Add support for Seeq 8003 on Challenge S Mezz board.
Subsystems (2)
From: Ladislav Michl <[email protected]>
Thanks to Jö Fahlke for donating hardware.
Signed-off-by Ladislav Michl <[email protected]>
Forward porting of Ladis' 2.4 patch.
Signed-off-by Ralf Baechle <[email protected]>
drivers/net/sgiseeq.c +25 -3
@@ -625,7 +625,7 @@ static inline void setup_rx_ring(struct sgiseeq_rx_desc *buf, int nbufs)#define ALIGNED (x) ((((unsigned long)(x)) + 0xf) & ~(0xf)) -static int sgiseeq_init (struct hpc3_regs * hpcregs,int irq) +static int sgiseeq_init (struct hpc3_regs * hpcregs,int irq,int has_eeprom) {struct sgiseeq_init_block *sr;struct sgiseeq_private *sp;
@@ -651,7 +651,9 @@ static int sgiseeq_init(struct hpc3_regs* hpcregs, int irq)#define EADDR_NVOFS 250for (i =0 ; i <3 ; i++) { -unsigned short tmp =ip22_nvram_read (EADDR_NVOFS /2 + i); +unsigned short tmp = has_eeprom ? +ip22_eeprom_read (&hpcregs->eeprom,EADDR_NVOFS /2 +i) : +ip22_nvram_read (EADDR_NVOFS /2 +i); dev->dev_addr[2 * i] = tmp >>8 ; dev->dev_addr[2 * i +1 ] = tmp &0xff ;
@@ -684,6 +686,11 @@ static int sgiseeq_init(struct hpc3_regs* hpcregs, int irq) sp->hregs->dconfig =HPC3_EDCFG_FIRQ |HPC3_EDCFG_FEOP |HPC3_EDCFG_FRXDC |HPC3_EDCFG_PTO |0x026 ; +/* Setup PIO and DMA transfer timing */ + sp->hregs->pconfig =0x161 ; + sp->hregs->dconfig =HPC3_EDCFG_FIRQ |HPC3_EDCFG_FEOP | +HPC3_EDCFG_FRXDC |HPC3_EDCFG_PTO |0x026 ; +/* Reset the chip. */ hpc3_eth_reset (sp->hregs);
@@ -730,8 +737,23 @@ err_out:static int __init sgiseeq_probe (void ) { +unsigned int tmp, ret1, ret2 =0 ; +/* On board adapter on 1st HPC is always present */ -return sgiseeq_init (hpc3c0,SGI_ENET_IRQ ); + ret1 =sgiseeq_init (hpc3c0,SGI_ENET_IRQ ,0 ); +/* Let's see if second HPC is there */ +if (!(ip22_is_fullhouse ()) && +get_dbe (tmp, (unsigned int *)&hpc3c1->pbdma[1 ]) ==0 ) { + sgimc->giopar |=SGIMC_GIOPAR_MASTEREXP1 | +SGIMC_GIOPAR_EXP164 | +SGIMC_GIOPAR_HPC264 ; + hpc3c1->pbus_piocfg[0 ][0 ] =0x3ffff ; +/* interrupt/config register on Challenge S Mezz board */ + hpc3c1->pbus_extregs[0 ][0 ] =0x30 ; + ret2 =sgiseeq_init (hpc3c1,SGI_GIO_0_IRQ ,1 ); + } + +return (ret1 & ret2) ? ret1 :0 ; } static void __exit sgiseeq_exit(void)
Jeff Garzik
AppliedQuoted 9 lines · Ralf Baechle
From: Ladislav Michl <[email protected]>
Thanks to Jö Fahlke for donating hardware.
Signed-off-by Ladislav Michl <[email protected]>Forward porting of Ladis' 2.4 patch.
Signed-off-by Ralf Baechle <[email protected]>
applied to #upstream (2.6.22)