dm355 evm support (v2)
PATCH 1/1 dm355 evm support (v2)
From: David Brownell <[email protected]>
Initial U-Boot support for the DaVinci DM355 EVM. This is a board from Spectrum Digital. Board docs include schematic and firmware for its microcontroller:
http://c6000.spectrumdigital.com/evmdm355/revd/
Most of the DM355 chip is fully documented by TI, the most notable exception being the MPEG/JPEG coprocessor (programmable using codecs available at no cost from TI), which is omitted from its DM335 sibling:
http://focus.ti.com/docs/prod/folders/print/tms320dm355.html
This version can boot from the on-board DM9000 Ethernet chip, after being loaded (from NAND, MMC/SD, or UART). In the near future, NAND and USB support could be added ... NAND support is being held back until the support for the 4-bit ECC hardware is ready.
---
NOTE: presumes the rework of chipselect handling in the NAND code, but that should only be visible if someone enables that driver.
MAKEALL | 1 Makefile | 3 board/davinci/dm355evm/Makefile | 52 +++++++++ board/davinci/dm355evm/config.mk | 11 + board/davinci/dm355evm/dm355evm.c | 110 +++++++++++++++++++ include/configs/davinci_dm355evm.h | 194 +++++++++++++++++++++++++++++++++++ 6 files changed, 371 insertions(+)
MAKEALL +1 -0
@@ -527,6 +527,7 @@ LIST_ARM9=" \ davinci_schmoogie \ davinci_sffsdr \ davinci_sonata \ + davinci_dm355evm \ " #########################################################################
Makefile +3 -0
@@ -2790,6 +2790,9 @@ davinci_sffsdr_config : unconfig davinci_sonata_config : unconfig @$(MKCONFIG) $(@:_config=) arm arm926ejs sonata davinci davinci +davinci_dm355evm_config : unconfig + @$(MKCONFIG) $(@:_config=) arm arm926ejs dm355evm davinci davinci + lpd7a400_config \ lpd7a404_config: unconfig @$(MKCONFIG) $(@:_config=) arm lh7a40x lpd7a40x
board/davinci/dm355evm/Makefile new file +52 -0
52 lines not on this page · raw message
board/davinci/dm355evm/config.mk new file +11 -0
@@ -0,0 +1,11 @@ +# +# Spectrum Digital DM355 EVM board +# dm355evm board has 1 bank of 128 MB DDR RAM +# Physical Address: 8000'0000 to 8800'0000 +# +# Linux Kernel is expected to be at 8000'8000, entry 8000'8000 +# (mem base + reserved) +# + +#Provide at least 16MB spacing between us and the Linux Kernel image +TEXT_BASE = 0x81080000
board/davinci/dm355evm/dm355evm.c new file +110 -0
110 lines not on this page · raw message
include/configs/davinci_dm355evm.h new file +194 -0
194 lines not on this page · raw message
PATCH 1/1 dm355 evm support (v2)
Quoted 69 lines
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */board/davinci/dm355evm/dm355evm.c new file +57
-0+ +#include <common.h> +#include <nand.h> +#include <asm/io.h> +#include <asm/arch/hardware.h> +#include <asm/arch/emif_defs.h> +#include <asm/arch/nand_defs.h> +#include "../common/misc.h" + + +DECLARE_GLOBAL_DATA_PTR ; + +/* +* With the DM355 EVM, u-boot is *always* a third stage loader, +* unless a JTAG debugger handles the first two stages: +* +* - 1st stage is ROM Boot Loader (RBL), which searches for a +* second stage loader in one of three places based on SW7: +* NAND (with MMC/SD fallback), MMC/SD, or UART. +* +* - 2nd stage is User Boot Loader (UBL), using at most 30KB +* of on-chip SRAM, responsible for lowlevel init, and for +* loading the third stage loader into