ppc4xx: Add initial esd PMC440 board support

211 lines not on this page · raw message

index b9916e2..5601080 100644
@@ -33,7 +33,7 @@ static struct serial_device *serial_devices = NULL;
 static struct serial_device *serial_current = NULL;
 
 #if !defined(CONFIG_LWMON) && !defined(CONFIG_PXA27X)
-struct serial_device *default_serial_console (void)
+struct serial_device *__default_serial_console (void)
 {
 #if defined(CONFIG_8xx_CONS_SMC1) || defined(CONFIG_8xx_CONS_SMC2)
 	return &serial_smc_device;

@@ -64,6 +64,8 @@ struct serial_device *default_serial_console (void)
 #error No default console
 #endif
 }
+
+struct serial_device *default_serial_console(void) __attribute__((weak, alias("__default_serial_console")));
 #endif
 
 int serial_register (struct serial_device *dev)

712 lines not on this page · raw message

148 lines not on this page · raw message

similarity index 100%
copy from board/amcc/sequoia/sdram.c
copy to board/esd/pmc440/sdram.c

similarity index 100%
copy from board/amcc/sequoia/sdram.h
copy to board/esd/pmc440/sdram.h

new file mode 100644
index 0000000..6178dff
@@ -0,0 +1,555 @@
+/*
+ * (C) Copyright 2007
+ * Matthias Fuchs, esd Gmbh, matthias.fuchs at esd-electronics.com.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ */
+
+#include <common.h>
+#include <command.h>
+#include <asm/io.h>
+
+#include <asm/processor.h>
+
+#include "pmc440.h"
+
+int is_monarch(void);
+int bootstrap_eeprom_write(unsigned dev_addr, unsigned offset, uchar *buffer, unsigned cnt);
+int eeprom_write_enable(unsigned dev_addr, int state);
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#ifdef CONFIG_CMD_BSP
+
+static int got_fifoirq;
+static int got_hcirq;
+
+int fpga_interrupt(u32 arg)
+{
+	pmc440_fpga_t *fpga = (pmc440_fpga_t *)arg;
+	int rc = -1; /* not for us */
+	u32 status = FPGA_IN32(&fpga->status);
+
+	/* check for interrupt from fifo module */
+	if (status & STATUS_FIFO_ISF) {
+		/* disable this int source */
+		FPGA_OUT32(&fpga->hostctrl, HOSTCTRL_FIFOIE_GATE);
+		rc = 0;
+		got_fifoirq = 1; /* trigger backend */
+	}
+
+	if (status & STATUS_HOST_ISF) {
+		FPGA_OUT32(&fpga->hostctrl, HOSTCTRL_HCINT_GATE);
+		rc = 0;
+		got_hcirq = 1;
+	}
+
+	return rc;
+}
+
+
+int do_waithci(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
+{
+	pmc440_fpga_t *fpga = (pmc440_fpga_t *)FPGA_BA;
+
+	got_hcirq = 0;
+
+	FPGA_CLRBITS(&fpga->ctrla, CTRL_HOST_IE);
+	FPGA_OUT32(&fpga->hostctrl, HOSTCTRL_HCINT_GATE);
+
+	irq_install_handler(IRQ0_FPGA,
+			    (interrupt_handler_t *)fpga_interrupt,
+			    fpga);
+
+	FPGA_SETBITS(&fpga->ctrla, CTRL_HOST_IE);
+
+	while (!got_hcirq) {
+		/* Abort if ctrl-c was pressed */
+		if (ctrlc()) {
+			puts("\nAbort\n");
+			break;
+		}
+	}
+	if (got_hcirq)
+		printf("Got interrupt!\n");
+
+	FPGA_CLRBITS(&fpga->ctrla, CTRL_HOST_IE);
+	irq_free_handler(IRQ0_FPGA);
+	return 0;
+}
+U_BOOT_CMD(
+	waithci,	1,	1,	do_waithci,
+	"waithci - Wait for host control interrupt\n",
+	NULL
+	);
+
+
+void dump_fifo(pmc440_fpga_t *fpga, int f, int *n)
+{
+	u32 ctrl;
+
+	while (!((ctrl = FPGA_IN32(&fpga->fifo[f].ctrl)) & FIFO_EMPTY)) {
+		printf("%5d  %d    %3d  %08x",
+		       (*n)++, f, ctrl & (FIFO_LEVEL_MASK | FIFO_FULL),
+		       FPGA_IN32(&fpga->fifo[f].data));
+		if (ctrl & FIFO_OVERFLOW) {
+			printf(" OVERFLOW\n");
+			FPGA_CLRBITS(&fpga->fifo[f].ctrl, FIFO_OVERFLOW);
+		} else
+			printf("\n");
+	}
+}
+
+
+int do_fifo(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
+{
+	pmc440_fpga_t *fpga = (pmc440_fpga_t *)FPGA_BA;
+	int i;
+	int n = 0;
+	u32 ctrl, data, f;
+	char str[] = "\\|/-";
