Skip to contentSkip to conversation

Fixes for OMAP2/3 SDRC/clock for 2.6.31-rc*

PATCH New Paul Walmsley 1 participant 9 messages Jul 25, 2009

Subsystems (4)
lore
Share & tools
lore

Paul Walmsley

author maintainer
#0 lore raw

cover Fixes for OMAP2/3 SDRC/clock for 2.6.31-rc*

This series contains fixes for 2.6.31-rc* for the OMAP2/3 SDRC SDRAM controller and the OMAP2/3 clock code.

Boot-tested on BeagleBoard rev C2 and N800. Additional CORE DVFS testing run on BeagleBoard rev C2.

- Paul

---

size:
text data bss dec hex filename
3451158 197824 104656 3753638 3946a6 vmlinux.beagle.orig
3452322 198592 104656 3755570 394e32 vmlinux.beagle

Jean Pihet (2):
OMAP3 SDRC: add support for 2 SDRAM chip selects
OMAP3: Setup MUX settings for SDRC CKE signals

Paul Walmsley (4):
OMAP2/3 SDRC: don't set SDRC_POWER.PWDENA on boot OMAP2/3 clock: split, rename omap2_wait_clock_ready() OMAP2 clock: 2430 I2CHS uses non-standard CM_IDLEST register OMAP3 clock: correct module IDLEST bits: SSI; DSS; USBHOST; HSOTGUSB

Rajendra Nayak (2):
OMAP3 SDRC: Fix freeze when scaling CORE dpll to < 83Mhz OMAP3 SDRC: Move the clk stabilization delay to the right place

 arch/arm/mach-omap2/board-2430sdp.c      |    2 
 arch/arm/mach-omap2/board-3430sdp.c      |    2 
 arch/arm/mach-omap2/board-4430sdp.c      |    2 
 arch/arm/mach-omap2/board-apollon.c      |    2 
 arch/arm/mach-omap2/board-generic.c      |    2 
 arch/arm/mach-omap2/board-h4.c           |    2 
 arch/arm/mach-omap2/board-ldp.c          |    2 
 arch/arm/mach-omap2/board-omap3beagle.c  |    7 +
 arch/arm/mach-omap2/board-omap3evm.c     |    2 
 arch/arm/mach-omap2/board-omap3pandora.c |    8 +-
 arch/arm/mach-omap2/board-overo.c        |    8 +-
 arch/arm/mach-omap2/board-rx51.c         |    6 +
 arch/arm/mach-omap2/board-zoom2.c        |    2 
 arch/arm/mach-omap2/clock.c              |  156 +++++++++++++++---------------
 arch/arm/mach-omap2/clock.h              |    6 +
 arch/arm/mach-omap2/clock24xx.c          |   37 +++++++
 arch/arm/mach-omap2/clock24xx.h          |    4 -
 arch/arm/mach-omap2/clock34xx.c          |  155 +++++++++++++++++++++++++++---
 arch/arm/mach-omap2/clock34xx.h          |   85 ++++++++++++++--
 arch/arm/mach-omap2/io.c                 |    5 +
 arch/arm/mach-omap2/mux.c                |    6 +
 arch/arm/mach-omap2/prcm.c               |   43 ++++++++
 arch/arm/mach-omap2/sdrc.c               |   68 +++++++++----
 arch/arm/mach-omap2/sram34xx.S           |  143 +++++++++++++++++++++-------
 arch/arm/plat-omap/include/mach/clock.h  |    2 
 arch/arm/plat-omap/include/mach/io.h     |    3 -
 arch/arm/plat-omap/include/mach/mux.h    |    4 +
 arch/arm/plat-omap/include/mach/prcm.h   |    1 
 arch/arm/plat-omap/include/mach/sdrc.h   |   11 ++
 arch/arm/plat-omap/include/mach/sram.h   |   23 ++--
 arch/arm/plat-omap/sram.c                |   30 +++---
 31 files changed, 623 insertions(+), 206 deletions(-)
author maintainer
#1 lore raw

PATCH 1/8 OMAP3 SDRC: add support for 2 SDRAM chip selects

From: Jean Pihet <[email protected]>

Some OMAP3 boards (Beagle Cx, Overo, RX51, Pandora) have 2 SDRAM parts connected to the SDRC.

This patch adds the following:
- add a new argument of type omap_sdrc_params struct* to omap2_init_common_hw and omap2_sdrc_init for the 2nd CS params
- adapted the OMAP boards files to the new prototype of omap2_init_common_hw
- add the SDRC 2nd CS registers offsets defines
- adapt the sram sleep code to configure the SDRC for the 2nd CS

Note: If the 2nd param to omap2_init_common_hw is NULL, then the parameters are not programmed into the SDRC CS1 registers

Tested on 3430 SDP and Beagleboard rev C2 and B5, with suspend/resume and frequency changes (cpufreq).

---
 arch/arm/mach-omap2/board-2430sdp.c      |    2 
 arch/arm/mach-omap2/board-3430sdp.c      |    2 
 arch/arm/mach-omap2/board-4430sdp.c      |    2 
 arch/arm/mach-omap2/board-apollon.c      |    2 
 arch/arm/mach-omap2/board-generic.c      |    2 
 arch/arm/mach-omap2/board-h4.c           |    2 
 arch/arm/mach-omap2/board-ldp.c          |    2 
 arch/arm/mach-omap2/board-omap3beagle.c  |    3 -
 arch/arm/mach-omap2/board-omap3evm.c     |    2 
 arch/arm/mach-omap2/board-omap3pandora.c |    3 -
 arch/arm/mach-omap2/board-overo.c        |    3 -
 arch/arm/mach-omap2/board-rx51.c         |    2 
 arch/arm/mach-omap2/board-zoom2.c        |    2 
 arch/arm/mach-omap2/clock34xx.c          |   37 ++++++--
 arch/arm/mach-omap2/io.c                 |    5 +
 arch/arm/mach-omap2/sdrc.c               |   63 +++++++++-----
 arch/arm/mach-omap2/sram34xx.S           |  137 +++++++++++++++++++++++-------
 arch/arm/plat-omap/include/mach/io.h     |    3 -
 arch/arm/plat-omap/include/mach/sdrc.h   |   11 ++
 arch/arm/plat-omap/include/mach/sram.h   |   23 +++--
 arch/arm/plat-omap/sram.c                |   30 ++++---
 21 files changed, 236 insertions(+), 102 deletions(-)
arch/arm/mach-omap2/board-2430sdp.c +1 -1
index 9c3fdcd..8ec2a13 100644
@@ -141,7 +141,7 @@ static inline void board_smc91x_init(void)
 
 static void __init omap_2430sdp_init_irq(void)
 {
-	omap2_init_common_hw(NULL);
+	omap2_init_common_hw(NULL, NULL);
 	omap_init_irq();
 	omap_gpio_init();
 }
arch/arm/mach-omap2/board-3430sdp.c +1 -1
index 496a90e..ac262cd 100644
@@ -169,7 +169,7 @@ static struct platform_device *sdp3430_devices[] __initdata = {
 
 static void __init omap_3430sdp_init_irq(void)
 {
-	omap2_init_common_hw(hyb18m512160af6_sdrc_params);
+	omap2_init_common_hw(hyb18m512160af6_sdrc_params, NULL);
 	omap_init_irq();
 	omap_gpio_init();
 }
arch/arm/mach-omap2/board-4430sdp.c +1 -1
index 57e477b..b0c7402 100644
@@ -59,7 +59,7 @@ static void __init gic_init_irq(void)
 
 static void __init omap_4430sdp_init_irq(void)
 {
-	omap2_init_common_hw(NULL);
+	omap2_init_common_hw(NULL, NULL);
 #ifdef CONFIG_OMAP_32K_TIMER
 	omap2_gp_clockevent_set_gptimer(1);
 #endif
arch/arm/mach-omap2/board-apollon.c +1 -1
index 06dfba8..dcfc20d 100644
@@ -250,7 +250,7 @@ out:
 
