Skip to contentSkip to conversation

Seagate Barracuda 7200.11 ST31500341AS fw SD17

DISCUSSION Markus 4 participants 9 messages Jun 2, 2009 – Jun 3, 2009 1 message not in the archive

lore
Share & tools
lore

Markus

author
#0 lore raw

Hello!

I have some Seagate Barracuda 7200.11 ST31500341AS 1.5TB drives. They use the firmware SD17.
They time out at the flush write cache and sometimes on the identify command.
I know that sounds suspicious so I wrote to seagate but they told me my drives are ok. (Although I dont think so.)

This drive+fw is blacklisted in the kernel, but there is no firmware upgrade for these drives. (Only very few serial numbers are able to upgrade.)

Now I want to know after what period of the time the kernel timeouts at these commands!? And if this timeout can be increased (manually, small patch for the kernel) and the min/max/avg time could somehow be messured. Every timeout kicks the drives off the raid, so I disabled the write cache (hdparm -W0 /dev/sdx) but thats no solution, just a bad workaround.

Its a amd64 system with the 2.6.29.4 on an AM3 board with AMDs 790GX + SB750 Chipsets running in ahci mode.

Thanks for your time and support!

Markus

PS: Please CC me!

A message that is not in the archive (sent off-list or not yet received): [email protected]

author
#2 lore raw
Quoted 8 lines · Rui Santos
Quoted 2 lines

I have some Seagate Barracuda 7200.11 ST31500341AS 1.5TB drives. They use the firmware SD17.

Seagate recommends firmware SD1A for that HD.
However, I do not know if it will solve your problem. Jut try it...

Quoted 3 lines

This drive+fw is blacklisted in the kernel, but there is no firmware upgrade for these drives. (Only very few serial numbers are able to upgrade.)

I cant upgrade the firmware because the flash-utility will abort due to "not affected serial number". I tried SD1B, the very newest version. Cant find the SD1A for my drives.

Markus

#3 lore raw
Quoted 11 lines · Markus
Quoted 5 lines · Rui Santos
Quoted 1 line

I have some Seagate Barracuda 7200.11 ST31500341AS 1.5TB drives. They use the firmware SD17.

Seagate recommends firmware SD1A for that HD.
However, I do not know if it will solve your problem. Jut try it...

Quoted 1 line

This drive+fw is blacklisted in the kernel, but there is no firmware upgrade for these drives. (Only very few serial numbers are able to upgrade.)

I cant upgrade the firmware because the flash-utility will abort due to "not affected serial number". I tried SD1B, the very newest version. Cant find the SD1A for my drives.

Markus

I think you might have tried the wrong firmware file.
ST31500341AS needs http://www.seagate.com/staticfiles/support/downloads/firmware/Brinks-4D8H-SD1B.ISO

HTH,

Kay

author
#4 lore raw
Quoted 3 lines · Kay Diederichs
Quoted 2 lines · Markus
Quoted 1 line · Rui Santos
Quoted 1 line

I have some Seagate Barracuda 7200.11 ST31500341AS 1.5TB drives.

They

Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 1 line

use the firmware SD17.

Seagate recommends firmware SD1A for that HD.
However, I do not know if it will solve your problem. Jut try it...

Quoted 1 line

This drive+fw is blacklisted in the kernel, but there is no

firmware

Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line

upgrade for these drives. (Only very few serial numbers are able

to

Quoted 4 lines
Quoted 4 lines
Quoted 1 line
Quoted 1 line

upgrade.)

I cant upgrade the firmware because the flash-utility will abort due to "not affected serial number". I tried SD1B, the very newest

version.

Quoted 7 lines
Quoted 3 lines

Cant find the SD1A for my drives.

Markus

I think you might have tried the wrong firmware file. ST31500341AS needs

http://www.seagate.com/staticfiles/support/downloads/firmware/Brinks-4D8H-SD1B.ISO

I tried that one (compared md5sum). It does not work. It only works for "ST31500341AS, 9JU138-300 or -336, SD15 through SD1A ONLY!" So the utility fails and says the specific model could not be found.

Markus

author
#6 lore raw
Quoted 3 lines · Krzysztof Halasa
Quoted 1 line · Markus

http://www.seagate.com/staticfiles/support/downloads/firmware/Brinks-4D8H-SD1B.ISO

Quoted 5 lines
Quoted 3 lines

I tried that one (compared md5sum). It does not work. It only works for "ST31500341AS, 9JU138-300 or -336, SD15 through SD1A ONLY!"

Did you try to contact them?

Of course I did. They told me, my drives are not affected and drives with "good" serial numbers will not be upgraded.
And they now told me I have OEM drives (???) which they do not provide firmware upgrades for, although my drives are ok. I dont understand those support-people.

Markus

#7 lore raw
Quoted 8 lines · Markus
Quoted 2 lines
Quoted 2 lines

I tried that one (compared md5sum). It does not work. It only works for "ST31500341AS, 9JU138-300 or -336, SD15 through SD1A ONLY!"

Of course I did. They told me, my drives are not affected and drives with "good" serial numbers will not be upgraded.
And they now told me I have OEM drives (???) which they do not provide firmware upgrades for, although my drives are ok. I dont understand those support-people.

Well, they might be right. Or the drives may be affected but they don't support OEM versions anyway and may not know.

Obviously one could try updating anyway (I'm sure a simple hack in version/SN checking routine would do). It may be risky. You should, in theory, contact the OEM partner, not the manufacturer. Could be hard.

OTOH I think the update fixes unrelated problem (a drives failing to start), that would need checking.

Signature · 1 line
Krzysztof Halasa
#8 lore raw
In reply to Markus
Quoted 9 lines · Markus

Hello!

I have some Seagate Barracuda 7200.11 ST31500341AS 1.5TB drives. They use the firmware SD17. They time out at the flush write cache and sometimes on the identify command.
I know that sounds suspicious so I wrote to seagate but they told me my drives are ok. (Although I dont think so.)

This drive+fw is blacklisted in the kernel, but there is no firmware upgrade for these drives. (Only very few serial numbers are able to upgrade.)

Now I want to know after what period of the time the kernel timeouts at these commands!? And if this timeout can be increased (manually, small patch for the kernel) and the min/max/avg time could somehow be messured. Every timeout kicks the drives off the raid, so I disabled the write cache (hdparm -W0 /dev/sdx) but thats no solution, just a bad workaround.

I believe the timeout for commands like these is usually 30 seconds. Normally if it doesn't respond after that length of time, it never will. Even if it eventually did, I don't think you'd be happy with disk access delays of over 30 seconds..

Quoted 8 lines

Its a amd64 system with the 2.6.29.4 on an AM3 board with AMDs 790GX + SB750 Chipsets running in ahci mode.

Thanks for your time and support!

Markus

PS: Please CC me!

author
#9 lore raw
Quoted 2 lines · Robert Hancock
Quoted 1 line · Markus

Now I want to know after what period of the time the kernel timeouts

at

Quoted 1 line
Quoted 1 line

these commands!? And if this timeout can be increased (manually,

small

Quoted 3 lines
Quoted 3 lines

patch for the kernel) and the min/max/avg time could somehow be messured. Every timeout kicks the drives off the raid, so I disabled the write cache (hdparm -W0 /dev/sdx) but thats no solution, just a

bad

Quoted 4 lines
Quoted 1 line

workaround.

I believe the timeout for commands like these is usually 30 seconds. Normally if it doesn't respond after that length of time, it never

will.

Quoted 1 line

Even if it eventually did, I don't think you'd be happy with disk

access

Quoted 1 line

delays of over 30 seconds..

Ok thats definitly bad. Will reask at the support...

Markus