+	int abort = 0;
+	int count = 0;
+	int count2 = 0;
+
+	switch (argc) {
+	case 1:
+		/* print all fifos status information */
+		printf("fifo level status\n");
+		printf("______________________________\n");
+		for (i=0; i<FIFO_COUNT; i++) {
+			ctrl = FPGA_IN32(&fpga->fifo[i].ctrl);
+			printf(" %d    %3d  %s%s%s %s\n",
+			       i, ctrl & (FIFO_LEVEL_MASK | FIFO_FULL),
+			       ctrl & FIFO_FULL ? "FULL     " : "",
+			       ctrl & FIFO_EMPTY ? "EMPTY    " : "",
+			       ctrl & (FIFO_FULL|FIFO_EMPTY) ? "" : "NOT EMPTY",
+			       ctrl & FIFO_OVERFLOW ? "OVERFLOW" : "");
+		}
+		break;
+
+	case 2:
+		/* completely read out fifo 'n' */
+		if (!strcmp(argv[1],"read")) {
+			printf("  #   fifo level data\n");
+			printf("______________________________\n");
+
+			for (i=0; i<FIFO_COUNT; i++)
+				dump_fifo(fpga, i, &n);
+
+		} else if (!strcmp(argv[1],"wait")) {
+			got_fifoirq = 0;
+
+			irq_install_handler(IRQ0_FPGA,
+					    (interrupt_handler_t *)fpga_interrupt,
+					    fpga);
+
+			printf("  #   fifo level data\n");
+			printf("______________________________\n");
+
+			/* enable all fifo interrupts */
+			FPGA_OUT32(&fpga->hostctrl,
+				   HOSTCTRL_FIFOIE_GATE | HOSTCTRL_FIFOIE_FLAG);
+			for (i=0; i<FIFO_COUNT; i++) {
+				/* enable interrupts from all fifos */
+				FPGA_SETBITS(&fpga->fifo[i].ctrl, FIFO_IE);
+			}
+
+			while (1) {
+				/* wait loop */
+				while (!got_fifoirq) {
+					count++;
+					if (!(count % 100)) {
+						count2++;
+						putc(0x08); /* backspace */
+						putc(str[count2 % 4]);
+					}
+
+					/* Abort if ctrl-c was pressed */
+					if ((abort = ctrlc())) {
+						puts("\nAbort\n");
+						break;
+					}
+					udelay(1000);
+				}
+				if (abort)
+					break;
+
+				/* simple fifo backend */
+				if (got_fifoirq) {
+					for (i=0; i<FIFO_COUNT; i++)
+						dump_fifo(fpga, i, &n);
+
+					got_fifoirq = 0;
+					/* unmask global fifo irq */
+					FPGA_OUT32(&fpga->hostctrl,
+						   HOSTCTRL_FIFOIE_GATE | HOSTCTRL_FIFOIE_FLAG);
+				}
+			}
+
+			/* disable all fifo interrupts */
+			FPGA_OUT32(&fpga->hostctrl, HOSTCTRL_FIFOIE_GATE);
+			for (i=0; i<FIFO_COUNT; i++)
+				FPGA_CLRBITS(&fpga->fifo[i].ctrl, FIFO_IE);
+
+			irq_free_handler(IRQ0_FPGA);
+
+		} else {
+			printf("Usage:\nfifo %s\n", cmdtp->help);
+			return 1;
+		}
+		break;
+
+	case 4:
+	case 5:
+		if (!strcmp(argv[1],"write")) {
+			/* get fifo number or fifo address */
+			f = simple_strtoul(argv[2], NULL, 16);
+
+			/* data paramter */
+			data = simple_strtoul(argv[3], NULL, 16);
+
+			/* get optional count parameter */
+			n = 1;
+			if (argc >= 5)
+				n = (int)simple_strtoul(argv[4], NULL, 10);
+
+			if (f < FIFO_COUNT) {
+				printf("writing %d x %08x to fifo %d\n",
+				       n, data, f);
+				for (i=0; i<n; i++)
+					FPGA_OUT32(&fpga->fifo[f].data, data);
+			} else {
+				printf("writing %d x %08x to fifo port at address %08x\n",
+				       n, data, f);
+				for (i=0; i<n; i++)
+					out32(f, data);
+			}
+		} else {
+			printf("Usage:\nfifo %s\n", cmdtp->help);
+			return 1;
+		}
+		break;
+
+	default:
+		printf("Usage:\nfifo %s\n", cmdtp->help);
+		return 1;
+	}
+	return 0;
+}
+U_BOOT_CMD(
+	fifo,	5,	1,	do_fifo,
+	"fifo    - Fifo module operations\n",
+	"wait\nfifo read\n"
+	"fifo write fifo(0..3) data [cnt=1]\n"
+	"fifo write address(>=4) data [cnt=1]\n"
+	"  - without arguments: print all fifo's status\n"
+	"  - with 'wait' argument: interrupt driven read from all fifos\n"
+	"  - with 'read' argument: read current contents from all fifos\n"
+	"  - with 'write' argument: write 'data' 'cnt' times to 'fifo' or 'address'\n"