 static void __init omap_apollon_init_irq(void)
 {
-	omap2_init_common_hw(NULL);
+	omap2_init_common_hw(NULL, NULL);
 	omap_init_irq();
 	omap_gpio_init();
 	apollon_init_smc91x();
arch/arm/mach-omap2/board-generic.c +1 -1
index 3492162..fd00aa0 100644
@@ -33,7 +33,7 @@
 
 static void __init omap_generic_init_irq(void)
 {
-	omap2_init_common_hw(NULL);
+	omap2_init_common_hw(NULL, NULL);
 	omap_init_irq();
 }
 
arch/arm/mach-omap2/board-h4.c +1 -1
index e7d017c..7b1d61d 100644
@@ -270,7 +270,7 @@ static void __init h4_init_flash(void)
 
 static void __init omap_h4_init_irq(void)
 {
-	omap2_init_common_hw(NULL);
+	omap2_init_common_hw(NULL, NULL);
 	omap_init_irq();
 	omap_gpio_init();
 	h4_init_flash();
arch/arm/mach-omap2/board-ldp.c +1 -1
index d8bc0a7..ea383f8 100644
@@ -270,7 +270,7 @@ static inline void __init ldp_init_smsc911x(void)
 
 static void __init omap_ldp_init_irq(void)
 {
-	omap2_init_common_hw(NULL);
+	omap2_init_common_hw(NULL, NULL);
 	omap_init_irq();
 	omap_gpio_init();
 	ldp_init_smsc911x();
arch/arm/mach-omap2/board-omap3beagle.c +2 -1
index 991ac9c..4abefd9 100644
@@ -282,7 +282,8 @@ static int __init omap3_beagle_i2c_init(void)
 
 static void __init omap3_beagle_init_irq(void)
 {
-	omap2_init_common_hw(mt46h32m32lf6_sdrc_params);
+	omap2_init_common_hw(mt46h32m32lf6_sdrc_params,
+			     mt46h32m32lf6_sdrc_params);
 	omap_init_irq();
 #ifdef CONFIG_OMAP_32K_TIMER
 	omap2_gp_clockevent_set_gptimer(12);
arch/arm/mach-omap2/board-omap3evm.c +1 -1
index d3cc145..217e5a2 100644
@@ -279,7 +279,7 @@ struct spi_board_info omap3evm_spi_board_info[] = {
 
 static void __init omap3_evm_init_irq(void)
 {
-	omap2_init_common_hw(mt46h32m32lf6_sdrc_params);
+	omap2_init_common_hw(mt46h32m32lf6_sdrc_params, NULL);
 	omap_init_irq();
 	omap_gpio_init();
 	omap3evm_init_smc911x();
arch/arm/mach-omap2/board-omap3pandora.c +2 -1
index e32aa23..9b991ce 100644
@@ -310,7 +310,8 @@ static int __init omap3pandora_i2c_init(void)
 
 static void __init omap3pandora_init_irq(void)
 {
-	omap2_init_common_hw(mt46h32m32lf6_sdrc_params);
+	omap2_init_common_hw(mt46h32m32lf6_sdrc_params,
+			     mt46h32m32lf6_sdrc_params);
 	omap_init_irq();
 	omap_gpio_init();
 }
arch/arm/mach-omap2/board-overo.c +2 -1
index dff5528..44bc1c5 100644
@@ -360,7 +360,8 @@ static int __init overo_i2c_init(void)
 
 static void __init overo_init_irq(void)
 {
-	omap2_init_common_hw(mt46h32m32lf6_sdrc_params);
+	omap2_init_common_hw(mt46h32m32lf6_sdrc_params,
+			     mt46h32m32lf6_sdrc_params);
 	omap_init_irq();
 	omap_gpio_init();
 }
arch/arm/mach-omap2/board-rx51.c +1 -1
index 374ff63..591ae8a 100644
@@ -61,7 +61,7 @@ static struct omap_board_config_kernel rx51_config[] = {
 
 static void __init rx51_init_irq(void)
 {
-	omap2_init_common_hw(NULL);
+	omap2_init_common_hw(NULL, NULL);
 	omap_init_irq();
 	omap_gpio_init();
 }
arch/arm/mach-omap2/board-zoom2.c +1 -1
index bcc0f76..427b7b8 100644
@@ -25,7 +25,7 @@
 
 static void __init omap_zoom2_init_irq(void)
 {
-	omap2_init_common_hw(NULL);
+	omap2_init_common_hw(NULL, NULL);
 	omap_init_irq();
 	omap_gpio_init();
 }
arch/arm/mach-omap2/clock34xx.c +28 -9
index 045da92..1c6480d 100644
@@ -725,7 +725,9 @@ static int omap3_core_dpll_m2_set_rate(struct clk *clk, unsigned long rate)
 	u32 unlock_dll = 0;
 	u32 c;
 	unsigned long validrate, sdrcrate, mpurate;
-	struct omap_sdrc_params *sp;
+	struct omap_sdrc_params *sdrc_cs0;
+	struct omap_sdrc_params *sdrc_cs1;
+	int ret;
 
 	if (!clk || !rate)
 		return -EINVAL;
@@ -743,8 +745,8 @@ static int omap3_core_dpll_m2_set_rate(struct clk *clk, unsigned long rate)
 	else
 		sdrcrate >>= ((clk->rate / rate) >> 1);
 
-	sp = omap2_sdrc_get_params(sdrcrate);
-	if (!sp)
+	ret = omap2_sdrc_get_params(sdrcrate, &sdrc_cs0, &sdrc_cs1);
+	if (ret)
 		return -EINVAL;
 
 	if (sdrcrate < MIN_SDRC_DLL_LOCK_FREQ) {
@@ -765,12 +767,29 @@ static int omap3_core_dpll_m2_set_rate(struct clk *clk, unsigned long rate)
 
 	pr_debug("clock: changing CORE DPLL rate from %lu to %lu\n", clk->rate,
 		 validrate);
-	pr_debug("clock: SDRC timing params used: %08x %08x %08x\n",
-		 sp->rfr_ctrl, sp->actim_ctrla, sp->actim_ctrlb);
-
-	omap3_configure_core_dpll(sp->rfr_ctrl, sp->actim_ctrla,
-				  sp->actim_ctrlb, new_div, unlock_dll, c,
-				  sp->mr, rate > clk->rate);
+	pr_debug("clock: SDRC CS0 timing params used:"
+		 " RFR %08x CTRLA %08x CTRLB %08x MR %08x\n",
+		 sdrc_cs0->rfr_ctrl, sdrc_cs0->actim_ctrla,
+		 sdrc_cs0->actim_ctrlb, sdrc_cs0->mr);
+	if (sdrc_cs1)
+		pr_debug("clock: SDRC CS1 timing params used: "
+		 " RFR %08x CTRLA %08x CTRLB %08x MR %08x\n",
+		 sdrc_cs1->rfr_ctrl, sdrc_cs1->actim_ctrla,
+		 sdrc_cs1->actim_ctrlb, sdrc_cs1->mr);
+
+	if (sdrc_cs1)
+		omap3_configure_core_dpll(
+				  new_div, unlock_dll, c, rate > clk->rate,
+				  sdrc_cs0->rfr_ctrl, sdrc_cs0->actim_ctrla,
+				  sdrc_cs0->actim_ctrlb, sdrc_cs0->mr,
+				  sdrc_cs1->rfr_ctrl, sdrc_cs1->actim_ctrla,
+				  sdrc_cs1->actim_ctrlb, sdrc_cs1->mr);
+	else
+		omap3_configure_core_dpll(
+				  new_div, unlock_dll, c, rate > clk->rate,
+				  sdrc_cs0->rfr_ctrl, sdrc_cs0->actim_ctrla,
+				  sdrc_cs0->actim_ctrlb, sdrc_cs0->mr,
+				  0, 0, 0, 0);
 
 	return 0;
 }
arch/arm/mach-omap2/io.c +3 -2
index 3a86b0f..e9b9bcb 100644
@@ -276,14 +276,15 @@ static int __init _omap2_init_reprogram_sdrc(void)
 	return v;
 }
 
