Tuning problems with loss of TS packets
Hello,
sometimes, I experience non-deterministic problems with tuning on some transponders with dvb-s. For example, on astra-H-11954, I have about 50% chance to get a good tune. If I get a bad tune, I still receive TS packets from the chosen transponder, but about 10%..20% of the packets are lost. The (remaining) packets contain PAT/PMT/PES packets from the chosen transponder, so it is pretty safe to assume that actual tuning worked properly.
What I do is pretty much straight forward:
1. open frontend/dmx/dvr devices
2. send diseqc command to switch to desired input
3. use FE_SET_FRONTEND ioctl to tune to desired transponder
4. wait for FE_HAS_LOCK
5. set dmx_pesfilter_params to:
pid: 0x2000 /* yes, I want the whole transponder */
input: DMX_IN_FRONTEND
output: DMX_OUT_TS_TAP pes_type: DMX_PES_OTHER
flags: DMX_IMMEDIATE_START
With this sequence, I have about 50% chance to receive a proper TS stream. When the stream is not OK, I can see about 10%..20% loss of TS packets.
I have checked signal quality, but there is no significant difference from working to non-working:
Status:1f sig:ac80 snr:d9e0 ber:00000000 unc:fffffffe FE_HAS_LOCK Status:1f sig:adbe snr:dac4 ber:00000000 unc:fffffffe FE_HAS_LOCK
So I have tried to narrow the problem, and I think I've come pretty close (but still no cigar):
Once the sequence (which is listed above) is completed, I can easily (but randomly, IOW: I have to try 1..3 times) switch from proper stream to broken stream and vice-versa simply by repeating step 3 with _exactly_ the _same_ values.
To be precise: on an already set-up transponder, re-executing this function:
static void tune_frequency (int ifreq, int sr)
{
struct dvb_frontend_parameters tuneto;
tuneto.frequency = ifreq*1000;
tuneto.inversion = INVERSION_AUTO;
tuneto.u.qpsk.symbol_rate = sr*1000;
tuneto.u.qpsk.fec_inner = FEC_AUTO;
if (ioctl(fefd, FE_SET_FRONTEND, &tuneto) == -1) {
fatal ("FE_SET_FRONTEND failed: %s\n", strerror (errno));
}}
with _exactly_ the same values for ifreq and sr, is able to toggle from good TS stream to bad TS stream or vice-versa. As long as I avoid to call this function, the quality of the stream does _not_ change.
I have tried to use fixed values instead of *_AUTO for FEC and INVERSION, but that did not help either.
Any ideas?
BTW:
$ lspci -v
[ ... ]
03:07.0 Multimedia controller: Philips Semiconductors SAA7146 (rev 01)
Subsystem: Technotrend Systemtechnik GmbH Technotrend-Budget/Hauppauge WinTV-NOVA-CI DVB card
Flags: bus master, medium devsel, latency 32, IRQ 21
Memory at fdcfe000 (32-bit, non-prefetchable) [size=512]
Kernel driver in use: budget_ci dvb
Kernel modules: snd-aw2, budget-ci
$ uname -a
Linux raven 2.6.27.7-9-default #1 SMP 2008-12-04 18:10:04 +0100 x86_64 x86_64 x86_64 GNU/Linux_______________________________________________
linux-dvb users mailing list
For V4L/DVB development, please use instead [email protected] [email protected]
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
Quoted 56 lines · Josef Wolf
Hello,
sometimes, I experience non-deterministic problems with tuning on some transponders with dvb-s. For example, on astra-H-11954, I have about 50% chance to get a good tune. If I get a bad tune, I still receive TS packets from the chosen transponder, but about 10%..20% of the packets are lost. The (remaining) packets contain PAT/PMT/PES packets from the chosen transponder, so it is pretty safe to assume that actual tuning worked properly.
What I do is pretty much straight forward:
1. open frontend/dmx/dvr devices
2. send diseqc command to switch to desired input
3. useFE_SET_FRONTENDioctl to tune to desired transponder
4. wait forFE_HAS_LOCK
5. setdmx_pesfilter_paramsto:pid: 0x2000 /* yes, I want the whole transponder */ input: DMX_IN_FRONTEND output: DMX_OUT_TS_TAP
pes_type:DMX_PES_OTHER
flags:DMX_IMMEDIATE_STARTWith this sequence, I have about 50% chance to receive a proper TS stream. When the stream is not OK, I can see about 10%..20% loss of TS packets.
I have checked signal quality, but there is no significant difference from working to non-working:
Status:1f sig:ac80 snr:d9e0 ber:00000000 unc:fffffffe
FE_HAS_LOCKStatus:1f sig:adbe snr:dac4 ber:00000000 unc:fffffffeFE_HAS_LOCKSo I have tried to narrow the problem, and I think I've come pretty close (but still no cigar):
Once the sequence (which is listed above) is completed, I can easily (but randomly, IOW: I have to try 1..3 times) switch from proper stream to broken stream and vice-versa simply by repeating step 3 with _exactly_ the _same_ values.
