC_Recovered  0x001a   059   049   000    Old_age   Always       -       215927244
197 Current_Pending_Sector  0x0012   100   100   000    Old_age   Always       -       1
198 Offline_Uncorrectable   0x0010   100   100   000    Old_age   Offline      -       1
199 UDMA_CRC_Error_Count    0x003e   200   200   000    Old_age   Always       -       0
200 Multi_Zone_Error_Rate   0x0000   100   253   000    Old_age   Offline      -       0
202 TA_Increase_Count       0x0032   100   253   000    Old_age   Always       -       0

SMART Error Log Version: 1
ATA Error Count: 12 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 12 occurred at disk power-on lifetime: 2516 hours (104 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 0d 5b 9d 34 e1 Error: UNC 13 sectors at LBA = 0x01349d5b = 20225371

Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  c8 00 00 4e 9d 34 e1 00      00:03:03.851  READ DMA
  c8 00 00 4e 9d 34 e1 00      00:03:03.848  READ DMA
  c8 00 00 4e 9d 34 e1 00      00:03:03.846  READ DMA
  c8 00 00 4e 9d 34 e1 00      00:03:03.843  READ DMA
  c8 00 00 4e 9d 34 e1 00      00:03:03.839  READ DMA

Error 11 occurred at disk power-on lifetime: 2516 hours (104 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 0d 5b 9d 34 e1 Error: UNC 13 sectors at LBA = 0x01349d5b = 20225371

Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  c8 00 00 4e 9d 34 e1 00      00:03:03.851  READ DMA
  c8 00 00 4e 9d 34 e1 00      00:03:03.848  READ DMA
  c8 00 00 4e 9d 34 e1 00      00:03:03.846  READ DMA
  c8 00 00 4e 9d 34 e1 00      00:03:03.843  READ DMA
  c8 00 00 4e 9d 34 e1 00      00:03:03.839  READ DMA

Error 10 occurred at disk power-on lifetime: 2516 hours (104 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 0d 5b 9d 34 e1 Error: UNC 13 sectors at LBA = 0x01349d5b = 20225371

Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  c8 00 00 4e 9d 34 e1 00      00:03:03.851  READ DMA
  c8 00 00 4e 9d 34 e1 00      00:03:03.848  READ DMA
  c8 00 00 4e 9d 34 e1 00      00:03:03.846  READ DMA
  c8 00 00 4e 9d 34 e1 00      00:03:03.843  READ DMA
  c8 00 00 16 9c 34 e1 00      00:03:03.839  READ DMA

Error 9 occurred at disk power-on lifetime: 2516 hours (104 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 0d 5b 9d 34 e1 Error: UNC 13 sectors at LBA = 0x01349d5b = 20225371

Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  c8 00 00 4e 9d 34 e1 00      00:03:03.851  READ DMA
  c8 00 00 4e 9d 34 e1 00      00:03:03.848  READ DMA
  c8 00 00 4e 9d 34 e1 00      00:03:03.846  READ DMA
  c8 00 00 16 9c 34 e1 00      00:03:03.843  READ DMA
  c8 00 00 0e 9b 34 e1 00      00:03:03.839  READ DMA

Error 8 occurred at disk power-on lifetime: 2516 hours (104 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 0d 5b 9d 34 e1 Error: UNC 13 sectors at LBA = 0x01349d5b = 20225371

Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  c8 00 00 4e 9d 34 e1 00      00:03:03.851  READ DMA
  c8 00 00 4e 9d 34 e1 00      00:03:03.848  READ DMA
  c8 00 00 16 9c 34 e1 00      00:03:03.846  READ DMA
  c8 00 00 0e 9b 34 e1 00      00:03:03.843  READ DMA
  c8 00 00 8e 99 34 e1 00      00:03:03.839  READ DMA

SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]

SMART Selective self-test log data structure revision number 1

 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Quoted 4 lines

Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

(Added myself to CC.)

Quoted 3 lines
  7 Seek_Error_Rate         0x000f   083   060   030    Pre-fail  Always       -       204305750
  1 Raw_Read_Error_Rate     0x000f   059   049   006    Pre-fail  Always       -       215927244
195 Hardware_ECC_Recovered  0x001a   059   049   000    Old_age   Always       -       215927244 

Wow! that HDD is really in a bad condition.

Thanks,
Chr.

#5 lore raw
Quoted 5 lines · Chr
Quoted 3 lines
  7 Seek_Error_Rate         0x000f   083   060   030    Pre-fail  Always       -       204305750
  1 Raw_Read_Error_Rate     0x000f   059   049   006    Pre-fail  Always       -       215927244
195 Hardware_ECC_Recovered  0x001a   059   049   000    Old_age   Always       -       215927244 

Wow! that HDD is really in a bad condition.

