Intel Clovertown vs. frequency scaling
Hi,
I have a number of Clovertown (intel quadcore) machines and, even with the latest 2.6.23, it seems to me that frequency scaling is not supported (e.g. the /sys/devices/system/cpu/cpu0/cpufreq/* stuff does not appear even though CONFIG_X86_SPEEDSTEP_CENTRINO is "y").
Is that as expected?
This is what the CPU (one core in one of the two sockets) looks like:
# head -24 /proc/cpuinfo processor : 0 vendor_id : GenuineIntel cpu family : 6 model : 15 model name : Intel(R) Xeon(R) CPU L5335 @ 2.00GHz stepping : 11 cpu MHz : 1995.105 cache size : 4096 KB physical id : 0 siblings : 4 core id : 0 cpu cores : 4 fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 10 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe nx lm constant_tsc arch_perfmon pebs bts pni monitor ds_cpl vmx tm2 ssse3 cx16 xtpr dca lahf_lm bogomips : 3994.09 clflush size : 64
also:
# cat /proc/acpi/processor/CPU0/info processor id: 0 acpi id: 0 bus mastering control: no power management: yes throttling control: yes limit interface: yes
# cat /proc/acpi/processor/CPU0/power
active state: C2
max_cstate: C8
bus master activity: 00000000
maximum allowed latency: 20000 usec
states:
C1: type[C1] promotion[C2] demotion[--] latency[020] usage[00003940] duration[00000000000000000000]
*C2: type[C2] promotion[--] demotion[C1] latency[040] usage[00013668] duration[00000000000359543325]FWIW, I also have some other Core-based (Woodcrest, Intel L5160) systems and cpufreq works fine there.
Any help or insight would be appreciated.
(I'm experimenting with ways to lower the average power consumption of a large number of servers, working my way through http://www.lesswatts.org
etc. I'm willing to patch kernels, run tests, and I have proper power meters to check the results.)
Andras
Quoted 4 lines · [email protected] wrote:
I have a number of Clovertown (intel quadcore) machines and, even with the latest 2.6.23, it seems to me that frequency scaling is not supported (e.g. the
/sys/devices/system/cpu/cpu0/cpufreq/*stuff does not appear even thoughCONFIG_X86_SPEEDSTEP_CENTRINOis "y").
I believe you want acpi-cpufreq, not speedstep-centrino. Works just fine for my quad-core systems, anyhow. If that doesn't work, its probably the bios at fault.
Signature · 2 lines
Jarod Wilson [email protected]
_______________________________________________
Cpufreq mailing list
[email protected]
http://lists.linux.org.uk/mailman/listinfo/cpufreq
I have a quad-core version that uses the centrino one (E5345). However, it only has two available speeds, 2GHz and 2.33GHz. Do you get more options?
[pcphuat27] ~ > cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_driver centrino
[pcphuat27] ~ > cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_available_frequencies 2333000 2000000
--
/------------------------------------+-------------------------\
|Stephen J. Gowdy, SLAC | CERN Office: 32-2-A22| |http://www.slac.stanford.edu/~gowdy/ | CH-1211 Geneva 23 | | | Switzerland | |EMail: [email protected] | Tel: +41 22 767 5840 |
\------------------------------------+-------------------------/
Quoted 7 lines · [email protected] wrote:
I have a number of Clovertown (intel quadcore) machines and, even with
the latest 2.6.23, it seems to me that frequency scaling is not
supported (e.g. the
/sys/devices/system/cpu/cpu0/cpufreq/*stuff doesnot appear even though
CONFIG_X86_SPEEDSTEP_CENTRINOis "y").
I believe you want acpi-cpufreq, not speedstep-centrino. Works just fine
for my quad-core systems, anyhow. If that doesn't work, its probably the
bios at fault.
Signature · 3 lines
Jarod Wilson [email protected]
_______________________________________________
Cpufreq mailing list
http://lists.linux.org.uk/mailman/listinfo/cpufreq
_______________________________________________
Cpufreq mailing list
[email protected]
http://lists.linux.org.uk/mailman/listinfo/cpufreq
Quoted 9 lines · Stephen J. Gowdy
I have a quad-core version that uses the centrino one (E5345). However, it only has two available speeds, 2GHz and 2.33GHz. Do you get more options?