DRAM. +* +* - 3rd stage, that's us! +*/ + +int board_init (void ) +{ + gd->bd->bi_arch_number =MACH_TYPE_DAVINCI_DM355_EVM ; + gd->bd->bi_boot_params =PHYS_SDRAM_1 +0x100 ; + +/* We expect the UBL to have handled "lowlevel init", which +* involves setting up at least: +* - clocks +* + PLL1 (for ARM and peripherals) and PLL2 (for DDR) +* + clock divisors for those PLLs +* + LPSC_DDR module enabled +* + LPSC_TIMER0 module (still) enabled +* - EMIF +* + DDR init and timings +* + AEMIF timings (for NAND and DM9000) +* - pinmux +* +* Some of that is repeated here, mostly as a precaution. +*/ + +/* AEMIF: Some "address" lines are available as GPIOs. A3..A13 +* could be too if we used A12 as a GPIO during NAND chipselect +* (and Linux did too), letting us control the LED on A7/GPIO61. +*/ +REG (PINMUX2 ) =0x0c08 ; + +/* UART0 may still be in SyncReset if we didn't boot from UART */ +davinci_enable_uart0 (); + +/* EDMA may be in SyncReset too; turn it on, Linux won't (yet) */
board/davinci/dm355evm/dm355evm.c line 84
Quoted 10 lines
board/davinci/dm355evm/dm355evm.c new file +10
-0+lpsc_on (DAVINCI_LPSC_TPCC ); +lpsc_on (DAVINCI_LPSC_TPTC0 ); +lpsc_on (DAVINCI_LPSC_TPTC1 ); + +return 0 ; +} + +#ifdef CONFIG_NAND_DAVINCI + +#define BIT (x) (1 << (x))
please remove
or use set_bit
Quoted 35 lines
board/davinci/dm355evm/dm355evm.c new file +26
-0+ +static void nand_dm355evm_select_chip (struct mtd_info *mtd,int chip) +{ +struct nand_chip *this = mtd->priv; +u32 wbase = (u32 ) this->IO_ADDR_W; +u32 rbase = (u32 ) this->IO_ADDR_R; + +if (chip ==1 ) { + wbase |=BIT (14 ); + rbase |=BIT (14 ); + }else { + wbase &= ~BIT (14 ); + rbase &= ~BIT (14 ); + } + this->IO_ADDR_W = (void *)wbase; + this->IO_ADDR_R = (void *)rbase; +} + +int board_nand_init (struct nand_chip *nand) +{ +davinci_nand_init (nand); + nand->select_chip = nand_dm355evm_select_chip; +return 0 ; +} + +#endif include/configs/davinci_dm355evm.h new file +6
-0@@ -0,0 +1,194 @@ +/* +#define DM9000_IO CONFIG_DM9000_BASE +#define DM9000_DATA (CONFIG_DM9000_BASE + 2) + +/* I2C */ +#define CONFIG_HARD_I2C
include/configs/davinci_dm355evm.h line 16
Quoted 10 lines
include/configs/davinci_dm355evm.h new file +10
-0+#define CONFIG_DRIVER_DAVINCI_I2C +#define CONFIG_SYS_I2C_SPEED 400000 +#define CONFIG_SYS_I2C_SLAVE 0x10/* SMBus host address */ + +/* NAND: socketed, two chipselects, normally 2 GBytes */ +/* NYET -- #define CONFIG_NAND_DAVINCI */ +#define CONFIG_SYS_NAND_HW_ECC +#define CONFIG_SYS_NAND_USE_FLASH_BBT + +/*#define CONFIG_SYS_NAND_SMALLPAGE */
please remove if no need
include/configs/davinci_dm355evm.h line 80
Quoted 8 lines
include/configs/davinci_dm355evm.h new file +8
-0+#define CONFIG_SYS_NAND_LARGEPAGE +#define CONFIG_SYS_NAND_BASE_LIST { 0x02000000, } +/* socket has two chipselects, nCE0 gated by address BIT(14) */ +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_SYS_NAND_MAX_CHIPS 2 + +/* USB: OTG connector */ +/* #define CONFIG_USB_DAVINCI */
please remove if no need
Quoted 45 lines
include/configs/davinci_dm355evm.h new file +45
