v2.6.31-rc patches - Part 3: other fixes and changes
Subsystems (3)
Hi Linus,
Please pull from 'master' branch of
git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog.git
or if master.kernel.org hasn't synced up yet:
master.kernel.org:/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog.git
This will update the following files:
Documentation/watchdog/hpwdt.txt | 19 ++++-- drivers/watchdog/Kconfig | 18 +---- drivers/watchdog/hpwdt.c | 26 ++++++-- drivers/watchdog/omap_wdt.c | 7 ++ drivers/watchdog/wdt_pci.c | 122 +++++++++++++++++++-------------------- 5 files changed, 109 insertions(+), 83 deletions(-)
with these Changes:
Author: Wim Van Sebroeck <[email protected]> Date: Fri Jun 19 09:32:57 2009 +0000
[WATCHDOG] wdt_pci.c: remove #ifdef CONFIG_WDT_501_PCI
Change the wdt_pci.c watchdog driver so that the code is the same for both the PCI-WDT500 as the PCI-WDT501 card. The selection of the card is now being done via the module parameter: 'type' instead of the config option CONFIG_WDT_501_PCI.
Author: Tom Mingarelli <[email protected]> Date: Thu Jun 18 23:28:57 2009 +0000
[WATCHDOG] hpwdt: Add NMI priority option
Add a priority option so that the user can choose if we do the NMI first or last.
Author: Ulrik Bech Hald <[email protected]> Date: Fri Jun 12 16:18:32 2009 -0500
[WATCHDOG] OMAP fixes: enable clock in probe, trigger timer reload
This patch contains two fixes:
1)In omap_wdt_probe() the watchdog is reset and disabled. This requires register access and the clks needs to be enabled temporarily
2)In omap_wdt_open() the timer register needs to be reloaded to trigger a new timer value (the default of 60s)
Tested on OMAP34xx platform (Zoom1)
The Changes can also be looked at on:
http://www.kernel.org/git/?p=linux/kernel/git/wim/linux-2.6-watchdog.git;a=summary
For completeness, I added the overal diff below.
Greetings,
Wim.
================================================================================
Documentation/watchdog/hpwdt.txt +15 -4
@@ -19,30 +19,41 @@ Last reviewed: 06/02/2009 not be updated in a timely fashion and a hardware system reset (also known as an Automatic Server Recovery (ASR)) event will occur. - The hpwdt driver also has three (3) module parameters. They are the following: + The hpwdt driver also has four (4) module parameters. They are the following: soft_margin - allows the user to set the watchdog timer value allow_kdump - allows the user to save off a kernel dump image after an NMI nowayout - basic watchdog parameter that does not allow the timer to be restarted or an impending ASR to be escaped. + priority - determines whether or not the hpwdt driver is first on the + die_notify list to handle NMIs or last. The default value + for this module parameter is 0 or LAST. If the user wants to + enable NMI sourcing then reload the hpwdt driver with + priority=1 (and boot with nmi_watchdog=0). NOTE: More information about watchdog drivers in general, including the ioctl interface to /dev/watchdog can be found in Documentation/watchdog/watchdog-api.txt and Documentation/IPMI.txt. - The NMI sourcing capability is disabled when the driver discovers that the - nmi_watchdog is turned on (nmi_watchdog = 1). This is due to the inability to + The priority parameter was introduced due to other kernel software that relied + on handling NMIs (like oprofile). Keeping hpwdt's priority at 0 (or LAST) + enables the users of NMIs for non critical events to be work as expected. + + The NMI sourcing capability is disabled by default due to the inability to distinguish between "NMI Watchdog Ticks" and "HW generated NMI events" in the Linux kernel. What this means is that the hpwdt nmi handler code is called each time the NMI signal fires off. This could amount to several thousands of NMIs in a matter of seconds. If a user sees the Linux kernel's "dazed and confused" message in the logs or if the system gets into a hung state, then - the user should reboot with nmi_watchdog=0. + the hpwdt driver can be reloaded with the "priority" module parameter set + (priority=1). 1. If the kernel has not been booted with nmi_watchdog turned off then edit /boot/grub/menu.lst and place the nmi_watchdog=0 at the end of the currently booting kernel line. 2. reboot the sever + 3. Once the system comes up perform a rmmod hpwdt + 4. insmod /lib/modules/`uname -r`/kernel/drivers/char/watchdog/hpwdt.ko priority=1 Now, the hpwdt can successfully receive and source the NMI and provide a log message that details the reason for the NMI (as determined by the HP BIOS).
