Loopback mounting jffs2 under UML?
Subsystems (2)
I want to loopback mount a jffs2 filesystem, and this filesystem has incestuous knowledge of flash devices for wear levelling and stuff, so it will only mount an actual flash device and not a normal block device.
There's a way to make a loopback device look like a flash device, letting you loopback mount jffs2, but it involves recompiling the kerenel to add support for it, and of course I went "User Mode Linux"... Except that UML disables the flash menu entirely.
Basically, I need to be able to enable MTD_BLOCK so I can go:
losetup /dev/loop0 /path/to/imagefile.jffs2
insmod blkmtd erasesz=256 device=/dev/loop0
mount -t jffs2 /dev/mtdblock0 /mnt
This shouldn't need any actual flash hardware. It's just layering another translation layer on top of loopback.
Suggestions?
Rob
Signature · 13 lines
"One of my most productive days was throwing away 1000 lines of code." - Ken Thompson. ------------------------------------------------------------------------- SF.Net email is sponsored by: Check out the new SourceForge.net Marketplace. It's the best place to buy or sell services for just about anything Open Source. http://ad.doubleclick.net/clk;164216239;13503038;w?http://sf.net/marketplace _______________________________________________ User-mode-linux-devel mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/user-mode-linux-devel
Quoted 6 lines · Rob Landley
There's a way to make a loopback device look like a flash device, letting you loopback mount jffs2, but it involves recompiling the kerenel to add support for it, and of course I went "User Mode Linux"... Except that UML disables the flash menu entirely.
Suggestions?
I see this in menuconfig:
Symbol: MTD [=n]
Prompt: Memory Technology Device (MTD) support
Defined at drivers/mtd/Kconfig:3
Depends on: BROKEN && HAS_IOMEM
You could try removing the dependencies on BROKEN and HAS_IOMEM and see what happens...
Jeff
Signature · 12 lines
Work email - jdike at linux dot intel dot com ------------------------------------------------------------------------- SF.Net email is sponsored by: Check out the new SourceForge.net Marketplace. It's the best place to buy or sell services for just about anything Open Source. http://ad.doubleclick.net/clk;164216239;13503038;w?http://sf.net/marketplace _______________________________________________ User-mode-linux-devel mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/user-mode-linux-devel
Quoted 10 lines · On Tuesday 18 December 2007 13:29:11 Jeff Dike wrote:
Quoted 6 lines · Rob Landley
There's a way to make a loopback device look like a flash device, letting you loopback mount jffs2, but it involves recompiling the kerenel to add support for it, and of course I went "User Mode Linux"... Except that UML disables the flash menu entirely.
Suggestions?
I see this in menuconfig:
Quoted 7 lines
Symbol: MTD [=n]
Prompt: Memory Technology Device (MTD) support
Defined atdrivers/mtd/Kconfig:3
Depends on: BROKEN &&HAS_IOMEMYou could try removing the dependencies on BROKEN and
HAS_IOMEMand see what happens...
Actually, in -rc4 (what I have lying around), the depends is just on HAS_IOMEM, and the include in arch/um/Kconfig is guarded by "if BROKEN".
Building it, I hit the same darn error I've been patching my way around for months:
Quoted 10 lines
CC
arch/um/kernel/smp.o
In file included frominclude/asm/arch/tlb.h:9,
frominclude/asm/tlb.h:4,
fromarch/um/kernel/smp.c:8:include/asm-generic/tlb.h: In function ‘tlb_flush_mmu’:include/asm-generic/tlb.h:76: error: implicit declaration of function ‘release_pages’include/asm-generic/tlb.h: In function ‘tlb_remove_page’:include/asm-generic/tlb.h:105: error: implicit declaration of function ‘page_cache_release’ make[1]: *** [arch/um/kernel/smp.o] Error 1
make: *** [arch/um/kernel] Error 2
Patch that, and then it breaks with:
Quoted 6 lines
CC
drivers/mtd/chips/chipreg.o
In file included fromdrivers/mtd/chips/chipreg.c:13:include/linux/mtd/map.h: In function ‘inline_map_read’:include/linux/mtd/map.h:378: error: implicit declaration of function ‘__raw_readb’include/linux/mtd/map.h:380: error: implicit declaration of function ‘__raw_readw’include/linux/mtd/map.h:382: error: implicit
Quoted 8 lines
declaration of function ‘__raw_readl’
include/linux/mtd/map.h:385: error:
implicit declaration of function ‘__raw_readq’include/linux/mtd/map.h:388:
error: implicit declaration of function ‘memcpy_fromio’include/linux/mtd/map.h: In function ‘inline_map_write’:include/linux/mtd/map.h:406: error: implicit declaration of function ‘memcpy_toio’ make[3]: *** [drivers/mtd/chips/chipreg.o] Error 1 make[2]: *** [drivers/mtd/chips] Error 2
make[1]: *** [drivers/mtd] Error 2
All I enabled was CONFIG_MTD_BLOCK.
