Skip to contentSkip to conversation

b44: high ping times with wireless-dev

DISCUSSION Maximilian Engelhardt 3 participants 8 messages Jun 16, 2007 – Jun 17, 2007

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

Hello,

I recently did some test and found out something interesting about the b44 problem I wrote earlier.

The problem is the following:
When I use my BCM4401 with the b44 driver in wireless-dev I get very high ping times looking like this:

64 bytes from 172.30.10.1: icmp_seq=1 ttl=64 time=1863 ms 64 bytes from 172.30.10.1: icmp_seq=2 ttl=64 time=855 ms 64 bytes from 172.30.10.1: icmp_seq=3 ttl=64 time=1855 ms 64 bytes from 172.30.10.1: icmp_seq=4 ttl=64 time=855 ms 64 bytes from 172.30.10.1: icmp_seq=5 ttl=64 time=1854 ms 64 bytes from 172.30.10.1: icmp_seq=6 ttl=64 time=854 ms 64 bytes from 172.30.10.1: icmp_seq=7 ttl=64 time=1851 ms 64 bytes from 172.30.10.1: icmp_seq=8 ttl=64 time=851 ms 64 bytes from 172.30.10.1: icmp_seq=9 ttl=64 time=1851 ms 64 bytes from 172.30.10.1: icmp_seq=10 ttl=64 time=851 ms

I also found out that shortly after I boot my laptop and log into kde ping times are not that high but start to increase very quickly:

64 bytes from 172.30.10.1: icmp_seq=53 ttl=64 time=2.19 ms 64 bytes from 172.30.10.1: icmp_seq=54 ttl=64 time=2.22 ms 64 bytes from 172.30.10.1: icmp_seq=55 ttl=64 time=2.20 ms 64 bytes from 172.30.10.1: icmp_seq=56 ttl=64 time=2.20 ms 64 bytes from 172.30.10.1: icmp_seq=57 ttl=64 time=18.6 ms 64 bytes from 172.30.10.1: icmp_seq=58 ttl=64 time=1268 ms 64 bytes from 172.30.10.1: icmp_seq=59 ttl=64 time=268 ms 64 bytes from 172.30.10.1: icmp_seq=60 ttl=64 time=1268 ms 64 bytes from 172.30.10.1: icmp_seq=61 ttl=64 time=268 ms 64 bytes from 172.30.10.1: icmp_seq=62 ttl=64 time=6.08 ms 64 bytes from 172.30.10.1: icmp_seq=63 ttl=64 time=268 ms 64 bytes from 172.30.10.1: icmp_seq=64 ttl=64 time=1264 ms 64 bytes from 172.30.10.1: icmp_seq=65 ttl=64 time=264 ms

After some time digging around I found out something really interesting. When I play some music ping times are immediately lower. If I stop playing music they are back to the same times as they were before.

I guess that there is a problem with interrupts so I post some information of my system in hope it will be usefull.

maxi@koala:~$ cat /proc/interrupts
          CPU0       
 0:     126317    XT-PIC-XT        timer
 1:       3600    XT-PIC-XT        i8042
 2:          0    XT-PIC-XT        cascade
 7:          1    XT-PIC-XT        parport0
 8:          1    XT-PIC-XT        rtc
 9:      17371    XT-PIC-XT        acpi
10:      13237    XT-PIC-XT        firewire_ohci, yenta, yenta, ehci_hcd:usb1, 
uhci_hcd:usb3, uhci_hcd:usb4, Intel 82801DB-ICH4, Intel 82801DB-ICH4 Modem, 
eth0
11:      89059    XT-PIC-XT        uhci_hcd:usb2, i915@pci:0000:00:02.0
12:        632    XT-PIC-XT        i8042
14:      10354    XT-PIC-XT        libata
15:       7408    XT-PIC-XT        libata
NMI:          0 
ERR:          0

[...]
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 10
ACPI: PCI Interrupt 0000:02:02.0[A] -> Link [LNKD] -> GSI 10 (level, low) -> IRQ 10
ssb: Sonics Silicon Backplane found on PCI device 0000:02:02.0 b44.c:v2.0
eth0: Broadcom 44xx/47xx 10/100BaseT Ethernet 00:c0:9f:29:99:a7 [...]

This problem did only happen with wireless-dev (checkout this evening) and with -mm kernels I used some time ago for testing. Currently I'm running 2.6.22-rc4 that works perfectly fine and doesn't show that problem.

Maxi

#1 lore raw
Quoted 72 lines · On Sat, 16 Jun 2007 23:27:43 +0200 Maximilian Engelhardt…

Hello,

I recently did some test and found out something interesting about the b44 problem I wrote earlier.

The problem is the following:
When I use my BCM4401 with the b44 driver in wireless-dev I get very high ping times looking like this:

64 bytes from 172.30.10.1: icmp_seq=1 ttl=64 time=1863 ms 64 bytes from 172.30.10.1: icmp_seq=2 ttl=64 time=855 ms 64 bytes from 172.30.10.1: icmp_seq=3 ttl=64 time=1855 ms 64 bytes from 172.30.10.1: icmp_seq=4 ttl=64 time=855 ms 64 bytes from 172.30.10.1: icmp_seq=5 ttl=64 time=1854 ms 64 bytes from 172.30.10.1: icmp_seq=6 ttl=64 time=854 ms 64 bytes from 172.30.10.1: icmp_seq=7 ttl=64 time=1851 ms 64 bytes from 172.30.10.1: icmp_seq=8 ttl=64 time=851 ms 64 bytes from 172.30.10.1: icmp_seq=9 ttl=64 time=1851 ms 64 bytes from 172.30.10.1: icmp_seq=10 ttl=64 time=851 ms

I also found out that shortly after I boot my laptop and log into kde ping times are not that high but start to increase very quickly:

64 bytes from 172.30.10.1: icmp_seq=53 ttl=64 time=2.19 ms 64 bytes from 172.30.10.1: icmp_seq=54 ttl=64 time=2.22 ms 64 bytes from 172.30.10.1: icmp_seq=55 ttl=64 time=2.20 ms 64 bytes from 172.30.10.1: icmp_seq=56 ttl=64 time=2.20 ms 64 bytes from 172.30.10.1: icmp_seq=57 ttl=64 time=18.6 ms 64 bytes from 172.30.10.1: icmp_seq=58 ttl=64 time=1268 ms 64 bytes from 172.30.10.1: icmp_seq=59 ttl=64 time=268 ms 64 bytes from 172.30.10.1: icmp_seq=60 ttl=64 time=1268 ms 64 bytes from 172.30.10.1: icmp_seq=61 ttl=64 time=268 ms 64 bytes from 172.30.10.1: icmp_seq=62 ttl=64 time=6.08 ms 64 bytes from 172.30.10.1: icmp_seq=63 ttl=64 time=268 ms 64 bytes from 172.30.10.1: icmp_seq=64 ttl=64 time=1264 ms 64 bytes from 172.30.10.1: icmp_seq=65 ttl=64 time=264 ms

After some time digging around I found out something really interesting. When I play some music ping times are immediately lower. If I stop playing music they are back to the same times as they were before.