drivers/watchdog/Kconfig +5 -13
@@ -1007,24 +1007,16 @@ config WDTPCI ---help--- If you have a PCI-WDT500/501 watchdog board, say Y here, otherwise N. - To compile this driver as a module, choose M here: the - module will be called wdt_pci. - -config WDT_501_PCI - bool "PCI-WDT501 features" - depends on WDTPCI - help - Saying Y here and creating a character special file /dev/temperature - with major number 10 and minor number 131 ("man mknod") will give - you a thermometer inside your computer: reading from - /dev/temperature yields one byte, the temperature in degrees - Fahrenheit. This works only if you have a PCI-WDT501 watchdog board - installed. + If you have a PCI-WDT501 watchdog board then you can enable the + temperature sensor by setting the type parameter to 501. If you want to enable the Fan Tachometer on the PCI-WDT501, then you can do this via the tachometer parameter. Only do this if you have a fan tachometer actually set up. + To compile this driver as a module, choose M here: the + module will be called wdt_pci. + # # USB-based Watchdog Cards #
drivers/watchdog/hpwdt.c +21 -5
@@ -120,7 +120,8 @@ static int nowayout = WATCHDOG_NOWAYOUT;static char expect_release;static unsigned long hpwdt_is_open;static unsigned int allow_kdump; -static int hpwdt_nmi_sourcing; +static unsigned int hpwdt_nmi_sourcing; +static unsigned int priority;/* hpwdt at end of die_notify list */ static void __iomem *pci_mem_addr;/* the PCI-memory address */ static unsigned long __iomem *hpwdt_timer_reg;
@@ -623,7 +624,7 @@ static struct miscdevice hpwdt_miscdev = {static struct notifier_block die_notifier = { .notifier_call = hpwdt_pretimeout, - .priority =0x7FFFFFFF , + .priority =0 , };/*
@@ -641,7 +642,8 @@ static void __devinit hpwdt_check_nmi_sourcing(struct pci_dev *dev) hpwdt_nmi_sourcing =1 ; else dev_warn(&dev->dev, "NMI sourcing is disabled. To enable this " - "functionality you must reboot with nmi_watchdog=0.\n"); +"functionality you must reboot with nmi_watchdog=0 " + "and load the hpwdt driver with priority=1.\n"); }#else static void __devinit hpwdt_check_nmi_sourcing (struct pci_dev *dev)
@@ -714,6 +716,14 @@ static int __devinit hpwdt_init_one(struct pci_dev *dev, cmn_regs.u1.rah =0x0D ; cmn_regs.u1.ral =0x02 ; +/* +* If the priority is set to 1, then we will be put first on the +* die notify list to handle a critical NMI. The default is to +* be last so other users of the NMI signal can function. +*/ +if (priority) + die_notifier.priority =0x7FFFFFFF ; + retval =register_die_notifier (&die_notifier);if (retval !=0 ) { dev_warn(&dev->dev,
@@ -733,9 +743,11 @@ static int __devinit hpwdt_init_one(struct pci_dev *dev,printk (KERN_INFO "hp Watchdog Timer Driver: %s" ", timer margin: %d seconds (nowayout=%d)" -", allow kernel dump: %s (default = 0/OFF).\n" , +", allow kernel dump: %s (default = 0/OFF)" +", priority: %s (default = 0/LAST).\n" ,HPWDT_VERSION , soft_margin, nowayout, - (allow_kdump ==0 ) ?"OFF" :"ON" ); + (allow_kdump ==0 ) ?"OFF" :"ON" , + (priority ==0 ) ?"LAST" :"FIRST" );return 0 ;
@@ -798,5 +810,9 @@ module_param(nowayout, int, 0); MODULE_PARM_DESC(nowayout, "Watchdog cannot be stopped once started (default=" __MODULE_STRING(WATCHDOG_NOWAYOUT) ")"); +module_param (priority, int,0 ); +MODULE_PARM_DESC (priority,"The hpwdt driver handles NMIs first or last" +" (default = 0/Last)\n" ); +module_init (hpwdt_init);module_exit (hpwdt_cleanup);
drivers/watchdog/omap_wdt.c +7 -0
@@ -159,6 +159,7 @@ static int omap_wdt_open(struct inode *inode, struct file *file) file->private_data = (void *) wdev;omap_wdt_set_timeout (wdev); +omap_wdt_ping (wdev);/* trigger loading of new timeout value */ omap_wdt_enable (wdev);return nonseekable_open (inode, file);
@@ -313,6 +314,9 @@ static int __devinit omap_wdt_probe(struct platform_device *pdev)platform_set_drvdata (pdev, wdev); +clk_enable (wdev->ick); +clk_enable (wdev->fck); +omap_wdt_disable (wdev);omap_wdt_adjust_timeout (timer_margin);
@@ -332,6 +336,9 @@ static int __devinit omap_wdt_probe(struct platform_device *pdev)/* autogate OCP interface clock */ __raw_writel (0x01 , wdev->base +OMAP_WATCHDOG_SYS_CONFIG ); +clk_disable (wdev->ick); +clk_disable (wdev->fck); + omap_wdt_dev = pdev;return 0 ;
drivers/watchdog/wdt_pci.c +61 -61
244 lines not on this page · raw message