To reproduce what I did, yank these lines:
arch/um/Kconfig +0 -2
@@ -280,9 +280,7 @@ source "drivers/md/Kconfig" -if BROKEN source "drivers/mtd/Kconfig" -endif #This is just to shut up some Kconfig warnings, so no prompt. config INPUT
arch/um/kernel/smp.c +1 -0
@@ -5,6 +5,7 @@#include "linux/percpu.h" #include "asm/pgalloc.h" +#include "linux/pagemap.h" #include "asm/tlb.h" /* For some reason, mmu_gathers are referenced when CONFIG_SMP is off. */
drivers/mtd/Kconfig +0 -1
@@ -2,7 +2,6 @@ menuconfig MTD tristate "Memory Technology Device (MTD) support" - depends on HAS_IOMEM help Memory Technology Devices are flash, RAM and similar chips, often used for solid state file systems on embedded devices. This option
And then configure and build like so:
cat > mini.conf << EOFCONFIG_BINFMT_ELF=yCONFIG_HOSTFS=yCONFIG_BLK_DEV=yCONFIG_BLK_DEV_LOOP=y CONFIG_STDERR_CONSOLE=yCONFIG_UNIX98_PTYS=yCONFIG_EXT2_FS=yCONFIG_MTD=yCONFIG_MTD_BLOCK=y
EOF
make ARCH=um allnoconfig KCONFIG_ALLCONFIG=mini.conf make ARCH=um
Rob
Signature · 13 lines
"One of my most productive days was throwing away 1000 lines of code." - Ken Thompson. ------------------------------------------------------------------------- SF.Net email is sponsored by: Check out the new SourceForge.net Marketplace. It's the best place to buy or sell services for just about anything Open Source. http://ad.doubleclick.net/clk;164216239;13503038;w?http://sf.net/marketplace _______________________________________________ User-mode-linux-devel mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/user-mode-linux-devel
Quoted 7 lines · Rob Landley
Quoted 6 lines · On Tuesday 18 December 2007 13:29:11 Jeff Dike wrote:
Quoted 5 lines · Rob Landley
There's a way to make a loopback device look like a flash device, letting you loopback mount jffs2, but it involves recompiling the kerenel to add support for it, and of course I went "User Mode Linux"... Except that UML disables the flash menu entirely.
Quoted 22 lines
Quoted 5 lines
Quoted 1 line
Suggestions?
I see this in menuconfig:
Symbol: MTD [=n]
Actually, in -rc4 (what I have lying around), the depends is just on
HAS_IOMEM, and the include inarch/um/Kconfigis guarded by "if BROKEN".Quoted 14 lines
CC
drivers/mtd/chips/chipreg.o
In file included fromdrivers/mtd/chips/chipreg.c:13:include/linux/mtd/map.h: In function ‘inline_map_read’:include/linux/mtd/map.h:378: error: implicit declaration of function ‘__raw_readb’include/linux/mtd/map.h:380: error: implicit declaration of function ‘__raw_readw’include/linux/mtd/map.h:382: error: implicit declaration of function ‘__raw_readl’include/linux/mtd/map.h:385: error:
implicit declaration of function ‘__raw_readq’include/linux/mtd/map.h:388:
error: implicit declaration of function ‘memcpy_fromio’include/linux/mtd/map.h: In function ‘inline_map_write’:include/linux/mtd/map.h:406: error: implicit declaration of function ‘memcpy_toio’ make[3]: *** [drivers/mtd/chips/chipreg.o] Error 1 make[2]: *** [drivers/mtd/chips] Error 2
make[1]: *** [drivers/mtd] Error 2
Protect all static inline routines in <linux/mtd/map.h> that use readb() and friends by #ifdef CONFIG_HAS_IOMEM?
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- [email protected]
In personal conversations with technical people, I call myself a hacker. But when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
-------------------------------------------------------------------------
SF.Net email is sponsored by:
Check out the new SourceForge.net Marketplace.
It's the best place to buy or sell services
for just about anything Open Source.
http://ad.doubleclick.net/clk;164216239;13503038;w?http://sf.net/marketplace
_______________________________________________
User-mode-linux-devel mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/user-mode-linux-devel
I did try UML + blkmtd and jffs statically compiled in a couple of years ago and it then almost worked out of the box. It failed then for me due to a very small issue: the initializers in the different drivers initialized in the wrong order, so I got a panic due to a null-dereference. (driver initialization does/didn't have depencies).
Just me five cents :-)
Stian
Quoted 15 lines · Rob Landley
I want to loopback mount a jffs2 filesystem, and this filesystem has incestuous knowledge of flash devices for wear levelling and stuff, so it will only mount an actual flash device and not a normal block device.
There's a way to make a loopback device look like a flash device, letting you loopback mount jffs2, but it involves recompiling the kerenel to add support for it, and of course I went "User Mode Linux"... Except that UML disables the flash menu entirely.
Basically, I need to be able to enable
MTD_BLOCKso I can go:losetup
/dev/loop0/path/to/imagefile.jffs2
insmod blkmtd erasesz=256 device=/dev/loop0
mount -t jffs2/dev/mtdblock0/mnt
Quoted 6 lines
This shouldn't need any actual flash hardware. It's just layering another translation layer on top of loopback.
Suggestions?
Rob
-------------------------------------------------------------------------
SF.Net email is sponsored by:
Check out the new SourceForge.net Marketplace.
It's the best place to buy or sell services
for just about anything Open Source.
http://ad.doubleclick.net/clk;164216239;13503038;w?http://sf.net/marketplace
_______________________________________________
User-mode-linux-devel mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/user-mode-linux-devel