+	);
+
+
+int do_setup_bootstrap_eeprom(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
+{
+	ulong sdsdp[5];
+	ulong delay;
+	int count=16;
+
+	if (argc < 2) {
+		printf("Usage:\nsbe %s\n", cmdtp->help);
+		return -1;
+	}
+
+	if (argc > 1) {
+		if (!strcmp(argv[1], "400")) {
+			/* PLB=133MHz, PLB/PCI=4 */
+			printf("Bootstrapping for 400MHz\n");
+			sdsdp[0]=0x8678624e;
+			sdsdp[1]=0x0947a030;
+			sdsdp[2]=0x40082350;
+			sdsdp[3]=0x0d050000;
+		} else if (!strcmp(argv[1], "533")) {
+                        /* PLB=133MHz, PLB/PCI=3 */
+			printf("Bootstrapping for 533MHz\n");
+			sdsdp[0]=0x87788252;
+			sdsdp[1]=0x095fa030;
+			sdsdp[2]=0x40082350;
+			sdsdp[3]=0x0d050000;
+		} else if (!strcmp(argv[1], "667")) {
+			/* PLB=133MHz, PLB/PCI=4 */
+			printf("Bootstrapping for 667MHz\n");
+			sdsdp[0]=0x8778a256;
+			sdsdp[1]=0x0947a030;
+			sdsdp[2]=0x40082350;
+			sdsdp[3]=0x0d050000;
+		} else if (!strcmp(argv[1], "test")) {
+			/* TODO: this will replace the 667 MHz config above.
+			 * But it needs some more testing on a real 667 MHz CPU.
+			 */
+			printf("Bootstrapping for test (667MHz PLB=133PLB PLB/PCI=3)\n");
+			sdsdp[0]=0x8778a256;
+			sdsdp[1]=0x095fa030;
+			sdsdp[2]=0x40082350;
+			sdsdp[3]=0x0d050000;
+		} else {
+			printf("Usage:\nsbe %s\n", cmdtp->help);
+			return -1;
+		}
+	}
+
+	if (argc > 2) {
+		sdsdp[4] = 0;
+		if (argv[2][0]=='1')
+			sdsdp[4]=0x19750100;
+		else if (argv[2][0]=='0')
+			sdsdp[4]=0x19750000;
+		if (sdsdp[4])
+			count += 4;
+	}
+
+	if (argc > 3) {
+		delay = simple_strtoul(argv[3], NULL, 10);
+		if (delay > 20)
+			delay = 20;
+		sdsdp[4] |= delay;
+	}
+
+	printf("Writing boot EEPROM ...\n");
+	if (bootstrap_eeprom_write(CFG_I2C_BOOT_EEPROM_ADDR,
+				   0, (uchar*)sdsdp, count) != 0)
+		printf("bootstrap_eeprom_write failed\n");
+	else
+		printf("done (dump via 'i2c md 52 0.1 14')\n");
+
+	return 0;
+}
+U_BOOT_CMD(
+	sbe, 4, 0, do_setup_bootstrap_eeprom,
+	"sbe     - setup bootstrap eeprom\n",
+	"<cpufreq:400|533|667> [<console-uart:0|1> [<bringup delay (0..20s)>]]"
+	);
+
+
+#ifdef CONFIG_PRAM
+#include <environment.h>
+extern env_t *env_ptr;
+
+int do_painit(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
+{
+	DECLARE_GLOBAL_DATA_PTR;
+	u32 memsize;
+	u32 pram;
+	char *v;
+	u32 param;
+	ulong *lptr;
+
+	memsize = gd->bd->bi_memsize;
+
+	v = getenv("pram");
+	if (v)
+		pram = simple_strtoul(v, NULL, 10);
+	else {
+		printf("Error: pram undefined. Please define pram in KiB\n");
+		return 1;
+	}
+
+	param = memsize - (pram << 10);
+	printf("PARAM: @%08x\n", param);
+
+	memset((void*)param, 0, (pram << 10));
+	memcpy((void*)param, env_ptr, CFG_ENV_SIZE);
+
+	lptr = (ulong*)memsize;
+	*(--lptr) = CFG_ENV_SIZE;
+	*(--lptr) = pram << 10;
+	*(--lptr) = crc32(0, (void*)(memsize - 0x08), 0x08);
+	*(--lptr) = 0;
+	return 0;
+}
+U_BOOT_CMD(
+	painit,	1,	1,	do_painit,
+	"painit  - prepare PciAccess system\n",
+	NULL
+	);
+#endif /* CONFIG_PRAM */
+
+
+int do_selfreset(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
+{
+	if (argc > 1) {
+		if (argv[1][0] == '0') {
+			/* assert */
+			printf("self-reset# asserted\n");
+			out_be32((void*)GPIO0_TCR,
+				 in_be32((void*)GPIO0_TCR) | GPIO0_SELF_RST);
+		} else {
+			/* deassert */
+			printf("self-reset# deasserted\n");
+			out_be32((void*)GPIO0_TCR,
+				 in_be32((void*)GPIO0_TCR) & ~GPIO0_SELF_RST);
+		}
+	} else {
+		printf("self-reset# is %s\n",
+		       in_be32((void*)GPIO0_TCR) & GPIO0_SELF_RST ?
+		       "active" : "inactive");
+	}
+
+	return 0;
+}
+U_BOOT_CMD(
