board support patch for phyCORE-MPC5200B-tiny
PATCH v6 1/1 board support patch for phyCORE-MPC5200B-tiny
Add support for the Phytec phyCORE-MPC5200B-tiny. Code originally from Pengutronix.de. Created CONFIG_SYS_ATA_CS_ON_TIMER01 define for when IDE CS is on Timer 0/1
--- MAINTAINERS | 4 MAKEALL | 1 Makefile | 9 + board/phytec/pcm030/Makefile | 50 ++++ board/phytec/pcm030/config.mk | 41 +++ board/phytec/pcm030/mt46v32m16-75.h | 37 +++ board/phytec/pcm030/pcm030.c | 220 +++++++++++++++++ cpu/mpc5xxx/ide.c | 3 doc/README.phytec.pcm030 | 46 ++++ include/configs/pcm030.h | 444 +++++++++++++++++++++++++++++++++++ 10 files changed, 855 insertions(+), 0 deletions(-) create mode 100644 board/phytec/pcm030/Makefile create mode 100644 board/phytec/pcm030/config.mk create mode 100644 board/phytec/pcm030/mt46v32m16-75.h create mode 100644 board/phytec/pcm030/pcm030.c create mode 100644 doc/README.phytec.pcm030 create mode 100644 include/configs/pcm030.h
MAINTAINERS +4 -0
@@ -409,6 +409,10 @@ Andre Schwarz <[email protected]> mvbc_p MPC5200 mvblm7 MPC8343 +Jon Smirl <[email protected]> + + pcm030 MPC5200 + Timur Tabi <[email protected]> MPC8349E-mITX MPC8349
MAKEALL +1 -0
@@ -60,6 +60,7 @@ LIST_5xxx=" \ munices \ MVBC_P \ o2dnt \ + pcm030 \ pf5200 \ PM520 \ TB5200 \
Makefile +9 -0
@@ -696,6 +696,15 @@ MVBC_P_config: unconfig o2dnt_config: unconfig @$(MKCONFIG) o2dnt ppc mpc5xxx o2dnt +pcm030_config \ +pcm030_LOWBOOT_config: unconfig + @ >include/config.h + @[ -z "$(findstring LOWBOOT_,$@)" ] || \ + { echo "TEXT_BASE = 0xFF000000" >$(obj)board/phytec/pcm030/config.tmp ; \ + echo "... with LOWBOOT configuration" ; \ + } + @$(MKCONFIG) -a pcm030 ppc mpc5xxx pcm030 phytec + pf5200_config: unconfig @$(MKCONFIG) pf5200 ppc mpc5xxx pf5200 esd
board/phytec/pcm030/Makefile new file +50 -0
50 lines not on this page · raw message
board/phytec/pcm030/config.mk new file +41 -0
41 lines not on this page · raw message
board/phytec/pcm030/mt46v32m16-75.h new file +37 -0
@@ -0,0 +1,37 @@ +/* +* (C) Copyright 2004 +* Mark Jonas, Freescale Semiconductor, mark.jonas at motorola.com. +* +* Eric Schumann, Phytec Messtechnik +* adapted for mt46v32m16-75 DDR-RAM +* +* See file CREDITS for list of people who contributed to this +* project. +* +* This program is free software; you can redistribute it and/or +* modify it under the terms of the GNU General Public License as +* published by the Free Software Foundation; either version 2 of +* the License, or (at your option) any later version. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +* GNU General Public License for more details. +* +* You should have received a copy of the GNU General Public License +* along with this program; if not, write to the Free Software +* Foundation, Inc., 59 Temple Place, Suite 330, Boston, +* MA 02111-1307 USA +*/ + +#define SDRAM_DDR 1/* is DDR */ + +/* Settings for XLB = 132 MHz */ + +#define SDRAM_MODE 0x018D0000 +#define SDRAM_EMODE 0x40090000 +#define SDRAM_CONTROL 0x71500F00 +#define SDRAM_CONFIG1 0x73711930 +#define SDRAM_CONFIG2 0x47770000 + +#define SDRAM_TAPDELAY 0x10000000/* reserved Bit in MPC5200 B3-Step */
board/phytec/pcm030/pcm030.c new file +220 -0
220 lines not on this page · raw message
cpu/mpc5xxx/ide.c +3 -0
@@ -45,6 +45,9 @@ int ide_preinit (void)#if defined(CONFIG_SYS_ATA_CS_ON_I2C2 )/* ATA cs0/1 on i2c2 clk/io */ reg = (reg & ~0x03000000ul ) |0x02000000ul ; +#elif defined(CONFIG_SYS_ATA_CS_ON_TIMER01 ) +/* ATA cs0/1 on Timer 0/1 */ + reg = (reg & ~0x03000000ul ) |0x03000000ul ;#else /* ATA cs0/1 on Local Plus cs4/5 */ reg = (reg & ~0x03000000ul ) |0x01000000ul ;
doc/README.phytec.pcm030 new file +46 -0
46 lines not on this page · raw message
include/configs/pcm030.h new file +444 -0
444 lines not on this page · raw message
PATCH v6 1/1 board support patch for phyCORE-MPC5200B-tiny
Quoted 4 lines · Jon Smirl
Add support for the Phytec phyCORE-MPC5200B-tiny. Code originally from Pengutronix.de. Created
CONFIG_SYS_ATA_CS_ON_TIMER01define for when IDE CS is on Timer 0/1Signed-off-by Jon Smirl <[email protected]>
FWIW...
g.
Quoted 960 lines
---
?MAINTAINERS ? ? ? ? ? ? ? ? ? ? ? ? | ? ?4 ?MAKEALL ? ? ? ? ? ? ? ? ? ? ? ? ? ? | ? ?1 ?Makefile ? ? ? ? ? ? ? ? ? ? ? ? ? ?| ? ?9 + ?board/phytec/pcm030/Makefile ? ? ? ?| ? 50 ++++ ?board/phytec/pcm030/config.mk ? ? ? | ? 41 +++ ?board/phytec/pcm030/mt46v32m16-75.h | ? 37 +++ ?board/phytec/pcm030/pcm030.c ? ? ? ?| ?220 +++++++++++++++++ ?cpu/mpc5xxx/ide.c ? ? ? ? ? ? ? ? ? | ? ?3 ?doc/README.phytec.pcm030 ? ? ? ? ? ?| ? 46 ++++ ?include/configs/pcm030.h ? ? ? ? ? ?| ?444 +++++++++++++++++++++++++++++++++++?10 files changed, 855 insertions(+), 0 deletions(-) ?create mode 100644 board/phytec/pcm030/Makefile ?create mode 100644
board/phytec/pcm030/config.mk?create mode 100644board/phytec/pcm030/mt46v32m16-75.h?create mode 100644board/phytec/pcm030/pcm030.c?create mode 100644 doc/README.phytec.pcm030 ?create mode 100644include/configs/pcm030.hMAINTAINERS +0
-0@@ -409,6 +409,10 @@ Andre Schwarz <[email protected]>? ? ? ?mvbc_p ? ? ? ? ?MPC5200
? ? ? ?mvblm7 ? ? ? ? ?MPC8343MAINTAINERS +4
-0+Jon Smirl <[email protected]> + + ? ? ? pcm030 ? ? ? ? ?MPC5200 +?Timur Tabi <[email protected]>
? ? ? ?MPC8349E-mITX ? MPC8349
MAKEALL +1
-0@@ -60,6 +60,7 @@ LIST_5xxx=" ? ? ? ? ? \ ? ? ? ?munices ? ? ? ? \ ? ? ? ?MVBC_P ? ? ? ? ?\ ? ? ? ?o2dnt ? ? ? ? ? \ + ? ? ? pcm030 ? ? ? ? ?\ ? ? ? ?pf5200 ? ? ? ? ?\ ? ? ? ?PM520 ? ? ? ? ? \ ? ? ? ?TB5200 ? ? ? ? ?\Makefile +0
-0@@ -696,6 +696,15 @@ MVBC_P_config: unconfig?o2dnt_config: ?unconfig
? ? ? ?@$(MKCONFIG) o2dnt ppc mpc5xxx o2dntMakefile +9
-0+pcm030_config \ +pcm030_LOWBOOT_config: unconfig + ? ? ? @ >include/config.h + ? ? ? @[ -z "$(findstring LOWBOOT_,$@)" ] || \ + ? ? ? ? ? ? ? { echo "TEXT_BASE = 0xFF000000" >$(obj)board/phytec/pcm030/config.tmp ; \ + ? ? ? ? ? ? ? ? echo "... with LOWBOOT configuration" ; \ + ? ? ? ? ? ? ? } + ? ? ? @$(MKCONFIG) -a pcm030 ppc mpc5xxx pcm030 phytec +?pf5200_config: unconfig
? ? ? ?@$(MKCONFIG) pf5200 ?ppc mpc5xxx pf5200 esdboard/phytec/pcm030/Makefile new file +50
-0@@ -0,0 +1,50 @@ +# +# (C) Copyright 2003-2007 +# Wolfgang Denk, DENX Software Engineering, wd at denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. ?See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB ? ?= $(obj)lib$(BOARD).a + +COBJS ?:= $(BOARD).o + +SRCS ? := $(SOBJS:.o=.S) $(COBJS:.o=.c) +OBJS ? := $(addprefix $(obj),$(COBJS)) +SOBJS ?:= $(addprefix $(obj),$(SOBJS)) + +$(LIB): ? ? ? ?$(obj).depend $(OBJS) + ? ? ? $(AR) $(ARFLAGS) $@ $(OBJS) + +clean: + ? ? ? rm -f $(SOBJS) $(OBJS) + +distclean: ? ? clean + ? ? ? rm -f $(LIB) core *.bak $(obj).depend + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +#########################################################################board/phytec/pcm030/config.mk new file +41
-0@@ -0,0 +1,41 @@ +# +# (C) Copyright 2003 +# Wolfgang Denk, DENX Software Engineering, wd at denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. ?See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +# +# phyCORE-MPC5200B tiny board: +# +# ? ? ?Valid values for TEXT_BASE are: +# +# ? ? ?0xFFF00000 ? boot high (standard configuration) +# ? ? ?0xFF000000 ? boot low +# ? ? ?0x00100000 ? boot from RAM (for testing only) +# + +sinclude $(TOPDIR)/board/$(BOARDDIR)/config.tmp + +ifndef TEXT_BASE +## Standard: boot high +TEXT_BASE = 0xFFF00000 +endif + +PLATFORM_CPPFLAGS += -DTEXT_BASE=$(TEXT_BASE) -I$(TOPDIR)/boardboard/phytec/pcm030/mt46v32m16-75.h new file +37
-0@@ -0,0 +1,37 @@ +/* +* (C) Copyright 2004 +* Mark Jonas, Freescale Semiconductor, mark.jonas at motorola.com. +* +* Eric Schumann, Phytec Messtechnik +* adapted for mt46v32m16-75 DDR-RAM +* +* See file CREDITS for list of people who contributed to this +* project. +* +* This program is free software; you can redistribute it and/or +* modify it under the terms of the GNU General Public License as +* published by the Free Software Foundation; either version 2 of +* the License, or (at your option) any later version. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. ?See the +* GNU General Public License for more details. +* +* You should have received a copy of the GNU General Public License +* along with this program; if not, write to the Free Software +* Foundation, Inc., 59 Temple Place, Suite 330, Boston, +* MA 02111-1307 USA +*/ + +#define SDRAM_DDR ? ? ?1 ? ? ? ? ? ? ?/* is DDR */ + +/* Settings for XLB = 132 MHz */ + +#define SDRAM_MODE ? ? 0x018D0000 +#define SDRAM_EMODE ? ?0x40090000 +#define SDRAM_CONTROL ?0x71500F00 +#define SDRAM_CONFIG1 ?0x73711930 +#define SDRAM_CONFIG2 ?0x47770000 + +#define SDRAM_TAPDELAY 0x10000000/* reserved Bit in MPC5200 B3-Step */ board/phytec/pcm030/pcm030.c new file +220