I guess that there is a problem with interrupts so I post some information of my system in hope it will be usefull.

maxi@koala:~$ cat /proc/interrupts
          CPU0       
 0:     126317    XT-PIC-XT        timer
 1:       3600    XT-PIC-XT        i8042
 2:          0    XT-PIC-XT        cascade
 7:          1    XT-PIC-XT        parport0
 8:          1    XT-PIC-XT        rtc
 9:      17371    XT-PIC-XT        acpi
10:      13237    XT-PIC-XT        firewire_ohci, yenta, yenta, ehci_hcd:usb1, 
uhci_hcd:usb3, uhci_hcd:usb4, Intel 82801DB-ICH4, Intel 82801DB-ICH4 Modem, 
eth0
11:      89059    XT-PIC-XT        uhci_hcd:usb2, i915@pci:0000:00:02.0
12:        632    XT-PIC-XT        i8042
14:      10354    XT-PIC-XT        libata
15:       7408    XT-PIC-XT        libata
NMI:          0 
ERR:          0

[...]
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 10
ACPI: PCI Interrupt 0000:02:02.0[A] -> Link [LNKD] -> GSI 10 (level, low) -> IRQ 10
ssb: Sonics Silicon Backplane found on PCI device 0000:02:02.0 b44.c:v2.0
eth0: Broadcom 44xx/47xx 10/100BaseT Ethernet 00:c0:9f:29:99:a7 [...]

Quoted 5 lines

This problem did only happen with wireless-dev (checkout this evening) and with -mm kernels I used some time ago for testing. Currently I'm running 2.6.22-rc4 that works perfectly fine and doesn't show that problem.

Maxi

Can you build with APIC for uniprocessor.

There is lots of IRQ sharing, so
- one of the other device's may be not handling shared IRQ properly. Try unloading firewhire modem and yenta devices.

- IRQ might be set edge triggered which doesn't work with NAPI or shared IRQ.

Signature · 1 line
Stephen Hemminger <shemminger-de/[email protected]>
#2 lore raw
Quoted 75 lines · Stephen Hemminger

On Sat, 16 Jun 2007 23:27:43 +0200

Quoted 72 lines · Maximilian Engelhardt

Hello,

I recently did some test and found out something interesting about the b44 problem I wrote earlier.

The problem is the following:
When I use my BCM4401 with the b44 driver in wireless-dev I get very high ping times looking like this:

64 bytes from 172.30.10.1: icmp_seq=1 ttl=64 time=1863 ms 64 bytes from 172.30.10.1: icmp_seq=2 ttl=64 time=855 ms 64 bytes from 172.30.10.1: icmp_seq=3 ttl=64 time=1855 ms 64 bytes from 172.30.10.1: icmp_seq=4 ttl=64 time=855 ms 64 bytes from 172.30.10.1: icmp_seq=5 ttl=64 time=1854 ms 64 bytes from 172.30.10.1: icmp_seq=6 ttl=64 time=854 ms 64 bytes from 172.30.10.1: icmp_seq=7 ttl=64 time=1851 ms 64 bytes from 172.30.10.1: icmp_seq=8 ttl=64 time=851 ms 64 bytes from 172.30.10.1: icmp_seq=9 ttl=64 time=1851 ms 64 bytes from 172.30.10.1: icmp_seq=10 ttl=64 time=851 ms

I also found out that shortly after I boot my laptop and log into kde ping times are not that high but start to increase very quickly:

64 bytes from 172.30.10.1: icmp_seq=53 ttl=64 time=2.19 ms 64 bytes from 172.30.10.1: icmp_seq=54 ttl=64 time=2.22 ms 64 bytes from 172.30.10.1: icmp_seq=55 ttl=64 time=2.20 ms 64 bytes from 172.30.10.1: icmp_seq=56 ttl=64 time=2.20 ms 64 bytes from 172.30.10.1: icmp_seq=57 ttl=64 time=18.6 ms 64 bytes from 172.30.10.1: icmp_seq=58 ttl=64 time=1268 ms 64 bytes from 172.30.10.1: icmp_seq=59 ttl=64 time=268 ms 64 bytes from 172.30.10.1: icmp_seq=60 ttl=64 time=1268 ms 64 bytes from 172.30.10.1: icmp_seq=61 ttl=64 time=268 ms 64 bytes from 172.30.10.1: icmp_seq=62 ttl=64 time=6.08 ms 64 bytes from 172.30.10.1: icmp_seq=63 ttl=64 time=268 ms 64 bytes from 172.30.10.1: icmp_seq=64 ttl=64 time=1264 ms 64 bytes from 172.30.10.1: icmp_seq=65 ttl=64 time=264 ms

After some time digging around I found out something really interesting. When I play some music ping times are immediately lower. If I stop playing music they are back to the same times as they were before.