-void __init omap2_init_common_hw(struct omap_sdrc_params *sp)
+void __init omap2_init_common_hw(struct omap_sdrc_params *sdrc_cs0,
+				 struct omap_sdrc_params *sdrc_cs1)
 {
 	omap2_mux_init();
 #ifndef CONFIG_ARCH_OMAP4 /* FIXME: Remove this once the clkdev is ready */
 	pwrdm_init(powerdomains_omap);
 	clkdm_init(clockdomains_omap, clkdm_pwrdm_autodeps);
 	omap2_clk_init();
-	omap2_sdrc_init(sp);
+	omap2_sdrc_init(sdrc_cs0, sdrc_cs1);
 	_omap2_init_reprogram_sdrc();
 #endif
 	gpmc_init();
arch/arm/mach-omap2/sdrc.c +41 -22

101 lines not on this page · raw message

arch/arm/mach-omap2/sram34xx.S +107 -30

193 lines not on this page · raw message

arch/arm/plat-omap/include/mach/io.h +2 -1
index 73f483d..21fb0ef 100644
@@ -228,7 +228,8 @@ extern void omap1_map_common_io(void);
 extern void omap1_init_common_hw(void);
 
 extern void omap2_map_common_io(void);
-extern void omap2_init_common_hw(struct omap_sdrc_params *sp);
+extern void omap2_init_common_hw(struct omap_sdrc_params *sdrc_cs0,
+				 struct omap_sdrc_params *sdrc_cs1);
 
 #define __arch_ioremap(p,s,t)	omap_ioremap(p,s,t)
 #define __arch_iounmap(v)	omap_iounmap(v)
arch/arm/plat-omap/include/mach/sdrc.h +9 -2
index adc7352..0be18e4 100644
@@ -30,6 +30,10 @@
 #define SDRC_ACTIM_CTRL_A_0	0x09c
 #define SDRC_ACTIM_CTRL_B_0	0x0a0
 #define SDRC_RFR_CTRL_0		0x0a4
+#define SDRC_MR_1		0x0B4
+#define SDRC_ACTIM_CTRL_A_1	0x0C4
+#define SDRC_ACTIM_CTRL_B_1	0x0C8
+#define SDRC_RFR_CTRL_1		0x0D4
 
 /*
  * These values represent the number of memory clock cycles between
@@ -102,8 +106,11 @@ struct omap_sdrc_params {
 	u32 mr;
 };
 
-void __init omap2_sdrc_init(struct omap_sdrc_params *sp);
-struct omap_sdrc_params *omap2_sdrc_get_params(unsigned long r);
+void __init omap2_sdrc_init(struct omap_sdrc_params *sdrc_cs0,
+			    struct omap_sdrc_params *sdrc_cs1);
+int omap2_sdrc_get_params(unsigned long r,
+			  struct omap_sdrc_params **sdrc_cs0,
+			  struct omap_sdrc_params **sdrc_cs1);
 
 #ifdef CONFIG_ARCH_OMAP2
 
arch/arm/plat-omap/include/mach/sram.h +12 -11
index 4d53cc5..8974e3f 100644
@@ -21,11 +21,12 @@ extern void omap2_sram_reprogram_sdrc(u32 perf_level, u32 dll_val,
 				      u32 mem_type);
 extern u32 omap2_set_prcm(u32 dpll_ctrl_val, u32 sdrc_rfr_val, int bypass);
 
-extern u32 omap3_configure_core_dpll(u32 sdrc_rfr_ctrl,
-				     u32 sdrc_actim_ctrla,
-				     u32 sdrc_actim_ctrlb, u32 m2,
-				     u32 unlock_dll, u32 f, u32 sdrc_mr,
-				     u32 inc);
+extern u32 omap3_configure_core_dpll(
+			u32 m2, u32 unlock_dll, u32 f, u32 inc,
+			u32 sdrc_rfr_ctrl_0, u32 sdrc_actim_ctrl_a_0,
+			u32 sdrc_actim_ctrl_b_0, u32 sdrc_mr_0,
+			u32 sdrc_rfr_ctrl_1, u32 sdrc_actim_ctrl_a_1,
+			u32 sdrc_actim_ctrl_b_1, u32 sdrc_mr_1);
 
 /* Do not use these */
 extern void omap1_sram_reprogram_clock(u32 ckctl, u32 dpllctl);
@@ -59,12 +60,12 @@ extern void omap243x_sram_reprogram_sdrc(u32 perf_level, u32 dll_val,
 						u32 mem_type);
 extern unsigned long omap243x_sram_reprogram_sdrc_sz;
 
-
-extern u32 omap3_sram_configure_core_dpll(u32 sdrc_rfr_ctrl,
-					  u32 sdrc_actim_ctrla,
-					  u32 sdrc_actim_ctrlb, u32 m2,
-					  u32 unlock_dll, u32 f, u32 sdrc_mr,
-					  u32 inc);
+extern u32 omap3_sram_configure_core_dpll(
+			u32 m2, u32 unlock_dll, u32 f, u32 inc,
+			u32 sdrc_rfr_ctrl_0, u32 sdrc_actim_ctrl_a_0,
+			u32 sdrc_actim_ctrl_b_0, u32 sdrc_mr_0,
+			u32 sdrc_rfr_ctrl_1, u32 sdrc_actim_ctrl_a_1,
+			u32 sdrc_actim_ctrl_b_1, u32 sdrc_mr_1);
 extern unsigned long omap3_sram_configure_core_dpll_sz;
 
 #endif
arch/arm/plat-omap/sram.c +18 -12
index 4ea7380..4e781c9 100644
@@ -373,20 +373,26 @@ static inline int omap243x_sram_init(void)
 
 #ifdef CONFIG_ARCH_OMAP3
 
-static u32 (*_omap3_sram_configure_core_dpll)(u32 sdrc_rfr_ctrl,
-					      u32 sdrc_actim_ctrla,
-					      u32 sdrc_actim_ctrlb,
-					      u32 m2, u32 unlock_dll,
-					      u32 f, u32 sdrc_mr, u32 inc);
-u32 omap3_configure_core_dpll(u32 sdrc_rfr_ctrl, u32 sdrc_actim_ctrla,
-			      u32 sdrc_actim_ctrlb, u32 m2, u32 unlock_dll,
-			      u32 f, u32 sdrc_mr, u32 inc)
+static u32 (*_omap3_sram_configure_core_dpll)(
+			u32 m2, u32 unlock_dll, u32 f, u32 inc,
+			u32 sdrc_rfr_ctrl_0, u32 sdrc_actim_ctrl_a_0,
+			u32 sdrc_actim_ctrl_b_0, u32 sdrc_mr_0,
+			u32 sdrc_rfr_ctrl_1, u32 sdrc_actim_ctrl_a_1,
+			u32 sdrc_actim_ctrl_b_1, u32 sdrc_mr_1);
+
+u32 omap3_configure_core_dpll(u32 m2, u32 unlock_dll, u32 f, u32 inc,
+			u32 sdrc_rfr_ctrl_0, u32 sdrc_actim_ctrl_a_0,
+			u32 sdrc_actim_ctrl_b_0, u32 sdrc_mr_0,
+			u32 sdrc_rfr_ctrl_1, u32 sdrc_actim_ctrl_a_1,
+			u32 sdrc_actim_ctrl_b_1, u32 sdrc_mr_1)
 {
 	BUG_ON(!_omap3_sram_configure_core_dpll);
-	return _omap3_sram_configure_core_dpll(sdrc_rfr_ctrl,
-					       sdrc_actim_ctrla,
-					       sdrc_actim_ctrlb, m2,
-					       unlock_dll, f, sdrc_mr, inc);
+	return _omap3_sram_configure_core_dpll(
+			m2, unlock_dll, f, inc,
+			sdrc_rfr_ctrl_0, sdrc_actim_ctrl_a_0,
+			sdrc_actim_ctrl_b_0, sdrc_mr_0,
+			sdrc_rfr_ctrl_1, sdrc_actim_ctrl_a_1,
+			sdrc_actim_ctrl_b_1, sdrc_mr_1);
 }
 
 /* REVISIT: Should this be same as omap34xx_sram_init() after off-idle? */
author maintainer
#2 lore raw

PATCH 2/8 OMAP3: Setup MUX settings for SDRC CKE signals

In reply to Paul Walmsley

From: Jean Pihet <[email protected]>

This patches ensures the MUX settings are correct for the SDRC CKE signals to SDRAM. This allows the self-refresh to work when 2 chip-selects are in use.