+	selfreset,	2,	1,	do_selfreset,
+	"selfreset- assert self-reset# signal\n",
+	NULL
+	);
+
+
+int do_resetout(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
+{
+	pmc440_fpga_t *fpga = (pmc440_fpga_t *)FPGA_BA;
+
+	/* requiers bootet FPGA and PLD_IOEN_N active */
+	if (in_be32((void*)GPIO1_OR) & GPIO1_IOEN_N) {
+		printf("Error: resetout requires a bootet FPGA\n");
+		return -1;
+	}
+
+	if (argc > 1) {
+		if (argv[1][0] == '0') {
+			/* assert */
+			printf("PMC-RESETOUT# asserted\n");
+			FPGA_OUT32(&fpga->hostctrl,
+				   HOSTCTRL_PMCRSTOUT_GATE);
+		} else {
+			/* deassert */
+			printf("PMC-RESETOUT# deasserted\n");
+			FPGA_OUT32(&fpga->hostctrl,
+				   HOSTCTRL_PMCRSTOUT_GATE | HOSTCTRL_PMCRSTOUT_FLAG);
+		}
+	} else {
+		printf("PMC-RESETOUT# is %s\n",
+		       FPGA_IN32(&fpga->hostctrl) & HOSTCTRL_PMCRSTOUT_FLAG ?
+		       "inactive" : "active");
+	}
+
+	return 0;
+}
+U_BOOT_CMD(
+	resetout,	2,	1,	do_resetout,
+	"resetout - assert PMC-RESETOUT# signal\n",
+	NULL
+	);
+
+
+int do_inta(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
+{
+	if (is_monarch()) {
+		printf("This command is only supported in non-monarch mode\n");
+		return -1;
+	}
+
+	if (argc > 1) {
+		if (argv[1][0] == '0') {
+			/* assert */
+			printf("inta# asserted\n");
+			out_be32((void*)GPIO1_TCR,
+				 in_be32((void*)GPIO1_TCR) | GPIO1_INTA_FAKE);
+		} else {
+			/* deassert */
+			printf("inta# deasserted\n");
+			out_be32((void*)GPIO1_TCR,
+				 in_be32((void*)GPIO1_TCR) & ~GPIO1_INTA_FAKE);
+		}
+	} else {
+		printf("inta# is %s\n", in_be32((void*)GPIO1_TCR) & GPIO1_INTA_FAKE ? "active" : "inactive");
+	}
+	return 0;
+}
+U_BOOT_CMD(
+	inta,	2,	1,	do_inta,
+	"inta    - Assert/Deassert or query INTA# state in non-monarch mode\n",
+	NULL
+	);
+
+
+/* test-only */
+int do_pmm(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
+{
+	ulong pciaddr;
+
+	if (argc > 1) {
+		pciaddr = simple_strtoul(argv[1], NULL, 16);
+
+		pciaddr &= 0xf0000000;
+
+		/* map PCI address at 0xc0000000 in PLB space */
+		out32r(PCIX0_PMM1MA, 0x00000000); /* PMM1 Mask/Attribute - disabled b4 setting */
+		out32r(PCIX0_PMM1LA, 0xc0000000); /* PMM1 Local Address */
+		out32r(PCIX0_PMM1PCILA, pciaddr); /* PMM1 PCI Low Address */
+		out32r(PCIX0_PMM1PCIHA, 0x00000000); /* PMM1 PCI High Address */
+		out32r(PCIX0_PMM1MA, 0xf0000001); /* 256MB + No prefetching, and enable region */
+	} else {
+		printf("Usage:\npmm %s\n", cmdtp->help);
+	}
+	return 0;
+}
+U_BOOT_CMD(
+	pmm,	2,	1,	do_pmm,
+	"pmm     - Setup pmm[1] registers\n",
+	"<pciaddr> (pciaddr will be aligned to 256MB)\n"
+	);
+
+#if defined(CFG_EEPROM_WREN)
+int do_eep_wren(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
+{
+	int query = argc == 1;
+	int state = 0;
+
+	if (query) {
+		/* Query write access state. */
+		state = eeprom_write_enable(CFG_I2C_EEPROM_ADDR, -1);
+		if (state < 0) {
+			puts("Query of write access state failed.\n");
+		} else {
+			printf("Write access for device 0x%0x is %sabled.\n",
+			       CFG_I2C_EEPROM_ADDR, state ? "en" : "dis");
+			state = 0;
+		}
+	} else {
+		if ('0' == argv[1][0]) {
+			/* Disable write access. */
+			state = eeprom_write_enable(CFG_I2C_EEPROM_ADDR, 0);
+		} else {
+			/* Enable write access. */
+			state = eeprom_write_enable(CFG_I2C_EEPROM_ADDR, 1);
+		}
+		if (state < 0) {
+			puts("Setup of write access state failed.\n");
+		}
+	}
+
+	return state;
+}
+U_BOOT_CMD(eepwren, 2, 0, do_eep_wren,
+	   "eepwren - Enable / disable / query EEPROM write access\n",
+	   NULL);
+#endif /* #if defined(CFG_EEPROM_WREN) */
+
+#endif /* CONFIG_CMD_BSP */