-0@@ -0,0 +1,220 @@ +/* +* (C) Copyright 2003 +* Wolfgang Denk, DENX Software Engineering, wd at denx.de. +* +* (C) Copyright 2004 +* Mark Jonas, Freescale Semiconductor, mark.jonas at motorola.com. +* +* (C) Copyright 2006 +* Eric Schumann, Phytec Messtechnik GmbH +* +* See file CREDITS for list of people who contributed to this +* project. +* +* This program is free software; you can redistribute it and/or +* modify it under the terms of the GNU General Public License as +* published by the Free Software Foundation; either version 2 of +* the License, or (at your option) any later version. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. ?See the +* GNU General Public License for more details. +* +* You should have received a copy of the GNU General Public License +* along with this program; if not, write to the Free Software +* Foundation, Inc., 59 Temple Place, Suite 330, Boston, +* MA 02111-1307 USA +*/ + +#include <common.h> +#include <mpc5xxx.h> +#include <pci.h> +#include <asm-ppc/io.h> + +#include "mt46v32m16-75.h" + +#ifndef CONFIG_SYS_RAMBOOT +static void sdram_start (int hi_addr) +{ + ? ? ? volatile struct mpc5xxx_cdm *cdm = + ? ? ? ? ? ? ? (struct mpc5xxx_cdm *)MPC5XXX_CDM; + ? ? ? volatile struct mpc5xxx_sdram *sdram = + ? ? ? ? ? ? ? (struct mpc5xxx_sdram *)MPC5XXX_SDRAM; + + ? ? ? long hi_addr_bit = hi_addr ? 0x01000000 : 0; + + ? ? ? /* unlock mode register */ + ? ? ? out_be32 (&sdram->ctrl, + ? ? ? ? ? ? ? (SDRAM_CONTROL | 0x80000000 | hi_addr_bit)); + + ? ? ? /* precharge all banks */ + ? ? ? out_be32 (&sdram->ctrl, + ? ? ? ? ? ? ? (SDRAM_CONTROL | 0x80000002 | hi_addr_bit)); + +#ifdef SDRAM_DDR + ? ? ? /* set mode register: extended mode */ + ? ? ? out_be32 (&sdram->mode, (SDRAM_EMODE)); + + ? ? ? /* set mode register: reset DLL */ + ? ? ? out_be32 (&sdram->mode, + ? ? ? ? ? ? ? (SDRAM_MODE | 0x04000000)); +#endif + + ? ? ? /* precharge all banks */ + ? ? ? out_be32 (&sdram->ctrl, + ? ? ? ? ? ? ? (SDRAM_CONTROL | 0x80000002 | hi_addr_bit)); + + ? ? ? /* auto refresh */ + ? ? ? out_be32 (&sdram->ctrl, + ? ? ? ? ? ? ? (SDRAM_CONTROL | 0x80000004 | hi_addr_bit)); + + ? ? ? /* set mode register */ + ? ? ? out_be32 (&sdram->mode, (SDRAM_MODE)); + + ? ? ? /* normal operation */ + ? ? ? out_be32 (&sdram->ctrl, + ? ? ? ? ? ? ? (SDRAM_CONTROL | hi_addr_bit)); + + ? ? ? /* set CDM clock enable register, set MPC5200B SDRAM bus */ + ? ? ? /* to reduced driver strength */ + ? ? ? out_be32 (&cdm->clock_enable, (0x00CFFFFF)); +} +#endif + +/* +* ATTENTION: Although partially referenced initdram does NOT make +* ? ? real use of CONFIG_SYS_SDRAM_BASE. The code does not +* ? ? work if CONFIG_SYS_SDRAM_BASE +* ? ? is something else than 0x00000000. +*/ + +phys_size_t initdram (int board_type) +{ + ? ? ? volatile struct mpc5xxx_mmap_ctl *mm = + ? ? ? ? ? ? ? (struct mpc5xxx_mmap_ctl *)CONFIG_SYS_MBAR; + ? ? ? volatile struct mpc5xxx_cdm *cdm = + ? ? ? ? ? ? ? (struct mpc5xxx_cdm *)MPC5XXX_CDM; + ? ? ? volatile struct mpc5xxx_sdram *sdram = + ? ? ? ? ? ? ? (struct mpc5xxx_sdram *)MPC5XXX_SDRAM; + ? ? ? ulong dramsize = 0; + ? ? ? ulong dramsize2 = 0; +#ifndef CONFIG_SYS_RAMBOOT + ? ? ? ulong test1, test2; + + ? ? ? /* setup SDRAM chip selects */ + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?/* 256MB at 0x0 */ + ? ? ? out_be32 (&mm->sdram0, 0x0000001b); + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?/* disabled */ + ? ? ? out_be32 (&mm->sdram1, 0x10000000); + + ? ? ? /* setup config registers */ + ? ? ? out_be32 (&sdram->config1, SDRAM_CONFIG1); + ? ? ? out_be32 (&sdram->config2, SDRAM_CONFIG2); + +#if defined(SDRAM_DDR ) && defined(SDRAM_TAPDELAY ) + ? ? ? /* set tap delay */ + ? ? ? out_be32 (&cdm->porcfg, SDRAM_TAPDELAY); +#endif + + ? ? ? /* find RAM size using SDRAM CS0 only */ + ? ? ? sdram_start(0); + ? ? ? test1 = get_ram_size((long *) CONFIG_SYS_SDRAM_BASE, 0x10000000); + ? ? ? sdram_start(1); + ? ? ? test2 = get_ram_size((long *) CONFIG_SYS_SDRAM_BASE, 0x10000000); + ? ? ? if (test1 > test2) { + ? ? ? ? ? ? ? sdram_start(0); + ? ? ? ? ? ? ? dramsize = test1; + ? ? ? } else + ? ? ? ? ? ? ? dramsize = test2; + + ? ? ? /* memory smaller than 1MB is impossible */ + ? ? ? if (dramsize < (1 << 20)) + ? ? ? ? ? ? ? dramsize = 0; + + ? ? ? /* set SDRAM CS0 size according to the amount of RAM found */ + ? ? ? if (dramsize > 0) { + ? ? ? ? ? ? ? out_be32 (&mm->sdram0, + ? ? ? ? ? ? ? ? ? ? ? (0x13 + __builtin_ffs(dramsize >> 20) - 1)); + ? ? ? } else { + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? /* disabled */ + ? ? ? ? ? ? ? out_be32 (&mm->sdram0, 0); + ? ? ? } + +#else /* CONFIG_SYS_RAMBOOT */ + + ? ? ? /* retrieve size of memory connected to SDRAM CS0 */ + ? ? ? dramsize = in_be32(&mm->sdram0) & 0xFF; + ? ? ? if (dramsize >= 0x13) + ? ? ? ? ? ? ? dramsize = (1 << (dramsize - 0x13)) << 20; + ? ? ? else + ? ? ? ? ? ? ? dramsize = 0; + + ? ? ? /* retrieve size of memory connected to SDRAM CS1 */ + ? ? ? dramsize2 = in_be32(&mm->sdram1) & 0xFF; + ? ? ? if (dramsize2 >= 0x13) + ? ? ? ? ? ? ? dramsize2 = (1 << (dramsize2 - 0x13)) << 20; + ? ? ? else + ? ? ? ? ? ? ? dramsize2 = 0; + +#endif /* CONFIG_SYS_RAMBOOT */ + + ? ? ? return dramsize + dramsize2; +} + +int checkboard (void ) +{ + ? ? ? puts("Board: phyCORE-MPC5200B-tiny\n"); + ? ? ? return 0; +} + +#ifdef CONFIG_PCI +static struct pci_controller hose; + +extern void pci_mpc5xxx_init (struct pci_controller *); + +void pci_init_board (void ) +{ + ? ? ? pci_mpc5xxx_init(&hose); +} +#endif + +#if defined(CONFIG_OF_LIBFDT ) && defined(CONFIG_OF_BOARD_SETUP ) +void ft_board_setup (void *blob,bd_t * bd) +{ + ? ? ? ft_cpu_setup(blob, bd); +} +#endif /* defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP) */ + +#if defined(CONFIG_CMD_IDE ) && defined(CONFIG_IDE_RESET ) + +#define GPIO_PSC2_4 ? ?0x02000000UL + +void init_ide_reset (void ) +{ + ? ? ? volatile struct mpc5xxx_wu_gpio *wu_gpio = + ? ? ? ? ? ? ? (struct mpc5xxx_wu_gpio *)MPC5XXX_WU_GPIO; + ? ? ? debug("init_ide_reset\n"); + + ? ? ? /* Configure PSC2_4 as GPIO output for ATA reset */ + ? ? ? setbits_be32(&wu_gpio->enable, GPIO_PSC2_4); + ? ? ? setbits_be32(&wu_gpio->ddr, GPIO_PSC2_4); + ? ? ? /* Deassert reset */ + ? ? ? setbits_be32(&wu_gpio->dvo, GPIO_PSC2_4); +} + +void ide_set_reset (int idereset) +{ + ? ? ? volatile struct mpc5xxx_wu_gpio *wu_gpio = + ? ? ? ? ? ? ? (struct mpc5xxx_wu_gpio *)MPC5XXX_WU_GPIO; + ? ? ? debug("ide_reset(%d)\n", idereset); + + ? ? ? if (idereset) { + ? ? ? ? ? ? ? clrbits_be32(&wu_gpio->dvo, GPIO_PSC2_4); + ? ? ? ? ? ? ? /* Make a delay. MPC5200 spec says 25 usec min */ + ? ? ? ? ? ? ? udelay(500000); + ? ? ? } else + ? ? ? ? ? ? ? setbits_be32(&wu_gpio->dvo, GPIO_PSC2_4); +} +#endif /* defined(CONFIG_CMD_IDE) && defined(CONFIG_IDE_RESET) */ +cpu/mpc5xxx/ide.c +0
-0@@ -45,6 +45,9 @@ int ide_preinit (void) ?#if defined(CONFIG_SYS_ATA_CS_ON_I2C2)? ? ? ?/* ATA cs0/1 on i2c2 clk/io */
? ? ? ?reg = (reg & ~0x03000000ul) |0x02000000ul; +#elifdefined(CONFIG_SYS_ATA_CS_ON_TIMER01)
+ ? ? ? /* ATA cs0/1 on Timer 0/1 */
+ ? ? ? reg = (reg & ~0x03000000ul) |0x03000000ul; ?#else
? ? ? ?/* ATA cs0/1 on Local Plus cs4/5 */ ? ? ? ?reg = (reg & ~0x03000000ul) |0x01000000ul;doc/README.phytec.pcm030 new file +46
-0@@ -0,0 +1,46 @@ +To build RAMBOOT, replace this section the main Makefile + +pcm030_config \ +pcm030_RAMBOOT_config \ +pcm030_LOWBOOT_config: unconfig + ? ? ? @ >include/config.h + ? ? ? @[ -z "$(findstring LOWBOOT_,$@)" ] || \ + ? ? ? ? ? ? ? { echo "TEXT_BASE = 0xFF000000" >board/phytec/pcm030/config.tmp ; \ + ? ? ? ? ? ? ? ? echo "... with LOWBOOT configuration" ; \ + ? ? ? ? ? ? ? } + ? ? ? @[ -z "$(findstring RAMBOOT_,$@)" ] || \ + ? ? ? ? ? ? ?{ echo "TEXT_BASE = 0x00100000" >board/phycore_mpc5200b_tiny/\ + ? ? ? ? ? ? ? ? ? ? ? config.tmp ; \ + ? ? ? ? ? ? ? ?echo "... with RAMBOOT configuration" ; \ + ? ? ? ? ? ? ? ?echo "... remember to make sure that MBAR is already \ + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? switched to 0xF0000000 !!!" ; \ + ? ? ? ? ? ? ?} + ? ? ? @$(MKCONFIG) -a pcm030 ppc mpc5xxx pcm030 phytec + ? ? ? @ echo "remember to set pcm030_REV to 0 for rev 1245.0 rev or to 1 for rev 1245.1" + + +Alternative SDRAM settings: + +#define SDRAM_MODE ? ? 0x018D0000 +#define SDRAM_EMODE ? ?0x40090000 +#define SDRAM_CONTROL ?0x715f0f00 +#define SDRAM_CONFIG1 ?0x73722930 +#define SDRAM_CONFIG2 ?0x47770000 + +/* Settings for XLB = 99 MHz */ +#define SDRAM_MODE ? ? 0x008D0000 +#define SDRAM_EMODE ? ?0x40090000 +#define SDRAM_CONTROL ?0x714b0f00 +#define SDRAM_CONFIG1 ?0x63611730 +#define SDRAM_CONFIG2 ?0x47670000 + +The board ships default with the environment in EEPROM +Moving the environment to flash can be more reliable + +#define CONFIG_ENV_IS_IN_FLASH 1 +#define CONFIG_ENV_ADDR ? ? ? ? ? ? ? ?(CONFIG_SYS_FLASH_BASE + 0xfe0000) +#define CONFIG_ENV_SIZE ? ? ? ? ? ? ? ?0x20000 +#define CONFIG_ENV_SECT_SIZE ? 0x20000 + + +include/configs/pcm030.h new file +444
