Two WinTV1110 in one PC not working, single works

DISCUSSION Tobias Kaminsky 1 participant 4 messages Jun 2, 2009 – Jun 5, 2009 Media (V4L/DVB)

lore

Share & tools

lore

Tobias Kaminsky

author

2009-06-02 13:58 UTC #0 lore raw

Hello,

I have two WinTX1110 installed in one PC:

04:03.0 Multimedia controller: Philips Semiconductors SAA7131/SAA7133/SAA7135 Video Broadcast Decoder (rev d1)
04:04.0 Multimedia controller: Philips Semiconductors SAA7131/SAA7133/SAA7135 Video Broadcast Decoder (rev d1)

The first card is working fine.
But the second fails to load the firmware:

[  215.424008] tda1004x: found firmware revision 0 -- invalid
[  215.424014] tda1004x: firmware upload failed

I have tried both cards alone in the pc and they are working, but together not.

The "first" card says this:

[  204.217357] tda1004x: found firmware revision 20 -- ok

So the current status is that only one is working and I do not know what I can change.

The Firmware:
-rw-r--r-- 1 root 24478 2008-10-27 06:33 /lib/firmware/dvb-fe-tda10046.fw

What else informations do you need?

Thank you very much!

Tobias Kaminsky

dmesg:

[   12.593302] Linux video capture interface: v2.00                                                                                          
[   12.903476] saa7130/34: v4l2 driver version 0.2.14 loaded                                                                                 
[   12.904699] saa7134 0000:04:03.0: PCI INT A -> GSI 16 (level, low) -> IRQ 
16                                                              
[   12.904706] saa7133[0]: found at 0000:04:03.0, rev: 209, irq: 16, latency: 
32, mmio: 0xfdaff000                                           
[   12.904714] saa7133[0]: subsystem: 0070:6701, board: Hauppauge WinTV-
HVR1110 DVB-T/Hybrid [card=104,autodetected]                         
[   12.904726] saa7133[0]: board init: gpio is 6400000                                                                                       
[   13.063355] saa7133[0]: i2c eeprom 00: 70 00 01 67 54 20 1c 00 43 43 a9 1c 
55 d2 b2 92                                                    
[   13.063366] saa7133[0]: i2c eeprom 10: ff ff ff 0e ff 20 ff ff ff ff ff ff ff ff ff ff                                                    
[   13.063375] saa7133[0]: i2c eeprom 20: 01 40 01 32 32 01 01 33 88 ff 00 aa ff 
ff ff ff                                                    
[   13.063383] saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff                                                    
[   13.063392] saa7133[0]: i2c eeprom 40: ff 21 00 c2 96 10 03 32 15 60 ff ff ff ff 
ff ff                                                    
[   13.063401] saa7133[0]: i2c eeprom 50: ff 00 00 00 00 00 00 00 00 00 00 00 
00 00 00 00                                                    
[   13.063409] saa7133[0]: i2c eeprom 60: 00 00 00 00 00 00 00 00 00 00 00 00 
00 00 00 00                                                    
[   13.063418] saa7133[0]: i2c eeprom 70: 00 00 00 00 00 00 00 00 00 00 00 00 
00 00 00 00                                                    
[   13.063426] saa7133[0]: i2c eeprom 80: 84 09 00 04 20 77 00 40 6f 78 0e f0 
73 05 29 00                                                    
[   13.063435] saa7133[0]: i2c eeprom 90: 84 08 00 06 cb 05 01 00 94 48 89 72 
07 70 73 09                                                    
[   13.063444] saa7133[0]: i2c eeprom a0: 23 5f 73 0a fc 72 72 0b 2f 72 0e 01 
72 0f 03 72                                                    
[   13.063452] saa7133[0]: i2c eeprom b0: 10 01 72 11 ff 79 49 00 00 00 00 00 
00 00 00 00                                                    
[   13.063461] saa7133[0]: i2c eeprom c0: 00 00 00 00 00 00 00 00 00 00 00 00 
00 00 00 00                                                    
[   13.063469] saa7133[0]: i2c eeprom d0: 00 00 00 00 00 00 00 00 00 00 00 00 
00 00 00 00                                                    
[   13.063478] saa7133[0]: i2c eeprom e0: 00 00 00 00 00 00 00 00 00 00 00 00 
00 00 00 00                                                    
[   13.063486] saa7133[0]: i2c eeprom f0: 00 00 00 00 00 00 00 00 00 00 00 00 
00 00 00 00                                                    
[   13.364324] tuner' 1-004b: chip found @ 0x96 (saa7133[0])                                                                                 
[   13.367371] tveeprom 1-0050: Hauppauge model 67019, rev B4B4, serial# 
948335                                                              
[   13.367375] tveeprom 1-0050: MAC address is 00-0D-FE-0E-78-6F                                                                             
[   13.367378] tveeprom 1-0050: tuner model is Philips 8275A (idx 114, type 4)                                                               
[   13.367381] tveeprom 1-0050: TV standards PAL(B/G) NTSC(M) PAL(I) 
SECAM(L/L') PAL(D/D1/K) ATSC/DVB Digital (eeprom 0xfc)                  
[   13.367385] tveeprom 1-0050: audio processor is SAA7131 (idx 41)                                                                          
[   13.367387] tveeprom 1-0050: decoder processor is SAA7131 (idx 35)                                                                        
[   13.367390] tveeprom 1-0050: has radio, has IR receiver, has IR transmitter                                                               
[   13.367392] saa7133[0]: hauppauge eeprom: model=67019                                                                                     
[   13.456094] tda829x 1-004b: setting tuner address to 61                                                                                   
[   13.556076] tda829x 1-004b: type set to tda8290+75a                                                                                       
[   17.422485] saa7133[0]: registered device video0 [v4l2]                                                                                   
[   17.422789] saa7133[0]: registered device vbi0                                                                                            
[   17.423087] saa7133[0]: registered device radio0                                                                                          
[   17.484044] saa7134 0000:04:04.0: PCI INT A -> GSI 17 (level, low) -> IRQ 
17                                                              
[   17.484052] saa7133[1]: found at 0000:04:04.0, rev: 209, irq: 17, latency: 
32, mmio: 0xfdafe000                                           
[   17.484060] saa7133[1]: subsystem: 0070:6701, board: Hauppauge WinTV-
HVR1110 DVB-T/Hybrid [card=104,autodetected]                         
[   17.484072] saa7133[1]: board init: gpio is 6400000                                                                                       
[   17.628082] tuner' 2-004b: chip found @ 0x96 (saa7133[1])                                                                                 
[   17.676014] saa7133[1]: i2c eeprom 00: 70 00 01 67 54 20 1c 00 43 43 a9 1c 
55 d2 b2 92                                                    
[   17.676024] saa7133[1]: i2c eeprom 10: ff ff ff 0e ff 20 ff ff ff ff ff ff ff ff ff ff                                                    
[   17.676033] saa7133[1]: i2c eeprom 20: 01 40 01 32 32 01 01 33 88 ff 00 aa ff 
ff ff ff                                                    
[   17.676042] saa7133[1]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff                                                    
[   17.676051] saa7133[1]: i2c eeprom 40: ff 21 00 c2 96 10 03 32 15 60 ff ff ff ff 
ff ff                                                    
[   17.676059] saa7133[1]: i2c eeprom 50: ff 00 00 00 00 00 00 00 00 00 00 00 
00 00 00 00                                                    
[   17.676068] saa7133[1]: i2c eeprom 60: 00 00 00 00 00 00 00 00 00 00 00 00 
00 00 00 00                                                    
[   17.676077] saa7133[1]: i2c eeprom 70: 00 00 00 00 00 00 00 00 00 00 00 00 
00 00 00 00                                                    
[   17.676085] saa7133[1]: i2c eeprom 80: 84 09 00 04 20 77 00 40 59 4b 4f f0 
73 05 29 00                                                    
[   17.676094] saa7133[1]: i2c eeprom 90: 84 08 00 06 cb 05 01 00 94 48 89 72 
07 70 73 09                                                    
[   17.676103] saa7133[1]: i2c eeprom a0: 23 5f 73 0a fc 72 72 0b 2f 72 0e 01 
72 0f 03 72                                                    
[   17.676111] saa7133[1]: i2c eeprom b0: 10 01 72 11 ff 79 4b 00 00 00 00 00 
00 00 00 00                                                    
[   17.676120] saa7133[1]: i2c eeprom c0: 00 00 00 00 00 00 00 00 00 00 00 00 
00 00 00 00                                                    
[   17.676128] saa7133[1]: i2c eeprom d0: 00 00 00 00 00 00 00 00 00 00 00 00 
00 00 00 00                                                    
[   17.676137] saa7133[1]: i2c eeprom e0: 00 00 00 00 00 00 00 00 00 00 00 00 
00 00 00 00                                                    
[   17.676146] saa7133[1]: i2c eeprom f0: 00 00 00 00 00 00 00 00 00 00 00 00 
00 00 00 00                                                    
[   17.685388] tveeprom 2-0050: Hauppauge model 67019, rev B4B4, serial# 
5196633                                                             
[   17.685392] tveeprom 2-0050: MAC address is 00-0D-FE-4F-4B-59                                                                             
[   17.685395] tveeprom 2-0050: tuner model is Philips 8275A (idx 114, type 4)                                                               
[   17.685398] tveeprom 2-0050: TV standards PAL(B/G) NTSC(M) PAL(I) 
SECAM(L/L') PAL(D/D1/K) ATSC/DVB Digital (eeprom 0xfc)                  
[   17.685402] tveeprom 2-0050: audio processor is SAA7131 (idx 41)                                                                          
[   17.685404] tveeprom 2-0050: decoder processor is SAA7131 (idx 35)                                                                        
[   17.685407] tveeprom 2-0050: has radio, has IR receiver, has IR transmitter                                                               
[   17.685410] saa7133[1]: hauppauge eeprom: model=67019                                                                                     
[   17.772015] tda829x 2-004b: setting tuner address to 61                                                                                   
[   17.836014] tda829x 2-004b: type set to tda8290+75a                                                                                       
[   21.692599] saa7133[1]: registered device video1 [v4l2]                                                                                   
[   21.692915] saa7133[1]: registered device vbi1                                                                                            
[   21.693223] saa7133[1]: registered device radio1                                                                                          
[   21.777372] saa7134 ALSA driver for DMA sound loaded                                                                                      
[   21.789059] saa7133[0]/alsa: saa7133[0] at 0xfdaff000 irq 16 registered as 
card -2                                                        
[   21.789550] saa7133[1]/alsa: saa7133[1] at 0xfdafe000 irq 17 registered as 
card -1                                                        
[   21.938693] DVB: registering new adapter (saa7133[0])                                                                                     
[   21.938698] DVB: registering frontend 0 (Philips TDA10046H DVB-T)...