To be precise: on an already set-up transponder, re-executing this function:
static void
tune_frequency(int ifreq, int sr){ struct dvb_frontend_parameters tuneto; tuneto.frequency = ifreq*1000; tuneto.inversion = INVERSION_AUTO; tuneto.u.qpsk.symbol_rate = sr*1000; tuneto.u.qpsk.fec_inner = FEC_AUTO; if (ioctl(fefd, FE_SET_FRONTEND, &tuneto) == -1) { fatal ("FE_SET_FRONTEND failed: %s\n", strerror (errno)); }
Quoted 5 lines
}
with _exactly_ the same values for ifreq and sr, is able to toggle from good TS stream to bad TS stream or vice-versa. As long as I avoid to call this function, the quality of the stream does _not_ change.
I had exactly the same behavior of Twinhan SP-200 (1027) card until I totally gave up and bought Twinhan SP-400 (1041) card. Interesting if those 2 cards have the same components.
Quoted 6 lines
I have tried to use fixed values instead of
*_AUTOfor FEC and INVERSION, but that did not help either.Any ideas?
What driver repository you use? And what driver is loaded for that card? My guess was that the tuner is not properly reset/set before the tuning. But (again) since I don't have any chip specification, I didn't have much progress with that.
Quoted 16 lines
BTW:
$ lspci -v [ ... ] 03:07.0 Multimedia controller: Philips Semiconductors SAA7146 (rev 01) Subsystem: Technotrend Systemtechnik GmbH Technotrend-Budget/Hauppauge WinTV-NOVA-CI DVB card Flags: bus master, medium devsel, latency 32, IRQ 21 Memory at fdcfe000 (32-bit, non-prefetchable) [size=512] Kernel driver in use: budget_ci dvb Kernel modules: snd-aw2, budget-ci $ uname -a Linux raven 2.6.27.7-9-default #1 SMP 2008-12-04 18:10:04 +0100 x86_64 x86_64 x86_64 GNU/Linux
Quoted 6 lines
_______________________________________________
linux-dvb users mailing list
For V4L/DVB development, please use instead [email protected] [email protected]
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
_______________________________________________
linux-dvb users mailing list
For V4L/DVB development, please use instead [email protected] [email protected]
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
On Sat, Feb 07, 2009 at 11:12:25AM +0200, Alex Betis wrote:
[ ... ]
Quoted 17 lines
Quoted 17 lines
To be precise: on an already set-up transponder, re-executing this function:
static void
tune_frequency(int ifreq, int sr){ struct dvb_frontend_parameters tuneto; tuneto.frequency = ifreq*1000; tuneto.inversion = INVERSION_AUTO; tuneto.u.qpsk.symbol_rate = sr*1000; tuneto.u.qpsk.fec_inner = FEC_AUTO; if (ioctl(fefd, FE_SET_FRONTEND, &tuneto) == -1) { fatal ("FE_SET_FRONTEND failed: %s\n", strerror (errno)); }}
Quoted 7 lines
Quoted 3 lines
with _exactly_ the same values for ifreq and sr, is able to toggle from good TS stream to bad TS stream or vice-versa. As long as I avoid to call this function, the quality of the stream does _not_ change.
I had exactly the same behavior of Twinhan SP-200 (1027) card until I totally gave up and bought Twinhan SP-400 (1041) card. Interesting if those 2 cards have the same components.
The cards I have are of those:
http://www.linuxtv.org/wiki/index.php/TechnoTrend_PCline_budget_DVB-S
Do you think the problem is related to hardware?
Quoted 9 lines
Quoted 4 lines
I have tried to use fixed values instead of
*_AUTOfor FEC and INVERSION, but that did not help either.Any ideas?
What driver repository you use? And what driver is loaded for that card? My guess was that the tuner is not properly reset/set before the tuning. But (again) since I don't have any chip specification, I didn't have much progress with that.
# lsmod|egrep '(dvb|budget|stv|saa|ttpci)' stv0299 11280 1 budget_ci 18956 3 budget_core 12332 1 budget_ci dvb_core 87948 3 stv0299,budget_ci,budget_core saa7146 18080 2 budget_ci,budget_core ttpci_eeprom 2520 1 budget_core ir_common 43340 1 budget_ci i2c_core 35280 5 stv0299,budget_ci,budget_core,ttpci_eeprom,i2c_piix4
#
I have not yet compiled my own drivers, so I use the drivers that came with the disro (opensuse-11.1, x86_64). But I am about to dive into the driver to narrow down the problem closer. Any hint how to compile my own drivers on opensuse?
