Skip to contentSkip to conversation

free tg3 ethernet driver

DISCUSSION Davi Leal 4 participants 7 messages Oct 8, 2008 – Oct 9, 2008

lore
Share & tools
lore

Davi Leal

author
#0 lore raw

We would like to have a tg3 driver which would be accepted as free by the FSF's standards.

At least some part of the driver seems to be GPL'ed; see [1]. However, the FSF's hardware guide lists tg3 as non-free, so there seems to be a non-free firmware somewhere.

[1]
http://www.broadcom.com/support/ethernet_nic/driver-sla.php?driver=570x-Linux

We would like to be able to use the free driver with Linux 2.6.27 or later.

Donation pledge group at
http://gnuherds.org/pledges?id=58
Current donations: $101 USD

#1 lore raw
Quoted 2 lines · On Wed, 8 Oct 2008 23:53:30 +0200 Davi Leal <[email protected]> wrote:

We would like to have a tg3 driver which would be accepted as free by the FSF's standards.

Well if you want to write new firmware for the device you'll need to reverse engineer the chip internals or convince Broadcom to document them for you. I suspect you'll have to get to the point of xraying the component slice by slice and need a multi-million dollar budget.

Alan

#6 lore raw
In reply to Davi Leal
Quoted 1 line · Davi Leal

We would like to have a tg3 driver which would be accepted as free by the FSF's standards.

I would like a pony.

Quoted 4 lines

At least some part of the driver seems to be GPL'ed; see [1]. However, the FSF's hardware guide lists tg3 as non-free, so there seems to be a non-free firmware somewhere.

[1]
http://www.broadcom.com/support/ethernet_nic/driver-sla.php?driver=570x-Linux

Firmware blobs aren't news. They've been discussed at great length on this list. If you want to whine about this, whine to Broadcom.

Quoted 1 line

We would like to be able to use the free driver with Linux 2.6.27 or later.

You must be new here.

Quoted 3 lines

Donation pledge group at
http://gnuherds.org/pledges?id=58
Current donations: $101 USD

Gigabit NICs with firmware-free drivers cost $10. If you care that much about the binary blob in tg3, maybe you should stop giving your money to Broadcom, and start giving it to vendors whose drivers satisfy your requirements.

-- Chris

author
#2 lore raw
In reply to Alan Cox
Quoted 4 lines · Alan Cox

Well if you want to write new firmware for the device you'll need to reverse engineer the chip internals or convince Broadcom to document them for you. I suspect you'll have to get to the point of xraying the component slice by slice and need a multi-million dollar budget.

People position seem to be continue to pledge to pay $151 to the developer(s) (even if it's Broadcom in case they apply to the pledge system) who provide a free driver for tg3 devices.

#3 lore raw
Quoted 9 lines · On Thu, 9 Oct 2008 22:36:57 +0200 Davi Leal <[email protected]> wrote:
Quoted 4 lines · Alan Cox

Well if you want to write new firmware for the device you'll need to reverse engineer the chip internals or convince Broadcom to document them for you. I suspect you'll have to get to the point of xraying the component slice by slice and need a multi-million dollar budget.

People position seem to be continue to pledge to pay $151 to the developer(s) (even if it's Broadcom in case they apply to the pledge system) who provide a free driver for tg3 devices.

Well thats good, another 1.999849 million dollars and you might get started.

With the best will in the world if you go and pay Broadcom zillions to open source the firmware the only incentive you create is for them to keep future firmware proprietary to sell to you next time around.

If on the other hand you buy non Broadcom equipment if you feel this way about the firmware then you create a far better economic incentive, and at $10 a NIC its not really hard to do that.

Alan

#4 lore raw
Quoted 13 lines · Alan Cox
Quoted 9 lines · On Thu, 9 Oct 2008 22:36:57 +0200 Davi Leal <[email protected]> wrote:
Quoted 4 lines · Alan Cox

Well if you want to write new firmware for the device you'll need to reverse engineer the chip internals or convince Broadcom to document them for you. I suspect you'll have to get to the point of xraying the component slice by slice and need a multi-million dollar budget.

People position seem to be continue to pledge to pay $151 to the developer(s) (even if it's Broadcom in case they apply to the pledge system) who provide a free driver for tg3 devices.

Quoted 6 lines

Well thats good, another 1.999849 million dollars and you might get started.

With the best will in the world if you go and pay Broadcom zillions to open source the firmware the only incentive you create is for them to keep future firmware proprietary to sell to you next time around.

Very true. If I start cooking awful cakes and I see people come to pay me for throwing them away, I'll sure restart ASAP.

Quoted 3 lines

If on the other hand you buy non Broadcom equipment if you feel this way about the firmware then you create a far better economic incentive, and at $10 a NIC its not really hard to do that.

And that's not counting with the fact that their crappy BNX2 has been showing horrible performance for several years now on servers, dropping frames like mad, and reminding the poor reliability and performance of Dlink's DL2000...

Willy

author
#5 lore raw
In reply to Alan Cox
Quoted 10 lines · Alan Cox

Well thats good, another 1.999849 million dollars and you might get started.

With the best will in the world if you go and pay Broadcom zillions to open source the firmware the only incentive you create is for them to keep future firmware proprietary to sell to you next time around.

If on the other hand you buy non Broadcom equipment if you feel this way about the firmware then you create a far better economic incentive, and at $10 a NIC its not really hard to do that.

We have added your new comments in the pledge description.

http://gnuherds.org/pledges?id=58