Tobias Kaminsky

author

2009-06-02 14:33 UTC #1 lore raw

With a new firmware:
-rw-r--r-- 1 root 24479 2009-06-02 16:09 /lib/firmware/dvb-fe-tda10046.fw -rw-r--r-- 1 root 24478 2009-06-02 16:09 /lib/firmware/dvb-fe-tda10046.fw- backup-02-06-09

I get FE_HAS_LOCK on both cards, but

root@finswimmer-desktop:/lib/firmware# tzap -a 1 "ProSieben(ProSiebenSat.1)"
using '/dev/dvb/adapter1/frontend0' and '/dev/dvb/adapter1/demux0'
tuning to 738000000 Hz
video pid 0x0131, audio pid 0x0132
status 00 | signal 0000 | snr f6f6 | ber 0001fffe | unc 00000000 |
status 1f | signal 0000 | snr f6f6 | ber 0001fffe | unc 00000000 | FE_HAS_LOCK
status 1f | signal 0000 | snr f6f6 | ber 0001fffe | unc 00000000 | FE_HAS_LOCK
status 1f | signal 0000 | snr f6f6 | ber 0001fffe | unc 00000000 | FE_HAS_LOCK
status 1f | signal 0000 | snr f6f6 | ber 0001fffe | unc 00000000 | FE_HAS_LOCK

"ber" is always the same. Therefore there are no datas in dvr0.

