Problem: OOPS in khubd on disconnect of Labtec USB Headset
OOPS in khubd on disconnect of Labtec USB Headset
Linux version 2.6.23.1 (alsobrsp@karma) (gcc version 4.1.3 20070831 (prerelease) (Debian 4.1.2-16)) #5 SMP PREEMPT Sat Oct 20 11:53:38 EDT 2007
BUG: unable to handle kernel paging request at virtual address 00100100 printing eip: f89b5faa *pde = 00000000 Oops: 0000 [#1] PREEMPT SMP Modules linked in: snd_rtctimer dv1394 raw1394 nfsd exportfs auth_rpcgss ppdev
lp fan ac battery autofs4 nfs lockd nfs_acl sunrpc ipv6 fuse dm_snapshot dm_mirror dm_mod rtc_rs5c372 rtc_rs5c348 rtc_v3020 rtc_x1205 rtc_pcf8563 rtc_max6902 rtc_m48t86 rtc_isl1208 rtc_ds1742 rtc_ds1672 rtc_ds1553 rtc_ds1307 rtc_cmos lm85 hwmon_vid loop sg sr_mod usblp snd_emu10k1_synth snd_usb_audio snd_emux_synth snd_usb_lib snd_seq_virmidi snd_seq_midi_emul snd_emu10k1 snd_seq_dummy snd_seq_oss snd_seq_midi snd_seq_midi_event snd_seq snd_rawmidi snd_ac97_codec ac97_bus snd_pcm_oss snd_mixer_oss snd_pcm snd_seq_device snd_timer snd_page_alloc snd_util_mem snd_hwdep snd ohci1394 parport_pc parport ieee1394 emu10k1_gp gameport soundcore tg3 ohci_hcd floppy pcspkr rtc thermal button psmouse usb_storage processor generic i2c_i801 serio_raw iTCO_wdt piix i2c_core intel_agp agpgart shpchp pci_hotplug ide_disk tsdev joydev evdev
CPU: 0 EIP: 0060:[<f89b5faa>] Not tainted VLI EFLAGS: 00010246 (2.6.23.1 #5)
EIP is at snd_ctl_dev_disconnect+0x4b/0x7c [snd]
eax: ef6ade70 ebx: 00100100 ecx: 00020004 edx: 0000001d
esi: f7fd6200 edi: f7fd634c ebp: f78f1800 esp: c217de70
ds: 007b es: 007b fs: 00d8 gs: 0000 ss: 0068
Process khubd (pid: 153, ti=c217c000 task=c217e790 task.ti=c217c000)
Stack: 00000000 f79ec600 f7fd6200 00000000 f89b7a88 00000213 f79ec600 f7fd6200
f89b7cb7 00000000 f7fd6200 f8b51a20 f89b4dcc c031ad37 c0288fb9 f7f81800
c20e8d80 f8b41631 f7fd6200 f7f81800 f7f8181c f8b51a20 f78f1800 c0289b7c
Call Trace:
[<f89b7a88>] snd_device_disconnect+0x28/0x60 [snd]
[<f89b7cb7>] snd_device_disconnect_all+0x19/0x3e [snd]
[<f89b4dcc>] snd_card_disconnect+0x11b/0x13f [snd]
[<c031ad37>] _spin_unlock_irqrestore+0xf/0x23
[<c0288fb9>] usb_autopm_do_device+0xc7/0xd1
[<f8b41631>] usb_audio_disconnect+0x44/0xea [snd_usb_audio]
[<c0289b7c>] usb_unbind_interface+0x44/0x94
[<c024fb8c>] __device_release_driver+0x71/0x8e
[<c024ff14>] device_release_driver+0x1e/0x34
[<c024f587>] bus_remove_device+0x6d/0x7dBUG: unable to handle kernel paging request at virtual address 00100100
printing eip:f89b5faa
*pde = 00000000
Oops: 0000 [#1] PREEMPT SMP Modules linked in: snd_rtctimer dv1394 raw1394 nfsd exportfs auth_rpcgss ppdev
lp fan ac battery autofs4 nfs lockd nfs_acl sunrpc ipv6 fuse dm_snapshot dm_mirror dm_mod rtc_rs5c372 rtc_rs5c348 rtc_v3020 rtc_x1205 rtc_pcf8563 rtc_max6902 rtc_m48t86 rtc_isl1208 rtc_ds1742 rtc_ds1672 rtc_ds1553 rtc_ds1307 rtc_cmos lm85 hwmon_vid loop sg sr_mod usblp snd_emu10k1_synth snd_usb_audio snd_emux_synth snd_usb_lib snd_seq_virmidi snd_seq_midi_emul snd_emu10k1 snd_seq_dummy snd_seq_oss snd_seq_midi snd_seq_midi_event snd_seq snd_rawmidi snd_ac97_codec ac97_bus snd_pcm_oss snd_mixer_oss snd_pcm snd_seq_device snd_timer snd_page_alloc snd_util_mem snd_hwdep snd ohci1394 parport_pc parport ieee1394 emu10k1_gp gameport soundcore tg3 ohci_hcd floppy pcspkr rtc thermal button psmouse usb_storage processor generic i2c_i801 serio_raw iTCO_wdt piix i2c_core intel_agp agpgart shpchp pci_hotplug ide_disk tsdev joydev evdev
