USB ehci pci initial support
cover USB ehci pci initial support
Add USB ehci pci support. This patch doesn't include any pci_ids and it is not tested on real hardware. To use it add (for example) the following in the board configuration file:
#define CONFIG_CMD_USB 1
#define CONFIG_USB_STORAGE 1
#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_PCI 1
#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 2
#define CONFIG_LEGACY_USB_INIT_SEQ 1
#define CONFIG_PCI_EHCI_DEVICE 1
--- drivers/usb/Makefile | 1 + drivers/usb/usb_ehci_pci.c | 64 ++++++++++++++++++++++++++++++++++++++++++++ 2 files changed, 65 insertions(+), 0 deletions(-) create mode 100644 drivers/usb/usb_ehci_pci.c
drivers/usb/Makefile +1 -0
@@ -35,6 +35,7 @@ COBJS-$(CONFIG_USB_ISP116X_HCD) += isp116x-hcd.o COBJS-$(CONFIG_USB_R8A66597_HCD) += r8a66597-hcd.o COBJS-$(CONFIG_USB_SL811HS) += sl811_usb.o COBJS-$(CONFIG_USB_EHCI_FSL) += usb_ehci_fsl.o +COBJS-$(CONFIG_USB_EHCI_PCI) += usb_ehci_pci.o # device ifdef CONFIG_USB_DEVICE
drivers/usb/usb_ehci_pci.c new file +64 -0
64 lines not on this page · raw message
Signature · 1 line
1.5.6.5
cover USB ehci pci initial support
Hello Michael,
2008/12/17 Michael Trimarchi <[email protected]>:
Quoted 11 lines
Add USB ehci pci support. This patch doesn't include any
pci_idsand it is not tested on real hardware. To use it add (for example) the following in the board configuration file:#define
CONFIG_CMD_USB1
#defineCONFIG_USB_STORAGE1
#defineCONFIG_USB_EHCI
#defineCONFIG_USB_EHCI_PCI1
#defineCONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS2
#defineCONFIG_LEGACY_USB_INIT_SEQ1
#defineCONFIG_PCI_EHCI_DEVICE1
I think that this kind of information should be put in the toplevel README file. A note where to put the PCI-ids is also nice.
Kind Regards,
Remy
Quoted 95 lines
Signed-off-by Michael Trimarchi <[email protected]>--- drivers/usb/Makefile | 1 + drivers/usb/usb_ehci_pci.c | 64 ++++++++++++++++++++++++++++++++++++++++++++ 2 files changed, 65 insertions(+), 0 deletions(-) create mode 100644 drivers/usb/usb_ehci_pci.cdrivers/usb/Makefile +1
-0@@ -35,6 +35,7 @@ COBJS-$(CONFIG_USB_ISP116X_HCD) += isp116x-hcd.o COBJS-$(CONFIG_USB_R8A66597_HCD) += r8a66597-hcd.o COBJS-$(CONFIG_USB_SL811HS) += sl811_usb.o COBJS-$(CONFIG_USB_EHCI_FSL) += usb_ehci_fsl.o +COBJS-$(CONFIG_USB_EHCI_PCI) += usb_ehci_pci.o # device ifdef CONFIG_USB_DEVICEdrivers/usb/usb_ehci_pci.c new file +64
-1@@ -0,0 +1,64 @@ +/*- +* Copyright (c) 2007-2008, Juniper Networks, Inc. +* All rights reserved. +* +* This program is free software; you can redistribute it and/or +* modify it under the terms of the GNU General Public License as +* published by the Free Software Foundation version 2 of +* the License. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +* GNU General Public License for more details. +* +* You should have received a copy of the GNU General Public License +* along with this program; if not, write to the Free Software +* Foundation, Inc., 59 Temple Place, Suite 330, Boston, +* MA 02111-1307 USA +*/ + +#include <common.h> +#include <pci.h> +#include <usb.h> +#include "usb_ehci.h" +#include "usb_ehci_core.h" + +#ifdef CONFIG_PCI_EHCI_DEVICE +static struct pci_device_id ehci_pci_ids[] = { +/* Please add supported PCI EHCI controller ids here */ + {0 ,0 } +}; +#endif + +/* +* Create the appropriate control structures to manage +* a new EHCI host controller. +*/ +int ehci_hcd_init (void ) +{ +pci_dev_t pdev; +uint32_t addr; + + pdev =pci_find_devices (ehci_pci_ids,CONFIG_PCI_EHCI_DEVICE ); +if (pdev ==-1 ) { +printf ("EHCI host controller not found\n" ); +return -1 ; + } + +pci_read_config_dword (pdev,PCI_BASE_ADDRESS_0 , &addr); + hccr = (struct ehci_hccr *)addr; + hcor = (struct ehci_hcor *)((uint32_t ) hccr + +HC_LENGTH (ehci_readl (&hccr->cr_capbase))); + +return 0 ; +} + +/* +* Destroy the appropriate control structures corresponding +* the the EHCI host controller. +*/ +int ehci_hcd_stop (void ) +{ +return 0 ; +} --1.5.6.5
