Skip to contentSkip to conversation

ppc4xx: Move 405EP pci code from cpu_init_f() to __pci_pre_init()

PATCH New Matthias Fuchs 2 participants 2 messages Jul 8, 2009 – Jul 10, 2009

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 ppc4xx: Move 405EP pci code from cpu_init_f() to __pci_pre_init()

This patch moves some basic PCI initialisation from the 4xx cpu_init_f() to cpu/ppc4xx/4xx_pci.c.

The original cpu_init_f() function enabled the 405EP's internal arbiter in all situations. Also the HCE bit in cpc0_pci is always set. The first is not really wanted for PCI adapter designs and the latter is a general bug for PCI adapter U-Boots. Because it enables PCI configuration by the system CPU even when the PCI configuration has not been setup by the 405EP. The one and only correct place is in pci_405gp_init() (see "Set HCE bit" comment).

So for compatibility reasons the arbiter is still enabled in any case, but from weak pci_pre_init() so that it can be replaced by board specific code.

---
 cpu/ppc4xx/4xx_pci.c  |   14 ++++++++++++++
 cpu/ppc4xx/cpu_init.c |    5 -----
 2 files changed, 14 insertions(+), 5 deletions(-)
cpu/ppc4xx/4xx_pci.c +14 -0
index 31ca85d..33dd743 100644
@@ -87,6 +87,20 @@ DECLARE_GLOBAL_DATA_PTR;
  */
 int __pci_pre_init(struct pci_controller *hose)
 {
+#if defined (CONFIG_405EP)
+	/*
+	 * Enable the internal PCI arbiter by default.
+	 *
+	 * On 405EP CPUs the internal arbiter can be controlled
+	 * by the I2C strapping EEPROM. If you want to do so
+	 * or if you want to disable the arbiter pci_pre_init()
+	 * must be reimplemented without enabling the arbiter.
+	 * The arbiter is enabled in this place because of
+	 * compatibility reasons.
+	 */
+	mtdcr(cpc0_pci, mfdcr(cpc0_pci) | CPC0_PCI_ARBIT_EN);
+#endif /* CONFIG_405EP */
+
 	return 1;
 }
 int pci_pre_init(struct pci_controller *hose) __attribute__((weak, alias("__pci_pre_init")));
cpu/ppc4xx/cpu_init.c +0 -5
index 577d33f..bbd795d 100644
@@ -174,11 +174,6 @@ cpu_init_f (void)
 	 * Set EMAC noise filter bits
 	 */
 	mtdcr(cpc0_epctl, CPC0_EPRCSR_E0NFE | CPC0_EPRCSR_E1NFE);
-
-	/*
-	 * Enable the internal PCI arbiter
-	 */
-	mtdcr(cpc0_pci, mfdcr(cpc0_pci) | CPC0_PCI_HOST_CFG_EN | CPC0_PCI_ARBIT_EN);
 #endif /* CONFIG_405EP */
 
 #if defined(CONFIG_SYS_4xx_GPIO_TABLE)
Signature · 1 line
1.6.1
#1 lore raw

PATCH 1/1 ppc4xx: Move 405EP pci code from cpu_init_f() to __pci_pre_init()

Quoted 11 lines · On Wednesday 08 July 2009 13:43:55 Matthias Fuchs wrote:

This patch moves some basic PCI initialisation from the 4xx cpu_init_f() to cpu/ppc4xx/4xx_pci.c.

The original cpu_init_f() function enabled the 405EP's internal arbiter in all situations. Also the HCE bit in cpc0_pci is always set. The first is not really wanted for PCI adapter designs and the latter is a general bug for PCI adapter U-Boots. Because it enables PCI configuration by the system CPU even when the PCI configuration has not been setup by the 405EP. The one and only correct place is in pci_405gp_init() (see "Set HCE bit" comment).

Quoted 5 lines

So for compatibility reasons the arbiter is still enabled in any case, but from weak pci_pre_init() so that it can be replaced by board specific code.

Applied to u-boot-ppc4xx. Thanks.

Best regards,
Stefan

=====================================================================
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office at denx.de
=====================================================================