CPU: 0 EIP: 0060:[<f89b5faa>] Not tainted VLI EFLAGS: 00010246 (2.6.23.1 #5)
EIP is at snd_ctl_dev_disconnect+0x4b/0x7c [snd]
eax: ef6ade70 ebx: 00100100 ecx: 00020004 edx: 0000001d
esi: f7fd6200 edi: f7fd634c ebp: f78f1800 esp: c217de70
ds: 007b es: 007b fs: 00d8 gs: 0000 ss: 0068
Process khubd (pid: 153, ti=c217c000 task=c217e790 task.ti=c217c000)
Stack: 00000000 f79ec600 f7fd6200 00000000 f89b7a88 00000213 f79ec600 f7fd6200
f89b7cb7 00000000 f7fd6200 f8b51a20 f89b4dcc c031ad37 c0288fb9 f7f81800
c20e8d80 f8b41631 f7fd6200 f7f81800 f7f8181c f8b51a20 f78f1800 c0289b7c
Call Trace:
[<f89b7a88>] snd_device_disconnect+0x28/0x60 [snd]
[<f89b7cb7>] snd_device_disconnect_all+0x19/0x3e [snd]
[<f89b4dcc>] snd_card_disconnect+0x11b/0x13f [snd]
[<c031ad37>] _spin_unlock_irqrestore+0xf/0x23
[<c0288fb9>] usb_autopm_do_device+0xc7/0xd1
[<f8b41631>] usb_audio_disconnect+0x44/0xea [snd_usb_audio]
[<c0289b7c>] usb_unbind_interface+0x44/0x94
[<c024fb8c>] __device_release_driver+0x71/0x8e
[<c024ff14>] device_release_driver+0x1e/0x34
[<c024f587>] bus_remove_device+0x6d/0x7d
[<c024dd7d>] device_del+0x1cc/0x240
[<c0287525>] usb_disable_device+0x5c/0xbb
[<c0283c55>] usb_disconnect+0x83/0x11b
[<c0284363>] hub_thread+0x388/0xa8d
[<c0133e18>] autoremove_wake_function+0x0/0x35
[<c0283fdb>] hub_thread+0x0/0xa8d
[<c0133d49>] kthread+0x38/0x5f
[<c0133d11>] kthread+0x0/0x5f
[<c0104aa7>] kernel_thread_helper+0x7/0x10
=======================
Code: 18 c7 04 24 00 00 00 00 b9 01 00 00 00 ba 03 00 00 00 e8 41 68 76 c7 8d 43 30 b9 04 00 02 00 ba 1d 00 00 00 e8 32 b2 7b c7 8b 1b <8b> 03 0f 18 00 90 8d 86 78 01 00 00 39 c3 75 c3 89 f8 e8 6d 0f
EIP: [<f89b5faa>] snd_ctl_dev_disconnect+0x4b/0x7c [snd] SS:ESP 0068:c217de70
[<c024dd7d>] device_del+0x1cc/0x240 [<c0287525>] usb_disable_device+0x5c/0xbb [<c0283c55>] usb_disconnect+0x83/0x11b [<c0284363>] hub_thread+0x388/0xa8d [<c0133e18>] autoremove_wake_function+0x0/0x35 [<c0283fdb>] hub_thread+0x0/0xa8d [<c0133d49>] kthread+0x38/0x5f [<c0133d11>] kthread+0x0/0x5f [<c0104aa7>] kernel_thread_helper+0x7/0x10 ======================= Code: 18 c7 04 24 00 00 00 00 b9 01 00 00 00 ba 03 00 00 00 e8 41 68 76 c7 8d
43 30 b9 04 00 02 00 ba 1d 00 00 00 e8 32 b2 7b c7 8b 1b <8b> 03 0f 18 00 90 8d 86 78 01 00 00 39 c3 75 c3 89 f8 e8 6d 0f
EIP: [<f89b5faa>] snd_ctl_dev_disconnect+0x4b/0x7c [snd] SS:ESP 0068:c217de70
If some fields are empty or look unusual you may have an old version. Compare to the current minimal requirements in Documentation/Changes.
Linux karma 2.6.23.1 #5 SMP PREEMPT Sat Oct 20 11:53:38 EDT 2007 i686 GNU/Linux
