hda - enable SPDIF output for Intel DX58SO board
PATCH 1/1 hda - enable SPDIF output for Intel DX58SO board
ALC889 has two SPDIF outputs: 0x06, 0x10. Board vendors can use either or both. DX58SO uses 0x10, but the driver assumes 0x06. The safe solution is to add 0x10 as slave output to the existing 0x06.
Reported-by Jeroen Van Breedam <[email protected]>
Tested-by Jeroen Van Breedam <[email protected]>
Signed-off-by Wu Fengguang <[email protected]>
--- sound/pci/hda/patch_realtek.c | 5 +++++ 1 file changed, 5 insertions(+)
sound/pci/hda/patch_realtek.c +5 -0
@@ -8764,6 +8764,10 @@ static struct snd_pci_quirk alc883_cfg_t {} }; +static hda_nid_t alc883_slave_dig_outs[] = { +ALC1200_DIGOUT_NID ,0 , +}; +static hda_nid_t alc1200_slave_dig_outs[] = {ALC883_DIGOUT_NID ,0 , };
@@ -8809,6 +8813,7 @@ static struct alc_config_preset alc883_p .dac_nids = alc883_dac_nids, .dig_out_nid = ALC883_DIGOUT_NID, .dig_in_nid = ALC883_DIGIN_NID, + .slave_dig_outs = alc883_slave_dig_outs, .num_channel_mode = ARRAY_SIZE(alc883_3ST_6ch_intel_modes), .channel_mode = alc883_3ST_6ch_intel_modes, .need_dac_fix = 1,
At Thu, 2 Apr 2009 19:44:18 +0800,
Quoted 8 lines · Wu Fengguang
ALC889 has two SPDIF outputs:
0x06,0x10. Board vendors can use either or both. DX58SO uses0x10, but the driver assumes0x06. The safe solution is to add0x10as slave output to the existing0x06.Reported-by Jeroen Van Breedam <[email protected]>Tested-by Jeroen Van Breedam <[email protected]>Signed-off-by Wu Fengguang <[email protected]>
Applied now. Thanks.
Takashi
Quoted 26 lines
--- sound/pci/hda/patch_realtek.c | 5 +++++ 1 file changed, 5 insertions(+)sound/pci/hda/patch_realtek.c +5
-0@@ -8764,6 +8764,10 @@ static struct snd_pci_quirk alc883_cfg_t {} }; +static hda_nid_t alc883_slave_dig_outs[] = { +ALC1200_DIGOUT_NID ,0 , +}; +static hda_nid_t alc1200_slave_dig_outs[] = {ALC883_DIGOUT_NID ,0 , };@@ -8809,6 +8813,7 @@ static struct alc_config_preset alc883_p .dac_nids = alc883_dac_nids, .dig_out_nid = ALC883_DIGOUT_NID, .dig_in_nid = ALC883_DIGIN_NID, + .slave_dig_outs = alc883_slave_dig_outs, .num_channel_mode = ARRAY_SIZE(alc883_3ST_6ch_intel_modes), .channel_mode = alc883_3ST_6ch_intel_modes, .need_dac_fix = 1,