Skip to contentSkip to conversation

gpio: gpio_{request,free}() now required (feature removal)

PATCH New David Brownell 1 participant 1 message Feb 4, 2009

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 gpio: gpio_{request,free}() now required (feature removal)

From: David Brownell <[email protected]>

We want to phase out the GPIO "autorequest" mechanism in gpiolib and require all callers to use gpio_request().

- Update feature-removal-schedule
- Update the documentation now
- Convert the relevant pr_warning() in gpiolib to a WARN() so folk using this mechanism get a noisy stack dump

Some drivers and board init code will probably need to change. Implementations not using gpiolib will still be fine; they are already required to implement gpio_{request,free}() stubs.

---
 Documentation/feature-removal-schedule.txt |   12 ++++++++++++
 Documentation/gpio.txt                     |   23 +++++++++--------------
 drivers/gpio/gpiolib.c                     |   12 ++++++++----
 3 files changed, 29 insertions(+), 18 deletions(-)
Documentation/feature-removal-schedule.txt +12 -0
@@ -335,3 +335,15 @@ Why:	In 2.6.18 the Secmark concept was i
 	Secmark, it is time to deprecate the older mechanism and start the
 	process of removing the old code.
 Who:	Paul Moore <[email protected]>
+
+---------------------------
+
+What:	GPIO autorequest on gpio_direction_{input,output}() in gpiolib
+When:	February 2010
+Why:	All callers should use explicit gpio_request()/gpio_free().
+	The autorequest mechanism in gpiolib was provided mostly as a
+	migration aid for legacy GPIO interfaces (for SOC based GPIOs).
+	Those users have now largely migrated.  Platforms implementing
+	the GPIO interfaces without using gpiolib will see no changes.
+Who:	David Brownell <[email protected]>
+
Documentation/gpio.txt +9 -14
@@ -123,7 +123,10 @@ platform-specific implementation issue.
 
 Using GPIOs
 -----------
-One of the first things to do with a GPIO, often in board setup code when
+The first thing a system should do with a GPIO is allocate it, using
+the gpio_request() call; see later.
+
+One of the next things to do with a GPIO, often in board setup code when
 setting up a platform_device using the GPIO, is mark its direction:
 
 	/* set as input or output, returning 0 or negative errno */
@@ -141,8 +144,8 @@ This helps avoid signal glitching during
 
 For compatibility with legacy interfaces to GPIOs, setting the direction
 of a GPIO implicitly requests that GPIO (see below) if it has not been
-requested already.  That compatibility may be removed in the future;
-explicitly requesting GPIOs is strongly preferred.
+requested already.  That compatibility is being removed from the optional
+gpiolib framework.
 
 Setting the direction can fail if the GPIO number is invalid, or when
 that particular GPIO can't be used in that mode.  It's generally a bad
@@ -195,7 +198,7 @@ This requires sleeping, which can't be d
 
 Platforms that support this type of GPIO distinguish them from other GPIOs
 by returning nonzero from this call (which requires a valid GPIO number,
-either explicitly or implicitly requested):
+which should have been previously allocated with gpio_request):
 
 	int gpio_cansleep(unsigned gpio);
 
@@ -212,10 +215,9 @@ for GPIOs that can't be accessed from IR
 same as the spinlock-safe calls.
 
 
-Claiming and Releasing GPIOs (OPTIONAL)
----------------------------------------
+Claiming and Releasing GPIOs
+----------------------------
 To help catch system configuration errors, two calls are defined.
-However, many platforms don't currently support this mechanism.
 
 	/* request GPIO, returning 0 or negative errno.
 	 * non-null labels may be useful for diagnostics.
@@ -244,13 +246,6 @@ Some platforms may also use knowledge ab
 power management, such as by powering down unused chip sectors and, more
 easily, gating off unused clocks.
 
-These two calls are optional because not not all current Linux platforms
-offer such functionality in their GPIO support; a valid implementation
-could return success for all gpio_request() calls.  Unlike the other calls,
-the state they represent doesn't normally match anything from a hardware
-register; it's just a software bitmap which clearly is not necessary for
-correct operation of hardware or (bug free) drivers.
-
 Note that requesting a GPIO does NOT cause it to be configured in any
 way; it just marks that GPIO as in use.  Separate code must handle any
 pin setup (e.g. controlling which pin the GPIO uses, pullup/pulldown).
drivers/gpio/gpiolib.c +8 -4
@@ -69,20 +69,24 @@ static inline void desc_set_label(struct
  * those calls have no teeth) we can't avoid autorequesting.  This nag
  * message should motivate switching to explicit requests... so should
  * the weaker cleanup after faults, compared to gpio_request().
+ *
+ * NOTE: the autorequest mechanism is going away; at this point it's
+ * only "legal" in the sense that (old) code using it won't break yet,
+ * but instead only triggers a WARN() stack dump.
  */
 static int gpio_ensure_requested(struct gpio_desc *desc, unsigned offset)
 {
-	if (test_and_set_bit(FLAG_REQUESTED, &desc->flags) == 0) {
-		struct gpio_chip *chip = desc->chip;
-		int gpio = chip->base + offset;
+	const struct gpio_chip *chip = desc->chip;
+	const int gpio = chip->base + offset;
 
+	if (WARN(test_and_set_bit(FLAG_REQUESTED, &desc->flags) == 0,
+			"autorequest GPIO-%d\n", gpio)) {
 		if (!try_module_get(chip->owner)) {
 			pr_err("GPIO-%d: module can't be gotten \n", gpio);
 			clear_bit(FLAG_REQUESTED, &desc->flags);
 			/* lose */
 			return -EIO;
 		}
-		pr_warning("GPIO-%d autorequested\n", gpio);
 		desc_set_label(desc, "[auto]");
 		/* caller must chip->request() w/o spinlock */
 		if (chip->request)