-0@@ -0,0 +1,444 @@ +/* +* (C) Copyright 2003-2005 +* Wolfgang Denk, DENX Software Engineering, wd at denx.de. +* +* (C) Copyright 2006 +* Eric Schumann, Phytec Messatechnik GmbH +* +* (C) Copyright 2009 +* Jon Smirl <[email protected]> +* +* See file CREDITS for list of people who contributed to this +* project. +* +* This program is free software; you can redistribute it and/or +* modify it under the terms of the GNU General Public License as +* published by the Free Software Foundation; either version 2 of +* the License, or (at your option) any later version. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. ? ? ? ? See the +* GNU General Public License for more details. +* +* You should have received a copy of the GNU General Public License +* along with this program; if not, write to the Free Software +* Foundation, Inc., 59 Temple Place, Suite 330, Boston, +* MA 02111-1307 USA +*/ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#define CONFIG_BOARDINFO ? ? ? ?"phyCORE-MPC5200B-tiny" + +/*----------------------------------------------------------------------------- +High Level Configuration Options +(easy to change) +-----------------------------------------------------------------------------*/ +#define CONFIG_MPC5xxx ? ? ? ? 1 ? ? ?/* This is an MPC5xxx CPU */ +#define CONFIG_MPC5200 ? ? ? ? 1 ? ? ?/* (more precisely an MPC5200 CPU) */ +#define CONFIG_MPC5200_DDR ? ? 1 ? ? ?/* (with DDR-SDRAM) */ +#define CONFIG_PHYCORE_MPC5200B_TINY 1/* phyCORE-MPC5200B -> */ + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? /* FEC configuration and IDE */ +#define CONFIG_SYS_MPC5XXX_CLKIN 33333333/* ... running at 33.333333MHz */ +#define BOOTFLAG_COLD ? ? ? ? ?0x01 ? ?/* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM ? ? ? ? ?0x02 ? ?/* Software reboot */ + +/*----------------------------------------------------------------------------- +Serial console configuration +-----------------------------------------------------------------------------*/ +#define CONFIG_PSC_CONSOLE ? ? 3 ? ? ?/* console is on PSC3 -> */ + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? /*define gps port conf. */ + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? /* register later on to */ + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? /*enable UART function! */ +#define CONFIG_BAUDRATE ? ? ? ? ? ? ? ?115200 ?/* ... at 115200 bps */ +#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } + +/* +* Command line configuration. +*/ +#include <config_cmd_default.h> + +#define CONFIG_CMD_DATE +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_EEPROM +#define CONFIG_CMD_I2C +#define CONFIG_CMD_JFFS2 +#define CONFIG_CMD_MII +#define CONFIG_CMD_NFS +#define CONFIG_CMD_PCI + +#define ? ? ? ?CONFIG_TIMESTAMP ? ? ? ?1 ? ? ? /* Print image info with timestamp */ + +#if (TEXT_BASE == 0xFF000000) ?/* Boot low */ +#define CONFIG_SYS_LOWBOOT 1 +#endif +/* RAMBOOT will be defined automatically in memory section */ + +#define CONFIG_JFFS2_CMDLINE +#define MTDIDS_DEFAULT ? ? ? ? ? ? ? ? "nor0=physmap-flash.0" +#define MTDPARTS_DEFAULT ? ? ? "mtdparts=physmap-flash.0:256k(ubootl)," \ + ? ? ? "1792k(kernel),13312k(jffs2),256k(uboot)ro,256k(oftree),-(space)" + +/*----------------------------------------------------------------------------- +Autobooting +-----------------------------------------------------------------------------*/ +#define CONFIG_BOOTDELAY ? ? ? 3 ? ? ?/* autoboot after 3 seconds */ +#define CONFIG_ZERO_BOOTDELAY_CHECK ? ?/* allow stopping of boot process */ + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? /* even with bootdelay=0 */ +#undef CONFIG_BOOTARGS + + +#define CONFIG_PREBOOT "echo;" \ + ? ? ? "echo Type \"run bootcmd_net\" to load Kernel over TFTP and to "\ + ? ? ? ? ? ? ? "mount root filesystem over NFS;" \ + ? ? ? "echo" + +#define ? ? ? ?CONFIG_EXTRA_ENV_SETTINGS ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? \ + ? ? ? "netdev=eth0\0" ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? \ + ? ? ? "uimage=uImage-pcm030\0" ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?\ + ? ? ? "oftree=oftree-pcm030.dtb\0" ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?\ + ? ? ? "jffs2=root-pcm030.jffs2\0" ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? \ + ? ? ? "uboot=u-boot-pcm030.bin\0" ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? \ + ? ? ? "bargs_base=setenv bootargs console=ttyPSC0,$(baudrate)" ? ? ? ?\ + ? ? ? ? ? ? ? " $(mtdparts) rw\0" ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? \ + ? ? ? "bargs_flash=setenv bootargs $(bootargs) root=/dev/mtdblock2" ? \ + ? ? ? ? ? ? ? " rootfstype=jffs2\0" ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? \ + ? ? ? "bargs_nfs=setenv bootargs $(bootargs) root=/dev/nfs" ? ? ? ? ? \ + ? ? ? ? ? ? ? " ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)::" ? \ + ? ? ? ? ? ? ? "$(netdev):off nfsroot=$(serverip):$(nfsrootfs),v3,tcp\0" \ + ? ? ? "bcmd_net=run bargs_base bargs_nfs; tftpboot 0x500000 $(uimage);" \ + ? ? ? ? ? ? ? " tftp 0x400000 $(oftree); bootm 0x500000 - 0x400000\0" \ + ? ? ? "bcmd_flash=run bargs_base bargs_flash; bootm 0xff040000 - " ? ?\ + ? ? ? ? ? ? ? "0xfff40000\0" ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?\ + ? ? ? ? ? ? ? " cp.b 0x400000 0xff040000 $(filesize)\0" ? ? ? ? ? ? ? \ + ? ? ? "prg_jffs2=tftp 0x400000 $(jffs2); erase 0xff200000 0xffefffff; " \ + ? ? ? ? ? ? ? "cp.b 0x400000 0xff200000 $(filesize)\0" ? ? ? ? ? ? ? ?\ + ? ? ? "prg_oftree=tftp 0x400000 $(oftree); erase 0xfff40000 0xfff5ffff;" \ + ? ? ? ? ? ? ? " cp.b 0x400000 0xfff40000 $(filesize)\0" ? ? ? ? ? ? ? \ + ? ? ? "update=tftpboot 0x400000 $(uboot);erase 0xFFF00000 0xfff3ffff;" \ + ? ? ? ? ? ? ? " cp.b 0x400000 0xFFF00000 $(filesize)\0" ? ? ? ? ? ? ? \ + ? ? ? "unlock=yes\0" ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?\ + ? ? ? "" + +#define CONFIG_BOOTCOMMAND ? ? ? ? ? ? "run bcmd_flash" + +/*-------------------------------------------------------------------------- +IPB Bus clocking configuration. +---------------------------------------------------------------------------*/ +#define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK ? ? ? ?/* define for 133MHz speed */ + +/*------------------------------------------------------------------------- +* PCI Mapping: +* 0x40000000 - 0x4fffffff - PCI Memory +* 0x50000000 - 0x50ffffff - PCI IO Space +* -----------------------------------------------------------------------*/ +#define CONFIG_PCI ? ? ? ? ? ? ? ? ? ? 1 +#define CONFIG_PCI_PNP ? ? ? ? ? ? ? ? 1 +#define CONFIG_PCI_SCAN_SHOW ? ? ? ? ? 1 +#define CONFIG_PCI_MEM_BUS ? ? ? ? ? ? 0x40000000 +#define CONFIG_PCI_MEM_PHYS ? ? ? ? ? ?CONFIG_PCI_MEM_BUS +#define CONFIG_PCI_MEM_SIZE ? ? ? ? ? ?0x10000000 +#define CONFIG_PCI_IO_BUS ? ? ? ? ? ? ?0x50000000 +#define CONFIG_PCI_IO_PHYS ? ? ? ? ? ? CONFIG_PCI_IO_BUS +#define CONFIG_PCI_IO_SIZE ? ? ? ? ? ? 0x01000000 +#define CONFIG_SYS_XLB_PIPELINING ? ? ?1 + +/*--------------------------------------------------------------------------- +I2C configuration +---------------------------------------------------------------------------*/ +#define CONFIG_HARD_I2C 1/* I2C with hardware support */ +#define CONFIG_SYS_I2C_MODULE 2/* Select I2C module #1 or #2 */ +#define CONFIG_SYS_I2C_SPEED 100000/* 100 kHz */ +#define CONFIG_SYS_I2C_SLAVE 0x7F + +/*--------------------------------------------------------------------------- +EEPROM CAT24WC32 configuration +---------------------------------------------------------------------------*/ +#define CONFIG_SYS_I2C_EEPROM_ADDR ? ? 0x52 ? ?/* 1010100x */ +#define CONFIG_SYS_I2C_FACT_ADDR ? ? ? 0x52 ? ?/* EEPROM CAT24WC32 */ +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 ? ? ?/* Bytes of address */ +#define CONFIG_SYS_EEPROM_SIZE ? ? ? ? 2048 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 15 + +/*--------------------------------------------------------------------------- +RTC configuration +---------------------------------------------------------------------------*/ +#define RTC +#define CONFIG_RTC_PCF8563 ? ? ? ? ? ? 1 +#define CONFIG_SYS_I2C_RTC_ADDR ? ? ? ? ? ? ? ?0x51 + +/*--------------------------------------------------------------------------- +Flash configuration +---------------------------------------------------------------------------*/ + +#define CONFIG_SYS_FLASH_BASE ? ? ? ? ?0xff000000 +#define CONFIG_SYS_FLASH_SIZE ? ? ? ? ?0x01000000 +#define CONFIG_SYS_FLASH_BANKS_LIST ? ?{ CONFIG_SYS_FLASH_BASE } + +#define CONFIG_SYS_FLASH_CFI ? ? ? ? ? 1 ? ? ?/* Flash is CFI conformant */ +#define CONFIG_FLASH_CFI_DRIVER ? ? ? ?1 ? ? ?/* Use the common driver */ +#define CONFIG_SYS_FLASH_EMPTY_INFO +#define CONFIG_SYS_MAX_FLASH_SECT 260/* max num of sects on one chip */ +#define CONFIG_SYS_MAX_FLASH_BANKS 1/* max num of flash banks */ + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? /* (= chip selects) */ +#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE + +/* +* Use also hardware protection. This seems required, as the BDI uses +* hardware protection. Without this, U-Boot can't work with this sectors, +* as its protection is software only by default +*/ +#define CONFIG_SYS_FLASH_PROTECTION ? ?1 + +/*--------------------------------------------------------------------------- +Environment settings +---------------------------------------------------------------------------*/ + +/* pcm030 ships with environment is EEPROM by default */ +#define CONFIG_ENV_IS_IN_EEPROM ? ? ? ?1 +#define CONFIG_ENV_OFFSET ? ? ?0x00 ? ?