463 lines not on this page · raw message

similarity index 71%
copy from board/gen860t/fpga.h
copy to board/esd/pmc440/fpga.h
index 01967a4..2745d8f 100644
@@ -1,7 +1,6 @@
 /*
- * (C) Copyright 2002
- * Rich Ireland, Enterasys Networks, rireland at enterasys.com.
- * Keith Outwater, keith_outwater at mvis.com.
+ * (C) Copyright 2007
+ * Matthias Fuchs, esd gmbh germany, matthias.fuchs at esd-electronics.com
  *
  * See file CREDITS for list of people who contributed to this
  * project.

@@ -20,14 +19,10 @@
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
  * MA 02111-1307 USA
- *
  */
 
-/*
- * Virtex2 FPGA configuration support for the GEN860T computer
- */
+extern int pmc440_init_fpga(void);
 
-extern int gen860t_init_fpga(void);
 extern int fpga_pgm_fn(int assert_pgm, int flush, int cookie);
 extern int fpga_init_fn(int cookie);
 extern int fpga_err_fn(int cookie);

@@ -35,6 +30,7 @@ extern int fpga_done_fn(int cookie);
 extern int fpga_clk_fn(int assert_clk, int flush, int cookie);
 extern int fpga_cs_fn(int assert_cs, int flush, int cookie);
 extern int fpga_wr_fn(int assert_write, int flush, int cookie);
+extern int fpga_wdata_fn (uchar data, int flush, int cookie);
 extern int fpga_read_data_fn(unsigned char *data, int cookie);
 extern int fpga_write_data_fn(unsigned char data, int flush, int cookie);
 extern int fpga_busy_fn(int cookie);

@@ -42,4 +38,12 @@ extern int fpga_abort_fn(int cookie );
 extern int fpga_pre_config_fn(int cookie );
 extern int fpga_post_config_fn(int cookie );
 
-/* vim: set ts=4 sw=4 tw=78: */
+extern int ngcc_fpga_pgm_fn(int assert_pgm, int flush, int cookie);
+extern int ngcc_fpga_init_fn(int cookie);
+extern int ngcc_fpga_done_fn(int cookie);
+extern int ngcc_fpga_clk_fn(int assert_clk, int flush, int cookie);
+extern int ngcc_fpga_wr_fn(int assert_write, int flush, int cookie);
+extern int ngcc_fpga_pre_config_fn(int cookie );
+extern int ngcc_fpga_post_config_fn(int cookie );
+
+