_______________________________________________
linux-dvb users mailing list
For V4L/DVB development, please use instead [email protected] [email protected]
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
Quoted 23 lines · Josef Wolf
On Sat, Feb 07, 2009 at 11:12:25AM +0200, Alex Betis wrote:
[ ... ]Quoted 21 lines
Quoted 20 lines
To be precise: on an already set-up transponder, re-executing this function:
static void
tune_frequency(int ifreq, int sr){ struct dvb_frontend_parameters tuneto; tuneto.frequency = ifreq*1000; tuneto.inversion = INVERSION_AUTO; tuneto.u.qpsk.symbol_rate = sr*1000; tuneto.u.qpsk.fec_inner = FEC_AUTO; if (ioctl(fefd, FE_SET_FRONTEND, &tuneto) == -1) { fatal ("FE_SET_FRONTEND failed: %s\n", strerror (errno)); }}
with _exactly_ the same values for ifreq and sr, is able to toggle from good TS stream to bad TS stream or vice-versa. As long as I avoid to call this function, the quality of the stream does _not_ change.
Quoted 7 lines
Quoted 3 lines
I had exactly the same behavior of Twinhan SP-200 (1027) card until I totally gave up and bought Twinhan SP-400 (1041) card. Interesting if those 2 cards have the same components.
The cards I have are of those:
http://www.linuxtv.org/wiki/index.php/TechnoTrend_PCline_budget_DVB-S
Do you think the problem is related to hardware?
Since the tuning works from time to time, I tend to think that its a driver problem.
Quoted 22 lines
Quoted 3 lines
Quoted 3 lines
I have tried to use fixed values instead of
*_AUTOfor FEC andINVERSION,
Quoted 8 lines
Quoted 3 lines
but that did not help either.
Any ideas?
What driver repository you use? And what driver is loaded for that card? My guess was that the tuner is not properly reset/set before the tuning. But (again) since I don't have any chip specification, I didn't have much progress with that.
# lsmod|egrep '(dvb|budget|stv|saa|ttpci)' stv0299 11280 1 budget_ci 18956 3 budget_core 12332 1 budget_ci dvb_core 87948 3 stv0299,budget_ci,budget_core saa7146 18080 2 budget_ci,budget_core ttpci_eeprom 2520 1 budget_core ir_common 43340 1 budget_ci i2c_core 35280 5
Quoted 3 lines
stv0299,budget_ci,budget_core,ttpci_eeprom,i2c_piix4
#
Don't remember when drivers it used, I've removed it from my box long ago.
Quoted 5 lines
I have not yet compiled my own drivers, so I use the drivers that came with the disro (opensuse-11.1,
x86_64). But I am about to dive into the driver to narrow down the problem closer. Any hint how to compile my own drivers on opensuse?
I dont have opensuse, but I'd suggest to use this repository:
http://mercurial.intuxication.org/hg/s2-liplianin
Quoted 8 lines
_______________________________________________
linux-dvb users mailing list
For V4L/DVB development, please use instead [email protected] [email protected]
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
_______________________________________________
linux-dvb users mailing list
For V4L/DVB development, please use instead [email protected] [email protected]
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
Quoted 9 lines · Josef Wolf
Hello,
sometimes, I experience non-deterministic problems with tuning on some transponders with dvb-s. For example, on astra-H-11954, I have about 50% chance to get a good tune. If I get a bad tune, I still receive TS packets from the chosen transponder, but about 10%..20% of the packets are lost. The (remaining) packets contain PAT/PMT/PES packets from the chosen transponder, so it is pretty safe to assume that actual tuning worked properly.
I have tried to analyze the cc (continuation counter) field of the TS packets to get more clue. This is what I found on the astra-H-11954 (zdf) transponder:
When I get a "bad" tune (that is: mplayer and vlc get stuck), the cc errors are unsystematic. All PIDs are affected, and the amount of lost packets varies. But from time to time regularities can be seen:
cc pid:967 expect:3 got:5 *
cc pid:970 expect:3 got:5 *
cc pid:966 expect:3 got:5 *
cc pid:18 expect:10 got:11
cc pid:969 expect:5 got:6
cc pid:131 expect:10 got:9
cc pid:710 expect:7 got:11
cc pid:967 expect:13 got:15 *
cc pid:970 expect:13 got:15 *
cc pid:966 expect:13 got:15 *
cc pid:968 expect:11 got:13
cc pid:230 expect:12 got:15
cc pid:330 expect:5 got:8
cc pid:620 expect:1 got:5
cc pid:130 expect:5 got:9 +
cc pid:630 expect:5 got:9 +
cc pid:220 expect:6 got:10
cc pid:120 expect:14 got:2
cc pid:968 expect:4 got:6
cc pid:967 expect:7 got:9 *
cc pid:970 expect:7 got:9 *
cc pid:966 expect:7 got:9 *I have marked the interesting lines. Most interesting are the lines marked with stars. This is the same sequence of PIDs in the same order and with the same amount of lost packets. This does not look like a coincidence to me.
_______________________________________________
linux-dvb users mailing list
For V4L/DVB development, please use instead [email protected] [email protected]
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb