Enable Ethernet for Nomadik 8815 Eval Kit
PATCH 1/1 Enable Ethernet for Nomadik 8815 Eval Kit
From: Alessandro Rubini <[email protected]>
This trivially enables Ethernet support in the debug board by setting up the proper chip select.
Signed-off-by Alessandro Rubini <[email protected]>
Acked-by Andrea Gallo <[email protected]>
--- board/st/nmdk8815/nmdk8815.c | 5 ++++- include/configs/nmdk8815.h | 3 +++ 2 files changed, 7 insertions(+), 1 deletions(-)
board/st/nmdk8815/nmdk8815.c +4 -1
@@ -49,8 +49,11 @@ int board_init(void)writel (0x00000000 ,NOMADIK_GPIO1_BASE +0x28 );writel (readl (NOMADIK_SRC_BASE ) |0x8000 ,NOMADIK_SRC_BASE ); -icache_enable (); +/* Set up SMCS1 for Ethernet: sram-like, enabled, timing values */ +writel (0x0000305b ,NOMADIK_FSMC_BASE +0x08 );/* FSMC_BCR1 */ +writel (0x00033f33 ,NOMADIK_FSMC_BASE +0x0c );/* FSMC_BTR1 */ +icache_enable ();return 0 ; }
include/configs/nmdk8815.h +3 -0
@@ -35,8 +35,11 @@/* commands */ #include <config_cmd_default.h> + +#define CONFIG_CMD_NET #define CONFIG_CMD_PING #define CONFIG_CMD_DHCP +#define CONFIG_CMD_NFS /* There is no NOR flash, so undefine these commands */ #undef CONFIG_CMD_FLASH#undef CONFIG_CMD_IMLS
Signature · 1 line
1.6.0.2
PATCH v2 1/1 Enable Ethernet for Nomadik 8815 Eval Kit
From: Alessandro Rubini <[email protected]>
This trivially enables Ethernet support in the debug board by setting up the proper chip select.
Signed-off-by Alessandro Rubini <[email protected]>
Acked-by Andrea Gallo <[email protected]>
---
Changes from V1: use register names defined in the header introduced by patch "Nand driver for Nomadik SoC" (argh... I hope I should not split that one in two different patches, one for the header and one for the nand)
board/st/nmdk8815/nmdk8815.c | 5 ++++- include/configs/nmdk8815.h | 3 +++ 2 files changed, 7 insertions(+), 1 deletions(-)
board/st/nmdk8815/nmdk8815.c +4 -1
@@ -49,8 +49,11 @@ int board_init(void)writel (0x00000000 ,NOMADIK_GPIO1_BASE +0x28 );writel (readl (NOMADIK_SRC_BASE ) |0x8000 ,NOMADIK_SRC_BASE ); -icache_enable (); +/* Set up SMCS1 for Ethernet: sram-like, enabled, timing values */ +writel (0x0000305b ,REG_FSMC_BCR1 ); +writel (0x00033f33 ,REG_FSMC_BTR1 ); +icache_enable ();return 0 ; }
include/configs/nmdk8815.h +3 -0
@@ -37,8 +37,11 @@/* commands */ #include <config_cmd_default.h> + +#define CONFIG_CMD_NET #define CONFIG_CMD_PING #define CONFIG_CMD_DHCP +#define CONFIG_CMD_NFS /* There is no NOR flash, so undefine these commands */ #undef CONFIG_CMD_FLASH#undef CONFIG_CMD_IMLS
Signature · 1 line
1.6.0.2