/* environment starts at the */ + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? /*beginning of the EEPROM */ +#define CONFIG_ENV_SIZE ? ? ? ? ? ? ? ?CONFIG_SYS_EEPROM_SIZE + +#define CONFIG_ENV_OVERWRITE ? 1 + +/*----------------------------------------------------------------------------- +?Memory map +-----------------------------------------------------------------------------*/ +#define CONFIG_SYS_MBAR ? ? ? ?0xF0000000 ? ? ?/* MBAR has to be switched by other */ + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? /* bootloader or debugger config */ +#define CONFIG_SYS_SDRAM_BASE ? ? ? ? ?0x00000000 +#define CONFIG_SYS_DEFAULT_MBAR ? ? ? ? ? ? ? ?0x80000000 +/* Use SRAM until RAM will be available */ +#define CONFIG_SYS_INIT_RAM_ADDR ? ? ? MPC5XXX_SRAM +#define CONFIG_SYS_INIT_RAM_END ? ? ? ? ? ? ? ?MPC5XXX_SRAM_SIZE ? ? ?/* End of used */ + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? /* area in DPRAM */ +#define CONFIG_SYS_GBL_DATA_SIZE ? ? ? 128 ? ?/* size in bytes */ + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? /* reserved for initial data */ +#define CONFIG_SYS_GBL_DATA_OFFSET ? ? (CONFIG_SYS_INIT_RAM_END - \ + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET ? ? ?CONFIG_SYS_GBL_DATA_OFFSET + +#define CONFIG_SYS_MONITOR_BASE ? ? ? ?TEXT_BASE +#if (CONFIG_SYS_MONITOR_BASE <CONFIG_SYS_FLASH_BASE ) +# ? ? ?define CONFIG_SYS_RAMBOOT ? ? ? ? ? ? ? 1 +#endif + +#define CONFIG_SYS_MONITOR_LEN (192 << 10)/* Reserve 192 kB for Monitor */ +#define CONFIG_SYS_MALLOC_LEN (128 << 10)/* Reserve 128 kB for malloc() */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20)/* Initial Memory map for Linux */ + +/*----------------------------------------------------------------------------- +Ethernet configuration +-----------------------------------------------------------------------------*/ +#define CONFIG_MPC5xxx_FEC ? ? ? ? ? ? 1 +#define CONFIG_MPC5xxx_FEC_MII100 +#define CONFIG_PHY_ADDR ? ? ? ? ? ? ? ? ? ? ? ?0x01 + +/*--------------------------------------------------------------------------- +GPIO configuration +---------------------------------------------------------------------------*/ + +/* GPIO port configuration +* +* Pin mapping: +* +* [29:31] = 01x +* PSC1_0 -> AC97 SDATA out +* PSC1_1 -> AC97 SDTA in +* PSC1_2 -> AC97 SYNC out +* PSC1_3 -> AC97 bitclock out +* PSC1_4 -> AC97 reset out +* +* [25:27] = 001 +* PSC2_0 -> CAN 1 Tx out +* PSC2_1 -> CAN 1 Rx in +* PSC2_2 -> CAN 2 Tx out +* PSC2_3 -> CAN 2 Rx in +* PSC2_4 -> GPIO (claimed for ATA reset, active low) +* +* +* [20:23] = 1100 +* PSC3_0 -> UART Tx out +* PSC3_1 -> UART Rx in +* PSC3_2 -> UART RTS (in/out FIXME) +* PSC3_3 -> UART CTS (in/out FIXME) +* PSC3_4 -> LocalPlus Bus CS6 \ +* PSC3_5 -> LocalPlus Bus CS7 / --> see [4] and [5] +* PSC3_6 -> dedicated SPI MOSI out (master case) +* PSC3_7 -> dedicated SPI MISO in (master case) +* PSC3_8 -> dedicated SPI SS out (master case) +* PSC3_9 -> dedicated SPI CLK out (master case) +* +* [18:19] = 01 +* USB_0 -> USB OE out +* USB_1 -> USB Tx- out +* USB_2 -> USB Tx+ out +* USB_3 -> USB RxD (in/out FIXME) +* USB_4 -> USB Rx+ in +* USB_5 -> USB Rx- in +* USB_6 -> USB PortPower out +* USB_7 -> USB speed out +* USB_8 -> USB suspend (in/out FIXME) +* USB_9 -> USB overcurrent in +* +* [17] = 0 +* USB differential mode +* +* [16] = 0 +* PCI enabled +* +* [12:15] = 0101 +* ETH_0 -> ETH Txen +* ETH_1 -> ETH TxD0 +* ETH_2 -> ETH TxD1 +* ETH_3 -> ETH TxD2 +* ETH_4 -> ETH TxD3 +* ETH_5 -> ETH Txerr +* ETH_6 -> ETH MDC +* ETH_7 -> ETH MDIO +* ETH_8 -> ETH RxDv +* ETH_9 -> ETH RxCLK +* ETH_10 -> ETH Collision +* ETH_11 -> ETH TxD +* ETH_12 -> ETH RxD0 +* ETH_13 -> ETH RxD1 +* ETH_14 -> ETH RxD2 +* ETH_15 -> ETH RxD3 +* ETH_16 -> ETH Rxerr +* ETH_17 -> ETH CRS +* +* [9:11] = 101 +* PSC6_0 -> UART RxD in +* PSC6_1 -> UART CTS (in/out FIXME) +* PSC6_2 -> UART TxD out +* PSC6_3 -> UART RTS (in/out FIXME) +* +* [2:3/6:7] = 00/11 +* TMR_0 -> ATA_CS0 out +* TMR_1 -> ATA_CS1 out +* TMR_2 -> GPIO +* TMR_3 -> GPIO +* TMR_4 -> GPIO +* TMR_5 -> GPIO +* TMR_6 -> GPIO +* TMR_7 -> GPIO +* I2C_0 -> I2C 1 Clock out +* I2C_1 -> I2C 1 IO in/out +* I2C_2 -> I2C 2 Clock out +* I2C_3 -> I2C 2 IO in/out +* +* [4] = 1 +* PSC3_5 is used as CS7 +* +* [5] = 1 +* PSC3_4 is used as CS6 +* +* [1] = 0 +* gpio_wkup_7 is GPIO +* +* [0] = 0 +* gpio_wkup_6 is GPIO +* +*/ +#define CONFIG_SYS_GPS_PORT_CONFIG ? ? 0x0f551c12 + +/*----------------------------------------------------------------------------- +Miscellaneous configurable options +-------------------------------------------------------------------------------*/ +#define CONFIG_SYS_LONGHELP ? ?/* undef to save memory */ +#define CONFIG_SYS_PROMPT "uboot> "/* Monitor Command Prompt */ + +#define CONFIG_CMDLINE_EDITING 1/* add command line history */ + +#define CONFIG_SYS_CACHELINE_SIZE 32/* For MPC5xxx CPUs */ +#if defined(CONFIG_CMD_KGDB ) +#define CONFIG_SYS_CACHELINE_SHIFT 5/* log base 2 of the above value */ +#endif + +#if defined(CONFIG_CMD_KGDB ) +#define CONFIG_SYS_CBSIZE 1024/* Console I/O Buffer Size */ +#else +#define CONFIG_SYS_CBSIZE 256/* Console I/O Buffer Size */ +#endif +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16/* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */ + +#define CONFIG_SYS_MEMTEST_START 0x00100000/* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x00f00000/* 1 ... 15 MB in DRAM */ + +#define CONFIG_SYS_LOAD_ADDR 0x400000/* default load address */ +#define CONFIG_SYS_HZ 1000/* decrementer freq: 1 ms ticks */ + +#define CONFIG_DISPLAY_BOARDINFO 1 + +/*----------------------------------------------------------------------------- +Various low-level settings +-----------------------------------------------------------------------------*/ +#define CONFIG_SYS_HID0_INIT ? ? ? ? ? HID0_ICE | HID0_ICFI +#define CONFIG_SYS_HID0_FINAL ? ? ? ? ?HID0_ICE + +/* no burst access on the LPB */ +#define CONFIG_SYS_CS_BURST ? ? ? ? ? ?0x00000000 +/* one deadcycle for the 33MHz statemachine */ +#define CONFIG_SYS_CS_DEADCYCLE ? ? ? ? ? ? ? ?0x33333331 +/* one additional waitstate for the 33MHz statemachine */ +#define CONFIG_SYS_BOOTCS_CFG ? ? ? ? ?0x0001dd00 +#define CONFIG_SYS_BOOTCS_START ? ? ? ? ? ? ? ?CONFIG_SYS_FLASH_BASE +#define CONFIG_SYS_BOOTCS_SIZE ? ? ? ? CONFIG_SYS_FLASH_SIZE + +#define CONFIG_SYS_RESET_ADDRESS ? ? ? 0xff000000 + +/*----------------------------------------------------------------------- +* USB stuff +*----------------------------------------------------------------------- +*/ +#define CONFIG_USB_CLOCK ? ? ? ? ? ? ? 0x0001BBBB +#define CONFIG_USB_CONFIG ? ? ? ? ? ? ?0x00001000 + +/*--------------------------------------------------------------------------- +IDE/ATA stuff Supports IDE harddisk +----------------------------------------------------------------------------*/ + +#undef ?CONFIG_IDE_8xx_PCCARD ?/* Use IDE with PC Card Adapter */ +#undef CONFIG_IDE_8xx_DIRECT ?/* Direct IDE not supported */ +#undef CONFIG_IDE_LED ? ? ? ? ?/* LED for ide not supported */ +#define CONFIG_SYS_ATA_CS_ON_TIMER01 +#define ? ? ? ?CONFIG_IDE_RESET 1 ? ? ?/* reset for ide supported */ +#define CONFIG_IDE_PREINIT +#define CONFIG_SYS_IDE_MAXBUS 1/* max. 1 IDE bus */ +#define CONFIG_SYS_IDE_MAXDEVICE 2/* max. 2 drives per IDE bus */ +#define CONFIG_SYS_ATA_IDE0_OFFSET ? ? 0x0000 +#define CONFIG_SYS_ATA_BASE_ADDR ? ? ? MPC5XXX_ATA +/* Offset for data I/O ? ? ? ? ? ? ? ? */ +#define CONFIG_SYS_ATA_DATA_OFFSET ? ? (0x0060) +/* Offset for normal register accesses */ +#define CONFIG_SYS_ATA_REG_OFFSET ? ? ?(CONFIG_SYS_ATA_DATA_OFFSET) +/* Offset for alternate registers ? ? ?*/ +#define CONFIG_SYS_ATA_ALT_OFFSET ? ? ?(0x005C) +/* Interval between registers */ +#define CONFIG_SYS_ATA_STRIDE ? ? ? ? ?4 +#define CONFIG_ATAPI ? ? ? ? ? ? ? ? ? 1 + +/* we enable IDE and FAT support, so we also need partition support */ +#define CONFIG_DOS_PARTITION 1 + +/* USB */ +#define CONFIG_USB_OHCI +#define CONFIG_USB_STORAGE + +/* pass open firmware flat tree */ +#define CONFIG_OF_LIBFDT ? ? ? ? ? ? ? 1 +#define CONFIG_OF_BOARD_SETUP ? ? ? ? ?1 + +#define OF_CPU ? ? ? ? ? ? ? ? ? ? ? ? "PowerPC,5200 at 0" +#define OF_TBCLK ? ? ? ? ? ? ? ? ? ? ? CONFIG_SYS_MPC5XXX_CLKIN +#define OF_SOC ? ? ? ? ? ? ? ? ? ? ? ? "soc5200 at f0000000" +#define OF_STDOUT_PATH ? ? ? ? ? ? ? ? "/soc5200 at f0000000/serial at 2400" + +#endif /* __CONFIG_H */ _______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
Signature · 2 lines
Grant Likely, B.Sc., P.Eng. Secret Lab Technologies Ltd.