Jun  2 16:11:30 finswimmer-desktop root: card0

Jun  2 16:11:33 finswimmer-desktop kernel: [ 6540.080006] tda1004x: setting up 
plls for 48MHz sampling clock                                 
Jun  2 16:11:33 finswimmer-desktop kernel: [ 6540.364007] tda1004x: found

firmware revision 20 -- ok

Jun  2 16:11:46 finswimmer-desktop root: card1

Jun  2 16:11:49 finswimmer-desktop kernel: [ 6556.044007] tda1004x: setting up 
plls for 48MHz sampling clock                                 
Jun  2 16:11:49 finswimmer-desktop kernel: [ 6556.712007] tda1004x: found 
firmware revision 0 -- invalid                                     
Jun  2 16:11:49 finswimmer-desktop kernel: [ 6556.712015] tda1004x: trying to 
boot from eeprom                                               
Jun  2 16:11:52 finswimmer-desktop kernel: [ 6559.080007] tda1004x: found 
firmware revision 0 -- invalid                                     
Jun  2 16:11:52 finswimmer-desktop kernel: [ 6559.080013] tda1004x: waiting for 
firmware upload...                                           
Jun  2 16:11:52 finswimmer-desktop kernel: [ 6559.080017] firmware: requesting 
dvb-fe-tda10046.fw                                            
Jun  2 16:12:06 finswimmer-desktop kernel: [ 6573.524007] tda1004x: found 
firmware revision ed -- invalid                                    
Jun  2 16:12:06 finswimmer-desktop kernel: [ 6573.524013] tda1004x: firmware 
upload failed                                                   
Jun  2 16:12:27 finswimmer-desktop kernel: [ 6594.332007] tda1004x: setting up 
plls for 48MHz sampling clock                                 
Jun  2 16:12:29 finswimmer-desktop kernel: [ 6596.616006] tda1004x: found 
firmware revision 0 -- invalid                                     
Jun  2 16:12:29 finswimmer-desktop kernel: [ 6596.616012] tda1004x: trying to 
boot from eeprom                                               
Jun  2 16:12:31 finswimmer-desktop kernel: [ 6598.984007] tda1004x: found 
firmware revision 0 -- invalid                                     
Jun  2 16:12:31 finswimmer-desktop kernel: [ 6598.984014] tda1004x: waiting for 
firmware upload...                                           
Jun  2 16:12:31 finswimmer-desktop kernel: [ 6598.984018] firmware: requesting 
dvb-fe-tda10046.fw                                            
Jun  2 16:12:46 finswimmer-desktop kernel: [ 6613.424007] tda1004x: found 
firmware revision ed -- invalid                                    
Jun  2 16:12:46 finswimmer-desktop kernel: [ 6613.424013] tda1004x: firmware

upload failed

Quoted 154 lines · On Tuesday 02 June 2009 15:57:27 Tobias Kaminsky wrote:

Hello,

I have two WinTX1110 installed in one PC:

04:03.0 Multimedia controller: Philips Semiconductors SAA7131/SAA7133/SAA7135 Video Broadcast Decoder (rev d1) 04:04.0 Multimedia controller: Philips Semiconductors SAA7131/SAA7133/SAA7135 Video Broadcast Decoder (rev d1)

The first card is working fine.
But the second fails to load the firmware:

[  215.424008] tda1004x: found firmware revision 0 -- invalid
[  215.424014] tda1004x: firmware upload failed

I have tried both cards alone in the pc and they are working, but together not.

The "first" card says this:

[  204.217357] tda1004x: found firmware revision 20 -- ok

So the current status is that only one is working and I do not know what I can change.

The Firmware:
-rw-r--r-- 1 root 24478 2008-10-27 06:33 /lib/firmware/dvb-fe-tda10046.fw

What else informations do you need?

Thank you very much!

Tobias Kaminsky

dmesg:

[   12.593302] Linux video capture interface: v2.00
[   12.903476] saa7130/34: v4l2 driver version 0.2.14 loaded
[   12.904699] saa7134 0000:04:03.0: PCI INT A -> GSI 16 (level, low) ->
IRQ 16
[   12.904706] saa7133[0]: found at 0000:04:03.0, rev: 209, irq: 16,
latency: 32, mmio: 0xfdaff000
[   12.904714] saa7133[0]: subsystem: 0070:6701, board: Hauppauge WinTV-
HVR1110 DVB-T/Hybrid [card=104,autodetected]
[   12.904726] saa7133[0]: board init: gpio is 6400000
[   13.063355] saa7133[0]: i2c eeprom 00: 70 00 01 67 54 20 1c 00 43 43 a9
1c 55 d2 b2 92
[   13.063366] saa7133[0]: i2c eeprom 10: ff ff ff 0e ff 20 ff ff ff ff ff
ff ff ff ff ff [   13.063375] saa7133[0]: i2c eeprom 20: 01 40 01 32 32 01
01 33 88 ff 00 aa ff ff ff ff
[   13.063383] saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff [   13.063392] saa7133[0]: i2c eeprom 40: ff 21 00 c2 96 10
03 32 15 60 ff ff ff ff ff ff
[   13.063401] saa7133[0]: i2c eeprom 50: ff 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00
[   13.063409] saa7133[0]: i2c eeprom 60: 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00
[   13.063418] saa7133[0]: i2c eeprom 70: 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00
[   13.063426] saa7133[0]: i2c eeprom 80: 84 09 00 04 20 77 00 40 6f 78 0e
f0 73 05 29 00
[   13.063435] saa7133[0]: i2c eeprom 90: 84 08 00 06 cb 05 01 00 94 48 89
72 07 70 73 09
[   13.063444] saa7133[0]: i2c eeprom a0: 23 5f 73 0a fc 72 72 0b 2f 72 0e
01 72 0f 03 72
[   13.063452] saa7133[0]: i2c eeprom b0: 10 01 72 11 ff 79 49 00 00 00 00
00 00 00 00 00
[   13.063461] saa7133[0]: i2c eeprom c0: 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00
[   13.063469] saa7133[0]: i2c eeprom d0: 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00
[   13.063478] saa7133[0]: i2c eeprom e0: 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00
[   13.063486] saa7133[0]: i2c eeprom f0: 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00
[   13.364324] tuner' 1-004b: chip found @ 0x96 (saa7133[0])
[   13.367371] tveeprom 1-0050: Hauppauge model 67019, rev B4B4, serial#
948335
[   13.367375] tveeprom 1-0050: MAC address is 00-0D-FE-0E-78-6F
[   13.367378] tveeprom 1-0050: tuner model is Philips 8275A (idx 114, type
4) [   13.367381] tveeprom 1-0050: TV standards PAL(B/G) NTSC(M) PAL(I)
SECAM(L/L') PAL(D/D1/K) ATSC/DVB Digital (eeprom 0xfc)
[   13.367385] tveeprom 1-0050: audio processor is SAA7131 (idx 41)
[   13.367387] tveeprom 1-0050: decoder processor is SAA7131 (idx 35)
[   13.367390] tveeprom 1-0050: has radio, has IR receiver, has IR
transmitter [   13.367392] saa7133[0]: hauppauge eeprom: model=67019
[   13.456094] tda829x 1-004b: setting tuner address to 61
[   13.556076] tda829x 1-004b: type set to tda8290+75a
[   17.422485] saa7133[0]: registered device video0 [v4l2]
[   17.422789] saa7133[0]: registered device vbi0
[   17.423087] saa7133[0]: registered device radio0
[   17.484044] saa7134 0000:04:04.0: PCI INT A -> GSI 17 (level, low) ->
IRQ 17
[   17.484052] saa7133[1]: found at 0000:04:04.0, rev: 209, irq: 17,
latency: 32, mmio: 0xfdafe000
[   17.484060] saa7133[1]: subsystem: 0070:6701, board: Hauppauge WinTV-
HVR1110 DVB-T/Hybrid [card=104,autodetected]
[   17.484072] saa7133[1]: board init: gpio is 6400000
[   17.628082] tuner' 2-004b: chip found @ 0x96 (saa7133[1])
[   17.676014] saa7133[1]: i2c eeprom 00: 70 00 01 67 54 20 1c 00 43 43 a9
1c 55 d2 b2 92
[   17.676024] saa7133[1]: i2c eeprom 10: ff ff ff 0e ff 20 ff ff ff ff ff
ff ff ff ff ff [   17.676033] saa7133[1]: i2c eeprom 20: 01 40 01 32 32 01
01 33 88 ff 00 aa ff ff ff ff
[   17.676042] saa7133[1]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff [   17.676051] saa7133[1]: i2c eeprom 40: ff 21 00 c2 96 10
03 32 15 60 ff ff ff ff ff ff
[   17.676059] saa7133[1]: i2c eeprom 50: ff 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00
[   17.676068] saa7133[1]: i2c eeprom 60: 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00
[   17.676077] saa7133[1]: i2c eeprom 70: 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00
[   17.676085] saa7133[1]: i2c eeprom 80: 84 09 00 04 20 77 00 40 59 4b 4f
f0 73 05 29 00
[   17.676094] saa7133[1]: i2c eeprom 90: 84 08 00 06 cb 05 01 00 94 48 89
72 07 70 73 09
[   17.676103] saa7133[1]: i2c eeprom a0: 23 5f 73 0a fc 72 72 0b 2f 72 0e
01 72 0f 03 72
[   17.676111] saa7133[1]: i2c eeprom b0: 10 01 72 11 ff 79 4b 00 00 00 00
00 00 00 00 00
[   17.676120] saa7133[1]: i2c eeprom c0: 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00
[   17.676128] saa7133[1]: i2c eeprom d0: 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00
[   17.676137] saa7133[1]: i2c eeprom e0: 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00
[   17.676146] saa7133[1]: i2c eeprom f0: 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00
[   17.685388] tveeprom 2-0050: Hauppauge model 67019, rev B4B4, serial#
5196633
[   17.685392] tveeprom 2-0050: MAC address is 00-0D-FE-4F-4B-59
[   17.685395] tveeprom 2-0050: tuner model is Philips 8275A (idx 114, type
4) [   17.685398] tveeprom 2-0050: TV standards PAL(B/G) NTSC(M) PAL(I)
SECAM(L/L') PAL(D/D1/K) ATSC/DVB Digital (eeprom 0xfc)
[   17.685402] tveeprom 2-0050: audio processor is SAA7131 (idx 41)
[   17.685404] tveeprom 2-0050: decoder processor is SAA7131 (idx 35)
[   17.685407] tveeprom 2-0050: has radio, has IR receiver, has IR
transmitter [   17.685410] saa7133[1]: hauppauge eeprom: model=67019
[   17.772015] tda829x 2-004b: setting tuner address to 61
[   17.836014] tda829x 2-004b: type set to tda8290+75a
[   21.692599] saa7133[1]: registered device video1 [v4l2]
[   21.692915] saa7133[1]: registered device vbi1
[   21.693223] saa7133[1]: registered device radio1
[   21.777372] saa7134 ALSA driver for DMA sound loaded
[   21.789059] saa7133[0]/alsa: saa7133[0] at 0xfdaff000 irq 16 registered
as card -2
[   21.789550] saa7133[1]/alsa: saa7133[1] at 0xfdafe000 irq 17 registered
as card -1
[   21.938693] DVB: registering new adapter (saa7133[0])
[   21.938698] DVB: registering frontend 0 (Philips TDA10046H DVB-T)...

--
To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html

Tobias Kaminsky

author

2009-06-04 12:31 UTC #2 lore raw

Hello,

this is what I figured out.
If I am using the newest v4l-hg:
1) make install --> coldboot --> both card works --> coldboot --> just one card works
2) make install --> init 0 (not powering completly off) --> just one card works
3) make install --> init 6 --> both card works

Please let me know what informations do you need!

Thank you!

Tobias Kaminsky

Quoted 225 lines · On Tuesday 02 June 2009 16:32:43 Tobias Kaminsky wrote:

With a new firmware:

(quoted diff) +0 -2

-rw-r--r-- 1 root 24479 2009-06-02 16:09 /lib/firmware/dvb-fe-tda10046.fw
-rw-r--r-- 1 root 24478 2009-06-02 16:09 /lib/firmware/dvb-fe-tda10046.fw-

backup-02-06-09

I get FE_HAS_LOCK on both cards, but

root@finswimmer-desktop:/lib/firmware# tzap -a 1
"ProSieben(ProSiebenSat.1)" using '/dev/dvb/adapter1/frontend0' and
'/dev/dvb/adapter1/demux0' tuning to 738000000 Hz
video pid 0x0131, audio pid 0x0132
status 00 | signal 0000 | snr f6f6 | ber 0001fffe | unc 00000000 |
status 1f | signal 0000 | snr f6f6 | ber 0001fffe | unc 00000000 |
FE_HAS_LOCK status 1f | signal 0000 | snr f6f6 | ber 0001fffe | unc
00000000 | FE_HAS_LOCK status 1f | signal 0000 | snr f6f6 | ber 0001fffe |
unc 00000000 | FE_HAS_LOCK status 1f | signal 0000 | snr f6f6 | ber
0001fffe | unc 00000000 | FE_HAS_LOCK

"ber" is always the same. Therefore there are no datas in dvr0.