Gnu C 4.1.3 Gnu make 3.81 binutils Binutils util-linux 2.13 mount 2.13 module-init-tools 3.3-pre11 e2fsprogs 1.40.2 PPP 2.4.4 Linux C Library 6.1 Dynamic linker (ldd) 2.6.1 Procps 3.2.7 Net-tools 1.60 Console-tools 0.2.3 Sh-utils 5.97 udev 114 wireless-tools 29
0000-001f : dma1
0020-0021 : pic1
0040-0043 : timer0
0050-0053 : timer1
0060-006f : keyboard
0070-0077 : rtc
0080-008f : dma page reg
00a0-00a1 : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : 0000:00:1f.1
0170-0177 : ide1
01f0-01f7 : 0000:00:1f.1
01f0-01f7 : ide0
02f8-02ff : serial
0376-0376 : 0000:00:1f.1
0376-0376 : ide1
0378-037a : parport0
03c0-03df : vga+
03f2-03f5 : floppy
03f6-03f6 : 0000:00:1f.1
03f6-03f6 : ide0
03f7-03f7 : floppy DIR
03f8-03ff : serial
0400-041f : pnp 00:0c
0420-043f : pnp 00:0c
0440-045f : pnp 00:0c
0460-047f : pnp 00:0c
0460-0461 : ACPI PM1b_CNT_BLK
04d0-04d1 : pnp 00:0b
0778-077a : parport0
0cf8-0cff : PCI conf1
1000-1fff : PCI Bus #05
1000-101f : 0000:05:09.0
1000-101f : EMU10K1
1020-1027 : 0000:05:09.1
1020-1027 : emu10k1-gp2440-245f : 0000:00:1d.0
2440-245f : uhci_hcd
2460-247f : 0000:00:1d.1
2460-247f : uhci_hcd
2480-249f : 0000:00:1d.2
2480-249f : uhci_hcd
24c0-24cf : 0000:00:1f.1
24d0-24df : 0000:00:1f.2
24d0-24df : libata
24e0-24e7 : 0000:00:02.0
24f8-24ff : 0000:00:1f.2
24f8-24ff : libata
2800-2807 : 0000:00:1f.2
2800-2807 : libata
2810-2813 : 0000:00:1f.2
2810-2813 : libata
2814-2817 : 0000:00:1f.2
2814-2817 : libata
f800-f87f : 0000:00:1f.0
f800-f81f : pnp 00:0c
f800-f803 : ACPI PM1a_EVT_BLK
f804-f805 : ACPI PM1a_CNT_BLK
f808-f80b : ACPI PM_TMR
f810-f815 : ACPI CPU throttle
f820-f83f : pnp 00:0c
f828-f82f : ACPI GPE0_BLK f840-f85f : pnp 00:0c
f860-f87f : pnp 00:0c
fa00-fa3f : 0000:00:1f.0
fc00-fc1f : 0000:00:1f.3
fc00-fc1f : i801_smbus
00000000-0009fbff : System RAM
00000000-00000000 : Crash kernel
0009fc00-0009ffff : reserved
000a0000-000bffff : Video RAM area
000c0000-000ca5ff : Video ROM
000f0000-000fffff : System ROM
00100000-7f7effff : System RAM
00100000-0031bc4f : Kernel code
0031bc50-003f3f23 : Kernel data
7f7f0000-7fffffff : reserved
88000000-880003ff : 0000:00:1f.1
e0000000-efffffff : 0000:00:00.0
f0000000-f7ffffff : 0000:00:02.0
f8400000-f847ffff : 0000:00:02.0
f8480000-f84803ff : 0000:00:1d.7
f8480000-f84803ff : ehci_hcd
f8500000-f87fffff : PCI Bus #05
f8500000-f850ffff : 0000:05:02.0
f8500000-f850ffff : tg3
f8510000-f8513fff : 0000:05:09.2
f8514000-f8514fff : 0000:05:04.0
f8514000-f8514fff : ohci_hcd
f8515000-f8515fff : 0000:05:04.1
f8515000-f8515fff : ohci_hcd
f8516000-f85167ff : 0000:05:09.2
f8516000-f85167ff : ohci1394
f8516800-f85168ff : 0000:05:04.2
f8516800-f85168ff : ehci_hcdfec00000-ffffffff : reserved
00:00.0 Host bridge: Intel Corporation 82865G/PE/P DRAM Controller/Host-Hub Interface (rev 02)
Subsystem: Hewlett-Packard Company Unknown device 12bc
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=256M]
Capabilities: [e4] Vendor Specific Information
00:02.0 VGA compatible controller: Intel Corporation 82865G Integrated Graphics Controller (rev 02) (prog-if 00 [VGA])