new file mode 100644
index 0000000..0480ece
@@ -0,0 +1,555 @@
+/*
+ * (C) Copyright 2007
+ * Matthias Fuchs, esd Gmbh, matthias.fuchs at esd-electronics.com.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ */
+
+#include <common.h>
+#include <command.h>
+#include <asm/io.h>
+
+#include <asm/processor.h>
+
+#include "pmc440.h"
+
+int is_monarch(void);
+int bootstrap_eeprom_write(unsigned dev_addr, unsigned offset, uchar *buffer, unsigned cnt);
+int eeprom_write_enable(unsigned dev_addr, int state);
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#ifdef CONFIG_CMD_BSP
+
+static int got_fifoirq;
+static int got_hcirq;
+
+int fpga_interrupt(u32 arg)
+{
+	pmc440_fpga_t *fpga = (pmc440_fpga_t *)arg;
+	int rc = -1; /* not for us */
+	u32 status = FPGA_IN32(&fpga->status);
+
+	/* check for interrupt from fifo module */
+	if (status & STATUS_FIFO_ISF) {
+		/* disable this int source */
+		FPGA_OUT32(&fpga->hostctrl, HOSTCTRL_FIFOIE_GATE);
+		rc = 0;
+		got_fifoirq = 1; /* trigger backend */
+	}
+
+	if (status & STATUS_HOST_ISF) {
+		FPGA_OUT32(&fpga->hostctrl, HOSTCTRL_HCINT_GATE);
+		rc = 0;
+		got_hcirq = 1;
+	}
+
+	return rc;
+}
+
+
+int do_waithci(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
+{
+	pmc440_fpga_t *fpga = (pmc440_fpga_t *)FPGA_BA;
+
+	got_hcirq = 0;
+
+	FPGA_CLRBITS(&fpga->ctrla, CTRL_HOST_IE);
+	FPGA_OUT32(&fpga->hostctrl, HOSTCTRL_HCINT_GATE);
+
+	irq_install_handler(IRQ0_FPGA,
+			    (interrupt_handler_t *)fpga_interrupt,
+			    fpga);
+
+	FPGA_SETBITS(&fpga->ctrla, CTRL_HOST_IE);
+
+	while (!got_hcirq) {
+		/* Abort if ctrl-c was pressed */
+		if (ctrlc()) {
+			puts("\nAbort\n");
+			break;
+		}
+	}
+	if (got_hcirq)
+		printf("Got interrupt!\n");
+
+	FPGA_CLRBITS(&fpga->ctrla, CTRL_HOST_IE);
+	irq_free_handler(IRQ0_FPGA);
+	return 0;
+}
+U_BOOT_CMD(
+	waithci,	1,	1,	do_waithci,
+	"waithci - Wait for host control interrupt\n",
+	NULL
+	);
+
+
+void dump_fifo(pmc440_fpga_t *fpga, int f, int *n)
+{
+	u32 ctrl;
+
+	while (!((ctrl = FPGA_IN32(&fpga->fifo[f].ctrl)) & FIFO_EMPTY)) {
+		printf("%5d  %d    %3d  %08x",
+		       (*n)++, f, ctrl & (FIFO_LEVEL_MASK | FIFO_FULL),
+		       FPGA_IN32(&fpga->fifo[f].data));
+		if (ctrl & FIFO_OVERFLOW) {
+			printf(" OVERFLOW\n");
+			FPGA_CLRBITS(&fpga->fifo[f].ctrl, FIFO_OVERFLOW);
+		} else
+			printf("\n");
+	}
+}
+
+
+int do_fifo(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
+{
+	pmc440_fpga_t *fpga = (pmc440_fpga_t *)FPGA_BA;
+	int i;
+	int n = 0;
+	u32 ctrl, data, f;
+	char str[] = "\\|/-";
+	int abort = 0;
+	int count = 0;
+	int count2 = 0;
+
+	switch (argc) {
+	case 1:
+		/* print all fifos status information */
+		printf("fifo level status\n");
+		printf("______________________________\n");
+		for (i=0; i<FIFO_COUNT; i++) {
+			ctrl = FPGA_IN32(&fpga->fifo[i].ctrl);
+			printf(" %d    %3d  %s%s%s %s\n",
+			       i, ctrl & (FIFO_LEVEL_MASK | FIFO_FULL),
+			       ctrl & FIFO_FULL ? "FULL     " : "",
+			       ctrl & FIFO_EMPTY ? "EMPTY    " : "",
+			       ctrl & (FIFO_FULL|FIFO_EMPTY) ? "" : "NOT EMPTY",
+			       ctrl & FIFO_OVERFLOW ? "OVERFLOW" : "");
+		}
+		break;
+
+	case 2:
+		/* completely read out fifo 'n' */
+		if (!strcmp(argv[1],"read")) {
+			printf("  #   fifo level data\n");
+			printf("______________________________\n");
+
+			for (i=0; i<FIFO_COUNT; i++)
+				dump_fifo(fpga, i, &n);
+
+		} else if (!strcmp(argv[1],"wait")) {
+			got_fifoirq = 0;
+
+			irq_install_handler(IRQ0_FPGA,
+					    (interrupt_handler_t *)fpga_interrupt,
+					    fpga);
+
+			printf("  #   fifo level data\n");
+			printf("______________________________\n");
+
+			/* enable all fifo interrupts */
+			FPGA_OUT32(&fpga->hostctrl,
+				   HOSTCTRL_FIFOIE_GATE | HOSTCTRL_FIFOIE_FLAG);
+			for (i=0; i<FIFO_COUNT; i++) {
+				/* enable interrupts from all fifos */
+				FPGA_SETBITS(&fpga->fifo[i].ctrl, FIFO_IE);
+			}
+
+			while (1) {
+				/* wait loop */
+				while (!got_fifoirq) {
+					count++;
+					if (!(count % 100)) {
+						count2++;
+						putc(0x08); /* backspace */
+						putc(str[count2 % 4]);
+					}
+
+					/* Abort if ctrl-c was pressed */
+					if ((abort = ctrlc())) {
+						puts("\nAbort\n");
+						break;
+					}
+					udelay(1000);
+				}
+				if (abort)
+					break;
+
+				/* simple fifo backend */
+				if (got_fifoirq) {
+					for (i=0; i<FIFO_COUNT; i++)
+						dump_fifo(fpga, i, &n);
+
+					got_fifoirq = 0;
+					/* unmask global fifo irq */
+					FPGA_OUT32(&fpga->hostctrl,