Jun  2 16:11:30 finswimmer-desktop root: card0

Jun  2 16:11:33 finswimmer-desktop kernel: [ 6540.080006] tda1004x: setting
up plls for 48MHz sampling clock
Jun  2 16:11:33 finswimmer-desktop kernel: [ 6540.364007] tda1004x: found

firmware revision 20 -- ok

Jun  2 16:11:46 finswimmer-desktop root: card1

Jun  2 16:11:49 finswimmer-desktop kernel: [ 6556.044007] tda1004x: setting
up plls for 48MHz sampling clock
Jun  2 16:11:49 finswimmer-desktop kernel: [ 6556.712007] tda1004x: found
firmware revision 0 -- invalid
Jun  2 16:11:49 finswimmer-desktop kernel: [ 6556.712015] tda1004x: trying
to boot from eeprom
Jun  2 16:11:52 finswimmer-desktop kernel: [ 6559.080007] tda1004x: found
firmware revision 0 -- invalid
Jun  2 16:11:52 finswimmer-desktop kernel: [ 6559.080013] tda1004x: waiting
for firmware upload...
Jun  2 16:11:52 finswimmer-desktop kernel: [ 6559.080017] firmware:
requesting dvb-fe-tda10046.fw
Jun  2 16:12:06 finswimmer-desktop kernel: [ 6573.524007] tda1004x: found
firmware revision ed -- invalid
Jun  2 16:12:06 finswimmer-desktop kernel: [ 6573.524013] tda1004x:
firmware upload failed
Jun  2 16:12:27 finswimmer-desktop kernel: [ 6594.332007] tda1004x: setting
up plls for 48MHz sampling clock
Jun  2 16:12:29 finswimmer-desktop kernel: [ 6596.616006] tda1004x: found
firmware revision 0 -- invalid
Jun  2 16:12:29 finswimmer-desktop kernel: [ 6596.616012] tda1004x: trying
to boot from eeprom
Jun  2 16:12:31 finswimmer-desktop kernel: [ 6598.984007] tda1004x: found
firmware revision 0 -- invalid
Jun  2 16:12:31 finswimmer-desktop kernel: [ 6598.984014] tda1004x: waiting
for firmware upload...
Jun  2 16:12:31 finswimmer-desktop kernel: [ 6598.984018] firmware:
requesting dvb-fe-tda10046.fw
Jun  2 16:12:46 finswimmer-desktop kernel: [ 6613.424007] tda1004x: found
firmware revision ed -- invalid
Jun  2 16:12:46 finswimmer-desktop kernel: [ 6613.424013] tda1004x:

firmware upload failed

Quoted 150 lines · On Tuesday 02 June 2009 15:57:27 Tobias Kaminsky wrote:

Hello,

I have two WinTX1110 installed in one PC:

04:03.0 Multimedia controller: Philips Semiconductors SAA7131/SAA7133/SAA7135 Video Broadcast Decoder (rev d1) 04:04.0 Multimedia controller: Philips Semiconductors SAA7131/SAA7133/SAA7135 Video Broadcast Decoder (rev d1)

The first card is working fine.
But the second fails to load the firmware:

[  215.424008] tda1004x: found firmware revision 0 -- invalid
[  215.424014] tda1004x: firmware upload failed

I have tried both cards alone in the pc and they are working, but together not.

The "first" card says this:

[  204.217357] tda1004x: found firmware revision 20 -- ok

So the current status is that only one is working and I do not know what I can change.

The Firmware:
-rw-r--r-- 1 root 24478 2008-10-27 06:33 /lib/firmware/dvb-fe-tda10046.fw

What else informations do you need?

Thank you very much!

Tobias Kaminsky

dmesg:

[   12.593302] Linux video capture interface: v2.00
[   12.903476] saa7130/34: v4l2 driver version 0.2.14 loaded
[   12.904699] saa7134 0000:04:03.0: PCI INT A -> GSI 16 (level, low) ->
IRQ 16
[   12.904706] saa7133[0]: found at 0000:04:03.0, rev: 209, irq: 16,
latency: 32, mmio: 0xfdaff000
[   12.904714] saa7133[0]: subsystem: 0070:6701, board: Hauppauge WinTV-
HVR1110 DVB-T/Hybrid [card=104,autodetected]
[   12.904726] saa7133[0]: board init: gpio is 6400000
[   13.063355] saa7133[0]: i2c eeprom 00: 70 00 01 67 54 20 1c 00 43 43
a9 1c 55 d2 b2 92
[   13.063366] saa7133[0]: i2c eeprom 10: ff ff ff 0e ff 20 ff ff ff ff
ff ff ff ff ff ff [   13.063375] saa7133[0]: i2c eeprom 20: 01 40 01 32
32 01 01 33 88 ff 00 aa ff ff ff ff
[   13.063383] saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff ff [   13.063392] saa7133[0]: i2c eeprom 40: ff 21 00 c2
96 10 03 32 15 60 ff ff ff ff ff ff
[   13.063401] saa7133[0]: i2c eeprom 50: ff 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00
[   13.063409] saa7133[0]: i2c eeprom 60: 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00
[   13.063418] saa7133[0]: i2c eeprom 70: 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00
[   13.063426] saa7133[0]: i2c eeprom 80: 84 09 00 04 20 77 00 40 6f 78
0e f0 73 05 29 00
[   13.063435] saa7133[0]: i2c eeprom 90: 84 08 00 06 cb 05 01 00 94 48
89 72 07 70 73 09
[   13.063444] saa7133[0]: i2c eeprom a0: 23 5f 73 0a fc 72 72 0b 2f 72
0e 01 72 0f 03 72
[   13.063452] saa7133[0]: i2c eeprom b0: 10 01 72 11 ff 79 49 00 00 00
00 00 00 00 00 00
[   13.063461] saa7133[0]: i2c eeprom c0: 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00
[   13.063469] saa7133[0]: i2c eeprom d0: 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00
[   13.063478] saa7133[0]: i2c eeprom e0: 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00
[   13.063486] saa7133[0]: i2c eeprom f0: 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00
[   13.364324] tuner' 1-004b: chip found @ 0x96 (saa7133[0])
[   13.367371] tveeprom 1-0050: Hauppauge model 67019, rev B4B4, serial#
948335
[   13.367375] tveeprom 1-0050: MAC address is 00-0D-FE-0E-78-6F
[   13.367378] tveeprom 1-0050: tuner model is Philips 8275A (idx 114,
type 4) [   13.367381] tveeprom 1-0050: TV standards PAL(B/G) NTSC(M)
PAL(I) SECAM(L/L') PAL(D/D1/K) ATSC/DVB Digital (eeprom 0xfc)
[   13.367385] tveeprom 1-0050: audio processor is SAA7131 (idx 41)
[   13.367387] tveeprom 1-0050: decoder processor is SAA7131 (idx 35)
[   13.367390] tveeprom 1-0050: has radio, has IR receiver, has IR
transmitter [   13.367392] saa7133[0]: hauppauge eeprom: model=67019
[   13.456094] tda829x 1-004b: setting tuner address to 61
[   13.556076] tda829x 1-004b: type set to tda8290+75a
[   17.422485] saa7133[0]: registered device video0 [v4l2]
[   17.422789] saa7133[0]: registered device vbi0
[   17.423087] saa7133[0]: registered device radio0
[   17.484044] saa7134 0000:04:04.0: PCI INT A -> GSI 17 (level, low) ->
IRQ 17
[   17.484052] saa7133[1]: found at 0000:04:04.0, rev: 209, irq: 17,
latency: 32, mmio: 0xfdafe000
[   17.484060] saa7133[1]: subsystem: 0070:6701, board: Hauppauge WinTV-
HVR1110 DVB-T/Hybrid [card=104,autodetected]
[   17.484072] saa7133[1]: board init: gpio is 6400000
[   17.628082] tuner' 2-004b: chip found @ 0x96 (saa7133[1])
[   17.676014] saa7133[1]: i2c eeprom 00: 70 00 01 67 54 20 1c 00 43 43
a9 1c 55 d2 b2 92
[   17.676024] saa7133[1]: i2c eeprom 10: ff ff ff 0e ff 20 ff ff ff ff
ff ff ff ff ff ff [   17.676033] saa7133[1]: i2c eeprom 20: 01 40 01 32
32 01 01 33 88 ff 00 aa ff ff ff ff
[   17.676042] saa7133[1]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff ff [   17.676051] saa7133[1]: i2c eeprom 40: ff 21 00 c2
96 10 03 32 15 60 ff ff ff ff ff ff
[   17.676059] saa7133[1]: i2c eeprom 50: ff 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00
[   17.676068] saa7133[1]: i2c eeprom 60: 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00
[   17.676077] saa7133[1]: i2c eeprom 70: 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00
[   17.676085] saa7133[1]: i2c eeprom 80: 84 09 00 04 20 77 00 40 59 4b
4f f0 73 05 29 00
[   17.676094] saa7133[1]: i2c eeprom 90: 84 08 00 06 cb 05 01 00 94 48
89 72 07 70 73 09
[   17.676103] saa7133[1]: i2c eeprom a0: 23 5f 73 0a fc 72 72 0b 2f 72
0e 01 72 0f 03 72
[   17.676111] saa7133[1]: i2c eeprom b0: 10 01 72 11 ff 79 4b 00 00 00
00 00 00 00 00 00
[   17.676120] saa7133[1]: i2c eeprom c0: 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00
[   17.676128] saa7133[1]: i2c eeprom d0: 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00
[   17.676137] saa7133[1]: i2c eeprom e0: 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00
[   17.676146] saa7133[1]: i2c eeprom f0: 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00
[   17.685388] tveeprom 2-0050: Hauppauge model 67019, rev B4B4, serial#
5196633
[   17.685392] tveeprom 2-0050: MAC address is 00-0D-FE-4F-4B-59
[   17.685395] tveeprom 2-0050: tuner model is Philips 8275A (idx 114,
type 4) [   17.685398] tveeprom 2-0050: TV standards PAL(B/G) NTSC(M)
PAL(I) SECAM(L/L') PAL(D/D1/K) ATSC/DVB Digital (eeprom 0xfc)
[   17.685402] tveeprom 2-0050: audio processor is SAA7131 (idx 41)
[   17.685404] tveeprom 2-0050: decoder processor is SAA7131 (idx 35)
[   17.685407] tveeprom 2-0050: has radio, has IR receiver, has IR
transmitter [   17.685410] saa7133[1]: hauppauge eeprom: model=67019
[   17.772015] tda829x 2-004b: setting tuner address to 61
[   17.836014] tda829x 2-004b: type set to tda8290+75a
[   21.692599] saa7133[1]: registered device video1 [v4l2]
[   21.692915] saa7133[1]: registered device vbi1
[   21.693223] saa7133[1]: registered device radio1
[   21.777372] saa7134 ALSA driver for DMA sound loaded
[   21.789059] saa7133[0]/alsa: saa7133[0] at 0xfdaff000 irq 16
registered as card -2
[   21.789550] saa7133[1]/alsa: saa7133[1] at 0xfdafe000 irq 17
registered as card -1
[   21.938693] DVB: registering new adapter (saa7133[0])
[   21.938698] DVB: registering frontend 0 (Philips TDA10046H DVB-T)...

Quoted 4 lines

--
To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html

--
To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html

Tobias Kaminsky

author

2009-06-05 12:56 UTC #3 lore raw

Just for the record.
Using a self compiled kernel under mythbuntu solved the problems.

Tobi

Quoted 243 lines · On Thursday 04 June 2009 14:31:15 you wrote:

Hello,

Please let me know what informations do you need!

Thank you!