Subsystem: Hewlett-Packard Company D530 sff(dc578av)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 10
Region 0: Memory at f0000000 (32-bit, prefetchable) [size=128M] Region 1: Memory at f8400000 (32-bit, non-prefetchable) [size=512K] Region 2: I/O ports at 24e0 [size=8]
Capabilities: [d0] Power Management version 1
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mAPME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1d.0 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #1 (rev 02) (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company d530 CMT (DG746A)
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 19
Region 4: I/O ports at 2440 [size=32]
00:1d.1 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #2 (rev 02) (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company d530 CMT (DG746A)
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 20
Region 4: I/O ports at 2460 [size=32]
00:1d.2 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #3 (rev 02) (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company d530 CMT (DG746A)
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 16
Region 4: I/O ports at 2480 [size=32]
00:1d.7 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB2 EHCI Controller (rev 02) (prog-if 20 [EHCI])
Subsystem: Hewlett-Packard Company d530 CMT (DG746A)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 17
Region 0: Memory at f8480000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mAPME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev c2) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=05, subordinate=05, sec-latency=64
I/O behind bridge: 00001000-00001fff
Memory behind bridge: f8500000-f87fffff
Prefetchable memory behind bridge: fff00000-000fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
00:1f.0 ISA bridge: Intel Corporation 82801EB/ER (ICH5/ICH5R) LPC Interface Bridge (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:1f.1 IDE interface: Intel Corporation 82801EB/ER (ICH5/ICH5R) IDE Controller (rev 02) (prog-if 8a [Master SecP PriP])
Subsystem: Hewlett-Packard Company d530 CMT (DG746A)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at 24c0 [size=16]
Region 5: Memory at 88000000 (32-bit, non-prefetchable) [size=1K]00:1f.2 IDE interface: Intel Corporation 82801EB (ICH5) SATA Controller (rev
02) (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: Hewlett-Packard Company d530 CMT (DG746A)
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at 24f8 [size=8]
Region 1: I/O ports at 2810 [size=4]
Region 2: I/O ports at 2800 [size=8]
Region 3: I/O ports at 2814 [size=4]
Region 4: I/O ports at 24d0 [size=16]00:1f.3 SMBus: Intel Corporation 82801EB/ER (ICH5/ICH5R) SMBus Controller (rev
02)
Subsystem: Hewlett-Packard Company Unknown device 12bc
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at fc00 [size=32]
05:02.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5782 Gigabit Ethernet (rev 03)
Subsystem: Hewlett-Packard Company d530 CMT (DG746A)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (16000ns min)
Interrupt: pin A routed to IRQ 22
Region 0: Memory at f8500000 (64-bit, non-prefetchable) [size=64K]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mAPME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
Capabilities: [58] Message Signalled Interrupts: Mask- 64bit+
Queue=0/3 Enable-
Address: 7fff7fef4ffebffc Data: ffff
05:04.0 USB Controller: NEC Corporation USB (rev 41) (prog-if 10 [OHCI])
Subsystem: Asustek Computer, Inc. PCI-USB2 (OHCI subsystem)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (250ns min, 10500ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at f8514000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mAPME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
05:04.1 USB Controller: NEC Corporation USB (rev 41) (prog-if 10 [OHCI])
Subsystem: Asustek Computer, Inc. PCI-USB2 (OHCI subsystem)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (250ns min, 10500ns max), Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 16
Region 0: Memory at f8515000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mAPME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
05:04.2 USB Controller: NEC Corporation USB 2.0 (rev 02) (prog-if 20 [EHCI])
Subsystem: Asustek Computer, Inc. PCI-USB2 (EHCI subsystem)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (4000ns min, 8500ns max), Cache Line Size: 128 bytes
Interrupt: pin C routed to IRQ 18
Region 0: Memory at f8516800 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mAPME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
05:09.0 Multimedia audio controller: Creative Labs SB Audigy (rev 03)
Subsystem: Creative Labs SB0090 Audigy Player
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (500ns min, 5000ns max)
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at 1000 [size=32]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mAPME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
05:09.1 Input device controller: Creative Labs SB Audigy Game Port (rev 03)
Subsystem: Creative Labs SB Audigy MIDI/Game Port
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Region 0: I/O ports at 1020 [size=8]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mAPME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
05:09.2 FireWire (IEEE 1394): Creative Labs SB Audigy FireWire Port (prog-if 10 [OHCI])
Subsystem: Creative Labs SB Audigy FireWire Port
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 66 (500ns min, 1000ns max), Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 18
Region 0: Memory at f8516000 (32-bit, non-prefetchable) [size=2K] Region 1: Memory at f8510000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mAPME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME+
Signature · 4 lines
Syd Alsobrook IT Tag Team, Inc. 518-598-6025 http://www.ittagteam.com
Quoted 46 lines · On Mon, 22 Oct 2007 15:03:54 -0400 Syd Alsobrook <[email protected]> wrote:
OOPS in khubd on disconnect of Labtec USB Headset