A warning is thrown away in case the initial muxing is incorrect, in order to track faulty or old-dated bootloaders.
Note: The CONFIG_OMAP_MUX and CONFIG_OMAP_MUX_WARNINGS options must be enabled for the mux code to have effect.

---
 arch/arm/mach-omap2/board-omap3beagle.c  |    4 ++++
 arch/arm/mach-omap2/board-omap3pandora.c |    5 +++++
 arch/arm/mach-omap2/board-overo.c        |    5 +++++
 arch/arm/mach-omap2/board-rx51.c         |    4 ++++
 arch/arm/mach-omap2/mux.c                |    6 ++++++
 arch/arm/plat-omap/include/mach/mux.h    |    4 ++++
 6 files changed, 28 insertions(+), 0 deletions(-)
arch/arm/mach-omap2/board-omap3beagle.c +4 -0
index 4abefd9..e00ba12 100644
@@ -409,6 +409,10 @@ static void __init omap3_beagle_init(void)
 
 	usb_musb_init();
 	omap3beagle_flash_init();
+
+	/* Ensure SDRC pins are mux'd for self-refresh */
+	omap_cfg_reg(H16_34XX_SDRC_CKE0);
+	omap_cfg_reg(H17_34XX_SDRC_CKE1);
 }
 
 static void __init omap3_beagle_map_io(void)
arch/arm/mach-omap2/board-omap3pandora.c +5 -0
index 9b991ce..864ee3d 100644
@@ -40,6 +40,7 @@
 #include <mach/mcspi.h>
 #include <mach/usb.h>
 #include <mach/keypad.h>
+#include <mach/mux.h>
 
 #include "sdram-micron-mt46h32m32lf-6.h"
 #include "mmc-twl4030.h"
@@ -398,6 +399,10 @@ static void __init omap3pandora_init(void)
 	omap3pandora_ads7846_init();
 	pandora_keys_gpio_init();
 	usb_musb_init();
+
+	/* Ensure SDRC pins are mux'd for self-refresh */
+	omap_cfg_reg(H16_34XX_SDRC_CKE0);
+	omap_cfg_reg(H17_34XX_SDRC_CKE1);
 }
 
 static void __init omap3pandora_map_io(void)
arch/arm/mach-omap2/board-overo.c +5 -0
index 44bc1c5..6b171b3 100644
@@ -44,6 +44,7 @@
 #include <mach/gpmc.h>
 #include <mach/hardware.h>
 #include <mach/nand.h>
+#include <mach/mux.h>
 #include <mach/usb.h>
 
 #include "sdram-micron-mt46h32m32lf-6.h"
@@ -396,6 +397,10 @@ static void __init overo_init(void)
 	overo_ads7846_init();
 	overo_init_smsc911x();
 
+	/* Ensure SDRC pins are mux'd for self-refresh */
+	omap_cfg_reg(H16_34XX_SDRC_CKE0);
+	omap_cfg_reg(H17_34XX_SDRC_CKE1);
+
 	if ((gpio_request(OVERO_GPIO_W2W_NRESET,
 			  "OVERO_GPIO_W2W_NRESET") == 0) &&
 	    (gpio_direction_output(OVERO_GPIO_W2W_NRESET, 1) == 0)) {
arch/arm/mach-omap2/board-rx51.c +4 -0
index 591ae8a..1c9e07f 100644
@@ -75,6 +75,10 @@ static void __init rx51_init(void)
 	omap_serial_init();
 	usb_musb_init();
 	rx51_peripherals_init();
+
+	/* Ensure SDRC pins are mux'd for self-refresh */
+	omap_cfg_reg(H16_34XX_SDRC_CKE0);
+	omap_cfg_reg(H17_34XX_SDRC_CKE1);
 }
 
 static void __init rx51_map_io(void)
arch/arm/mach-omap2/mux.c +6 -0
index 026c4fc..43d6b92 100644
@@ -486,6 +486,12 @@ MUX_CFG_34XX("H19_34XX_GPIO164_OUT", 0x19c,
 		OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_OUTPUT)
 MUX_CFG_34XX("J25_34XX_GPIO170", 0x1c6,
 		OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_INPUT)
+
+/* OMAP3 SDRC CKE signals to SDR/DDR ram chips */
+MUX_CFG_34XX("H16_34XX_SDRC_CKE0", 0x262,
+		OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_OUTPUT)
+MUX_CFG_34XX("H17_34XX_SDRC_CKE1", 0x264,
+		OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_OUTPUT)
 };
 
 #define OMAP34XX_PINS_SZ	ARRAY_SIZE(omap34xx_pins)
arch/arm/plat-omap/include/mach/mux.h +4 -0
index 85a6217..80281c4 100644
@@ -853,6 +853,10 @@ enum omap34xx_index {
 	AE5_34XX_GPIO143,
 	H19_34XX_GPIO164_OUT,
 	J25_34XX_GPIO170,
+
+	/* OMAP3 SDRC CKE signals to SDR/DDR ram chips */
+	H16_34XX_SDRC_CKE0,
+	H17_34XX_SDRC_CKE1,
 };
 
 struct omap_mux_cfg {
author maintainer
#3 lore raw

PATCH 3/8 OMAP2/3 SDRC: don't set SDRC_POWER.PWDENA on boot

In reply to Paul Walmsley

Stop setting SDRC_POWER.PWDENA on boot. There is a nasty erratum (34xx erratum 1.150) that can cause memory corruption if PWDENA is enabled.

Based originally on a patch from Samu P. Onkalo <[email protected]>.

Tested on BeagleBoard rev C2.

---
 arch/arm/mach-omap2/sdrc.c     |    5 ++++-
 arch/arm/mach-omap2/sram34xx.S |    2 --
 2 files changed, 4 insertions(+), 3 deletions(-)
arch/arm/mach-omap2/sdrc.c +4 -1
index 2e9e38d..9e3bd4f 100644
@@ -125,8 +125,11 @@ void __init omap2_sdrc_init(struct omap_sdrc_params *sdrc_cs0,
 	sdrc_init_params_cs1 = sdrc_cs1;
 
 	/* XXX Enable SRFRONIDLEREQ here also? */
+	/*
+	 * PWDENA should not be set due to 34xx erratum 1.150 - PWDENA
+	 * can cause random memory corruption
+	 */
 	l = (1 << SDRC_POWER_EXTCLKDIS_SHIFT) |
-		(1 << SDRC_POWER_PWDENA_SHIFT) |
 		(1 << SDRC_POWER_PAGEPOLICY_SHIFT);
 	sdrc_write_reg(l, SDRC_POWER);
 }
arch/arm/mach-omap2/sram34xx.S +0 -2
index 3aef744..9c2d046 100644
@@ -58,7 +58,6 @@
 
 /* SDRC_POWER bit settings */
 #define SRFRONIDLEREQ_MASK		0x40
-#define PWDENA_MASK			0x4
 
 /* CM_IDLEST1_CORE bit settings */
 #define ST_SDRC_MASK			0x2
@@ -160,7 +159,6 @@ sdram_in_selfrefresh:
 	ldr	r12, [r11]		@ read the contents of SDRC_POWER
 	mov	r9, r12			@ keep a copy of SDRC_POWER bits
 	orr 	r12, r12, #SRFRONIDLEREQ_MASK	@ enable self refresh on idle
-	bic 	r12, r12, #PWDENA_MASK	@ clear PWDENA
 	str 	r12, [r11]		@ write back to SDRC_POWER register
 	ldr	r12, [r11]		@ posted-write barrier for SDRC
 idle_sdrc:
author maintainer
#4 lore raw

PATCH 4/8 OMAP3 SDRC: Fix freeze when scaling CORE dpll to < 83Mhz

In reply to Paul Walmsley

From: Rajendra Nayak <[email protected]>

This patch fixes a bug in the CORE dpll scaling sequence which was errouneously clearing some bits in the SDRC DLLA CTRL register and hence causing a freeze. The issue was observed only on platforms which scale CORE dpll to < 83Mhz and hence program the DLL in fixed delay mode.

Issue reported by Limei Wang <[email protected]>, with debugging assistance from Richard Woodruff <[email protected]> and Girish Ghongdemath <[email protected]>.

Cc Limei Wang <[email protected]>
Cc Richard Woodruff <[email protected]>
Cc Girish Ghongdemath <[email protected]>
[[email protected]: updated patch description to include collaboration credits]
---
 arch/arm/mach-omap2/sram34xx.S |    2 +-
 1 files changed, 1 insertions(+), 1 deletions(-)
arch/arm/mach-omap2/sram34xx.S +1 -1
index 9c2d046..e6b1125 100644
@@ -143,7 +143,7 @@ return_to_sdram:
 unlock_dll:
 	ldr	r11, omap3_sdrc_dlla_ctrl
 	ldr	r12, [r11]
-	and	r12, r12, #FIXEDDELAY_MASK
+	bic	r12, r12, #FIXEDDELAY_MASK
 	orr	r12, r12, #FIXEDDELAY_DEFAULT
 	orr	r12, r12, #DLLIDLE_MASK
 	str	r12, [r11]		@ (no OCP barrier needed)
author maintainer
#5 lore raw

PATCH 5/8 OMAP3 SDRC: Move the clk stabilization delay to the right place

In reply to Paul Walmsley

From: Rajendra Nayak <[email protected]>

The clock stabilization delay post a M2 divider change is needed even before a SDRC interface clock re-enable and not only before jumping back to SDRAM.

---
 arch/arm/mach-omap2/sram34xx.S |    4 ++--
 1 files changed, 2 insertions(+), 2 deletions(-)
arch/arm/mach-omap2/sram34xx.S +2 -2
index e6b1125..82aa4a3 100644
@@ -127,6 +127,8 @@ skip_cs1_params:
 	blne	lock_dll
 	bl	sdram_in_selfrefresh	@ put SDRAM in self refresh, idle SDRC
 	bl 	configure_core_dpll	@ change the DPLL3 M2 divider
+	mov	r12, r2
+	bl	wait_clk_stable		@ wait for SDRC to stabilize
 	bl	enable_sdrc		@ take SDRC out of idle
 	cmp	r1, #SDRC_UNLOCK_DLL	@ wait for DLL status to change
 	bleq	wait_dll_unlock
@@ -134,8 +136,6 @@ skip_cs1_params:
 	cmp	r3, #1			@ if increasing SDRC clk rate,
 	beq	return_to_sdram		@ return to SDRAM code, otherwise,
 	bl	configure_sdrc		@ reprogram SDRC regs now
-	mov	r12, r2
-	bl	wait_clk_stable		@ wait for SDRC to stabilize
 return_to_sdram:
 	isb				@ prevent speculative exec past here
 	mov 	r0, #0 			@ return value
author maintainer
#6 lore raw

PATCH 6/8 OMAP2/3 clock: split, rename omap2_wait_clock_ready()

In reply to Paul Walmsley

Some OMAP2/3 hardware modules have CM_IDLEST attributes that are not handled by the current omap2_wait_clock_ready() code. In preparation for patches that fix the unusual devices, rename the function omap2_wait_clock_ready() to omap2_wait_module_ready() and split it into three parts:

1. A clkops-specific companion clock return function (by default, omap2_clk_dflt_find_companion())

2. A clkops-specific CM_IDLEST register address and bit shift return function (by default, omap2_clk_dflt_find_idlest())

3. Code to wait for the CM to indicate that the module is ready (omap2_cm_wait_idlest())

Clocks can now specify their own custom find_companion() and find_idlest() functions; used in subsequent patches.

---
 arch/arm/mach-omap2/clock.c             |  156 ++++++++++++++++---------------
 arch/arm/mach-omap2/clock.h             |    6 +
 arch/arm/mach-omap2/prcm.c              |   43 +++++++++
 arch/arm/plat-omap/include/mach/clock.h |    2 
 arch/arm/plat-omap/include/mach/prcm.h  |    1 
 5 files changed, 131 insertions(+), 77 deletions(-)
arch/arm/mach-omap2/clock.c +79 -77
index b0665f1..456e2ad 100644
@@ -27,6 +27,7 @@
 #include <mach/clock.h>
 #include <mach/clockdomain.h>
 #include <mach/cpu.h>
+#include <mach/prcm.h>
 #include <asm/div64.h>
 
 #include <mach/sdrc.h>
@@ -38,8 +39,6 @@
 #include "cm-regbits-24xx.h"
 #include "cm-regbits-34xx.h"
 
-#define MAX_CLOCK_ENABLE_WAIT		100000
-
 /* DPLL rate rounding: minimum DPLL multiplier, divider values */
 #define DPLL_MIN_MULTIPLIER		1
 #define DPLL_MIN_DIVIDER		1
@@ -274,83 +273,97 @@ unsigned long omap2_fixed_divisor_recalc(struct clk *clk)
 }
 
 /**
- * omap2_wait_clock_ready - wait for clock to enable
- * @reg: physical address of clock IDLEST register
- * @mask: value to mask against to determine if the clock is active
- * @name: name of the clock (for printk)
+ * omap2_clk_dflt_find_companion - find companion clock to @clk
+ * @clk: struct clk * to find the companion clock of
+ * @other_reg: void __iomem ** to return the companion clock CM_*CLKEN va in
+ * @other_bit: u8 ** to return the companion clock bit shift in
+ *
+ * Note: We don't need special code here for INVERT_ENABLE for the
+ * time being since INVERT_ENABLE only applies to clocks enabled by
+ * CM_CLKEN_PLL
  *
- * Returns 1 if the clock enabled in time, or 0 if it failed to enable
- * in roughly MAX_CLOCK_ENABLE_WAIT microseconds.
+ * Convert CM_ICLKEN* <-> CM_FCLKEN*.  This conversion assumes it's
+ * just a matter of XORing the bits.
+ *
+ * Some clocks don't have companion clocks.  For example, modules with
+ * only an interface clock (such as MAILBOXES) don't have a companion
+ * clock.  Right now, this code relies on the hardware exporting a bit
+ * in the correct companion register that indicates that the
+ * nonexistent 'companion clock' is active.  Future patches will
+ * associate this type of code with per-module data structures to
+ * avoid this issue, and remove the casts.  No return value.
  */
-int omap2_wait_clock_ready(void __iomem *reg, u32 mask, const char *name)
+void omap2_clk_dflt_find_companion(struct clk *clk, void __iomem **other_reg,
+				   u8 *other_bit)
 {
-	int i = 0;
-	int ena = 0;
+	u32 r;
 
 	/*
-	 * 24xx uses 0 to indicate not ready, and 1 to indicate ready.
-	 * 34xx reverses this, just to keep us on our toes
+	 * Convert CM_ICLKEN* <-> CM_FCLKEN*.  This conversion assumes
+	 * it's just a matter of XORing the bits.
 	 */
-	if (cpu_mask & (RATE_IN_242X | RATE_IN_243X))
-		ena = mask;
-	else if (cpu_mask & RATE_IN_343X)
-		ena = 0;
-
-	/* Wait for lock */
-	while (((__raw_readl(reg) & mask) != ena) &&
-	       (i++ < MAX_CLOCK_ENABLE_WAIT)) {
-		udelay(1);
-	}
-
-	if (i <= MAX_CLOCK_ENABLE_WAIT)
-		pr_debug("Clock %s stable after %d loops\n", name, i);
-	else
-		printk(KERN_ERR "Clock %s didn't enable in %d tries\n",
-		       name, MAX_CLOCK_ENABLE_WAIT);
-
-
-	return (i < MAX_CLOCK_ENABLE_WAIT) ? 1 : 0;
-};
+	r = ((__force u32)clk->enable_reg ^ (CM_FCLKEN ^ CM_ICLKEN));
 