Tobias Kaminsky

Quoted 226 lines · On Tuesday 02 June 2009 16:32:43 Tobias Kaminsky wrote:

With a new firmware:

(quoted diff) +0 -2

-rw-r--r-- 1 root 24479 2009-06-02 16:09 /lib/firmware/dvb-fe-tda10046.fw
-rw-r--r-- 1 root 24478 2009-06-02 16:09

/lib/firmware/dvb-fe-tda10046.fw- backup-02-06-09

I get FE_HAS_LOCK on both cards, but

root@finswimmer-desktop:/lib/firmware# tzap -a 1
"ProSieben(ProSiebenSat.1)" using '/dev/dvb/adapter1/frontend0' and
'/dev/dvb/adapter1/demux0' tuning to 738000000 Hz
video pid 0x0131, audio pid 0x0132
status 00 | signal 0000 | snr f6f6 | ber 0001fffe | unc 00000000 |
status 1f | signal 0000 | snr f6f6 | ber 0001fffe | unc 00000000 |
FE_HAS_LOCK status 1f | signal 0000 | snr f6f6 | ber 0001fffe | unc
00000000 | FE_HAS_LOCK status 1f | signal 0000 | snr f6f6 | ber 0001fffe
| unc 00000000 | FE_HAS_LOCK status 1f | signal 0000 | snr f6f6 | ber
0001fffe | unc 00000000 | FE_HAS_LOCK

"ber" is always the same. Therefore there are no datas in dvr0.

Jun  2 16:11:30 finswimmer-desktop root: card0

Jun  2 16:11:33 finswimmer-desktop kernel: [ 6540.080006] tda1004x:
setting up plls for 48MHz sampling clock
Jun  2 16:11:33 finswimmer-desktop kernel: [ 6540.364007] tda1004x: found

firmware revision 20 -- ok

Jun  2 16:11:46 finswimmer-desktop root: card1

Jun  2 16:11:49 finswimmer-desktop kernel: [ 6556.044007] tda1004x:
setting up plls for 48MHz sampling clock
Jun  2 16:11:49 finswimmer-desktop kernel: [ 6556.712007] tda1004x: found
firmware revision 0 -- invalid
Jun  2 16:11:49 finswimmer-desktop kernel: [ 6556.712015] tda1004x:
trying to boot from eeprom
Jun  2 16:11:52 finswimmer-desktop kernel: [ 6559.080007] tda1004x: found
firmware revision 0 -- invalid
Jun  2 16:11:52 finswimmer-desktop kernel: [ 6559.080013] tda1004x:
waiting for firmware upload...
Jun  2 16:11:52 finswimmer-desktop kernel: [ 6559.080017] firmware:
requesting dvb-fe-tda10046.fw
Jun  2 16:12:06 finswimmer-desktop kernel: [ 6573.524007] tda1004x: found
firmware revision ed -- invalid
Jun  2 16:12:06 finswimmer-desktop kernel: [ 6573.524013] tda1004x:
firmware upload failed
Jun  2 16:12:27 finswimmer-desktop kernel: [ 6594.332007] tda1004x:
setting up plls for 48MHz sampling clock
Jun  2 16:12:29 finswimmer-desktop kernel: [ 6596.616006] tda1004x: found
firmware revision 0 -- invalid
Jun  2 16:12:29 finswimmer-desktop kernel: [ 6596.616012] tda1004x:
trying to boot from eeprom
Jun  2 16:12:31 finswimmer-desktop kernel: [ 6598.984007] tda1004x: found
firmware revision 0 -- invalid
Jun  2 16:12:31 finswimmer-desktop kernel: [ 6598.984014] tda1004x:
waiting for firmware upload...
Jun  2 16:12:31 finswimmer-desktop kernel: [ 6598.984018] firmware:
requesting dvb-fe-tda10046.fw
Jun  2 16:12:46 finswimmer-desktop kernel: [ 6613.424007] tda1004x: found
firmware revision ed -- invalid
Jun  2 16:12:46 finswimmer-desktop kernel: [ 6613.424013] tda1004x:

firmware upload failed

Quoted 151 lines · On Tuesday 02 June 2009 15:57:27 Tobias Kaminsky wrote:

Hello,

I have two WinTX1110 installed in one PC:

04:03.0 Multimedia controller: Philips Semiconductors SAA7131/SAA7133/SAA7135 Video Broadcast Decoder (rev d1) 04:04.0 Multimedia controller: Philips Semiconductors SAA7131/SAA7133/SAA7135 Video Broadcast Decoder (rev d1)

The first card is working fine.
But the second fails to load the firmware:

[  215.424008] tda1004x: found firmware revision 0 -- invalid
[  215.424014] tda1004x: firmware upload failed

I have tried both cards alone in the pc and they are working, but together not.

The "first" card says this:

[  204.217357] tda1004x: found firmware revision 20 -- ok

So the current status is that only one is working and I do not know what I can change.

The Firmware:
-rw-r--r-- 1 root 24478 2008-10-27 06:33
/lib/firmware/dvb-fe-tda10046.fw

What else informations do you need?

Thank you very much!

Tobias Kaminsky

dmesg:

[   12.593302] Linux video capture interface: v2.00
[   12.903476] saa7130/34: v4l2 driver version 0.2.14 loaded
[   12.904699] saa7134 0000:04:03.0: PCI INT A -> GSI 16 (level, low)
-> IRQ 16
[   12.904706] saa7133[0]: found at 0000:04:03.0, rev: 209, irq: 16,
latency: 32, mmio: 0xfdaff000
[   12.904714] saa7133[0]: subsystem: 0070:6701, board: Hauppauge
WinTV- HVR1110 DVB-T/Hybrid [card=104,autodetected]
[   12.904726] saa7133[0]: board init: gpio is 6400000
[   13.063355] saa7133[0]: i2c eeprom 00: 70 00 01 67 54 20 1c 00 43 43
a9 1c 55 d2 b2 92
[   13.063366] saa7133[0]: i2c eeprom 10: ff ff ff 0e ff 20 ff ff ff ff
ff ff ff ff ff ff [   13.063375] saa7133[0]: i2c eeprom 20: 01 40 01 32
32 01 01 33 88 ff 00 aa ff ff ff ff
[   13.063383] saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff ff [   13.063392] saa7133[0]: i2c eeprom 40: ff 21 00 c2
96 10 03 32 15 60 ff ff ff ff ff ff
[   13.063401] saa7133[0]: i2c eeprom 50: ff 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00
[   13.063409] saa7133[0]: i2c eeprom 60: 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00
[   13.063418] saa7133[0]: i2c eeprom 70: 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00
[   13.063426] saa7133[0]: i2c eeprom 80: 84 09 00 04 20 77 00 40 6f 78
0e f0 73 05 29 00
[   13.063435] saa7133[0]: i2c eeprom 90: 84 08 00 06 cb 05 01 00 94 48
89 72 07 70 73 09
[   13.063444] saa7133[0]: i2c eeprom a0: 23 5f 73 0a fc 72 72 0b 2f 72
0e 01 72 0f 03 72
[   13.063452] saa7133[0]: i2c eeprom b0: 10 01 72 11 ff 79 49 00 00 00
00 00 00 00 00 00
[   13.063461] saa7133[0]: i2c eeprom c0: 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00
[   13.063469] saa7133[0]: i2c eeprom d0: 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00
[   13.063478] saa7133[0]: i2c eeprom e0: 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00
[   13.063486] saa7133[0]: i2c eeprom f0: 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00
[   13.364324] tuner' 1-004b: chip found @ 0x96 (saa7133[0])
[   13.367371] tveeprom 1-0050: Hauppauge model 67019, rev B4B4,
serial# 948335
[   13.367375] tveeprom 1-0050: MAC address is 00-0D-FE-0E-78-6F
[   13.367378] tveeprom 1-0050: tuner model is Philips 8275A (idx 114,
type 4) [   13.367381] tveeprom 1-0050: TV standards PAL(B/G) NTSC(M)
PAL(I) SECAM(L/L') PAL(D/D1/K) ATSC/DVB Digital (eeprom 0xfc)
[   13.367385] tveeprom 1-0050: audio processor is SAA7131 (idx 41)
[   13.367387] tveeprom 1-0050: decoder processor is SAA7131 (idx 35)
[   13.367390] tveeprom 1-0050: has radio, has IR receiver, has IR
transmitter [   13.367392] saa7133[0]: hauppauge eeprom: model=67019
[   13.456094] tda829x 1-004b: setting tuner address to 61
[   13.556076] tda829x 1-004b: type set to tda8290+75a
[   17.422485] saa7133[0]: registered device video0 [v4l2]
[   17.422789] saa7133[0]: registered device vbi0
[   17.423087] saa7133[0]: registered device radio0
[   17.484044] saa7134 0000:04:04.0: PCI INT A -> GSI 17 (level, low)
-> IRQ 17
[   17.484052] saa7133[1]: found at 0000:04:04.0, rev: 209, irq: 17,
latency: 32, mmio: 0xfdafe000
[   17.484060] saa7133[1]: subsystem: 0070:6701, board: Hauppauge
WinTV- HVR1110 DVB-T/Hybrid [card=104,autodetected]
[   17.484072] saa7133[1]: board init: gpio is 6400000
[   17.628082] tuner' 2-004b: chip found @ 0x96 (saa7133[1])
[   17.676014] saa7133[1]: i2c eeprom 00: 70 00 01 67 54 20 1c 00 43 43
a9 1c 55 d2 b2 92
[   17.676024] saa7133[1]: i2c eeprom 10: ff ff ff 0e ff 20 ff ff ff ff
ff ff ff ff ff ff [   17.676033] saa7133[1]: i2c eeprom 20: 01 40 01 32
32 01 01 33 88 ff 00 aa ff ff ff ff
[   17.676042] saa7133[1]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff ff [   17.676051] saa7133[1]: i2c eeprom 40: ff 21 00 c2
96 10 03 32 15 60 ff ff ff ff ff ff
[   17.676059] saa7133[1]: i2c eeprom 50: ff 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00
[   17.676068] saa7133[1]: i2c eeprom 60: 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00
[   17.676077] saa7133[1]: i2c eeprom 70: 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00
[   17.676085] saa7133[1]: i2c eeprom 80: 84 09 00 04 20 77 00 40 59 4b
4f f0 73 05 29 00
[   17.676094] saa7133[1]: i2c eeprom 90: 84 08 00 06 cb 05 01 00 94 48
89 72 07 70 73 09
[   17.676103] saa7133[1]: i2c eeprom a0: 23 5f 73 0a fc 72 72 0b 2f 72
0e 01 72 0f 03 72
[   17.676111] saa7133[1]: i2c eeprom b0: 10 01 72 11 ff 79 4b 00 00 00
00 00 00 00 00 00
[   17.676120] saa7133[1]: i2c eeprom c0: 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00
[   17.676128] saa7133[1]: i2c eeprom d0: 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00
[   17.676137] saa7133[1]: i2c eeprom e0: 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00
[   17.676146] saa7133[1]: i2c eeprom f0: 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00
[   17.685388] tveeprom 2-0050: Hauppauge model 67019, rev B4B4,
serial# 5196633
[   17.685392] tveeprom 2-0050: MAC address is 00-0D-FE-4F-4B-59
[   17.685395] tveeprom 2-0050: tuner model is Philips 8275A (idx 114,
type 4) [   17.685398] tveeprom 2-0050: TV standards PAL(B/G) NTSC(M)
PAL(I) SECAM(L/L') PAL(D/D1/K) ATSC/DVB Digital (eeprom 0xfc)
[   17.685402] tveeprom 2-0050: audio processor is SAA7131 (idx 41)
[   17.685404] tveeprom 2-0050: decoder processor is SAA7131 (idx 35)
[   17.685407] tveeprom 2-0050: has radio, has IR receiver, has IR
transmitter [   17.685410] saa7133[1]: hauppauge eeprom: model=67019
[   17.772015] tda829x 2-004b: setting tuner address to 61
[   17.836014] tda829x 2-004b: type set to tda8290+75a
[   21.692599] saa7133[1]: registered device video1 [v4l2]
[   21.692915] saa7133[1]: registered device vbi1
[   21.693223] saa7133[1]: registered device radio1
[   21.777372] saa7134 ALSA driver for DMA sound loaded
[   21.789059] saa7133[0]/alsa: saa7133[0] at 0xfdaff000 irq 16
registered as card -2
[   21.789550] saa7133[1]/alsa: saa7133[1] at 0xfdafe000 irq 17
registered as card -1
[   21.938693] DVB: registering new adapter (saa7133[0])
[   21.938698] DVB: registering frontend 0 (Philips TDA10046H DVB-T)...

Quoted 4 lines

--
To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html

--
To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html