cover USB ehci pci initial support
Hi,
Quoted 15 lines · Remy Bohmer
Hello Michael,
2008/12/17 Michael Trimarchi <[email protected]>:
Quoted 11 lines
Add USB ehci pci support. This patch doesn't include any
pci_idsand it is not tested on real hardware. To use it add (for example) the following in the board configuration file:#define
CONFIG_CMD_USB1
#defineCONFIG_USB_STORAGE1
#defineCONFIG_USB_EHCI
#defineCONFIG_USB_EHCI_PCI1
#defineCONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS2
#defineCONFIG_LEGACY_USB_INIT_SEQ1
#defineCONFIG_PCI_EHCI_DEVICE1
Quoted 8 lines
I think that this kind of information should be put in the toplevel README file. A note where to put the PCI-ids is also nice.
Kind Regards,
Remy
Ok I rework the patch and send again.
Quoted 95 lines
Quoted 94 lines
Signed-off-by Michael Trimarchi <[email protected]>--- drivers/usb/Makefile | 1 + drivers/usb/usb_ehci_pci.c | 64 ++++++++++++++++++++++++++++++++++++++++++++ 2 files changed, 65 insertions(+), 0 deletions(-) create mode 100644 drivers/usb/usb_ehci_pci.cdrivers/usb/Makefile +1
-0@@ -35,6 +35,7 @@ COBJS-$(CONFIG_USB_ISP116X_HCD) += isp116x-hcd.o COBJS-$(CONFIG_USB_R8A66597_HCD) += r8a66597-hcd.o COBJS-$(CONFIG_USB_SL811HS) += sl811_usb.o COBJS-$(CONFIG_USB_EHCI_FSL) += usb_ehci_fsl.o +COBJS-$(CONFIG_USB_EHCI_PCI) += usb_ehci_pci.o # device ifdef CONFIG_USB_DEVICEdrivers/usb/usb_ehci_pci.c new file +64
-1@@ -0,0 +1,64 @@ +/*- +* Copyright (c) 2007-2008, Juniper Networks, Inc. +* All rights reserved. +* +* This program is free software; you can redistribute it and/or +* modify it under the terms of the GNU General Public License as +* published by the Free Software Foundation version 2 of +* the License. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +* GNU General Public License for more details. +* +* You should have received a copy of the GNU General Public License +* along with this program; if not, write to the Free Software +* Foundation, Inc., 59 Temple Place, Suite 330, Boston, +* MA 02111-1307 USA +*/ + +#include <common.h> +#include <pci.h> +#include <usb.h> +#include "usb_ehci.h" +#include "usb_ehci_core.h" + +#ifdef CONFIG_PCI_EHCI_DEVICE +static struct pci_device_id ehci_pci_ids[] = { +/* Please add supported PCI EHCI controller ids here */ + {0 ,0 } +}; +#endif + +/* +* Create the appropriate control structures to manage +* a new EHCI host controller. +*/ +int ehci_hcd_init (void ) +{ +pci_dev_t pdev; +uint32_t addr; + + pdev =pci_find_devices (ehci_pci_ids,CONFIG_PCI_EHCI_DEVICE ); +if (pdev ==-1 ) { +printf ("EHCI host controller not found\n" ); +return -1 ; + } + +pci_read_config_dword (pdev,PCI_BASE_ADDRESS_0 , &addr); + hccr = (struct ehci_hccr *)addr; + hcor = (struct ehci_hcor *)((uint32_t ) hccr + +HC_LENGTH (ehci_readl (&hccr->cr_capbase))); + +return 0 ; +} + +/* +* Destroy the appropriate control structures corresponding +* the the EHCI host controller. +*/ +int ehci_hcd_stop (void ) +{ +return 0 ; +} --1.5.6.5