PATCH v6 1/1 board support patch for phyCORE-MPC5200B-tiny
In reply to Jon SmirlWhat is the merge status of this patch? Can we please get it applied to the 5xxx tree?
Quoted 960 lines · Jon Smirl
Add support for the Phytec phyCORE-MPC5200B-tiny. Code originally from Pengutronix.de. Created
CONFIG_SYS_ATA_CS_ON_TIMER01define for when IDE CS is on Timer 0/1Signed-off-by Jon Smirl <[email protected]>---
?MAINTAINERS ? ? ? ? ? ? ? ? ? ? ? ? | ? ?4 ?MAKEALL ? ? ? ? ? ? ? ? ? ? ? ? ? ? | ? ?1 ?Makefile ? ? ? ? ? ? ? ? ? ? ? ? ? ?| ? ?9 + ?board/phytec/pcm030/Makefile ? ? ? ?| ? 50 ++++ ?board/phytec/pcm030/config.mk ? ? ? | ? 41 +++ ?board/phytec/pcm030/mt46v32m16-75.h | ? 37 +++ ?board/phytec/pcm030/pcm030.c ? ? ? ?| ?220 +++++++++++++++++ ?cpu/mpc5xxx/ide.c ? ? ? ? ? ? ? ? ? | ? ?3 ?doc/README.phytec.pcm030 ? ? ? ? ? ?| ? 46 ++++ ?include/configs/pcm030.h ? ? ? ? ? ?| ?444 +++++++++++++++++++++++++++++++++++?10 files changed, 855 insertions(+), 0 deletions(-) ?create mode 100644 board/phytec/pcm030/Makefile ?create mode 100644
board/phytec/pcm030/config.mk?create mode 100644board/phytec/pcm030/mt46v32m16-75.h?create mode 100644board/phytec/pcm030/pcm030.c?create mode 100644 doc/README.phytec.pcm030 ?create mode 100644include/configs/pcm030.hMAINTAINERS +0
-0@@ -409,6 +409,10 @@ Andre Schwarz <[email protected]>? ? ? ?mvbc_p ? ? ? ? ?MPC5200
? ? ? ?mvblm7 ? ? ? ? ?MPC8343MAINTAINERS +4
-0+Jon Smirl <[email protected]> + + ? ? ? pcm030 ? ? ? ? ?MPC5200 +?Timur Tabi <[email protected]>
? ? ? ?MPC8349E-mITX ? MPC8349
MAKEALL +1
-0@@ -60,6 +60,7 @@ LIST_5xxx=" ? ? ? ? ? \ ? ? ? ?munices ? ? ? ? \ ? ? ? ?MVBC_P ? ? ? ? ?\ ? ? ? ?o2dnt ? ? ? ? ? \ + ? ? ? pcm030 ? ? ? ? ?\ ? ? ? ?pf5200 ? ? ? ? ?\ ? ? ? ?PM520 ? ? ? ? ? \ ? ? ? ?TB5200 ? ? ? ? ?\Makefile +0
-0@@ -696,6 +696,15 @@ MVBC_P_config: unconfig?o2dnt_config: ?unconfig
? ? ? ?@$(MKCONFIG) o2dnt ppc mpc5xxx o2dntMakefile +9
-0+pcm030_config \ +pcm030_LOWBOOT_config: unconfig + ? ? ? @ >include/config.h + ? ? ? @[ -z "$(findstring LOWBOOT_,$@)" ] || \ + ? ? ? ? ? ? ? { echo "TEXT_BASE = 0xFF000000" >$(obj)board/phytec/pcm030/config.tmp ; \ + ? ? ? ? ? ? ? ? echo "... with LOWBOOT configuration" ; \ + ? ? ? ? ? ? ? } + ? ? ? @$(MKCONFIG) -a pcm030 ppc mpc5xxx pcm030 phytec +?pf5200_config: unconfig
? ? ? ?@$(MKCONFIG) pf5200 ?ppc mpc5xxx pf5200 esdboard/phytec/pcm030/Makefile new file +50
-0@@ -0,0 +1,50 @@ +# +# (C) Copyright 2003-2007 +# Wolfgang Denk, DENX Software Engineering, wd at denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. ?See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB ? ?= $(obj)lib$(BOARD).a + +COBJS ?:= $(BOARD).o + +SRCS ? := $(SOBJS:.o=.S) $(COBJS:.o=.c) +OBJS ? := $(addprefix $(obj),$(COBJS)) +SOBJS ?:= $(addprefix $(obj),$(SOBJS)) + +$(LIB): ? ? ? ?$(obj).depend $(OBJS) + ? ? ? $(AR) $(ARFLAGS) $@ $(OBJS) + +clean: + ? ? ? rm -f $(SOBJS) $(OBJS) + +distclean: ? ? clean + ? ? ? rm -f $(LIB) core *.bak $(obj).depend + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +#########################################################################board/phytec/pcm030/config.mk new file +41
-0@@ -0,0 +1,41 @@ +# +# (C) Copyright 2003 +# Wolfgang Denk, DENX Software Engineering, wd at denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. ?See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +# +# phyCORE-MPC5200B tiny board: +# +# ? ? ?Valid values for TEXT_BASE are: +# +# ? ? ?0xFFF00000 ? boot high (standard configuration) +# ? ? ?0xFF000000 ? boot low +# ? ? ?0x00100000 ? boot from RAM (for testing only) +# + +sinclude $(TOPDIR)/board/$(BOARDDIR)/config.tmp + +ifndef TEXT_BASE +## Standard: boot high +TEXT_BASE = 0xFFF00000 +endif + +PLATFORM_CPPFLAGS += -DTEXT_BASE=$(TEXT_BASE) -I$(TOPDIR)/boardboard/phytec/pcm030/mt46v32m16-75.h new file +37
-0@@ -0,0 +1,37 @@ +/* +* (C) Copyright 2004 +* Mark Jonas, Freescale Semiconductor, mark.jonas at motorola.com. +* +* Eric Schumann, Phytec Messtechnik +* adapted for mt46v32m16-75 DDR-RAM +* +* See file CREDITS for list of people who contributed to this +* project. +* +* This program is free software; you can redistribute it and/or +* modify it under the terms of the GNU General Public License as +* published by the Free Software Foundation; either version 2 of +* the License, or (at your option) any later version. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. ?See the +* GNU General Public License for more details. +* +* You should have received a copy of the GNU General Public License +* along with this program; if not, write to the Free Software +* Foundation, Inc., 59 Temple Place, Suite 330, Boston, +* MA 02111-1307 USA +*/ + +#define SDRAM_DDR ? ? ?1 ? ? ? ? ? ? ?/* is DDR */ + +/* Settings for XLB = 132 MHz */ + +#define SDRAM_MODE ? ? 0x018D0000 +#define SDRAM_EMODE ? ?0x40090000 +#define SDRAM_CONTROL ?0x71500F00 +#define SDRAM_CONFIG1 ?0x73711930 +#define SDRAM_CONFIG2 ?0x47770000 + +#define SDRAM_TAPDELAY 0x10000000/* reserved Bit in MPC5200 B3-Step */ board/phytec/pcm030/pcm030.c new file +220
-0@@ -0,0 +1,220 @@ +/* +* (C) Copyright 2003 +* Wolfgang Denk, DENX Software Engineering, wd at denx.de. +* +* (C) Copyright 2004 +* Mark Jonas, Freescale Semiconductor, mark.jonas at motorola.com. +* +* (C) Copyright 2006 +* Eric Schumann, Phytec Messtechnik GmbH +* +* See file CREDITS for list of people who contributed to this +* project. +* +* This program is free software; you can redistribute it and/or +* modify it under the terms of the GNU General Public License as +* published by the Free Software Foundation; either version 2 of +* the License, or (at your option) any later version. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. ?See the +* GNU General Public License for more details. +* +* You should have received a copy of the GNU General Public License +* along with this program; if not, write to the Free Software +* Foundation, Inc., 59 Temple Place, Suite 330, Boston, +* MA 02111-1307 USA +*/ + +#include <common.h> +#include <mpc5xxx.h> +#include <pci.h> +#include <asm-ppc/io.h> + +#include "mt46v32m16-75.h" + +#ifndef CONFIG_SYS_RAMBOOT +static void sdram_start (int hi_addr) +{ + ? ? ? volatile struct mpc5xxx_cdm *cdm = + ? ? ? ? ? ? ? (struct mpc5xxx_cdm *)MPC5XXX_CDM; + ? ? ? volatile struct mpc5xxx_sdram *sdram = + ? ? ? ? ? ? ? (struct mpc5xxx_sdram *)MPC5XXX_SDRAM; + + ? ? ? long hi_addr_bit = hi_addr ? 0x01000000 : 0; + + ? ? ? /* unlock mode register */ + ? ? ? out_be32 (&sdram->ctrl, + ? ? ? ? ? ? ? (SDRAM_CONTROL | 0x80000000 | hi_addr_bit)); + + ? ? ? /* precharge all banks */ + ? ? ? out_be32 (&sdram->ctrl, + ? ? ? ? ? ? ? (SDRAM_CONTROL | 0x80000002 | hi_addr_bit)); + +#ifdef SDRAM_DDR + ? ? ? /* set mode register: extended mode */ + ? ? ? out_be32 (&sdram->mode, (SDRAM_EMODE)); + + ? ? ? /* set mode register: reset DLL */ + ? ? ? out_be32 (&sdram->mode, + ? ? ? ? ? ? ? (SDRAM_MODE | 0x04000000)); +#endif + + ? ? ? /* precharge all banks */ + ? ? ? out_be32 (&sdram->ctrl, + ? ? ? ? ? ? ? (SDRAM_CONTROL | 0x80000002 | hi_addr_bit)); + + ? ? ? /* auto refresh */ + ? ? ? out_be32 (&sdram->ctrl, + ? ? ? ? ? ? ? (SDRAM_CONTROL | 0x80000004 | hi_addr_bit)); + + ? ? ? /* set mode register */ + ? ? ? out_be32 (&sdram->mode, (SDRAM_MODE)); + + ? ? ? /* normal operation */ + ? ? ? out_be32 (&sdram->ctrl, + ? ? ? ? ? ? ? (SDRAM_CONTROL | hi_addr_bit)); + + ? ? ? /* set CDM clock enable register, set MPC5200B SDRAM bus */ + ? ? ? /* to reduced driver strength */ + ? ? ? out_be32 (&cdm->clock_enable, (0x00CFFFFF)); +} +#endif + +/* +* ATTENTION: Although partially referenced initdram does NOT make +* ? ? real use of CONFIG_SYS_SDRAM_BASE. The code does not +* ? ? work if CONFIG_SYS_SDRAM_BASE +* ? ? is something else than 0x00000000. +*/ + +phys_size_t initdram (int board_type) +{ + ? ? ? volatile struct mpc5xxx_mmap_ctl *mm = + ? ? ? ? ? ? ? (struct mpc5xxx_mmap_ctl *)CONFIG_SYS_MBAR; + ? ? ? volatile struct mpc5xxx_cdm *cdm = + ? ? ? ? ? ? ? (struct mpc5xxx_cdm *)MPC5XXX_CDM; + ? ? ? volatile struct mpc5xxx_sdram *sdram = + ? ? ? ? ? ? ? (struct mpc5xxx_sdram *)MPC5XXX_SDRAM; + ? ? ? ulong dramsize = 0; + ? ? ? ulong dramsize2 = 0; +#ifndef CONFIG_SYS_RAMBOOT + ? ? ? ulong test1, test2; + + ? ? ? /* setup SDRAM chip selects */ + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?