Compro E800F Hybrid D/A HW2 PCIe card

I have purchased a Compro E800F Hybrid D/A HW2 PCIe card. The chips on the card include:
Conexant PCIe A/V decoder: CX23885-132
Conexant MPEG II A/V/Encoder CX23417-11Z
Zarlink ZL10353 Demodulator
Xceiver XC3008ACQ Video Tuner
I have tried a number of solutions including building the latest copy of v4l-dvb and using the cx23885 module with card=4 option.
The problem I am having is that the lgdt330x module is being loaded with the cx23885, however my demodulator is the zarlink ZL10353. I am not sure on how to proceed. Please see below for output of lspci -vvnn.

03:00.0 Multimedia video controller [0400]: Conexant Unknown device [14f1:8852] (rev 02)
Subsystem: Compro Technology, Inc. Unknown device [185b:e800]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at fe800000 (64-bit, non-prefetchable) [size=2M]
Capabilities: [40] Express Endpoint IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 0
Link: Latency L0s <2us, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [90] Vital Product Data
Capabilities: [a0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000

Any help appreciated.

Thanks

_______________________________________________
linux-dvb mailing list
[email protected]
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb

I have now found that the E800 card is not
supported (http://www.linuxtv.org/wiki/index.php/DVB-T_PCIe_Cards). I am willing to test any code and have so far patched the v4l-dvb and the card semi-works...ie I can run the scan using local au-perth.conf file but I am unanle to sync.

FYI - I am runnign mythbuntu 8.04.

_______________________________________________
linux-dvb mailing list
[email protected]
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb