: move ColdFire timers.c to its own coldfire directory
PATCH 4/6 : move ColdFire timers.c to its own coldfire directory
Move common ColdFire CPU timers.c to common coldfire platform directory.
Currently the common ColdFire CPU family code sits in the arch/m68knommu/platform/5307 directory. This is confusing, the files containing this common code are in no way specific to the 5307 ColdFire. Create an arch/m68knommu/platform/coldfire directory to contain this common code. Other m68knommu CPU varients do not need use this code though, so it doesn't make sense to move it to arch/m68knommu/kernel.
Signed-off-by Greg Ungerer <[email protected]
arch/m68knommu/platform/5307/timers.c +0 -155
@@ -1,155 +0,0 @@ -/***************************************************************************/ - -/* -* timers.c -- generic ColdFire hardware timer support. -* -* Copyright (C) 1999-2007, Greg Ungerer ([email protected]) -*/ - -/***************************************************************************/ - -#include <linux/kernel.h> -#include <linux/init.h> -#include <linux/sched.h> -#include <linux/interrupt.h> -#include <linux/irq.h> -#include <asm/io.h> -#include <asm/traps.h> -#include <asm/machdep.h> -#include <asm/coldfire.h> -#include <asm/mcftimer.h> -#include <asm/mcfsim.h> - -/***************************************************************************/ - -/* -* By default use timer1 as the system clock timer. -*/ -#define TA (a) (MCF_MBAR + MCFTIMER_BASE1 + (a)) - -/* -* Default the timer and vector to use for ColdFire. Some ColdFire -* CPU's and some boards may want different. Their sub-architecture -* startup code (in config.c) can change these if they want. -*/ -unsigned int mcf_timervector =29 ; -unsigned int mcf_profilevector =31 ; -unsigned int mcf_timerlevel =5 ; - -/* -* These provide the underlying interrupt vector support. -* Unfortunately it is a little different on each ColdFire. -*/ -extern void mcf_settimericr (int timer,int level); -extern int mcf_timerirqpending (int timer); - -#if defined(CONFIG_M532x) -#define __raw_readtrr __raw_readl -#define __raw_writetrr __raw_writel -#else -#define __raw_readtrr __raw_readw -#define __raw_writetrr __raw_writew -#endif - -/***************************************************************************/ - -static irqreturn_t hw_tick (int irq,void *dummy) -{ -/* Reset the ColdFire timer */ -__raw_writeb (MCFTIMER_TER_CAP |MCFTIMER_TER_REF ,TA (MCFTIMER_TER )); - -return arch_timer_interrupt (irq, dummy); -} - -/***************************************************************************/ - -static struct irqaction coldfire_timer_irq = { - .name ="timer" , - .flags =IRQF_DISABLED |IRQF_TIMER , - .handler = hw_tick, -}; - -/***************************************************************************/ - -static int ticks_per_intr; - -void hw_timer_init (void ) -{ -setup_irq (mcf_timervector, &coldfire_timer_irq); - -__raw_writew (MCFTIMER_TMR_DISABLE ,TA (MCFTIMER_TMR )); - ticks_per_intr = (MCF_BUSCLK /16 ) /HZ ; -__raw_writetrr (ticks_per_intr -1 ,TA (MCFTIMER_TRR )); -__raw_writew (MCFTIMER_TMR_ENORI |MCFTIMER_TMR_CLK16 | -MCFTIMER_TMR_RESTART |MCFTIMER_TMR_ENABLE ,TA (MCFTIMER_TMR )); - -mcf_settimericr (1 , mcf_timerlevel); - -#ifdef CONFIG_HIGHPROFILE -coldfire_profile_init (); -#endif -} - -/***************************************************************************/ - -unsigned long hw_timer_offset (void ) -{ -unsigned long tcn, offset; - - tcn =__raw_readw (TA (MCFTIMER_TCN )); - offset = ((tcn +1 ) * (1000000 /HZ )) / ticks_per_intr; - -/* Check if we just wrapped the counters and maybe missed a tick */ -if ((offset < (1000000 /HZ /2 )) &&mcf_timerirqpending (1 )) - offset +=1000000 /HZ ; -return offset; -} - -/***************************************************************************/ -#ifdef CONFIG_HIGHPROFILE -/***************************************************************************/ - -/* -* By default use timer2 as the profiler clock timer. -*/ -#define PA (a) (MCF_MBAR + MCFTIMER_BASE2 + (a)) - -/* -* Choose a reasonably fast profile timer. Make it an odd value to -* try and get good coverage of kernel operations. -*/ -#define PROFILEHZ 1013 - -/* -* Use the other timer to provide high accuracy profiling info. -*/ -irqreturn_t coldfire_profile_tick (int irq,void *dummy) -{ -/* Reset ColdFire timer2 */ -__raw_writeb (MCFTIMER_TER_CAP |MCFTIMER_TER_REF ,PA (MCFTIMER_TER )); -if (current->pid) -profile_tick (CPU_PROFILING , regs); -return IRQ_HANDLED ; -} - -/***************************************************************************/ - -void coldfire_profile_init (void ) -{ -printk (KERN_INFO "PROFILE: lodging TIMER2 @ %dHz as profile timer\n" ,PROFILEHZ ); - -/* Set up TIMER 2 as high speed profile clock */ -__raw_writew (MCFTIMER_TMR_DISABLE ,PA (MCFTIMER_TMR )); - -__raw_writetrr (((MCF_CLK /16 ) /PROFILEHZ ),PA (MCFTIMER_TRR )); -__raw_writew (MCFTIMER_TMR_ENORI |MCFTIMER_TMR_CLK16 | -MCFTIMER_TMR_RESTART |MCFTIMER_TMR_ENABLE ,PA (MCFTIMER_TMR )); - -request_irq (mcf_profilevector, coldfire_profile_tick, - (IRQF_DISABLED |IRQ_FLG_FAST ),"profile timer" ,NULL ); -mcf_settimericr (2 ,7 ); -} - -/***************************************************************************/ -#endif /* CONFIG_HIGHPROFILE */ -/***************************************************************************/
arch/m68knommu/platform/coldfire/timers.c +155 -0
155 lines not on this page · raw message