I guess that there is a problem with interrupts so I post some information of my system in hope it will be usefull.

maxi@koala:~$ cat /proc/interrupts
          CPU0
 0:     126317    XT-PIC-XT        timer
 1:       3600    XT-PIC-XT        i8042
 2:          0    XT-PIC-XT        cascade
 7:          1    XT-PIC-XT        parport0
 8:          1    XT-PIC-XT        rtc
 9:      17371    XT-PIC-XT        acpi
10:      13237    XT-PIC-XT        firewire_ohci, yenta, yenta,
ehci_hcd:usb1, uhci_hcd:usb3, uhci_hcd:usb4, Intel 82801DB-ICH4, Intel
82801DB-ICH4 Modem, eth0
11:      89059    XT-PIC-XT        uhci_hcd:usb2, i915@pci:0000:00:02.0
12:        632    XT-PIC-XT        i8042
14:      10354    XT-PIC-XT        libata
15:       7408    XT-PIC-XT        libata
NMI:          0
ERR:          0

[...]
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 10
ACPI: PCI Interrupt 0000:02:02.0[A] -> Link [LNKD] -> GSI 10 (level, low) -> IRQ 10
ssb: Sonics Silicon Backplane found on PCI device 0000:02:02.0 b44.c:v2.0
eth0: Broadcom 44xx/47xx 10/100BaseT Ethernet 00:c0:9f:29:99:a7 [...]

Quoted 8 lines
Quoted 6 lines

This problem did only happen with wireless-dev (checkout this evening) and with -mm kernels I used some time ago for testing. Currently I'm running 2.6.22-rc4 that works perfectly fine and doesn't show that problem.

Maxi

Can you build with APIC for uniprocessor.

I did enable CONFIG_X86_UP_APIC and CONFIG_X86_UP_IOAPIC and tried with lapic and apic=force but couldn't get APIC working.

Quoted 7 lines

There is lots of IRQ sharing, so
- one of the other device's may be not handling shared IRQ properly. Try unloading firewhire modem and yenta devices.

- IRQ might be set edge triggered which doesn't work with NAPI or shared IRQ.

I did build a kernel without the three mentioned above but the problem is still the same. I also did remove everything but eth0 on interrupt 10 so the only device using that interrupt is eth0 and then the card completely stopped working.

Maxi

#3 lore raw
Quoted 4 lines · On Sunday 17 June 2007 02:42:18 Maximilian Engelhardt wrote:

I did build a kernel without the three mentioned above but the problem is still the same. I also did remove everything but eth0 on interrupt 10 so the only device using that interrupt is eth0 and then the card completely stopped working.

_That_ is interesting...
Maybe the IRQ isn't correctly wired up on the backplane and it doesn't generate IRQs at all (so it only worked, because other devices on the same IRQ line triggered the line).
I'll take a look at that code.

Signature · 1 line
Greetings Michael.
#4 lore raw
In reply to Maximilian Engelhardt
Quoted 8 lines · On Saturday 16 June 2007 23:27:43 Maximilian Engelhardt wrote:

[...]
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 10
ACPI: PCI Interrupt 0000:02:02.0[A] -> Link [LNKD] -> GSI 10 (level, low) -> IRQ 10
ssb: Sonics Silicon Backplane found on PCI device 0000:02:02.0 b44.c:v2.0
eth0: Broadcom 44xx/47xx 10/100BaseT Ethernet 00:c0:9f:29:99:a7 [...]

Ok, I prepared two debugging patches.

Please enable SonicsSiliconBackplane Debugging in the kernel kconfig, so I can get more detail information about your card. Device Drivers/Sonics Silicon Backplane/SSB debugging (Must disable "No SSB kernel messages")

Please apply and test the attached debugging patches in a row. So apply patch 1 and test if it works again. If not, apply patch 2 and test if it works.
Always save complete dmesg log on each test run and send it to me.

Thanks for testing.
(This time it seems we are actually getting somewhere, when dealing with sane people. :D )

Signature · 1 line
Greetings Michael.
drivers/ssb/driver_pcicore.c +4 -1
Index: bu3sch-wireless-dev/drivers/ssb/driver_pcicore.c
===================================================================
@@ -477,6 +477,7 @@ int ssb_pcicore_dev_irqvecs_enable(struc
 		goto out;
 	bus = pdev->bus;
 
+printk("Enabling IRQ vectors\n");
 	/* Enable interrupts for this device. */
 	if (bus->host_pci &&
 	    ((pdev->id.revision >= 6) || (pdev->id.coreid == SSB_DEV_PCIE))) {
@@ -497,8 +498,10 @@ int ssb_pcicore_dev_irqvecs_enable(struc
 
 		intvec = ssb_read32(pdev, SSB_INTVEC);
 		tmp = ssb_read32(dev, SSB_TPSFLAG);
+printk("Writing INTVEC. TPSFLAG is 0x%08X\n", tmp);
 		tmp &= SSB_TPSFLAG_BPFLAG;
-		intvec |= tmp;
+//		intvec |= tmp;
+intvec |= 0x00000002;
 		ssb_write32(pdev, SSB_INTVEC, intvec);
 	}
 
drivers/ssb/driver_pcicore.c +3 -0
Index: bu3sch-wireless-dev/drivers/ssb/driver_pcicore.c
===================================================================
@@ -514,6 +514,8 @@ intvec |= 0x00000002;
 		tmp |= SSB_PCICORE_SBTOPCI_BURST;
 		pcicore_write32(pc, SSB_PCICORE_SBTOPCI2, tmp);
 
+printk("Wrote translation\n");
+#if 0
 		if (pdev->id.revision < 5) {
 			tmp = ssb_read32(pdev, SSB_IMCFGLO);
 			tmp &= ~SSB_IMCFGLO_SERTO;
@@ -527,6 +529,7 @@ intvec |= 0x00000002;
 			tmp |= SSB_PCICORE_SBTOPCI_MRM;
 			pcicore_write32(pc, SSB_PCICORE_SBTOPCI2, tmp);
 		}
+#endif
 	} else {
 		assert(pdev->id.coreid == SSB_DEV_PCIE);
 		//TODO: Better make defines for all these magic PCIE values.
#5 lore raw
Quoted 17 lines · On Sunday 17 June 2007 12:55:39 Michael Buesch wrote:
Quoted 8 lines · On Saturday 16 June 2007 23:27:43 Maximilian Engelhardt wrote:

[...]
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 10
ACPI: PCI Interrupt 0000:02:02.0[A] -> Link [LNKD] -> GSI 10 (level, low) -> IRQ 10
ssb: Sonics Silicon Backplane found on PCI device 0000:02:02.0 b44.c:v2.0
eth0: Broadcom 44xx/47xx 10/100BaseT Ethernet 00:c0:9f:29:99:a7 [...]