Linux version 2.6.23.1 (alsobrsp@karma) (gcc version 4.1.3 20070831 (prerelease) (Debian 4.1.2-16)) #5 SMP PREEMPT Sat Oct 20 11:53:38 EDT 2007
BUG: unable to handle kernel paging request at virtual address 00100100 printing eip: f89b5faa *pde = 00000000 Oops: 0000 [#1] PREEMPT SMP Modules linked in: snd_rtctimer dv1394 raw1394 nfsd exportfs auth_rpcgss ppdevlp fan ac battery autofs4 nfs lockd
nfs_aclsunrpc ipv6 fusedm_snapshotdm_mirrordm_modrtc_rs5c372rtc_rs5c348rtc_v3020rtc_x1205rtc_pcf8563rtc_max6902rtc_m48t86rtc_isl1208rtc_ds1742rtc_ds1672rtc_ds1553rtc_ds1307rtc_cmoslm85hwmon_vidloop sgsr_modusblpsnd_emu10k1_synthsnd_usb_audiosnd_emux_synthsnd_usb_libsnd_seq_virmidisnd_seq_midi_emulsnd_emu10k1snd_seq_dummysnd_seq_osssnd_seq_midisnd_seq_midi_eventsnd_seqsnd_rawmidisnd_ac97_codecac97_bussnd_pcm_osssnd_mixer_osssnd_pcmsnd_seq_devicesnd_timersnd_page_allocsnd_util_memsnd_hwdepsnd ohci1394parport_pcparport ieee1394emu10k1_gpgameport soundcore tg3ohci_hcdfloppy pcspkr rtc thermal button psmouseusb_storageprocessor generici2c_i801serio_rawiTCO_wdtpiixi2c_coreintel_agpagpgart shpchppci_hotplugide_disktsdev joydev evdevCPU: 0 EIP: 0060:[<f89b5faa>] Not tainted VLI EFLAGS: 00010246 (2.6.23.1 #5)EIP is at
snd_ctl_dev_disconnect+0x4b/0x7c[snd]
eax:ef6ade70ebx: 00100100 ecx: 00020004 edx:0000001d
esi:f7fd6200edi:f7fd634cebp:f78f1800esp:c217de70
ds: 007b es: 007b fs: 00d8 gs: 0000 ss: 0068
Process khubd (pid: 153, ti=c217c000 task=c217e790 task.ti=c217c000)Stack: 00000000 f79ec600 f7fd6200 00000000 f89b7a88 00000213 f79ec600 f7fd6200 f89b7cb7 00000000 f7fd6200 f8b51a20 f89b4dcc c031ad37 c0288fb9 f7f81800 c20e8d80 f8b41631 f7fd6200 f7f81800 f7f8181c f8b51a20 f78f1800 c0289b7c Call Trace: [<f89b7a88>] snd_device_disconnect+0x28/0x60 [snd] [<f89b7cb7>] snd_device_disconnect_all+0x19/0x3e [snd] [<f89b4dcc>] snd_card_disconnect+0x11b/0x13f [snd] [<c031ad37>] _spin_unlock_irqrestore+0xf/0x23 [<c0288fb9>] usb_autopm_do_device+0xc7/0xd1 [<f8b41631>] usb_audio_disconnect+0x44/0xea [snd_usb_audio] [<c0289b7c>] usb_unbind_interface+0x44/0x94 [<c024fb8c>] __device_release_driver+0x71/0x8e [<c024ff14>] device_release_driver+0x1e/0x34 [<c024f587>] bus_remove_device+0x6d/0x7dBUG: unable to handle kernel paging
Quoted 3 lines
request at virtual address 00100100
printing eip:f89b5faa
Did any earlier kernel work OK? If so, can you tell us which version(s)?
Thanks.
Quoted 8 lines · you
Quoted 5 lines · On Mon, 22 Oct 2007 15:03:54 -0400 Syd Alsobrook <[email protected]> wrote:
OOPS in khubd on disconnect of Labtec USB Headset
Linux version 2.6.23.1 (alsobrsp@karma) (gcc version 4.1.3 20070831 (prerelease) (Debian 4.1.2-16)) #5 SMP PREEMPT Sat Oct 20 11:53:38 EDT 2007
Did any earlier kernel work OK? If so, can you tell us which version(s)?
This worked with the Debian packaged version of kernel 2.6.22. The specific package is linux-image-2.6.22-2-686 version 2.6.22-4. The problem report is for a custom compiled kernel.
Syd
Signature · 4 lines
Syd Alsobrook IT Tag Team, Inc. 518-598-6025 http://www.ittagteam.com