/* 256MB at 0x0 */ + ? ? ? out_be32 (&mm->sdram0, 0x0000001b); + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?/* disabled */ + ? ? ? out_be32 (&mm->sdram1, 0x10000000); + + ? ? ? /* setup config registers */ + ? ? ? out_be32 (&sdram->config1, SDRAM_CONFIG1); + ? ? ? out_be32 (&sdram->config2, SDRAM_CONFIG2); + +#if defined(SDRAM_DDR ) && defined(SDRAM_TAPDELAY ) + ? ? ? /* set tap delay */ + ? ? ? out_be32 (&cdm->porcfg, SDRAM_TAPDELAY); +#endif + + ? ? ? /* find RAM size using SDRAM CS0 only */ + ? ? ? sdram_start(0); + ? ? ? test1 = get_ram_size((long *) CONFIG_SYS_SDRAM_BASE, 0x10000000); + ? ? ? sdram_start(1); + ? ? ? test2 = get_ram_size((long *) CONFIG_SYS_SDRAM_BASE, 0x10000000); + ? ? ? if (test1 > test2) { + ? ? ? ? ? ? ? sdram_start(0); + ? ? ? ? ? ? ? dramsize = test1; + ? ? ? } else + ? ? ? ? ? ? ? dramsize = test2; + + ? ? ? /* memory smaller than 1MB is impossible */ + ? ? ? if (dramsize < (1 << 20)) + ? ? ? ? ? ? ? dramsize = 0; + + ? ? ? /* set SDRAM CS0 size according to the amount of RAM found */ + ? ? ? if (dramsize > 0) { + ? ? ? ? ? ? ? out_be32 (&mm->sdram0, + ? ? ? ? ? ? ? ? ? ? ? (0x13 + __builtin_ffs(dramsize >> 20) - 1)); + ? ? ? } else { + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? /* disabled */ + ? ? ? ? ? ? ? out_be32 (&mm->sdram0, 0); + ? ? ? } + +#else /* CONFIG_SYS_RAMBOOT */ + + ? ? ? /* retrieve size of memory connected to SDRAM CS0 */ + ? ? ? dramsize = in_be32(&mm->sdram0) & 0xFF; + ? ? ? if (dramsize >= 0x13) + ? ? ? ? ? ? ? dramsize = (1 << (dramsize - 0x13)) << 20; + ? ? ? else + ? ? ? ? ? ? ? dramsize = 0; + + ? ? ? /* retrieve size of memory connected to SDRAM CS1 */ + ? ? ? dramsize2 = in_be32(&mm->sdram1) & 0xFF; + ? ? ? if (dramsize2 >= 0x13) + ? ? ? ? ? ? ? dramsize2 = (1 << (dramsize2 - 0x13)) << 20; + ? ? ? else + ? ? ? ? ? ? ? dramsize2 = 0; + +#endif /* CONFIG_SYS_RAMBOOT */ + + ? ? ? return dramsize + dramsize2; +} + +int checkboard (void ) +{ + ? ? ? puts("Board: phyCORE-MPC5200B-tiny\n"); + ? ? ? return 0; +} + +#ifdef CONFIG_PCI +static struct pci_controller hose; + +extern void pci_mpc5xxx_init (struct pci_controller *); + +void pci_init_board (void ) +{ + ? ? ? pci_mpc5xxx_init(&hose); +} +#endif + +#if defined(CONFIG_OF_LIBFDT ) && defined(CONFIG_OF_BOARD_SETUP ) +void ft_board_setup (void *blob,bd_t * bd) +{ + ? ? ? ft_cpu_setup(blob, bd); +} +#endif /* defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP) */ + +#if defined(CONFIG_CMD_IDE ) && defined(CONFIG_IDE_RESET ) + +#define GPIO_PSC2_4 ? ?0x02000000UL + +void init_ide_reset (void ) +{ + ? ? ? volatile struct mpc5xxx_wu_gpio *wu_gpio = + ? ? ? ? ? ? ? (struct mpc5xxx_wu_gpio *)MPC5XXX_WU_GPIO; + ? ? ? debug("init_ide_reset\n"); + + ? ? ? /* Configure PSC2_4 as GPIO output for ATA reset */ + ? ? ? setbits_be32(&wu_gpio->enable, GPIO_PSC2_4); + ? ? ? setbits_be32(&wu_gpio->ddr, GPIO_PSC2_4); + ? ? ? /* Deassert reset */ + ? ? ? setbits_be32(&wu_gpio->dvo, GPIO_PSC2_4); +} + +void ide_set_reset (int idereset) +{ + ? ? ? volatile struct mpc5xxx_wu_gpio *wu_gpio = + ? ? ? ? ? ? ? (struct mpc5xxx_wu_gpio *)MPC5XXX_WU_GPIO; + ? ? ? debug("ide_reset(%d)\n", idereset); + + ? ? ? if (idereset) { + ? ? ? ? ? ? ? clrbits_be32(&wu_gpio->dvo, GPIO_PSC2_4); + ? ? ? ? ? ? ? /* Make a delay. MPC5200 spec says 25 usec min */ + ? ? ? ? ? ? ? udelay(500000); + ? ? ? } else + ? ? ? ? ? ? ? setbits_be32(&wu_gpio->dvo, GPIO_PSC2_4); +} +#endif /* defined(CONFIG_CMD_IDE) && defined(CONFIG_IDE_RESET) */ +cpu/mpc5xxx/ide.c +0
-0@@ -45,6 +45,9 @@ int ide_preinit (void) ?#if defined(CONFIG_SYS_ATA_CS_ON_I2C2)? ? ? ?/* ATA cs0/1 on i2c2 clk/io */
? ? ? ?reg = (reg & ~0x03000000ul) |0x02000000ul; +#elifdefined(CONFIG_SYS_ATA_CS_ON_TIMER01)
+ ? ? ? /* ATA cs0/1 on Timer 0/1 */
+ ? ? ? reg = (reg & ~0x03000000ul) |0x03000000ul; ?#else
? ? ? ?/* ATA cs0/1 on Local Plus cs4/5 */ ? ? ? ?reg = (reg & ~0x03000000ul) |0x01000000ul;doc/README.phytec.pcm030 new file +46
-0@@ -0,0 +1,46 @@ +To build RAMBOOT, replace this section the main Makefile + +pcm030_config \ +pcm030_RAMBOOT_config \ +pcm030_LOWBOOT_config: unconfig + ? ? ? @ >include/config.h + ? ? ? @[ -z "$(findstring LOWBOOT_,$@)" ] || \ + ? ? ? ? ? ? ? { echo "TEXT_BASE = 0xFF000000" >board/phytec/pcm030/config.tmp ; \ + ? ? ? ? ? ? ? ? echo "... with LOWBOOT configuration" ; \ + ? ? ? ? ? ? ? } + ? ? ? @[ -z "$(findstring RAMBOOT_,$@)" ] || \ + ? ? ? ? ? ? ?{ echo "TEXT_BASE = 0x00100000" >board/phycore_mpc5200b_tiny/\ + ? ? ? ? ? ? ? ? ? ? ? config.tmp ; \ + ? ? ? ? ? ? ? ?echo "... with RAMBOOT configuration" ; \ + ? ? ? ? ? ? ? ?echo "... remember to make sure that MBAR is already \ + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? switched to 0xF0000000 !!!" ; \ + ? ? ? ? ? ? ?} + ? ? ? @$(MKCONFIG) -a pcm030 ppc mpc5xxx pcm030 phytec + ? ? ? @ echo "remember to set pcm030_REV to 0 for rev 1245.0 rev or to 1 for rev 1245.1" + + +Alternative SDRAM settings: + +#define SDRAM_MODE ? ? 0x018D0000 +#define SDRAM_EMODE ? ?0x40090000 +#define SDRAM_CONTROL ?0x715f0f00 +#define SDRAM_CONFIG1 ?0x73722930 +#define SDRAM_CONFIG2 ?0x47770000 + +/* Settings for XLB = 99 MHz */ +#define SDRAM_MODE ? ? 0x008D0000 +#define SDRAM_EMODE ? ?0x40090000 +#define SDRAM_CONTROL ?0x714b0f00 +#define SDRAM_CONFIG1 ?0x63611730 +#define SDRAM_CONFIG2 ?0x47670000 + +The board ships default with the environment in EEPROM +Moving the environment to flash can be more reliable + +#define CONFIG_ENV_IS_IN_FLASH 1 +#define CONFIG_ENV_ADDR ? ? ? ? ? ? ? ?(CONFIG_SYS_FLASH_BASE + 0xfe0000) +#define CONFIG_ENV_SIZE ? ? ? ? ? ? ? ?0x20000 +#define CONFIG_ENV_SECT_SIZE ? 0x20000 + + +include/configs/pcm030.h new file +444
-0@@ -0,0 +1,444 @@ +/* +* (C) Copyright 2003-2005 +* Wolfgang Denk, DENX Software Engineering, wd at denx.de. +* +* (C) Copyright 2006 +* Eric Schumann, Phytec Messatechnik GmbH +* +* (C) Copyright 2009 +* Jon Smirl <[email protected]> +* +* See file CREDITS for list of people who contributed to this +* project. +* +* This program is free software; you can redistribute it and/or +* modify it under the terms of the GNU General Public License as +* published by the Free Software Foundation; either version 2 of +* the License, or (at your option) any later version. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. ? ? ? ? See the +* GNU General Public License for more details. +* +* You should have received a copy of the GNU General Public License +* along with this program; if not, write to the Free Software +* Foundation, Inc., 59 Temple Place, Suite 330, Boston, +* MA 02111-1307 USA +*/ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#define CONFIG_BOARDINFO ? ? ? ?"phyCORE-MPC5200B-tiny" + +/*----------------------------------------------------------------------------- +High Level Configuration Options +(easy to change) +-----------------------------------------------------------------------------*/ +#define CONFIG_MPC5xxx ? ? ? ? 1 ? ? ?/* This is an MPC5xxx CPU */ +#define CONFIG_MPC5200 ? ? ? ? 1 ? ? ?/* (more precisely an MPC5200 CPU) */ +#define CONFIG_MPC5200_DDR ? ? 1 ? ? ?/* (with DDR-SDRAM) */ +#define CONFIG_PHYCORE_MPC5200B_TINY 1/* phyCORE-MPC5200B -> */ + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? /* FEC configuration and IDE */ +#define CONFIG_SYS_MPC5XXX_CLKIN 33333333/* ... running at 33.333333MHz */ +#define BOOTFLAG_COLD ? ? ? ? ?0x01 ? ?/* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM ? ? ? ? ?0x02 ? ?/* Software reboot */ + +/*----------------------------------------------------------------------------- +Serial console configuration +-----------------------------------------------------------------------------*/ +#define CONFIG_PSC_CONSOLE ? ? 3 ? ? ?/* console is on PSC3 -> */ + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? /*define gps port conf. */ + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? /* register later on to */ + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? /*enable UART function! */ +#define CONFIG_BAUDRATE ? ? ? ? ? ? ? ?115200 ?/* ... at 115200 bps */ +#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } + +/* +* Command line configuration. +*/ +#include <config_cmd_default.h> + +#define CONFIG_CMD_DATE +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_EEPROM +#define CONFIG_CMD_I2C +#define CONFIG_CMD_JFFS2 +#define CONFIG_CMD_MII +#define CONFIG_CMD_NFS +#define CONFIG_CMD_PCI + +#define ? ? ? ?CONFIG_TIMESTAMP ? ? ? ?1 ? ? ? /* Print image info with timestamp */ + +#if (TEXT_BASE == 0xFF000000) ?