[pcphuat27] ~ > cat
/sys/devices/system/cpu/cpu0/cpufreq/scaling_drivercentrino
[pcphuat27] ~ > cat/sys/devices/system/cpu/cpu0/cpufreq/scaling_available_frequencies2333000 2000000
Not a heck of a lot more, but a bit more.
[jwilson@xeus ~]$ cat sys/devices/system/cpu/cpu0/cpufreq/scaling_driver acpi-cpufreq
[jwilson@xeus ~]$ cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_available_frequencies 2660000 2128000 1596000
FYI, unless I'm mistaken, the speedstep-centrino driver is supposed to be getting deprecated in favor of acpi-cpufreq.
Quoted 9 lines
Quoted 4 lines · [email protected] wrote:
I have a number of Clovertown (intel quadcore) machines and, even with the latest 2.6.23, it seems to me that frequency scaling is not supported (e.g. the
/sys/devices/system/cpu/cpu0/cpufreq/*stuff does not appear even thoughCONFIG_X86_SPEEDSTEP_CENTRINOis "y").I believe you want acpi-cpufreq, not speedstep-centrino. Works just fine for my quad-core systems, anyhow. If that doesn't work, its probably the bios at fault.
Signature · 2 lines
Jarod Wilson [email protected]
_______________________________________________
Cpufreq mailing list
[email protected]
http://lists.linux.org.uk/mailman/listinfo/cpufreq
With latest kernels (2.6.22 and beyond) you should use acpi-cpufreq and not speedstep-centrino.
The frequencies supported depends on bus speed and voltages supported by the CPU. I think the thing here is you have a low voltage part which is already running at lowest possible voltage and does not support any more frequency/voltage reduction.
You mentioned that cpufreq works fine on Woodcrest, Intel L5160. What are the freqs supported and what is the max freq for this part?
Thanks,
Venki
Quoted 90 lines
-----Original Message-----
From: [email protected] [mailto:[email protected]] On Behalf Of [email protected]
Sent: Thursday, October 11, 2007 8:07 AM
To: [email protected]
Subject: Intel Clovertown vs. frequency scalingHi,
I have a number of Clovertown (intel quadcore) machines and, even with the latest 2.6.23, it seems to me that frequency scaling is not supported (e.g. the
/sys/devices/system/cpu/cpu0/cpufreq/*stuff does not appear even thoughCONFIG_X86_SPEEDSTEP_CENTRINOis "y").Is that as expected?
This is what the CPU (one core in one of the two sockets) looks like:
# head -24 /proc/cpuinfo processor : 0 vendor_id : GenuineIntel cpu family : 6 model : 15 model name : Intel(R) Xeon(R) CPU L5335 @ 2.00GHz stepping : 11 cpu MHz : 1995.105 cache size : 4096 KB physical id : 0 siblings : 4 core id : 0 cpu cores : 4 fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 10 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe nx lm constant_tsc arch_perfmon pebs bts pni monitor ds_cpl vmx tm2 ssse3 cx16 xtpr dca lahf_lm bogomips : 3994.09 clflush size : 64also:
# cat /proc/acpi/processor/CPU0/info processor id: 0 acpi id: 0 bus mastering control: no power management: yes throttling control: yes limit interface: yes# cat /proc/acpi/processor/CPU0/power active state: C2 max_cstate: C8 bus master activity: 00000000 maximum allowed latency: 20000 usec states: C1: type[C1] promotion[C2] demotion[--] latency[020] usage[00003940] duration[00000000000000000000] *C2: type[C2] promotion[--] demotion[C1] latency[040] usage[00013668] duration[00000000000359543325]FWIW, I also have some other Core-based (Woodcrest, Intel L5160) systems
and cpufreq works fine there.Any help or insight would be appreciated.
(I'm experimenting with ways to lower the average power consumption of a
large number of servers, working my way through
http://www.lesswatts.org
etc. I'm willing to patch kernels, run tests, and I have proper power meters to check the results.)Andras
_______________________________________________
Cpufreq mailing list
[email protected]
http://lists.linux.org.uk/mailman/listinfo/cpufreq
Quoted 2 lines
With latest kernels (2.6.22 and beyond) you should use acpi-cpufreq and not speedstep-centrino.
ah, thanks. :-) I found that that too was compiled in (and in fact that's what's driving the Woodcrest box as well).