Ok, I prepared two debugging patches.

Please enable SonicsSiliconBackplane Debugging in the kernel kconfig, so I can get more detail information about your card. Device Drivers/Sonics Silicon Backplane/SSB debugging (Must disable "No SSB kernel messages")

Quoted 9 lines

Please apply and test the attached debugging patches in a row. So apply patch 1 and test if it works again. If not, apply patch 2 and test if it works.
Always save complete dmesg log on each test run and send it to me.

Thanks for testing.
(This time it seems we are actually getting somewhere, when dealing with sane people. :D )

Ah, forgot to say. Apply patch 2 on top of patch 1.

Signature · 1 line
Greetings Michael.
#6 lore raw
In reply to Michael Buesch
Quoted 17 lines · Michael Buesch
Quoted 8 lines · On Saturday 16 June 2007 23:27:43 Maximilian Engelhardt wrote:

[...]
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 10
ACPI: PCI Interrupt 0000:02:02.0[A] -> Link [LNKD] -> GSI 10 (level, low) -> IRQ 10
ssb: Sonics Silicon Backplane found on PCI device 0000:02:02.0 b44.c:v2.0
eth0: Broadcom 44xx/47xx 10/100BaseT Ethernet 00:c0:9f:29:99:a7 [...]

Ok, I prepared two debugging patches.

Please enable SonicsSiliconBackplane Debugging in the kernel kconfig, so I can get more detail information about your card. Device Drivers/Sonics Silicon Backplane/SSB debugging (Must disable "No SSB kernel messages")

Quoted 8 lines

Please apply and test the attached debugging patches in a row. So apply patch 1 and test if it works again. If not, apply patch 2 and test if it works.
Always save complete dmesg log on each test run and send it to me.

Thanks for testing.
(This time it seems we are actually getting somewhere, when dealing with sane people. :D )

I did the tests with my kernel where only the card is on interrupt 10. dmesg is attached.
With the first patch applied networking does work again. I also additionally tried patch2 and it also does work.

Maxi

Linux version 2.6.22-rc4-wireless-dev-20070616-test1 (root@koala) (gcc version 4.1.3 20070601 (prerelease) (Debian 4.1.2-12)) #6 PREEMPT Sun Jun 17 13:24:13 CEST 2007 BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000ce000 - 00000000000d0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000004dee0000 (usable)
BIOS-e820: 000000004dee0000 - 000000004deec000 (ACPI data)
BIOS-e820: 000000004deec000 - 000000004df00000 (ACPI NVS)
BIOS-e820: 000000004df00000 - 0000000050000000 (reserved)
BIOS-e820: 00000000fec10000 - 00000000fec20000 (reserved)
BIOS-e820: 00000000ff800000 - 00000000ffc00000 (reserved)
BIOS-e820: 00000000fffffc00 - 0000000100000000 (reserved)
350MB HIGHMEM available.
896MB LOWMEM available.
Entering add_active_range(0, 0, 319200) 0 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 229376
HighMem 229376 -> 319200
early_node_map[1] active PFN ranges

    0:        0 ->   319200

On node 0 totalpages: 319200
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 1760 pages used for memmap
Normal zone: 223520 pages, LIFO batch:31
HighMem zone: 701 pages used for memmap
HighMem zone: 89123 pages, LIFO batch:15
DMI present.
ACPI: RSDP 000F6050, 0014 (r0 ACER )
ACPI: RSDT 4DEE5A39, 0030 (r1 ACER Wagtail 20020114 LTP 0)
ACPI: FACP 4DEEBF2C, 0074 (r1 ACER Wagtail 20020114 PTL 50)
ACPI: DSDT 4DEE5A69, 64C3 (r1 ACER Wagtail 20020114 MSFT 100000E)
ACPI: FACS 4DEFCFC0, 0040
ACPI: HPET 4DEEBFA0, 0038 (r1 ACER Wagtail 20020114 PTL 0)
ACPI: BOOT 4DEEBFD8, 0028 (r1 ACER Wagtail 20020114 LTP 1)
ACPI: PM-Timer IO Port: 0x1008
ACPI: HPET id: 0x8086a201 base: 0x0
Allocating PCI resources starting at 60000000 (gap: 50000000:aec10000)
Built 1 zonelists. Total pages: 316707
Kernel command line: root=/dev/sda1 ro vga=0x31b resume=/dev/sda2
Local APIC disabled by BIOS -- you can enable it with "lapic"
mapped APIC to ffffd000 (019c4000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Detected 1395.565 MHz processor.
Console: colour dummy device 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1259844k/1276800k available (3572k kernel code, 16168k reserved, 1152k data, 220k init, 359296k highmem) virtual kernel memory layout:

    fixmap  : 0xfffaa000 - 0xfffff000   ( 340 kB)
    pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
    vmalloc : 0xf8800000 - 0xff7fe000   ( 111 MB)
    lowmem  : 0xc0000000 - 0xf8000000   ( 896 MB)
      .init : 0xc05a0000 - 0xc05d7000   ( 220 kB)
      .data : 0xc047d05d - 0xc059d0b0   (1152 kB)
      .text : 0xc0100000 - 0xc047d05d   (3572 kB)