/* Boot low */ +#define CONFIG_SYS_LOWBOOT 1 +#endif +/* RAMBOOT will be defined automatically in memory section */ + +#define CONFIG_JFFS2_CMDLINE +#define MTDIDS_DEFAULT ? ? ? ? ? ? ? ? "nor0=physmap-flash.0" +#define MTDPARTS_DEFAULT ? ? ? "mtdparts=physmap-flash.0:256k(ubootl)," \ + ? ? ? "1792k(kernel),13312k(jffs2),256k(uboot)ro,256k(oftree),-(space)" + +/*----------------------------------------------------------------------------- +Autobooting +-----------------------------------------------------------------------------*/ +#define CONFIG_BOOTDELAY ? ? ? 3 ? ? ?/* autoboot after 3 seconds */ +#define CONFIG_ZERO_BOOTDELAY_CHECK ? ?/* allow stopping of boot process */ + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? /* even with bootdelay=0 */ +#undef CONFIG_BOOTARGS + + +#define CONFIG_PREBOOT "echo;" \ + ? ? ? "echo Type \"run bootcmd_net\" to load Kernel over TFTP and to "\ + ? ? ? ? ? ? ? "mount root filesystem over NFS;" \ + ? ? ? "echo" + +#define ? ? ? ?CONFIG_EXTRA_ENV_SETTINGS ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? \ + ? ? ? "netdev=eth0\0" ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? \ + ? ? ? "uimage=uImage-pcm030\0" ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?\ + ? ? ? "oftree=oftree-pcm030.dtb\0" ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?\ + ? ? ? "jffs2=root-pcm030.jffs2\0" ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? \ + ? ? ? "uboot=u-boot-pcm030.bin\0" ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? \ + ? ? ? "bargs_base=setenv bootargs console=ttyPSC0,$(baudrate)" ? ? ? ?\ + ? ? ? ? ? ? ? " $(mtdparts) rw\0" ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? \ + ? ? ? "bargs_flash=setenv bootargs $(bootargs) root=/dev/mtdblock2" ? \ + ? ? ? ? ? ? ? " rootfstype=jffs2\0" ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? \ + ? ? ? "bargs_nfs=setenv bootargs $(bootargs) root=/dev/nfs" ? ? ? ? ? \ + ? ? ? ? ? ? ? " ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)::" ? \ + ? ? ? ? ? ? ? "$(netdev):off nfsroot=$(serverip):$(nfsrootfs),v3,tcp\0" \ + ? ? ? "bcmd_net=run bargs_base bargs_nfs; tftpboot 0x500000 $(uimage);" \ + ? ? ? ? ? ? ? " tftp 0x400000 $(oftree); bootm 0x500000 - 0x400000\0" \ + ? ? ? "bcmd_flash=run bargs_base bargs_flash; bootm 0xff040000 - " ? ?\ + ? ? ? ? ? ? ? "0xfff40000\0" ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?\ + ? ? ? ? ? ? ? " cp.b 0x400000 0xff040000 $(filesize)\0" ? ? ? ? ? ? ? \ + ? ? ? "prg_jffs2=tftp 0x400000 $(jffs2); erase 0xff200000 0xffefffff; " \ + ? ? ? ? ? ? ? "cp.b 0x400000 0xff200000 $(filesize)\0" ? ? ? ? ? ? ? ?\ + ? ? ? "prg_oftree=tftp 0x400000 $(oftree); erase 0xfff40000 0xfff5ffff;" \ + ? ? ? ? ? ? ? " cp.b 0x400000 0xfff40000 $(filesize)\0" ? ? ? ? ? ? ? \ + ? ? ? "update=tftpboot 0x400000 $(uboot);erase 0xFFF00000 0xfff3ffff;" \ + ? ? ? ? ? ? ? " cp.b 0x400000 0xFFF00000 $(filesize)\0" ? ? ? ? ? ? ? \ + ? ? ? "unlock=yes\0" ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?\ + ? ? ? "" + +#define CONFIG_BOOTCOMMAND ? ? ? ? ? ? "run bcmd_flash" + +/*-------------------------------------------------------------------------- +IPB Bus clocking configuration. +---------------------------------------------------------------------------*/ +#define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK ? ? ? ?/* define for 133MHz speed */ + +/*------------------------------------------------------------------------- +* PCI Mapping: +* 0x40000000 - 0x4fffffff - PCI Memory +* 0x50000000 - 0x50ffffff - PCI IO Space +* -----------------------------------------------------------------------*/ +#define CONFIG_PCI ? ? ? ? ? ? ? ? ? ? 1 +#define CONFIG_PCI_PNP ? ? ? ? ? ? ? ? 1 +#define CONFIG_PCI_SCAN_SHOW ? ? ? ? ? 1 +#define CONFIG_PCI_MEM_BUS ? ? ? ? ? ? 0x40000000 +#define CONFIG_PCI_MEM_PHYS ? ? ? ? ? ?CONFIG_PCI_MEM_BUS +#define CONFIG_PCI_MEM_SIZE ? ? ? ? ? ?0x10000000 +#define CONFIG_PCI_IO_BUS ? ? ? ? ? ? ?0x50000000 +#define CONFIG_PCI_IO_PHYS ? ? ? ? ? ? CONFIG_PCI_IO_BUS +#define CONFIG_PCI_IO_SIZE ? ? ? ? ? ? 0x01000000 +#define CONFIG_SYS_XLB_PIPELINING ? ? ?1 + +/*--------------------------------------------------------------------------- +I2C configuration +---------------------------------------------------------------------------*/ +#define CONFIG_HARD_I2C 1/* I2C with hardware support */ +#define CONFIG_SYS_I2C_MODULE 2/* Select I2C module #1 or #2 */ +#define CONFIG_SYS_I2C_SPEED 100000/* 100 kHz */ +#define CONFIG_SYS_I2C_SLAVE 0x7F + +/*--------------------------------------------------------------------------- +EEPROM CAT24WC32 configuration +---------------------------------------------------------------------------*/ +#define CONFIG_SYS_I2C_EEPROM_ADDR ? ? 0x52 ? ?/* 1010100x */ +#define CONFIG_SYS_I2C_FACT_ADDR ? ? ? 0x52 ? ?/* EEPROM CAT24WC32 */ +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 ? ? ?/* Bytes of address */ +#define CONFIG_SYS_EEPROM_SIZE ? ? ? ? 2048 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 15 + +/*--------------------------------------------------------------------------- +RTC configuration +---------------------------------------------------------------------------*/ +#define RTC +#define CONFIG_RTC_PCF8563 ? ? ? ? ? ? 1 +#define CONFIG_SYS_I2C_RTC_ADDR ? ? ? ? ? ? ? ?0x51 + +/*--------------------------------------------------------------------------- +Flash configuration +---------------------------------------------------------------------------*/ + +#define CONFIG_SYS_FLASH_BASE ? ? ? ? ?0xff000000 +#define CONFIG_SYS_FLASH_SIZE ? ? ? ? ?0x01000000 +#define CONFIG_SYS_FLASH_BANKS_LIST ? ?{ CONFIG_SYS_FLASH_BASE } + +#define CONFIG_SYS_FLASH_CFI ? ? ? ? ? 1 ? ? ?/* Flash is CFI conformant */ +#define CONFIG_FLASH_CFI_DRIVER ? ? ? ?1 ? ? ?/* Use the common driver */ +#define CONFIG_SYS_FLASH_EMPTY_INFO +#define CONFIG_SYS_MAX_FLASH_SECT 260/* max num of sects on one chip */ +#define CONFIG_SYS_MAX_FLASH_BANKS 1/* max num of flash banks */ + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? /* (= chip selects) */ +#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE + +/* +* Use also hardware protection. This seems required, as the BDI uses +* hardware protection. Without this, U-Boot can't work with this sectors, +* as its protection is software only by default +*/ +#define CONFIG_SYS_FLASH_PROTECTION ? ?1 + +/*--------------------------------------------------------------------------- +Environment settings +---------------------------------------------------------------------------*/ + +/* pcm030 ships with environment is EEPROM by default */ +#define CONFIG_ENV_IS_IN_EEPROM ? ? ? ?1 +#define CONFIG_ENV_OFFSET ? ? ?0x00 ? ?/* environment starts at the */ + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? /*beginning of the EEPROM */ +#define CONFIG_ENV_SIZE ? ? ? ? ? ? ? ?CONFIG_SYS_EEPROM_SIZE + +#define CONFIG_ENV_OVERWRITE ? 1 + +/*----------------------------------------------------------------------------- +?Memory map +-----------------------------------------------------------------------------*/ +#define CONFIG_SYS_MBAR ? ? ? ?0xF0000000 ? ? ?/* MBAR has to be switched by other */ + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? /* bootloader or debugger config */ +#define CONFIG_SYS_SDRAM_BASE ? ? ? ? ?0x00000000 +#define CONFIG_SYS_DEFAULT_MBAR ? ? ? ? ? ? ? ?0x80000000 +/* Use SRAM until RAM will be available */ +#define CONFIG_SYS_INIT_RAM_ADDR ? ? ? MPC5XXX_SRAM +#define CONFIG_SYS_INIT_RAM_END ? ? ? ? ? ? ? ?MPC5XXX_SRAM_SIZE ? ? ?/* End of used */ + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? /* area in DPRAM */ +#define CONFIG_SYS_GBL_DATA_SIZE ? ? ? 128 ? ?/* size in bytes */ + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? /* reserved for initial data */ +#define CONFIG_SYS_GBL_DATA_OFFSET ? ? (CONFIG_SYS_INIT_RAM_END - \ + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET ? ? ?CONFIG_SYS_GBL_DATA_OFFSET + +#define CONFIG_SYS_MONITOR_BASE ? ? ? ?TEXT_BASE +#if (CONFIG_SYS_MONITOR_BASE <CONFIG_SYS_FLASH_BASE ) +# ? ? ?define CONFIG_SYS_RAMBOOT ? ? ? ? ? ? ? 