-0+ +/* U-Boot command configuration */ +#include <config_cmd_default.h> + +#undef CONFIG_CMD_BDI +#undef CONFIG_CMD_FLASH +#undef CONFIG_CMD_FPGA +#undef CONFIG_CMD_SETGETDCR + +#define CONFIG_CMD_ASKENV +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_I2C +#define CONFIG_CMD_PING +#define CONFIG_CMD_SAVES + +#ifdef CONFIG_NAND_DAVINCI +#define CONFIG_CMD_MTDPARTS +#define CONFIG_MTD_PARTITIONS +#define CONFIG_CMD_NAND +#define CONFIG_CMD_UBI +#define CONFIG_RBTREE +#endif + +/* TEMPORARY -- no safe place to save env, yet */ +#define CONFIG_ENV_IS_NOWHERE +#undef CONFIG_CMD_SAVEENV + +#ifdef CONFIG_USB_DAVINCI +#define CONFIG_MUSB_HCD +#define CONFIG_CMD_USB +#define CONFIG_USB_STORAGE +#else +#undef CONFIG_MUSB_HCD +#undef CONFIG_CMD_USB +#undef CONFIG_USB_STORAGE +#endif + +#define CONFIG_CRC32_VERIFY +#define CONFIG_MX_CYCLIC + +/* U-Boot general configuration */ +#undef CONFIG_USE_IRQ/* No IRQ/FIQ in U-Boot */ +#define CONFIG_BOOTFILE "uImage"/* Boot file name */ +#define CONFIG_SYS_PROMPT "DM355 EVM # "/* Monitor Command Prompt */ +#define CONFIG_SYS_CBSIZE 1024/* Console I/O Buffer Size */
include/configs/davinci_dm355evm.h line 135
Quoted 10 lines
include/configs/davinci_dm355evm.h new file +10
-0+#define CONFIG_SYS_PBSIZE /* Print buffer size */ \ + (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) +#define CONFIG_SYS_MAXARGS 16/* max number of command args */ +#define CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " +#define CONFIG_SYS_LONGHELP + +#define CONFIG_ENV_SIZE SZ_16K + +/*#define CONFIG_BOOTDELAY 5 */
please remove if no need
include/configs/davinci_dm355evm.h line 145
Quoted 10 lines
include/configs/davinci_dm355evm.h new file +10
-0+#define CONFIG_BOOTCOMMAND \ + "dhcp;bootm" +#define CONFIG_BOOTARGS \ + "console=ttyS0,115200n8 " \ + "root=/dev/mmcblk0p1 rootwait rootfstype=ext3 ro" + +#define CONFIG_CMDLINE_EDITING +#define CONFIG_VERSION_VARIABLE +#define CONFIG_TIMESTAMP +
Best Regards,
J.
PATCH 1/1 dm355 evm support (v2)
Quoted 4 lines · Jean-Christophe PLAGNIOL-VILLARD
Quoted 1 line
+#define BIT(x) (1 << (x))
please remove
or useset_bit
I think that should probably be added to all the bitops.h headers, or someplace similar. But, OK; __{set,clear}_bit() work here too.
Quoted 3 lines
Quoted 1 line
+/*#define
CONFIG_SYS_NAND_SMALLPAGE*/please remove if no need
OK, I'll just make a later #ifdef have an #else for that, kicking in when someone swaps out the largepage chip for a smallpage one.
Quoted 9 lines
include/configs/davinci_dm355evm.h line 80
Quoted 8 lines
include/configs/davinci_dm355evm.h new file +8
-0+#define CONFIG_SYS_NAND_LARGEPAGE +#define CONFIG_SYS_NAND_BASE_LIST { 0x02000000, } +/* socket has two chipselects, nCE0 gated by address BIT(14) */ +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_SYS_NAND_MAX_CHIPS 2 + +/* USB: OTG connector */ +/* #define CONFIG_USB_DAVINCI */ please remove if no need
That's a "NYET". It initializes a bit differently on this board because the on-chip PHY is newer, and also interchanges the D+/D- lines for better signal routing. It's there as a placeholder, and will be enabled later.
Quoted 3 lines
include/configs/davinci_dm355evm.h line 135
Quoted 2 lines
include/configs/davinci_dm355evm.h new file +2
-0+ +/*#define CONFIG_BOOTDELAY 5 */ please remove if no need
Again a NYET. When the NAND support kicks in, there will be an environment, and this can be enabled. Until then, it's a placeholder ... when booting from MMC, UART or JTAG, with no environment, hands-off booting is ill-advised.
Updated patch coming soon.
- dave