Quoted 4 lines
The frequencies supported depends on bus speed and voltages supported by the CPU. I think the thing here is you have a low voltage part which is already running at lowest possible voltage and does not support any more frequency/voltage reduction.
Hm. So there are no P* states available (always running at top speed) but the CPU just goes to some C* state when it's idle?
This looks right (even if I find it strange) as the specs
(http://download.intel.com/design/Xeon/datashts/31556903.pdf ) say that "Note: Not all Quad-Core Intel® Xeon® Processor 5300 Series are capable of supporting Enhanced Intel SpeedStep Technology. More details on which processor frequencies will support this feature will be provided in future releases of the Quad-Core Intel® Xeon® Processor 5300 Series NDA Specification Update when available."
Nevertheless http://processorfinder.intel.com/details.aspx?sSpec=SLAEN
says the L5335 has Enhanced Intel Speedstep support.
Quoted 2 lines
You mentioned that cpufreq works fine on Woodcrest, Intel L5160. What are the freqs supported and what is the max freq for this part?
As I said I was mistaken and it's using acpi-cpufreq. However, this:
model name : Intel(R) Xeon(R) CPU 5160 @ 3.00GHz
supports the following frequencies (2.6.23):
# cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_available_frequencies 2997000 2664000 2331000 1998000
Also, I have found myself another Clovertown:
model name : Intel(R) Xeon(R) CPU E5345 @ 2.33GHz
and this seems not to support no frequency scaling, no C-states, only thermal throttling. Can this be true? From the specs mentioned above I'd have expected at least some sort of halt state.
http://processorfinder.intel.com/details.aspx?sSpec=SL9YL says 'enhanced intel speedstep' and C1E support, same as Mr. L5335 above.
I'm getting more and more confused about this :)
Andras
Quoted 19 lines
-----Original Message-----
From: [email protected] [mailto:[email protected]] On Behalf Of [email protected]
Sent: Friday, October 12, 2007 8:01 AM
To: [email protected]
Subject: Re: Intel Clovertown vs. frequency scalingQuoted 1 line
With latest kernels (2.6.22 and beyond) you should use
acpi-cpufreq and
Quoted 1 line
not speedstep-centrino.
ah, thanks. :-) I found that that too was compiled in (and in fact that's what's driving the Woodcrest box as well).
Quoted 1 line
The frequencies supported depends on bus speed and voltages
supported by
Quoted 8 lines
Quoted 1 line
the CPU. I think the thing here is you have a low voltage
part which is
Quoted 1 line
already running at lowest possible voltage and does not
support any more
Quoted 1 line
frequency/voltage reduction.
Hm. So there are no P* states available (always running at top speed) but the CPU just goes to some C* state when it's idle?
Correct. On idle CPU will consume much less power than top speed, as it will go to C-state.
Quoted 4 lines
This looks right (even if I find it strange) as the specs
(http://download.intel.com/design/Xeon/datashts/31556903.pdf ) say that "Note: Not all Quad-Core Intel(r) Xeon(r) Processor 5300 Series are
capable
Quoted 4 lines
of supporting Enhanced Intel SpeedStep Technology. More details on which
processor frequencies will support this feature will be provided in future releases of the Quad-Core Intel(r) Xeon(r) Processor 5300 Series
NDA
Quoted 5 lines
Specification Update when available."
Nevertheless http://processorfinder.intel.com/details.aspx?sSpec=SLAEN
says the L5335 has Enhanced Intel Speedstep support.
Yes. I noticed the processorfinder thing yesterday and trying to get people to add clarification onto that page.
Quoted 5 lines
Quoted 2 lines
You mentioned that cpufreq works fine on Woodcrest, Intel L5160. What are the freqs supported and what is the max freq for this part?
As I said I was mistaken and it's using acpi-cpufreq. However, this:
Quoted 8 lines
model name : Intel(R) Xeon(R) CPU 5160 @ 3.00GHz
supports the following frequencies (2.6.23):
# cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_available_frequencies 2997000 2664000 2331000 1998000
That seems correct.
Quoted 11 lines
Also, I have found myself another Clovertown:
model name : Intel(R) Xeon(R) CPU E5345 @ 2.33GHzand this seems not to support no frequency scaling, no C-states, only thermal throttling. Can this be true? From the specs mentioned above I'd
have expected at least some sort of halt state.
http://processorfinder.intel.com/details.aspx?sSpec=SL9YL says 'enhanced
intel speedstep' and C1E support, same as Mr. L5335 above.