Checking if this processor honours the WP bit even in supervisor mode... Ok.
SLUB: Genslabs=23, HWalign=64, Order=0-1, MinObjects=4, Processors=1, Nodes=1
Calibrating delay using timer specific routine.. 2793.34 BogoMIPS (lpj=4653358)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: a7e9f9bf 00000000 00000000 00000000 00000180 00000000 00000000
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 1024K
CPU: After all inits, caps: a7e9f9bf 00000000 00000000 00002040 00000180 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
CPU: Intel(R) Pentium(R) M processor 1400MHz stepping 05
Checking 'hlt' instruction... OK.
ACPI: Core revision 20070126
ACPI: setting ELCR to 0200 (from 0c00)
NET: Registered protocol family 16
No dock devices found.
ACPI: \_SB_.PCI0.IDE0.SECN.BAY1: found ejectable bay
ACPI: \_SB_.PCI0.IDE0.SECN.BAY1: Adding notify handler
ACPI: Bay [\_SB_.PCI0.IDE0.SECN.BAY1] Added
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfd742, last bus=2
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S4 S5)
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI quirk: region 1000-107f claimed by ICH4 ACPI/GPIO/TCO
PCI quirk: region 1180-11bf claimed by ICH4 GPIO
PCI: Transparent bridge - 0000:00:1e.0
PCI: Bus #03 (-#06) is hidden behind transparent bridge #02 (-#02) (try 'pci=assign-busses')
Please report the result to linux-kernel to fix this permanently
PCI: Bus #07 (-#0a) is hidden behind transparent bridge #02 (-#02) (try 'pci=assign-busses')
Please report the result to linux-kernel to fix this permanently
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs *11)
ACPI: PCI Interrupt Link [LNKB] (IRQs *10)
ACPI: PCI Interrupt Link [LNKC] (IRQs *10)
ACPI: PCI Interrupt Link [LNKD] (IRQs 10) *11
ACPI: PCI Interrupt Link [LNKE] (IRQs 10) *11
ACPI: PCI Interrupt Link [LNKF] (IRQs 10) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs *10)
ACPI: Power Resource [PFN0] (off)
ACPI: Power Resource [PFN1] (off)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 11 devices
ACPI: ACPI bus type pnp unregistered
SCSI subsystem initialized
libata version 2.21 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
pnp: 00:04: iomem range 0xfec10000-0xfec1ffff could not be reserved
pnp: 00:04: iomem range 0xff800000-0xffbfffff could not be reserved
pnp: 00:04: iomem range 0xfff00000-0xffffffff could not be reserved
pnp: 00:04: iomem range 0x0-0x9ffff could not be reserved
Time: tsc clocksource has been installed.
PCI: Bus 3, cardbus bridge: 0000:02:06.0
IO window: 00003000-000030ff
IO window: 00003400-000034ff
PREFETCH window: 60000000-63ffffff
MEM window: 6c000000-6fffffff
PCI: Bus 7, cardbus bridge: 0000:02:06.1
IO window: 00003800-000038ff
IO window: 00003c00-00003cff
PREFETCH window: 64000000-67ffffff
MEM window: 70000000-73ffffff
PCI: Bridge: 0000:00:1e.0
IO window: 3000-3fff
MEM window: e0200000-e07fffff
PREFETCH window: 60000000-67ffffff
PCI: Setting latency timer of device 0000:00:1e.0 to 64
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:02:06.0[A] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI Interrupt 0000:02:06.1[A] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
Simple Boot Flag at 0x37 set to 0x1
Machine check exception polling timer started.
highmem bounce pool size: 64 pages
NTFS driver 2.1.28 [Flags: R/W].
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Boot video device is 0000:00:02.0
ACPI: AC Adapter [ACAD] (on-line)
ACPI: Battery Slot [BAT1] (battery present)
ACPI: Battery Slot [BAT2] (battery absent)
input: Power Button (FF) as /class/input/input0
ACPI: Power Button (FF) [PWRF]
input: Lid Switch as /class/input/input1
ACPI: Lid Switch [LID]
input: Sleep Button (CM) as /class/input/input2
ACPI: Sleep Button (CM) [SLPB]
ACPI: Transitioning device [FAN0] to D3
ACPI: Transitioning device [FAN0] to D3
ACPI: Fan [FAN0] (off)
ACPI: Transitioning device [FAN1] to D3
ACPI: Transitioning device [FAN1] to D3
ACPI: Fan [FAN1] (off)
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Thermal Zone [THRM] (54 C)
lp: driver loaded but no devices found
Real Time Clock Driver v1.12ac
intel_rng: FWH not detected
ppdev: user-space parallel port driver
Linux agpgart interface v0.102 (c) Dave Jones
agpgart: Detected an Intel 855 Chipset.
agpgart: Detected 32636K stolen memory.
agpgart: AGP aperture is 128M @ 0xe8000000
[drm] Initialized drm 1.1.0 20060810
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
[drm] Initialized i915 1.6.0 20060119 on minor 0
[drm] Initialized i915 1.6.0 20060119 on minor 1
intelfb: Framebuffer driver for Intel(R) 830M/845G/852GM/855GM/865G/915G/915GM/945G/945GM chipsets
intelfb: Version 0.9.4
intelfb: 00:02.0: Intel(R) 855GM, aperture size 128MB, stolen memory 32636kB
intelfb: Non-CRT device is enabled ( LVDS port ). Disabling mode switching.
intelfb: Initial video mode is 1280x1024-32@60.
intelfb: Changing the video mode is not supported.
Console: switching to colour frame buffer device 160x64
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
ACPI: PCI Interrupt 0000:00:1f.6[B] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI interrupt for device 0000:00:1f.6 disabled
parport_pc 00:08: reported by Plug and Play ACPI
parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
Marking TSC unstable due to: possible TSC halt in C2.
Time: acpi_pm clocksource has been installed.
Switched to high resolution mode on CPU 0
lp0: using parport0 (interrupt-driven).
loop: module loaded
nbd: registered device at major 43
Ethernet Channel Bonding Driver: v3.1.2 (January 20, 2007)
bonding: Warning: either miimon or arp_interval and arp_ip_target module parameters must be specified, otherwise bonding will not detect link failures! see bonding.txt for details.
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 10
ACPI: PCI Interrupt 0000:02:02.0[A] -> Link [LNKD] -> GSI 10 (level, low) -> IRQ 10
ssb: Core 0 found: Fast Ethernet (cc 0x806, rev 0x04, vendor 0x4243)
ssb: Core 1 found: V90 (cc 0x807, rev 0x01, vendor 0x4243)
ssb: Core 2 found: PCI (cc 0x804, rev 0x02, vendor 0x4243)
ssb: Switching to PCI core, index 2
ssb: Sonics Silicon Backplane found on PCI device 0000:02:02.0
b44.c:v2.0
ssb: Switching to Fast Ethernet core, index 0
Enabling IRQ vectors
ssb: Switching to PCI core, index 2
ssb: Switching to Fast Ethernet core, index 0
Writing INTVEC. TPSFLAG is 0x00000041
ssb: Switching to PCI core, index 2
ssb: Switching to Fast Ethernet core, index 0
eth0: Broadcom 44xx/47xx 10/100BaseT Ethernet 00:c0:9f:29:99:a7
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk-zC7DfRvBq/JWk0Htik3J/[email protected]>
ata_piix 0000:00:1f.1: version 2.11
PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10
PCI: Setting latency timer of device 0000:00:1f.1 to 64
scsi0 : ata_piix
scsi1 : ata_piix
ata1: PATA max UDMA/100 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x00011810 irq 14
ata2: PATA max UDMA/100 cmd 0x00010170 ctl 0x00010376 bmdma 0x00011818 irq 15
ata1.00: ata_hpa_resize 1: sectors = 156301488, hpa_sectors = 156301488
ata1.00: ATA-6: TOSHIBA MK8026GAX, PA001G, max UDMA/100
ata1.00: 156301488 sectors, multi 16: LBA
ata1.00: ata_hpa_resize 1: sectors = 156301488, hpa_sectors = 156301488
ata1.00: configured for UDMA/100
ata2.00: ATAPI, max UDMA/33
ata2.00: configured for UDMA/33
scsi 0:0:0:0: Direct-Access ATA TOSHIBA MK8026GA PA00 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda:<4>Clocksource tsc unstable (delta = -413804920 ns)
sda1 sda2
sd 0:0:0:0: [sda] Attached SCSI disk
sd 0:0:0:0: Attached scsi generic sg0 type 0
scsi 1:0:0:0: CD-ROM Optiarc DVD RW AD-7543A 1-00 PQ: 0 ANSI: 5
sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 1:0:0:0: Attached scsi CD-ROM sr0
sr 1:0:0:0: Attached scsi generic sg1 type 5
usbmon: debugfs is not available
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:MOU2] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input3
input: PC Speaker as /class/input/input4
Synaptics Touchpad, model: 1, fw: 5.8, id: 0x9d48b1, caps: 0x904713/0x4006
input: SynPS/2 Synaptics TouchPad as /class/input/input5
i2c /dev entries driver
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
Advanced Linux Sound Architecture Driver Version 1.0.14 (Thu May 31 09:03:25 2007 UTC).
ALSA device list:
No soundcards found.
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (8192 buckets, 65536 max)
ctnetlink v0.93: registering with nfnetlink.
IPv4 over IPv4 tunneling driver
GRE over IPv4 tunneling driver
ip_tables: (C) 2000-2006 Netfilter Core Team
ClusterIP Version 0.8 loaded successfully
arp_tables: (C) 2002 David S. Miller
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
Mobile IPv6
ip6_tables: (C) 2000-2006 Netfilter Core Team
IPv6 over IPv4 tunneling driver
sit0: Disabled Privacy Extensions
NET: Registered protocol family 17
NET: Registered protocol family 15
Using IPI Shortcut mode
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 220k freed
ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 10
ACPI: PCI Interrupt 0000:02:04.0[A] -> Link [LNKE] -> GSI 10 (level, low) -> IRQ 10
p54: LM86 firmware
wmaster0: Selected rate control algorithm 'simple'
phy0: hwaddr 00:60:b3:91:45:5b, isl3890
Adding 2001880k swap on /dev/sda2. Priority:-1 extents:1 across:2001880k
EXT3 FS on sda1, internal journal
fuse init (API version 7.8)
ADDRCONF(NETDEV_UP): eth0: link is not ready
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready

Linux version 2.6.22-rc4-wireless-dev-20070616-test1 (root@koala) (gcc version 4.1.3 20070601 (prerelease) (Debian 4.1.2-12)) #7 PREEMPT Sun Jun 17 13:47:38 CEST 2007 BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000ce000 - 00000000000d0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000004dee0000 (usable)
BIOS-e820: 000000004dee0000 - 000000004deec000 (ACPI data)
BIOS-e820: 000000004deec000 - 000000004df00000 (ACPI NVS)
BIOS-e820: 000000004df00000 - 0000000050000000 (reserved)
BIOS-e820: 00000000fec10000 - 00000000fec20000 (reserved)
BIOS-e820: 00000000ff800000 - 00000000ffc00000 (reserved)
BIOS-e820: 00000000fffffc00 - 0000000100000000 (reserved)
350MB HIGHMEM available.
896MB LOWMEM available.
Entering add_active_range(0, 0, 319200) 0 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 229376
HighMem 229376 -> 319200
early_node_map[1] active PFN ranges

    0:        0 ->   319200

On node 0 totalpages: 319200
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 1760 pages used for memmap
Normal zone: 223520 pages, LIFO batch:31
HighMem zone: 701 pages used for memmap
HighMem zone: 89123 pages, LIFO batch:15
DMI present.
ACPI: RSDP 000F6050, 0014 (r0 ACER )
ACPI: RSDT 4DEE5A39, 0030 (r1 ACER Wagtail 20020114 LTP 0)
ACPI: FACP 4DEEBF2C, 0074 (r1 ACER Wagtail 20020114 PTL 50)
ACPI: DSDT 4DEE5A69, 64C3 (r1 ACER Wagtail 20020114 MSFT 100000E)
ACPI: FACS 4DEFCFC0, 0040
ACPI: HPET 4DEEBFA0, 0038 (r1 ACER Wagtail 20020114 PTL 0)
ACPI: BOOT 4DEEBFD8, 0028 (r1 ACER Wagtail 20020114 LTP 1)
ACPI: PM-Timer IO Port: 0x1008
ACPI: HPET id: 0x8086a201 base: 0x0
Allocating PCI resources starting at 60000000 (gap: 50000000:aec10000)
Built 1 zonelists. Total pages: 316707
Kernel command line: root=/dev/sda1 ro vga=0x31b resume=/dev/sda2
Local APIC disabled by BIOS -- you can enable it with "lapic"
mapped APIC to ffffd000 (019c4000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Detected 1395.554 MHz processor.
Console: colour dummy device 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1259844k/1276800k available (3571k kernel code, 16168k reserved, 1148k data, 220k init, 359296k highmem) virtual kernel memory layout:

    fixmap  : 0xfffaa000 - 0xfffff000   ( 340 kB)
    pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
    vmalloc : 0xf8800000 - 0xff7fe000   ( 111 MB)
    lowmem  : 0xc0000000 - 0xf8000000   ( 896 MB)
      .init : 0xc05a0000 - 0xc05d7000   ( 220 kB)
      .data : 0xc047cf7d - 0xc059c0b0   (1148 kB)
      .text : 0xc0100000 - 0xc047cf7d   (3571 kB)