+						   HOSTCTRL_FIFOIE_GATE | HOSTCTRL_FIFOIE_FLAG);
+				}
+			}
+
+			/* disable all fifo interrupts */
+			FPGA_OUT32(&fpga->hostctrl, HOSTCTRL_FIFOIE_GATE);
+			for (i=0; i<FIFO_COUNT; i++)
+				FPGA_CLRBITS(&fpga->fifo[i].ctrl, FIFO_IE);
+
+			irq_free_handler(IRQ0_FPGA);
+
+		} else {
+			printf("Usage:\nfifo %s\n", cmdtp->help);
+			return 1;
+		}
+		break;
+
+	case 4:
+	case 5:
+		if (!strcmp(argv[1],"write")) {
+			/* get fifo number or fifo address */
+			f = simple_strtoul(argv[2], NULL, 16);
+
+			/* data paramter */
+			data = simple_strtoul(argv[3], NULL, 16);
+
+			/* get optional count parameter */
+			n = 1;
+			if (argc >= 5)
+				n = (int)simple_strtoul(argv[4], NULL, 10);
+
+			if (f < FIFO_COUNT) {
+				printf("writing %d x %08x to fifo %d\n",
+				       n, data, f);
+				for (i=0; i<n; i++)
+					FPGA_OUT32(&fpga->fifo[f].data, data);
+			} else {
+				printf("writing %d x %08x to fifo port at address %08x\n",
+				       n, data, f);
+				for (i=0; i<n; i++)
+					out32(f, data);
+			}
+		} else {
+			printf("Usage:\nfifo %s\n", cmdtp->help);
+			return 1;
+		}
+		break;
+
+	default:
+		printf("Usage:\nfifo %s\n", cmdtp->help);
+		return 1;
+	}
+	return 0;
+}
+U_BOOT_CMD(
+	fifo,	5,	1,	do_fifo,
+	"fifo    - Fifo module operations\n",
+	"wait\nfifo read\n"
+	"fifo write fifo(0..3) data [cnt=1]\n"
+	"fifo write address(>=4) data [cnt=1]\n"
+	"  - without arguments: print all fifo's status\n"
+	"  - with 'wait' argument: interrupt driven read from all fifos\n"
+	"  - with 'read' argument: read current contents from all fifos\n"
+	"  - with 'write' argument: write 'data' 'cnt' times to 'fifo' or 'address'\n"
+	);
+
+
+int do_setup_bootstrap_eeprom(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
+{
+	ulong sdsdp[5];
+	ulong delay;
+	int count=16;
+
+	if (argc < 2) {
+		printf("Usage:\nsbe %s\n", cmdtp->help);
+		return -1;
+	}
+
+	if (argc > 1) {
+		if (!strcmp(argv[1], "400")) {
+			/* PLB=133MHz, PLB/PCI=4 */
+			printf("Bootstrapping for 400MHz\n");
+			sdsdp[0]=0x8678624e;
+			sdsdp[1]=0x0947a030;
+			sdsdp[2]=0x40082350;
+			sdsdp[3]=0x0d050000;
+		} else if (!strcmp(argv[1], "533")) {
+			/* PLB=133MHz, PLB/PCI=3 */
+			printf("Bootstrapping for 533MHz\n");
+			sdsdp[0]=0x87788252;
+			sdsdp[1]=0x095fa030;
+			sdsdp[2]=0x40082350;
+			sdsdp[3]=0x0d050000;
+		} else if (!strcmp(argv[1], "667")) {
+			/* PLB=133MHz, PLB/PCI=4 */
+			printf("Bootstrapping for 667MHz\n");
+			sdsdp[0]=0x8778a256;
+			sdsdp[1]=0x0947a030;
+			sdsdp[2]=0x40082350;
+			sdsdp[3]=0x0d050000;
+		} else if (!strcmp(argv[1], "test")) {
+			/* TODO: this will replace the 667 MHz config above.
+			 * But it needs some more testing on a real 667 MHz CPU.
+			 */
+			printf("Bootstrapping for test (667MHz PLB=133PLB PLB/PCI=3)\n");
+			sdsdp[0]=0x8778a256;
+			sdsdp[1]=0x095fa030;
+			sdsdp[2]=0x40082350;
+			sdsdp[3]=0x0d050000;
+		} else {
+			printf("Usage:\nsbe %s\n", cmdtp->help);
+			return -1;
+		}
+	}
+
+	if (argc > 2) {
+		sdsdp[4] = 0;
+		if (argv[2][0]=='1')
+			sdsdp[4]=0x19750100;
+		else if (argv[2][0]=='0')
+			sdsdp[4]=0x19750000;
+		if (sdsdp[4])
+			count += 4;
+	}
+
+	if (argc > 3) {
+		delay = simple_strtoul(argv[3], NULL, 10);
+		if (delay > 20)
+			delay = 20;
+		sdsdp[4] |= delay;
+	}
+
+	printf("Writing boot EEPROM ...\n");
+	if (bootstrap_eeprom_write(CFG_I2C_BOOT_EEPROM_ADDR,
+				   0, (uchar*)sdsdp, count) != 0)
+		printf("bootstrap_eeprom_write failed\n");
+	else
+		printf("done (dump via 'i2c md 52 0.1 14')\n");
+
+	return 0;
+}
+U_BOOT_CMD(
+	sbe, 4, 0, do_setup_bootstrap_eeprom,
+	"sbe     - setup bootstrap eeprom\n",
+	"<cpufreq:400|533|667> [<console-uart:0|1> [<bringup delay (0..20s)>]]"
+	);
+
+
+#ifdef CONFIG_PRAM
+#include <environment.h>
+extern env_t *env_ptr;
+
+int do_painit(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
+{
+	DECLARE_GLOBAL_DATA_PTR;
+	u32 memsize;
+	u32 pram;
+	char *v;
+	u32 param;
+	ulong *lptr;
+
+	memsize = gd->bd->bi_memsize;
+
+	v = getenv("pram");
+	if (v)
+		pram = simple_strtoul(v, NULL, 10);
+	else {
+		printf("Error: pram undefined. Please define pram in KiB\n");
+		return 1;
+	}
+
+	param = memsize - (pram << 10);
+	printf("PARAM: @%08x\n", param);
+
+	memset((void*)param, 0, (pram << 10));
+	memcpy((void*)param, env_ptr, CFG_ENV_SIZE);
+
+	lptr = (ulong*)memsize;
+	*(--lptr) = CFG_ENV_SIZE;
+	*(--lptr) = pram << 10;
+	*(--lptr) = crc32(0, (void*)(memsize - 0x08), 0x08);