Hmmm. This processor should support 2GHz frequency. Most probably BIOS is not providing information for the driver to enable speedstep here. Can you make sure you have the latest BIOS and also check whether there are any options to enable speedstep in BIOS setup. Send me the output of acpidump (you can find acpidump in latest pmtools package here -
http://www.kernel.org/pub/linux/kernel/people/lenb/acpi/utils/ ). I can take a look at what BIOS is saying about speedstep.
Thanks,
Venki
(sorry for the late reply)
Quoted 2 lines
Hmmm. This processor should support 2GHz frequency. Most probably BIOS is not providing information for the driver to enable speedstep here.
This is embarassing, the option (named "EIST support") was off. Turning it on resulted in
# cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_available_frequencies 2333000 2000000
but no C-state info (like on the L5335) with 2.6.23 and acpi-cpufreq.
Quoted 5 lines
Can you make sure you have the latest BIOS and also check whether there are any options to enable speedstep in BIOS setup. Send me the output of acpidump (you can find acpidump in latest pmtools package here -
http://www.kernel.org/pub/linux/kernel/people/lenb/acpi/utils/ ). I can take a look at what BIOS is saying about speedstep.
Hm... I may be missing something again, but acpidump doesn't find the RSD PTR table, and dmesg doesn't help either (all ACPI-related options are enabled in the BIOS):
root@pcitfiot05:/usr/src/pmtools-20070714/acpidump# ./acpidump ACPI tables were not found. If you know location of RSD PTR table (from dmesg, etc), supply it with either --addr or -a option root@pcitfiot05:/usr/src/pmtools-20070714/acpidump# dmesg | grep ACPI | head -20 BIOS-e820: 00000000cff60000 - 00000000cff69000 (ACPI data) BIOS-e820: 00000000cff69000 - 00000000cff80000 (ACPI NVS) ACPI: RSDP 000F6030, 0014 (r0 PTLTD ) ACPI: RSDT CFF63C39, 003C (r1 PTLTD RSDT 6040000 LTP 0) ACPI: FACP CFF68E10, 0074 (r1 INTEL TUMWATER 6040000 PTL 3) ACPI: DSDT CFF65C59, 31B7 (r1 Intel BLAKFORD 6040000 MSFT 100000E) ACPI: FACS CFF69FC0, 0040 ACPI: APIC CFF68E84, 00C8 (r1 PTLTD APIC 6040000 LTP 0) ACPI: MCFG CFF68F4C, 003C (r1 PTLTD MCFG 6040000 LTP 0) ACPI: BOOT CFF68F88, 0028 (r1 PTLTD $SBFTBL$ 6040000 LTP 1) ACPI: SPCR CFF68FB0, 0050 (r1 PTLTD $UCRTBL$ 6040000 PTL 1) ACPI: SSDT CFF63C75, 1405 (r1 PmRef CpuPm 3000 INTL 20050228) ACPI: PM-Timer IO Port: 0x1008 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) ACPI: LAPIC (acpi_id[0x01] lapic_id[0x04] enabled) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) ACPI: LAPIC (acpi_id[0x03] lapic_id[0x05] enabled) ACPI: LAPIC (acpi_id[0x04] lapic_id[0x02] enabled) ACPI: LAPIC (acpi_id[0x05] lapic_id[0x06] enabled)
This is with the latest BIOS (Supermicro X7DBT, 1.3c); it has an option called "Processor Power Management" which can be set to either
"GV1/GV3 only" - according to the BIOS, this enables GV1/GV3 (whatever that is) but no C states. This is what I use.
"Disabled" - which disables everything.
According to the BIOS help there should be two more settings to that that give me C states but those are only described, they don't appear in the selection box.
Two more options called "Thermal Management 2" and "C1 Enhanced Mode" were also enabled, still no C states.
I guess I'll be nagging Supermicro about this.
thanks again,
Andras
Quoted 4 lines · [email protected] writes:
According to the BIOS help there should be two more settings to that that give me C states but those are only described, they don't appear in the selection box.
Desktop/Server boxes normally don't have any deeper C states than C1 and C1 is just the traditional "HLT" instruction and doesn't need ACPI support at all and is usually not described in ACPI tables when it's the only state.
The BIOS options likely just control what the BIOS' SMM handler does hidden inside C1.
-Andi