1 +#endif + +#define CONFIG_SYS_MONITOR_LEN (192 << 10)/* Reserve 192 kB for Monitor */ +#define CONFIG_SYS_MALLOC_LEN (128 << 10)/* Reserve 128 kB for malloc() */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20)/* Initial Memory map for Linux */ + +/*----------------------------------------------------------------------------- +Ethernet configuration +-----------------------------------------------------------------------------*/ +#define CONFIG_MPC5xxx_FEC ? ? ? ? ? ? 1 +#define CONFIG_MPC5xxx_FEC_MII100 +#define CONFIG_PHY_ADDR ? ? ? ? ? ? ? ? ? ? ? ?0x01 + +/*--------------------------------------------------------------------------- +GPIO configuration +---------------------------------------------------------------------------*/ + +/* GPIO port configuration +* +* Pin mapping: +* +* [29:31] = 01x +* PSC1_0 -> AC97 SDATA out +* PSC1_1 -> AC97 SDTA in +* PSC1_2 -> AC97 SYNC out +* PSC1_3 -> AC97 bitclock out +* PSC1_4 -> AC97 reset out +* +* [25:27] = 001 +* PSC2_0 -> CAN 1 Tx out +* PSC2_1 -> CAN 1 Rx in +* PSC2_2 -> CAN 2 Tx out +* PSC2_3 -> CAN 2 Rx in +* PSC2_4 -> GPIO (claimed for ATA reset, active low) +* +* +* [20:23] = 1100 +* PSC3_0 -> UART Tx out +* PSC3_1 -> UART Rx in +* PSC3_2 -> UART RTS (in/out FIXME) +* PSC3_3 -> UART CTS (in/out FIXME) +* PSC3_4 -> LocalPlus Bus CS6 \ +* PSC3_5 -> LocalPlus Bus CS7 / --> see [4] and [5] +* PSC3_6 -> dedicated SPI MOSI out (master case) +* PSC3_7 -> dedicated SPI MISO in (master case) +* PSC3_8 -> dedicated SPI SS out (master case) +* PSC3_9 -> dedicated SPI CLK out (master case) +* +* [18:19] = 01 +* USB_0 -> USB OE out +* USB_1 -> USB Tx- out +* USB_2 -> USB Tx+ out +* USB_3 -> USB RxD (in/out FIXME) +* USB_4 -> USB Rx+ in +* USB_5 -> USB Rx- in +* USB_6 -> USB PortPower out +* USB_7 -> USB speed out +* USB_8 -> USB suspend (in/out FIXME) +* USB_9 -> USB overcurrent in +* +* [17] = 0 +* USB differential mode +* +* [16] = 0 +* PCI enabled +* +* [12:15] = 0101 +* ETH_0 -> ETH Txen +* ETH_1 -> ETH TxD0 +* ETH_2 -> ETH TxD1 +* ETH_3 -> ETH TxD2 +* ETH_4 -> ETH TxD3 +* ETH_5 -> ETH Txerr +* ETH_6 -> ETH MDC +* ETH_7 -> ETH MDIO +* ETH_8 -> ETH RxDv +* ETH_9 -> ETH RxCLK +* ETH_10 -> ETH Collision +* ETH_11 -> ETH TxD +* ETH_12 -> ETH RxD0 +* ETH_13 -> ETH RxD1 +* ETH_14 -> ETH RxD2 +* ETH_15 -> ETH RxD3 +* ETH_16 -> ETH Rxerr +* ETH_17 -> ETH CRS +* +* [9:11] = 101 +* PSC6_0 -> UART RxD in +* PSC6_1 -> UART CTS (in/out FIXME) +* PSC6_2 -> UART TxD out +* PSC6_3 -> UART RTS (in/out FIXME) +* +* [2:3/6:7] = 00/11 +* TMR_0 -> ATA_CS0 out +* TMR_1 -> ATA_CS1 out +* TMR_2 -> GPIO +* TMR_3 -> GPIO +* TMR_4 -> GPIO +* TMR_5 -> GPIO +* TMR_6 -> GPIO +* TMR_7 -> GPIO +* I2C_0 -> I2C 1 Clock out +* I2C_1 -> I2C 1 IO in/out +* I2C_2 -> I2C 2 Clock out +* I2C_3 -> I2C 2 IO in/out +* +* [4] = 1 +* PSC3_5 is used as CS7 +* +* [5] = 1 +* PSC3_4 is used as CS6 +* +* [1] = 0 +* gpio_wkup_7 is GPIO +* +* [0] = 0 +* gpio_wkup_6 is GPIO +* +*/ +#define CONFIG_SYS_GPS_PORT_CONFIG ? ? 0x0f551c12 + +/*----------------------------------------------------------------------------- +Miscellaneous configurable options +-------------------------------------------------------------------------------*/ +#define CONFIG_SYS_LONGHELP ? ?/* undef to save memory */ +#define CONFIG_SYS_PROMPT "uboot> "/* Monitor Command Prompt */ + +#define CONFIG_CMDLINE_EDITING 1/* add command line history */ + +#define CONFIG_SYS_CACHELINE_SIZE 32/* For MPC5xxx CPUs */ +#if defined(CONFIG_CMD_KGDB ) +#define CONFIG_SYS_CACHELINE_SHIFT 5/* log base 2 of the above value */ +#endif + +#if defined(CONFIG_CMD_KGDB ) +#define CONFIG_SYS_CBSIZE 1024/* Console I/O Buffer Size */ +#else +#define CONFIG_SYS_CBSIZE 256/* Console I/O Buffer Size */ +#endif +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16/* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */ + +#define CONFIG_SYS_MEMTEST_START 0x00100000/* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x00f00000/* 1 ... 15 MB in DRAM */ + +#define CONFIG_SYS_LOAD_ADDR 0x400000/* default load address */ +#define CONFIG_SYS_HZ 1000/* decrementer freq: 1 ms ticks */ + +#define CONFIG_DISPLAY_BOARDINFO 1 + +/*----------------------------------------------------------------------------- +Various low-level settings +-----------------------------------------------------------------------------*/ +#define CONFIG_SYS_HID0_INIT ? ? ? ? ? HID0_ICE | HID0_ICFI +#define CONFIG_SYS_HID0_FINAL ? ? ? ? ?HID0_ICE + +/* no burst access on the LPB */ +#define CONFIG_SYS_CS_BURST ? ? ? ? ? ?0x00000000 +/* one deadcycle for the 33MHz statemachine */ +#define CONFIG_SYS_CS_DEADCYCLE ? ? ? ? ? ? ? ?0x33333331 +/* one additional waitstate for the 33MHz statemachine */ +#define CONFIG_SYS_BOOTCS_CFG ? ? ? ? ?0x0001dd00 +#define CONFIG_SYS_BOOTCS_START ? ? ? ? ? ? ? ?CONFIG_SYS_FLASH_BASE +#define CONFIG_SYS_BOOTCS_SIZE ? ? ? ? CONFIG_SYS_FLASH_SIZE + +#define CONFIG_SYS_RESET_ADDRESS ? ? ? 0xff000000 + +/*----------------------------------------------------------------------- +* USB stuff +*----------------------------------------------------------------------- +*/ +#define CONFIG_USB_CLOCK ? ? ? ? ? ? ? 0x0001BBBB +#define CONFIG_USB_CONFIG ? ? ? ? ? ? ?0x00001000 + +/*--------------------------------------------------------------------------- +IDE/ATA stuff Supports IDE harddisk +----------------------------------------------------------------------------*/ + +#undef ?CONFIG_IDE_8xx_PCCARD ?/* Use IDE with PC Card Adapter */ +#undef CONFIG_IDE_8xx_DIRECT ?/* Direct IDE not supported */ +#undef CONFIG_IDE_LED ? ? ? ? ?/* LED for ide not supported */ +#define CONFIG_SYS_ATA_CS_ON_TIMER01 +#define ? ? ? ?CONFIG_IDE_RESET 1 ? ? ?/* reset for ide supported */ +#define CONFIG_IDE_PREINIT +#define CONFIG_SYS_IDE_MAXBUS 1/* max. 1 IDE bus */ +#define CONFIG_SYS_IDE_MAXDEVICE 2/* max. 2 drives per IDE bus */ +#define CONFIG_SYS_ATA_IDE0_OFFSET ? ? 0x0000 +#define CONFIG_SYS_ATA_BASE_ADDR ? ? ? MPC5XXX_ATA +/* Offset for data I/O ? ? ? ? ? ? ? ? */ +#define CONFIG_SYS_ATA_DATA_OFFSET ? ? (0x0060) +/* Offset for normal register accesses */ +#define CONFIG_SYS_ATA_REG_OFFSET ? ? ?(CONFIG_SYS_ATA_DATA_OFFSET) +/* Offset for alternate registers ? ? ?*/ +#define CONFIG_SYS_ATA_ALT_OFFSET ? ? ?(0x005C) +/* Interval between registers */ +#define CONFIG_SYS_ATA_STRIDE ? ? ? ? ?4 +#define CONFIG_ATAPI ? ? ? ? ? ? ? ? ? 1 + +/* we enable IDE and FAT support, so we also need partition support */ +#define CONFIG_DOS_PARTITION 1 + +/* USB */ +#define CONFIG_USB_OHCI +#define CONFIG_USB_STORAGE + +/* pass open firmware flat tree */ +#define CONFIG_OF_LIBFDT ? ? ? ? ? ? ? 1 +#define CONFIG_OF_BOARD_SETUP ? ? ? ? ?1 + +#define OF_CPU ? ? ? ? ? ? ? ? ? ? ? ? "PowerPC,5200 at 0" +#define OF_TBCLK ? ? ? ? ? ? ? ? ? ? ? CONFIG_SYS_MPC5XXX_CLKIN +#define OF_SOC ? ? ? ? ? ? ? ? ? ? ? ? "soc5200 at f0000000" +#define OF_STDOUT_PATH ? ? ? ? ? ? ? ? "/soc5200 at f0000000/serial at 2400" + +#endif /* __CONFIG_H */
Signature · 2 lines
Jon Smirl jonsmirl at gmail.com
PATCH v6 1/1 board support patch for phyCORE-MPC5200B-tiny
In reply to Jon SmirlDear Jon Smirl,
Quoted 14 lines · In message <20090614222128.12604.33392.stgit@terra> you wrote:
Add support for the Phytec phyCORE-MPC5200B-tiny. Code originally from Pengutronix.de. Created
CONFIG_SYS_ATA_CS_ON_TIMER01define for when IDE CS is on Timer 0/1Signed-off-by Jon Smirl <[email protected]>--- MAINTAINERS | 4 MAKEALL | 1 Makefile | 9 + board/phytec/pcm030/Makefile | 50 ++++ board/phytec/pcm030/config.mk | 41 +++ board/phytec/pcm030/mt46v32m16-75.h | 37 +++ board/phytec/pcm030/pcm030.c | 220 +++++++++++++++++ cpu/mpc5xxx/ide.c | 3 doc/README.phytec.pcm030 | 46 ++++
Quoted 8 lines
include/configs/pcm030.h | 444 +++++++++++++++++++++++++++++++++++ 10 files changed, 855 insertions(+), 0 deletions(-) create mode 100644 board/phytec/pcm030/Makefile create mode 100644 board/phytec/pcm030/config.mk create mode 100644 board/phytec/pcm030/mt46v32m16-75.h create mode 100644 board/phytec/pcm030/pcm030.c create mode 100644 doc/README.phytec.pcm030 create mode 100644 include/configs/pcm030.h
Applied to u-boot-mpc5xxx repo, thanks.
Best regards,
Wolfgang Denk
Signature · 6 lines
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de Looks clean and obviously correct to me, but then _everything_ I write always looks obviously correct to me. - Linus Torvalds in <[email protected]>