+	*other_reg = (__force void __iomem *)r;
+	*other_bit = clk->enable_bit;
+}
 
-/*
- * Note: We don't need special code here for INVERT_ENABLE
- * for the time being since INVERT_ENABLE only applies to clocks enabled by
- * CM_CLKEN_PLL
+/**
+ * omap2_clk_dflt_find_idlest - find CM_IDLEST reg va, bit shift for @clk
+ * @clk: struct clk * to find IDLEST info for
+ * @idlest_reg: void __iomem ** to return the CM_IDLEST va in
+ * @idlest_bit: u8 ** to return the CM_IDLEST bit shift in
+ *
+ * Return the CM_IDLEST register address and bit shift corresponding
+ * to the module that "owns" this clock.  This default code assumes
+ * that the CM_IDLEST bit shift is the CM_*CLKEN bit shift, and that
+ * the IDLEST register address ID corresponds to the CM_*CLKEN
+ * register address ID (e.g., that CM_FCLKEN2 corresponds to
+ * CM_IDLEST2).  This is not true for all modules.  No return value.
  */
-static void omap2_clk_wait_ready(struct clk *clk)
+void omap2_clk_dflt_find_idlest(struct clk *clk, void __iomem **idlest_reg,
+				u8 *idlest_bit)
 {
-	void __iomem *reg, *other_reg, *st_reg;
-	u32 bit;
+	u32 r;
 
-	/*
-	 * REVISIT: This code is pretty ugly.  It would be nice to generalize
-	 * it and pull it into struct clk itself somehow.
-	 */
-	reg = clk->enable_reg;
+	r = (((__force u32)clk->enable_reg & ~0xf0) | 0x20);
+	*idlest_reg = (__force void __iomem *)r;
+	*idlest_bit = clk->enable_bit;
+}
 
-	/*
-	 * Convert CM_ICLKEN* <-> CM_FCLKEN*.  This conversion assumes
-	 * it's just a matter of XORing the bits.
-	 */
-	other_reg = (void __iomem *)((u32)reg ^ (CM_FCLKEN ^ CM_ICLKEN));
+/**
+ * omap2_module_wait_ready - wait for an OMAP module to leave IDLE
+ * @clk: struct clk * belonging to the module
+ *
+ * If the necessary clocks for the OMAP hardware IP block that
+ * corresponds to clock @clk are enabled, then wait for the module to
+ * indicate readiness (i.e., to leave IDLE).  This code does not
+ * belong in the clock code and will be moved in the medium term to
+ * module-dependent code.  No return value.
+ */
+static void omap2_module_wait_ready(struct clk *clk)
+{
+	void __iomem *companion_reg, *idlest_reg;
+	u8 other_bit, idlest_bit;
+
+	/* Not all modules have multiple clocks that their IDLEST depends on */
+	if (clk->ops->find_companion) {
+		clk->ops->find_companion(clk, &companion_reg, &other_bit);
+		if (!(__raw_readl(companion_reg) & (1 << other_bit)))
+			return;
+	}
 
-	/* Check if both functional and interface clocks
-	 * are running. */
-	bit = 1 << clk->enable_bit;
-	if (!(__raw_readl(other_reg) & bit))
-		return;
-	st_reg = (void __iomem *)(((u32)other_reg & ~0xf0) | 0x20); /* CM_IDLEST* */
+	clk->ops->find_idlest(clk, &idlest_reg, &idlest_bit);
 
-	omap2_wait_clock_ready(st_reg, bit, clk->name);
+	omap2_cm_wait_idlest(idlest_reg, (1 << idlest_bit), clk->name);
 }
 
-static int omap2_dflt_clk_enable(struct clk *clk)
+int omap2_dflt_clk_enable(struct clk *clk)
 {
 	u32 v;
 
 	if (unlikely(clk->enable_reg == NULL)) {
-		printk(KERN_ERR "clock.c: Enable for %s without enable code\n",
+		pr_err("clock.c: Enable for %s without enable code\n",
 		       clk->name);
 		return 0; /* REVISIT: -EINVAL */
 	}
@@ -363,26 +376,13 @@ static int omap2_dflt_clk_enable(struct clk *clk)
 	__raw_writel(v, clk->enable_reg);
 	v = __raw_readl(clk->enable_reg); /* OCP barrier */
 
-	return 0;
-}
+	if (clk->ops->find_idlest)
+		omap2_module_wait_ready(clk);
 
-static int omap2_dflt_clk_enable_wait(struct clk *clk)
-{
-	int ret;
-
-	if (!clk->enable_reg) {
-		printk(KERN_ERR "clock.c: Enable for %s without enable code\n",
-		       clk->name);
-		return 0; /* REVISIT: -EINVAL */
-	}
-
-	ret = omap2_dflt_clk_enable(clk);
-	if (ret == 0)
-		omap2_clk_wait_ready(clk);
-	return ret;
+	return 0;
 }
 
-static void omap2_dflt_clk_disable(struct clk *clk)
+void omap2_dflt_clk_disable(struct clk *clk)
 {
 	u32 v;
 
@@ -406,8 +406,10 @@ static void omap2_dflt_clk_disable(struct clk *clk)
 }
 
 const struct clkops clkops_omap2_dflt_wait = {
-	.enable		= omap2_dflt_clk_enable_wait,
+	.enable		= omap2_dflt_clk_enable,
 	.disable	= omap2_dflt_clk_disable,
+	.find_companion	= omap2_clk_dflt_find_companion,
+	.find_idlest	= omap2_clk_dflt_find_idlest,
 };
 
 const struct clkops clkops_omap2_dflt = {
arch/arm/mach-omap2/clock.h +6 -0
index 2679ddf..9ae7540 100644
@@ -65,6 +65,12 @@ int omap2_clksel_set_rate(struct clk *clk, unsigned long rate);
 u32 omap2_get_dpll_rate(struct clk *clk);
 int omap2_wait_clock_ready(void __iomem *reg, u32 cval, const char *name);
 void omap2_clk_prepare_for_reboot(void);
+int omap2_dflt_clk_enable(struct clk *clk);
+void omap2_dflt_clk_disable(struct clk *clk);
+void omap2_clk_dflt_find_companion(struct clk *clk, void __iomem **other_reg,
+				   u8 *other_bit);
+void omap2_clk_dflt_find_idlest(struct clk *clk, void __iomem **idlest_reg,
+				u8 *idlest_bit);
 
 extern const struct clkops clkops_omap2_dflt_wait;
 extern const struct clkops clkops_omap2_dflt;
arch/arm/mach-omap2/prcm.c +43 -0

61 lines not on this page · raw message

arch/arm/plat-omap/include/mach/clock.h +2 -0
index f9f65e1..4b8b0d6 100644
@@ -20,6 +20,8 @@ struct clockdomain;
 struct clkops {
 	int			(*enable)(struct clk *);
 	void			(*disable)(struct clk *);
+	void			(*find_idlest)(struct clk *, void __iomem **, u8 *);
+	void			(*find_companion)(struct clk *, void __iomem **, u8 *);
 };
 
 #if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3) || \
arch/arm/plat-omap/include/mach/prcm.h +1 -0
index 24ac3c7..cda2a70 100644
@@ -25,6 +25,7 @@
 
 u32 omap_prcm_get_reset_sources(void);
 void omap_prcm_arch_reset(char mode);
+int omap2_cm_wait_idlest(void __iomem *reg, u32 mask, const char *name);
 
 #endif
 
author maintainer
#7 lore raw

PATCH 7/8 OMAP2 clock: 2430 I2CHS uses non-standard CM_IDLEST register

In reply to Paul Walmsley

OMAP2430 I2CHS CM_IDLEST bits are in CM_IDLEST1_CORE, but the CM_*CLKEN bits are in CM_{I,F}CLKEN2_CORE [1]. Fix by implementing a custom clkops .find_idlest function to return the correct slave IDLEST register.

...

1. OMAP2430 Multimedia Device Package-on-Package (POP) Silicon Revision 2.1 (Rev. V) Technical Reference Manual, tables 4-99 and 4-105.

