LEDs: how to handle gpios that control brightness for all LEDs
Hi Richard,
I have a device that has various gpios that correspond to the colours (blue, red) of various LEDs. They only accept 0/1, not the actual brightness. However, there are two other gpios that can be used to control the brightness (of all LEDs): gpio V_LED 5V is bright, gpio V_LED 3.3V is dimmed and if neither of these two gpios are set, all LEDs stay off.
Can I simply export these brightness gpios to userland or would it be better to handle the brightness setting in the kernel so that setting e.g. 100 to a LED would automatically set the V_LED 3.3V gpio and 255 would set V_LED 5V. If so, how should this be done? If I can simply export them to userland, would mv2120:led:dimmed and mv2120:led:bright be appropriate names?
Second, the LEDS class sets all gpios to off by default. This is bad in my case because if neither of the brightness gpios (3.3V or 5V) are on, the SATA lights won't be shown either. Is there a way to specify in the platform code that one gpio should be turned on by default?
Thanks.
For the reference, here is my current work-in-progress patch (I use numbers rather than #defines for the gpio values because there's a table listing all gpios in the source file).
arch/arm/mach-orion5x/mv2120-setup.c +44 -0
@@ -137,6 +137,49 @@ static struct i2c_board_info __initdata mv2120_i2c_rtc = { .irq = 0, }; +static struct gpio_led mv2120_led_pins[] = { + { + .name ="mv2120:blue:sys" , + .gpio =0 , + }, + { + .name ="mv2120:red:sys" , + .gpio =1 , + }, + { + .name ="mv2120:led5v" , + .gpio =4 , + }, + { + .name ="mv2120:led3.3v" , + .gpio =5 , + }, + { + .name ="mv2120:red:sata0" , + .gpio =8 , + .active_low =1 , + }, + { + .name ="mv2120:red:sata1" , + .gpio =9 , + .active_low =1 , + }, + +}; + +static struct gpio_led_platform_data mv2120_led_data = { + .leds = mv2120_led_pins, + .num_leds =ARRAY_SIZE (mv2120_led_pins), +}; + +static struct platform_device mv2120_leds = { + .name ="leds-gpio" , + .id =-1 , + .dev = { + .platform_data = &mv2120_led_data, + } +}; +static void mv2120_power_off (void ) {pr_info ("%s: triggering power-off...\n" , __func__);
@@ -172,6 +215,7 @@ static void __init mv2120_init(void)gpio_free (MV2120_GPIO_RTC_IRQ ); }i2c_register_board_info (0 , &mv2120_i2c_rtc,1 ); +platform_device_register (&mv2120_leds);/* register mv2120 specific power-off method */ if (gpio_request(MV2120_GPIO_POWER_OFF, "POWEROFF") != 0 ||
Signature · 2 lines
Martin Michlmayr http://www.cyrius.com/
Quoted 11 lines · Martin Michlmayr
I have a device that has various gpios that correspond to the colours (blue, red) of various LEDs. They only accept 0/1, not the actual brightness. However, there are two other gpios that can be used to control the brightness (of all LEDs): gpio
V_LED5V is bright, gpioV_LED3.3V is dimmed and if neither of these two gpios are set, all LEDs stay off.Can I simply export these brightness gpios to userland or would it be better to handle the brightness setting in the kernel so that setting e.g. 100 to a LED would automatically set the
V_LED3.3V gpio and 255 would setV_LED5V. If so, how should this be done?
There is a enum led_brightness, which defines LED_HALF and LED_FULL. You would need a custom brightness function. Leds-gpio driver would need to be extended for it. The main problem with this approach is the unexpected effect for enduser, that adjusting brighntess of one led affects all of them.
Quoted 4 lines
Second, the LEDS class sets all gpios to off by default. This is bad in my case because if neither of the brightness gpios (3.3V or 5V) are on, the SATA lights won't be shown either. Is there a way to specify in the platform code that one gpio should be turned on by default?
default-on trigger is probably the easiest way.
Signature · 1 line
"rm -rf" only sounds scary if you don't have backups
Quoted 12 lines · Riku Voipio
Quoted 11 lines
I have a device that has various gpios that correspond to the colours (blue, red) of various LEDs. They only accept 0/1, not the actual brightness. However, there are two other gpios that can be used to control the brightness (of all LEDs): gpio
V_LED5V is bright, gpioV_LED3.3V is dimmed and if neither of these two gpios are set, all LEDs stay off.Can I simply export these brightness gpios to userland or would it be better to handle the brightness setting in the kernel so that setting e.g. 100 to a LED would automatically set the
V_LED3.3V gpio and 255 would setV_LED5V. If so, how should this be done?
Quoted 5 lines
There is a enum
led_brightness, which definesLED_HALFandLED_FULL. You would need a custom brightness function. Leds-gpio driver would need to be extended for it. The main problem with this approach is the unexpected effect for enduser, that adjusting brighntess of one led affects all of them.
OK, this sounds to me like I should simply export the gpios that influence the brightness.
Quoted 1 line
default-on trigger is probably the easiest way.
This works for me, thanks.
New patch below. Any comments Richard?
arch/arm/mach-orion5x/mv2120-setup.c +45 -0
@@ -137,6 +137,50 @@ static struct i2c_board_info __initdata mv2120_i2c_rtc = { .irq = 0, }; +static struct gpio_led mv2120_led_pins[] = { + { + .name ="mv2120:blue:health" , + .gpio =0 , + }, + { + .name ="mv2120:red:health" , + .gpio =1 , + }, + { + .name ="mv2120:led:bright" , + .gpio =4 , + .default_trigger ="default-on" , + }, + { + .name ="mv2120:led:dimmed" , + .gpio =5 , + }, + { + .name ="mv2120:red:sata0" , + .gpio =8 , + .active_low =1 , + }, + { + .name ="mv2120:red:sata1" , + .gpio =9 , + .active_low =1 , + }, + +}; + +static struct gpio_led_platform_data mv2120_led_data = { + .leds = mv2120_led_pins, + .num_leds =ARRAY_SIZE (mv2120_led_pins), +}; + +static struct platform_device mv2120_leds = { + .name ="leds-gpio" , + .id =-1 , + .dev = { + .platform_data = &mv2120_led_data, + } +}; +static void mv2120_power_off (void ) {pr_info ("%s: triggering power-off...\n" , __func__);
@@ -172,6 +216,7 @@ static void __init mv2120_init(void)gpio_free (MV2120_GPIO_RTC_IRQ ); }i2c_register_board_info (0 , &mv2120_i2c_rtc,1 ); +platform_device_register (&mv2120_leds);/* register mv2120 specific power-off method */ if (gpio_request(MV2120_GPIO_POWER_OFF, "POWEROFF") != 0 ||
Signature · 2 lines
Martin Michlmayr http://www.cyrius.com/