Checking if this processor honours the WP bit even in supervisor mode... Ok.
SLUB: Genslabs=23, HWalign=64, Order=0-1, MinObjects=4, Processors=1, Nodes=1
Calibrating delay using timer specific routine.. 2793.33 BogoMIPS (lpj=4653334)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: a7e9f9bf 00000000 00000000 00000000 00000180 00000000 00000000
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 1024K
CPU: After all inits, caps: a7e9f9bf 00000000 00000000 00002040 00000180 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
CPU: Intel(R) Pentium(R) M processor 1400MHz stepping 05
Checking 'hlt' instruction... OK.
ACPI: Core revision 20070126
ACPI: setting ELCR to 0200 (from 0c00)
NET: Registered protocol family 16
No dock devices found.
ACPI: \_SB_.PCI0.IDE0.SECN.BAY1: found ejectable bay
ACPI: \_SB_.PCI0.IDE0.SECN.BAY1: Adding notify handler
ACPI: Bay [\_SB_.PCI0.IDE0.SECN.BAY1] Added
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfd742, last bus=2
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S4 S5)
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI quirk: region 1000-107f claimed by ICH4 ACPI/GPIO/TCO
PCI quirk: region 1180-11bf claimed by ICH4 GPIO
PCI: Transparent bridge - 0000:00:1e.0
PCI: Bus #03 (-#06) is hidden behind transparent bridge #02 (-#02) (try 'pci=assign-busses')
Please report the result to linux-kernel to fix this permanently
PCI: Bus #07 (-#0a) is hidden behind transparent bridge #02 (-#02) (try 'pci=assign-busses')
Please report the result to linux-kernel to fix this permanently
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs *11)
ACPI: PCI Interrupt Link [LNKB] (IRQs *10)
ACPI: PCI Interrupt Link [LNKC] (IRQs *10)
ACPI: PCI Interrupt Link [LNKD] (IRQs 10) *11
ACPI: PCI Interrupt Link [LNKE] (IRQs 10) *11
ACPI: PCI Interrupt Link [LNKF] (IRQs 10) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs *10)
ACPI: Power Resource [PFN0] (off)
ACPI: Power Resource [PFN1] (off)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 11 devices
ACPI: ACPI bus type pnp unregistered
SCSI subsystem initialized
libata version 2.21 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
pnp: 00:04: iomem range 0xfec10000-0xfec1ffff could not be reserved
pnp: 00:04: iomem range 0xff800000-0xffbfffff could not be reserved
pnp: 00:04: iomem range 0xfff00000-0xffffffff could not be reserved
pnp: 00:04: iomem range 0x0-0x9ffff could not be reserved
Time: tsc clocksource has been installed.
PCI: Bus 3, cardbus bridge: 0000:02:06.0
IO window: 00003000-000030ff
IO window: 00003400-000034ff
PREFETCH window: 60000000-63ffffff
MEM window: 6c000000-6fffffff
PCI: Bus 7, cardbus bridge: 0000:02:06.1
IO window: 00003800-000038ff
IO window: 00003c00-00003cff
PREFETCH window: 64000000-67ffffff
MEM window: 70000000-73ffffff
PCI: Bridge: 0000:00:1e.0
IO window: 3000-3fff
MEM window: e0200000-e07fffff
PREFETCH window: 60000000-67ffffff
PCI: Setting latency timer of device 0000:00:1e.0 to 64
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:02:06.0[A] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI Interrupt 0000:02:06.1[A] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
Simple Boot Flag at 0x37 set to 0x1
Machine check exception polling timer started.
highmem bounce pool size: 64 pages
NTFS driver 2.1.28 [Flags: R/W].
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Boot video device is 0000:00:02.0
ACPI: AC Adapter [ACAD] (on-line)
ACPI: Battery Slot [BAT1] (battery present)
ACPI: Battery Slot [BAT2] (battery absent)
input: Power Button (FF) as /class/input/input0
ACPI: Power Button (FF) [PWRF]
input: Lid Switch as /class/input/input1
ACPI: Lid Switch [LID]
input: Sleep Button (CM) as /class/input/input2
ACPI: Sleep Button (CM) [SLPB]
ACPI: Transitioning device [FAN0] to D3
ACPI: Transitioning device [FAN0] to D3
ACPI: Fan [FAN0] (off)
ACPI: Transitioning device [FAN1] to D3
ACPI: Transitioning device [FAN1] to D3
ACPI: Fan [FAN1] (off)
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Thermal Zone [THRM] (49 C)
lp: driver loaded but no devices found
Real Time Clock Driver v1.12ac
intel_rng: FWH not detected
ppdev: user-space parallel port driver
Linux agpgart interface v0.102 (c) Dave Jones
agpgart: Detected an Intel 855 Chipset.
agpgart: Detected 32636K stolen memory.
agpgart: AGP aperture is 128M @ 0xe8000000
[drm] Initialized drm 1.1.0 20060810
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
[drm] Initialized i915 1.6.0 20060119 on minor 0
[drm] Initialized i915 1.6.0 20060119 on minor 1
intelfb: Framebuffer driver for Intel(R) 830M/845G/852GM/855GM/865G/915G/915GM/945G/945GM chipsets
intelfb: Version 0.9.4
intelfb: 00:02.0: Intel(R) 855GM, aperture size 128MB, stolen memory 32636kB
intelfb: Non-CRT device is enabled ( LVDS port ). Disabling mode switching.
intelfb: Initial video mode is 1280x1024-32@60.
intelfb: Changing the video mode is not supported.
Console: switching to colour frame buffer device 160x64
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
ACPI: PCI Interrupt 0000:00:1f.6[B] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI interrupt for device 0000:00:1f.6 disabled
parport_pc 00:08: reported by Plug and Play ACPI
parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
Marking TSC unstable due to: possible TSC halt in C2.
Time: acpi_pm clocksource has been installed.
Switched to high resolution mode on CPU 0
lp0: using parport0 (interrupt-driven).
loop: module loaded
nbd: registered device at major 43
Ethernet Channel Bonding Driver: v3.1.2 (January 20, 2007)
bonding: Warning: either miimon or arp_interval and arp_ip_target module parameters must be specified, otherwise bonding will not detect link failures! see bonding.txt for details.
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 10
ACPI: PCI Interrupt 0000:02:02.0[A] -> Link [LNKD] -> GSI 10 (level, low) -> IRQ 10
ssb: Core 0 found: Fast Ethernet (cc 0x806, rev 0x04, vendor 0x4243)
ssb: Core 1 found: V90 (cc 0x807, rev 0x01, vendor 0x4243)
ssb: Core 2 found: PCI (cc 0x804, rev 0x02, vendor 0x4243)
ssb: Switching to PCI core, index 2
ssb: Sonics Silicon Backplane found on PCI device 0000:02:02.0
b44.c:v2.0
ssb: Switching to Fast Ethernet core, index 0
Enabling IRQ vectors
ssb: Switching to PCI core, index 2
ssb: Switching to Fast Ethernet core, index 0
Writing INTVEC. TPSFLAG is 0x00000041
ssb: Switching to PCI core, index 2
Wrote translation
ssb: Switching to Fast Ethernet core, index 0
eth0: Broadcom 44xx/47xx 10/100BaseT Ethernet 00:c0:9f:29:99:a7
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk-zC7DfRvBq/JWk0Htik3J/[email protected]>
ata_piix 0000:00:1f.1: version 2.11
PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10
PCI: Setting latency timer of device 0000:00:1f.1 to 64
scsi0 : ata_piix
scsi1 : ata_piix
ata1: PATA max UDMA/100 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x00011810 irq 14
ata2: PATA max UDMA/100 cmd 0x00010170 ctl 0x00010376 bmdma 0x00011818 irq 15
ata1.00: ata_hpa_resize 1: sectors = 156301488, hpa_sectors = 156301488
ata1.00: ATA-6: TOSHIBA MK8026GAX, PA001G, max UDMA/100
ata1.00: 156301488 sectors, multi 16: LBA
ata1.00: ata_hpa_resize 1: sectors = 156301488, hpa_sectors = 156301488
ata1.00: configured for UDMA/100
ata2.00: ATAPI, max UDMA/33
ata2.00: configured for UDMA/33
scsi 0:0:0:0: Direct-Access ATA TOSHIBA MK8026GA PA00 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda:<4>Clocksource tsc unstable (delta = -417033865 ns)
sda1 sda2
sd 0:0:0:0: [sda] Attached SCSI disk
sd 0:0:0:0: Attached scsi generic sg0 type 0
scsi 1:0:0:0: CD-ROM Optiarc DVD RW AD-7543A 1-00 PQ: 0 ANSI: 5
sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 1:0:0:0: Attached scsi CD-ROM sr0
sr 1:0:0:0: Attached scsi generic sg1 type 5
usbmon: debugfs is not available
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:MOU2] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input3
input: PC Speaker as /class/input/input4
Synaptics Touchpad, model: 1, fw: 5.8, id: 0x9d48b1, caps: 0x904713/0x4006
input: SynPS/2 Synaptics TouchPad as /class/input/input5
i2c /dev entries driver
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
Advanced Linux Sound Architecture Driver Version 1.0.14 (Thu May 31 09:03:25 2007 UTC).
ALSA device list:
No soundcards found.
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (8192 buckets, 65536 max)
ctnetlink v0.93: registering with nfnetlink.
IPv4 over IPv4 tunneling driver
GRE over IPv4 tunneling driver
ip_tables: (C) 2000-2006 Netfilter Core Team
ClusterIP Version 0.8 loaded successfully
arp_tables: (C) 2002 David S. Miller
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
Mobile IPv6
ip6_tables: (C) 2000-2006 Netfilter Core Team
IPv6 over IPv4 tunneling driver
sit0: Disabled Privacy Extensions
NET: Registered protocol family 17
NET: Registered protocol family 15
Using IPI Shortcut mode
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 220k freed
ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 10
ACPI: PCI Interrupt 0000:02:04.0[A] -> Link [LNKE] -> GSI 10 (level, low) -> IRQ 10
p54: LM86 firmware
wmaster0: Selected rate control algorithm 'simple'
phy0: hwaddr 00:60:b3:91:45:5b, isl3890
Adding 2001880k swap on /dev/sda2. Priority:-1 extents:1 across:2001880k
EXT3 FS on sda1, internal journal
fuse init (API version 7.8)
ADDRCONF(NETDEV_UP): eth0: link is not ready
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready

#7 lore raw
Quoted 23 lines · On Sunday 17 June 2007 14:03:30 Maximilian Engelhardt wrote:
Quoted 22 lines · Michael Buesch
Quoted 8 lines · On Saturday 16 June 2007 23:27:43 Maximilian Engelhardt wrote:

[...]
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 10
ACPI: PCI Interrupt 0000:02:02.0[A] -> Link [LNKD] -> GSI 10 (level, low) -> IRQ 10
ssb: Sonics Silicon Backplane found on PCI device 0000:02:02.0 b44.c:v2.0
eth0: Broadcom 44xx/47xx 10/100BaseT Ethernet 00:c0:9f:29:99:a7 [...]

Ok, I prepared two debugging patches.

Please enable SonicsSiliconBackplane Debugging in the kernel kconfig, so I can get more detail information about your card. Device Drivers/Sonics Silicon Backplane/SSB debugging (Must disable "No SSB kernel messages")

Please apply and test the attached debugging patches in a row. So apply patch 1 and test if it works again. If not, apply patch 2 and test if it works.
Always save complete dmesg log on each test run and send it to me.

Quoted 8 lines
Quoted 3 lines

Thanks for testing.
(This time it seems we are actually getting somewhere, when dealing with sane people. :D )

I did the tests with my kernel where only the card is on interrupt 10. dmesg is attached.
With the first patch applied networking does work again. I also additionally tried patch2 and it also does work.

Great!
To me this seems to be a silicon bug. The IRQ routing value, which is read from the chip here, is hardcoded in the old b44 driver.
I'll implement a workaround for this and submit a patch.

Signature · 1 line
Greetings Michael.