---
 arch/arm/mach-omap2/clock24xx.c |   37 +++++++++++++++++++++++++++++++++++--
 arch/arm/mach-omap2/clock24xx.h |    4 ++--
 2 files changed, 37 insertions(+), 4 deletions(-)
arch/arm/mach-omap2/clock24xx.c +35 -2
index 44de027..bc5d3ac 100644
@@ -30,6 +30,7 @@
 
 #include <mach/clock.h>
 #include <mach/sram.h>
+#include <mach/prcm.h>
 #include <asm/div64.h>
 #include <asm/clkdev.h>
 
@@ -43,6 +44,18 @@
 static const struct clkops clkops_oscck;
 static const struct clkops clkops_fixed;
 
+static void omap2430_clk_i2chs_find_idlest(struct clk *clk,
+					   void __iomem **idlest_reg,
+					   u8 *idlest_bit);
+
+/* 2430 I2CHS has non-standard IDLEST register */
+static const struct clkops clkops_omap2430_i2chs_wait = {
+	.enable		= omap2_dflt_clk_enable,
+	.disable	= omap2_dflt_clk_disable,
+	.find_idlest	= omap2430_clk_i2chs_find_idlest,
+	.find_companion = omap2_clk_dflt_find_companion,
+};
+
 #include "clock24xx.h"
 
 struct omap_clk {
@@ -240,6 +253,26 @@ static void __iomem *prcm_clksrc_ctrl;
  *-------------------------------------------------------------------------*/
 
 /**
+ * omap2430_clk_i2chs_find_idlest - return CM_IDLEST info for 2430 I2CHS
+ * @clk: struct clk * being enabled
+ * @idlest_reg: void __iomem ** to store CM_IDLEST reg address into
+ * @idlest_bit: pointer to a u8 to store the CM_IDLEST bit shift into
+ *
+ * OMAP2430 I2CHS CM_IDLEST bits are in CM_IDLEST1_CORE, but the
+ * CM_*CLKEN bits are in CM_{I,F}CLKEN2_CORE.  This custom function
+ * passes back the correct CM_IDLEST register address for I2CHS
+ * modules.  No return value.
+ */
+static void omap2430_clk_i2chs_find_idlest(struct clk *clk,
+					   void __iomem **idlest_reg,
+					   u8 *idlest_bit)
+{
+	*idlest_reg = OMAP_CM_REGADDR(CORE_MOD, CM_IDLEST);
+	*idlest_bit = clk->enable_bit;
+}
+
+
+/**
  * omap2xxx_clk_get_core_rate - return the CORE_CLK rate
  * @clk: pointer to the combined dpll_ck + core_ck (currently "dpll_ck")
  *
@@ -325,8 +358,8 @@ static int omap2_clk_fixed_enable(struct clk *clk)
 	else if (clk == &apll54_ck)
 		cval = OMAP24XX_ST_54M_APLL;
 
-	omap2_wait_clock_ready(OMAP_CM_REGADDR(PLL_MOD, CM_IDLEST), cval,
-			    clk->name);
+	omap2_cm_wait_idlest(OMAP_CM_REGADDR(PLL_MOD, CM_IDLEST), cval,
+			     clk->name);
 
 	/*
 	 * REVISIT: Should we return an error code if omap2_wait_clock_ready()
arch/arm/mach-omap2/clock24xx.h +2 -2
index 458f00c..d19cf7a 100644
@@ -2337,7 +2337,7 @@ static struct clk i2c2_fck = {
 
 static struct clk i2chs2_fck = {
 	.name		= "i2c_fck",
-	.ops		= &clkops_omap2_dflt_wait,
+	.ops		= &clkops_omap2430_i2chs_wait,
 	.id		= 2,
 	.parent		= &func_96m_ck,
 	.clkdm_name	= "core_l4_clkdm",
@@ -2370,7 +2370,7 @@ static struct clk i2c1_fck = {
 
 static struct clk i2chs1_fck = {
 	.name		= "i2c_fck",
-	.ops		= &clkops_omap2_dflt_wait,
+	.ops		= &clkops_omap2430_i2chs_wait,
 	.id		= 1,
 	.parent		= &func_96m_ck,
 	.clkdm_name	= "core_l4_clkdm",
author maintainer
#8 lore raw

PATCH 8/8 OMAP3 clock: correct module IDLEST bits: SSI; DSS; USBHOST; HSOTGUSB

In reply to Paul Walmsley

Fix two bugs in the OMAP3 clock tree pertaining to the SSI, DSS, USBHOST, and HSOTGUSB devices. These devices are both interconnect initiators and targets. Without this patch, clk_enable()s on clocks for these modules can be very high latency (potentially up to ~200 milliseconds) and message such as the following are generated:

Clock usbhost_48m_fck didn't enable in 100000 tries

Two bugs are fixed by this patch. First, OMAP hardware only supports target CM_IDLEST register bits on ES2+ chips and beyond. ES1 chips should not wait for these clocks to enable. So, split the appropriate clocks into ES1 and ES2+ variants, so that kernels running on ES1 devices won't try to wait.

Second, the current heuristic in omap2_clk_dflt_find_idlest() will fail for these clocks. It assumes that the CM_IDLEST bit to wait upon is the same as the CM_*CLKEN bit, which is false[1]. Fix by implementing custom clkops .find_idlest function pointers for the appropriate clocks that return the correct slave IDLEST bit shift.

This was originally fixed in the linux-omap kernel during 2.6.29 in a slightly different manner[2][3].

In the medium-term future, all of the module IDLEST code will eventually be moved to the omap_hwmod code.

Problem reported by Jarkko Nikula <[email protected]>:

    http://marc.info/?l=linux-omap&m=124306184903679&w=2

...

1. See for example 34xx TRM Revision P Table 4-213 and 4-217 (for the DSS case).

2. http://www.spinics.net/lists/linux-omap/msg05512.html et seq.

3. http://lkml.indiana.edu/hypermail/linux/kernel/0901.3/01498.html

---
 arch/arm/mach-omap2/clock34xx.c |  118 +++++++++++++++++++++++++++++++++++++--
 arch/arm/mach-omap2/clock34xx.h |   85 ++++++++++++++++++++++++----
 2 files changed, 185 insertions(+), 18 deletions(-)
arch/arm/mach-omap2/clock34xx.c +111 -7
index 1c6480d..cd7819c 100644
@@ -2,7 +2,7 @@
  * OMAP3-specific clock framework functions
  *
  * Copyright (C) 2007-2008 Texas Instruments, Inc.
- * Copyright (C) 2007-2008 Nokia Corporation
+ * Copyright (C) 2007-2009 Nokia Corporation
  *
  * Written by Paul Walmsley
  * Testing and integration fixes by Jouni Högander
@@ -41,6 +41,37 @@
 
 static const struct clkops clkops_noncore_dpll_ops;
 
+static void omap3430es2_clk_ssi_find_idlest(struct clk *clk,
+					    void __iomem **idlest_reg,
+					    u8 *idlest_bit);
+static void omap3430es2_clk_hsotgusb_find_idlest(struct clk *clk,
+					    void __iomem **idlest_reg,
+					    u8 *idlest_bit);
+static void omap3430es2_clk_dss_usbhost_find_idlest(struct clk *clk,
+						    void __iomem **idlest_reg,
+						    u8 *idlest_bit);
+
+static const struct clkops clkops_omap3430es2_ssi_wait = {
+	.enable		= omap2_dflt_clk_enable,
+	.disable	= omap2_dflt_clk_disable,
+	.find_idlest	= omap3430es2_clk_ssi_find_idlest,
+	.find_companion = omap2_clk_dflt_find_companion,
+};
+
+static const struct clkops clkops_omap3430es2_hsotgusb_wait = {
+	.enable		= omap2_dflt_clk_enable,
+	.disable	= omap2_dflt_clk_disable,
+	.find_idlest	= omap3430es2_clk_hsotgusb_find_idlest,
+	.find_companion = omap2_clk_dflt_find_companion,
+};
+
+static const struct clkops clkops_omap3430es2_dss_usbhost_wait = {
+	.enable		= omap2_dflt_clk_enable,
+	.disable	= omap2_dflt_clk_disable,
+	.find_idlest	= omap3430es2_clk_dss_usbhost_find_idlest,
+	.find_companion = omap2_clk_dflt_find_companion,
+};
+
 #include "clock34xx.h"
 