I don't think so, this seems to be normal for Seagate drives...

regards,

Signature · 4 lines
http://www.fi.muni.cz/~xslaby/            Jiri Slaby
faculty of informatics, masaryk university, brno, cz
e-mail: jirislaby gmail com, gpg pubkey fingerprint:
B674 9967 0407 CE62 ACC8  22A0 32CC 55C3 39D4 7A7E
#7 lore raw
In reply to Paolo Ornati
Quoted 10 lines · Paolo Ornati

I don't know. It's a two years old ST380817AS.

# smartctl -a -d ata /dev/sda

smartctl version 5.36 [x86_64-pc-linux-gnu] Copyright (C) 2002-6 Bruce Allen Home page is http://smartmontools.sourceforge.net/

=== START OF INFORMATION SECTION ===

Model Family:     Seagate Barracuda 7200.7 and 7200.7 Plus family
Device Model:     ST380817AS

I'll blacklist it. Thanks.

Signature · 1 line
tejun
#6 lore raw
In reply to Jiri Slaby
Quoted 7 lines · On Mon, 22 Jan 2007 01:53:21 +0059 Jiri Slaby <[email protected]> wrote:
Quoted 5 lines
Quoted 3 lines
  7 Seek_Error_Rate         0x000f   083   060   030    Pre-fail  Always       -       204305750
  1 Raw_Read_Error_Rate     0x000f   059   049   006    Pre-fail  Always       -       215927244
195 Hardware_ECC_Recovered  0x001a   059   049   000    Old_age   Always       -       215927244 

Wow! that HDD is really in a bad condition.

I don't think so, this seems to be normal for Seagate drives...

I agree.

For Chr: I don't think these big raw-numbers are counters, look at the normalized values instead, and see that they are greater than TRESH values (so they are good).

The meaning of raw-numbers is vendor specific.

Signature · 2 lines
	Paolo Ornati
	Linux 2.6.20-rc5 on x86_64
#8 lore raw
In reply to Tejun Heo
Quoted 4 lines · On Mon, 22 Jan 2007 11:46:01 +0900 Tejun Heo <[email protected]> wrote:
Quoted 4 lines

I don't know. It's a two years old ST380817AS.

# smartctl -a -d ata /dev/sda
Quoted 8 lines
Quoted 6 lines

smartctl version 5.36 [x86_64-pc-linux-gnu] Copyright (C) 2002-6 Bruce Allen Home page is http://smartmontools.sourceforge.net/

=== START OF INFORMATION SECTION ===

Model Family:     Seagate Barracuda 7200.7 and 7200.7 Plus family
Device Model:     ST380817AS

I'll blacklist it. Thanks.

Ok. It will be better if someone else with the same HD could confirm.

It looks so strange that an HD that works fine, and should support NCQ, have so big troubles that I can "freeze" it in less than a second by using XFS (while with ext3 I cannot, or at least it's very hard).

Signature · 2 lines
	Paolo Ornati
	Linux 2.6.20-rc5 on x86_64
#9 lore raw
Quoted 10 lines · Paolo Ornati
Quoted 4 lines
Quoted 3 lines

=== START OF INFORMATION SECTION ===

Model Family:     Seagate Barracuda 7200.7 and 7200.7 Plus family
Device Model:     ST380817AS

I'll blacklist it. Thanks.

Ok. It will be better if someone else with the same HD could confirm.

It looks so strange that an HD that works fine, and should support NCQ, have so big troubles that I can "freeze" it in less than a second by using XFS (while with ext3 I cannot, or at least it's very hard).

Yeap, certainly. I'll ask people first before actually proceeding with the blacklisting. I'm just getting a bit tired of tides of NCQ firmware problems.

Anyways, for the time being, you can easily turn off NCQ using sysfs. Please take a look at http://linux-ata.org/faq.html

Signature · 1 line
tejun
#10 lore raw
Quoted 6 lines · On Mon, 22 Jan 2007 18:35:05 +0900 Tejun Heo <[email protected]> wrote:

Yeap, certainly. I'll ask people first before actually proceeding with the blacklisting. I'm just getting a bit tired of tides of NCQ firmware problems.

Anyways, for the time being, you can easily turn off NCQ using sysfs. Please take a look at http://linux-ata.org/faq.html

ok

Signature · 2 lines
	Paolo Ornati
	Linux 2.6.20-rc5 on x86_64
#11 lore raw
In reply to Tejun Heo
Quoted 3 lines · On Mon, 22 Jan 2007 18:35:05 +0900 Tejun Heo <[email protected]> wrote:

Yeap, certainly. I'll ask people first before actually proceeding with the blacklisting. I'm just getting a bit tired of tides of NCQ firmware problems.

Another interesting thing: it seems that I'm unable to reproduce the problem mounting XFS with "nobarrier" (using sda queue_depth = 31).

So it looks like a problem with NCQ combined with cache flush command...

Signature · 2 lines
	Paolo Ornati
	Linux 2.6.20-rc5 on x86_64