+	*(--lptr) = 0;
+	return 0;
+}
+U_BOOT_CMD(
+	painit,	1,	1,	do_painit,
+	"painit  - prepare PciAccess system\n",
+	NULL
+	);
+#endif /* CONFIG_PRAM */
+
+
+int do_selfreset(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
+{
+	if (argc > 1) {
+		if (argv[1][0] == '0') {
+			/* assert */
+			printf("self-reset# asserted\n");
+			out_be32((void*)GPIO0_TCR,
+				 in_be32((void*)GPIO0_TCR) | GPIO0_SELF_RST);
+		} else {
+			/* deassert */
+			printf("self-reset# deasserted\n");
+			out_be32((void*)GPIO0_TCR,
+				 in_be32((void*)GPIO0_TCR) & ~GPIO0_SELF_RST);
+		}
+	} else {
+		printf("self-reset# is %s\n",
+		       in_be32((void*)GPIO0_TCR) & GPIO0_SELF_RST ?
+		       "active" : "inactive");
+	}
+
+	return 0;
+}
+U_BOOT_CMD(
+	selfreset,	2,	1,	do_selfreset,
+	"selfreset- assert self-reset# signal\n",
+	NULL
+	);
+
+
+int do_resetout(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
+{
+	pmc440_fpga_t *fpga = (pmc440_fpga_t *)FPGA_BA;
+
+	/* requiers bootet FPGA and PLD_IOEN_N active */
+	if (in_be32((void*)GPIO1_OR) & GPIO1_IOEN_N) {
+		printf("Error: resetout requires a bootet FPGA\n");
+		return -1;
+	}
+
+	if (argc > 1) {
+		if (argv[1][0] == '0') {
+			/* assert */
+			printf("PMC-RESETOUT# asserted\n");
+			FPGA_OUT32(&fpga->hostctrl,
+				   HOSTCTRL_PMCRSTOUT_GATE);
+		} else {
+			/* deassert */
+			printf("PMC-RESETOUT# deasserted\n");
+			FPGA_OUT32(&fpga->hostctrl,
+				   HOSTCTRL_PMCRSTOUT_GATE | HOSTCTRL_PMCRSTOUT_FLAG);
+		}
+	} else {
+		printf("PMC-RESETOUT# is %s\n",
+		       FPGA_IN32(&fpga->hostctrl) & HOSTCTRL_PMCRSTOUT_FLAG ?
+		       "inactive" : "active");
+	}
+
+	return 0;
+}
+U_BOOT_CMD(
+	resetout,	2,	1,	do_resetout,
+	"resetout - assert PMC-RESETOUT# signal\n",
+	NULL
+	);
+
+
+int do_inta(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
+{
+	if (is_monarch()) {
+		printf("This command is only supported in non-monarch mode\n");
+		return -1;
+	}
+
+	if (argc > 1) {
+		if (argv[1][0] == '0') {
+			/* assert */
+			printf("inta# asserted\n");
+			out_be32((void*)GPIO1_TCR,
+				 in_be32((void*)GPIO1_TCR) | GPIO1_INTA_FAKE);
+		} else {
+			/* deassert */
+			printf("inta# deasserted\n");
+			out_be32((void*)GPIO1_TCR,
+				 in_be32((void*)GPIO1_TCR) & ~GPIO1_INTA_FAKE);
+		}
+	} else {
+		printf("inta# is %s\n", in_be32((void*)GPIO1_TCR) & GPIO1_INTA_FAKE ? "active" : "inactive");
+	}
+	return 0;
+}
+U_BOOT_CMD(
+	inta,	2,	1,	do_inta,
+	"inta    - Assert/Deassert or query INTA# state in non-monarch mode\n",
+	NULL
+	);
+
+
+/* test-only */
+int do_pmm(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
+{
+	ulong pciaddr;
+
+	if (argc > 1) {
+		pciaddr = simple_strtoul(argv[1], NULL, 16);
+
+		pciaddr &= 0xf0000000;
+
+		/* map PCI address at 0xc0000000 in PLB space */
+		out32r(PCIX0_PMM1MA, 0x00000000); /* PMM1 Mask/Attribute - disabled b4 setting */
+		out32r(PCIX0_PMM1LA, 0xc0000000); /* PMM1 Local Address */
+		out32r(PCIX0_PMM1PCILA, pciaddr); /* PMM1 PCI Low Address */
+		out32r(PCIX0_PMM1PCIHA, 0x00000000); /* PMM1 PCI High Address */
+		out32r(PCIX0_PMM1MA, 0xf0000001); /* 256MB + No prefetching, and enable region */
+	} else {
+		printf("Usage:\npmm %s\n", cmdtp->help);
+	}
+	return 0;
+}
+U_BOOT_CMD(
+	pmm,	2,	1,	do_pmm,
+	"pmm     - Setup pmm[1] registers\n",
+	"<pciaddr> (pciaddr will be aligned to 256MB)\n"
+	);
+
+#if defined(CFG_EEPROM_WREN)
+int do_eep_wren(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
+{
+	int query = argc == 1;
+	int state = 0;
+
+	if (query) {
+		/* Query write access state. */
+		state = eeprom_write_enable(CFG_I2C_EEPROM_ADDR, -1);
+		if (state < 0) {
+			puts("Query of write access state failed.\n");
+		} else {
+			printf("Write access for device 0x%0x is %sabled.\n",
+			       CFG_I2C_EEPROM_ADDR, state ? "en" : "dis");
+			state = 0;
+		}
+	} else {
+		if ('0' == argv[1][0]) {
+			/* Disable write access. */
+			state = eeprom_write_enable(CFG_I2C_EEPROM_ADDR, 0);
+		} else {
+			/* Enable write access. */
+			state = eeprom_write_enable(CFG_I2C_EEPROM_ADDR, 1);
+		}
+		if (state < 0) {
+			puts("Setup of write access state failed.\n");
+		}
+	}
+
+	return state;
+}
+U_BOOT_CMD(eepwren, 2, 0, do_eep_wren,
+	   "eepwren - Enable / disable / query EEPROM write access\n",
+	   NULL);
+#endif /* #if defined(CFG_EEPROM_WREN) */
+
+#endif /* CONFIG_CMD_BSP */

469 lines not on this page · raw message

47 lines not on this page · raw message

626 lines not on this page · raw message