 struct omap_clk {
@@ -157,10 +188,13 @@ static struct omap_clk omap34xx_clks[] = {
 	CLK(NULL,	"fshostusb_fck", &fshostusb_fck, CK_3430ES1),
 	CLK(NULL,	"core_12m_fck",	&core_12m_fck,	CK_343X),
 	CLK("omap_hdq.0", "fck",	&hdq_fck,	CK_343X),
-	CLK(NULL,	"ssi_ssr_fck",	&ssi_ssr_fck,	CK_343X),
-	CLK(NULL,	"ssi_sst_fck",	&ssi_sst_fck,	CK_343X),
+	CLK(NULL,	"ssi_ssr_fck",	&ssi_ssr_fck_3430es1,	CK_3430ES1),
+	CLK(NULL,	"ssi_ssr_fck",	&ssi_ssr_fck_3430es2,	CK_3430ES2),
+	CLK(NULL,	"ssi_sst_fck",	&ssi_sst_fck_3430es1,	CK_3430ES1),
+	CLK(NULL,	"ssi_sst_fck",	&ssi_sst_fck_3430es2,	CK_3430ES2),
 	CLK(NULL,	"core_l3_ick",	&core_l3_ick,	CK_343X),
-	CLK("musb_hdrc",	"ick",	&hsotgusb_ick,	CK_343X),
+	CLK("musb_hdrc",	"ick",	&hsotgusb_ick_3430es1,	CK_3430ES1),
+	CLK("musb_hdrc",	"ick",	&hsotgusb_ick_3430es2,	CK_3430ES2),
 	CLK(NULL,	"sdrc_ick",	&sdrc_ick,	CK_343X),
 	CLK(NULL,	"gpmc_fck",	&gpmc_fck,	CK_343X),
 	CLK(NULL,	"security_l3_ick", &security_l3_ick, CK_343X),
@@ -193,18 +227,21 @@ static struct omap_clk omap34xx_clks[] = {
 	CLK(NULL,	"mailboxes_ick", &mailboxes_ick, CK_343X),
 	CLK(NULL,	"omapctrl_ick",	&omapctrl_ick,	CK_343X),
 	CLK(NULL,	"ssi_l4_ick",	&ssi_l4_ick,	CK_343X),
-	CLK(NULL,	"ssi_ick",	&ssi_ick,	CK_343X),
+	CLK(NULL,	"ssi_ick",	&ssi_ick_3430es1,	CK_3430ES1),
+	CLK(NULL,	"ssi_ick",	&ssi_ick_3430es2,	CK_3430ES2),
 	CLK(NULL,	"usb_l4_ick",	&usb_l4_ick,	CK_3430ES1),
 	CLK(NULL,	"security_l4_ick2", &security_l4_ick2, CK_343X),
 	CLK(NULL,	"aes1_ick",	&aes1_ick,	CK_343X),
 	CLK("omap_rng",	"ick",		&rng_ick,	CK_343X),
 	CLK(NULL,	"sha11_ick",	&sha11_ick,	CK_343X),
 	CLK(NULL,	"des1_ick",	&des1_ick,	CK_343X),
-	CLK("omapfb",	"dss1_fck",	&dss1_alwon_fck, CK_343X),
+	CLK("omapfb",	"dss1_fck",	&dss1_alwon_fck_3430es1, CK_3430ES1),
+	CLK("omapfb",	"dss1_fck",	&dss1_alwon_fck_3430es2, CK_3430ES2),
 	CLK("omapfb",	"tv_fck",	&dss_tv_fck,	CK_343X),
 	CLK("omapfb",	"video_fck",	&dss_96m_fck,	CK_343X),
 	CLK("omapfb",	"dss2_fck",	&dss2_alwon_fck, CK_343X),
-	CLK("omapfb",	"ick",		&dss_ick,	CK_343X),
+	CLK("omapfb",	"ick",		&dss_ick_3430es1,	CK_3430ES1),
+	CLK("omapfb",	"ick",		&dss_ick_3430es2,	CK_3430ES2),
 	CLK(NULL,	"cam_mclk",	&cam_mclk,	CK_343X),
 	CLK(NULL,	"cam_ick",	&cam_ick,	CK_343X),
 	CLK(NULL,	"csi2_96m_fck",	&csi2_96m_fck,	CK_343X),
@@ -301,6 +338,73 @@ static struct omap_clk omap34xx_clks[] = {
 #define SDRC_MPURATE_LOOPS		96
 
 /**
+ * omap3430es2_clk_ssi_find_idlest - return CM_IDLEST info for SSI
+ * @clk: struct clk * being enabled
+ * @idlest_reg: void __iomem ** to store CM_IDLEST reg address into
+ * @idlest_bit: pointer to a u8 to store the CM_IDLEST bit shift into
+ *
+ * The OMAP3430ES2 SSI target CM_IDLEST bit is at a different shift
+ * from the CM_{I,F}CLKEN bit.  Pass back the correct info via
+ * @idlest_reg and @idlest_bit.  No return value.
+ */
+static void omap3430es2_clk_ssi_find_idlest(struct clk *clk,
+					    void __iomem **idlest_reg,
+					    u8 *idlest_bit)
+{
+	u32 r;
+
+	r = (((__force u32)clk->enable_reg & ~0xf0) | 0x20);
+	*idlest_reg = (__force void __iomem *)r;
+	*idlest_bit = OMAP3430ES2_ST_SSI_IDLE_SHIFT;
+}
+
+/**
+ * omap3430es2_clk_dss_usbhost_find_idlest - CM_IDLEST info for DSS, USBHOST
+ * @clk: struct clk * being enabled
+ * @idlest_reg: void __iomem ** to store CM_IDLEST reg address into
+ * @idlest_bit: pointer to a u8 to store the CM_IDLEST bit shift into
+ *
+ * Some OMAP modules on OMAP3 ES2+ chips have both initiator and
+ * target IDLEST bits.  For our purposes, we are concerned with the
+ * target IDLEST bits, which exist at a different bit position than
+ * the *CLKEN bit position for these modules (DSS and USBHOST) (The
+ * default find_idlest code assumes that they are at the same
+ * position.)  No return value.
+ */
+static void omap3430es2_clk_dss_usbhost_find_idlest(struct clk *clk,
+						    void __iomem **idlest_reg,
+						    u8 *idlest_bit)
+{
+	u32 r;
+
+	r = (((__force u32)clk->enable_reg & ~0xf0) | 0x20);
+	*idlest_reg = (__force void __iomem *)r;
+	/* USBHOST_IDLE has same shift */
+	*idlest_bit = OMAP3430ES2_ST_DSS_IDLE_SHIFT;
+}
+
+/**
+ * omap3430es2_clk_hsotgusb_find_idlest - return CM_IDLEST info for HSOTGUSB
+ * @clk: struct clk * being enabled
+ * @idlest_reg: void __iomem ** to store CM_IDLEST reg address into
+ * @idlest_bit: pointer to a u8 to store the CM_IDLEST bit shift into
+ *
+ * The OMAP3430ES2 HSOTGUSB target CM_IDLEST bit is at a different
+ * shift from the CM_{I,F}CLKEN bit.  Pass back the correct info via
+ * @idlest_reg and @idlest_bit.  No return value.
+ */
+static void omap3430es2_clk_hsotgusb_find_idlest(struct clk *clk,
+						 void __iomem **idlest_reg,
+						 u8 *idlest_bit)
+{
+	u32 r;
+
+	r = (((__force u32)clk->enable_reg & ~0xf0) | 0x20);
+	*idlest_reg = (__force void __iomem *)r;
+	*idlest_bit = OMAP3430ES2_ST_HSOTGUSB_IDLE_SHIFT;
+}
+
+/**
  * omap3_dpll_recalc - recalculate DPLL rate
  * @clk: DPLL struct clk
  *
arch/arm/mach-omap2/clock34xx.h +74 -11

160 lines not on this page · raw message

--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html