Skip to contentSkip to conversation

Adaptec 1405 and mvsas

DISCUSSION Marco Gruß 2 participants 3 messages Sep 4, 2009 – Sep 21, 2009

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

Hello,

I recently acquired an Adaptec 1405 SAS/SATA HBA.

While there is a closed-source driver by Adaptec, called adpinv, I'd of course like to get it to work with open drivers.

A lspci -v reveals that the controller is actually using a Marvell chip:

02:00.0 Serial Attached SCSI controller: Adaptec Device 0450 (rev 02)
Subsystem: Marvell Technology Group Ltd. Device 6440

02:00.0 0107: 9005:0450 (rev 02)

        Subsystem: 11ab:6440

(The output of lspci -vv is attached below)

So I simply added an entry for this PCI id to mvsas.c:

static struct pci_device_id __devinitdata mvs_pci_table[] = {
        { PCI_VDEVICE(MARVELL, 0x6320), chip_6320 },
        { PCI_VDEVICE(MARVELL, 0x6340), chip_6440 },
        {
                .vendor         = PCI_VENDOR_ID_MARVELL,
                .device         = 0x6440,
                .subvendor      = PCI_ANY_ID,
                .subdevice      = 0x6480,
                .class          = 0,
                .class_mask     = 0,
                .driver_data    = chip_6480,
        },
        { PCI_VDEVICE(MARVELL, 0x6440), chip_6440 },
        { PCI_VDEVICE(MARVELL, 0x6480), chip_6480 },

+ { PCI_VDEVICE(ADAPTEC2, 0x0450), chip_6440 },

{ } /* terminate list */
};

...with limited success:

Aug 29 17:22:54 athlon kernel: mvsas 0000:02:00.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
Aug 29 17:22:54 athlon kernel: mvsas 0000:02:00.0: setting latency timer to 64
Aug 29 17:22:56 athlon kernel: mvsas 0000:02:00.0: phy[2] Get Attached Address 0x2 , SAS Address 0x5005043011AB0000
Aug 29 17:22:56 athlon kernel: mvsas 0000:02:00.0: Rate = 9 , type = 1
Aug 29 17:22:56 athlon kernel: mvsas 0000:02:00.0: phy[3] Get Attached Address 0x3 , SAS Address 0x5005043011AB0000
Aug 29 17:22:56 athlon kernel: mvsas 0000:02:00.0: Rate = 8 , type = 1
Aug 29 17:22:56 athlon kernel: scsi4 : mvsas
Aug 29 17:22:56 athlon kernel: mvsas 0000:02:00.0: version 0.5.2
Aug 29 17:22:56 athlon kernel: mvsas 0000:02:00.0: 4 phys, addr 5005043011ab0000
Aug 29 17:22:56 athlon kernel: sas: phy-4:2 added to port-4:0, phy_mask:0x4 (               2)
Aug 29 17:22:56 athlon kernel: sas: phy-4:3 added to port-4:1, phy_mask:0x8 (               3)
Aug 29 17:22:56 athlon kernel: sas: DOING DISCOVERY on port 0, pid:6916
Aug 29 17:22:56 athlon kernel: sas: sas_ata_phy_reset: Unable to reset I T nexus?
Aug 29 17:22:56 athlon kernel: sas: sas_ata_phy_reset: Found ATA device.
Aug 29 17:22:56 athlon kernel: ata5.00: ATA-8: OCZ CORE_SSD, 02.10103, max UDMA/100
Aug 29 17:22:56 athlon kernel: ata5.00: 59047936 sectors, multi 0: LBA
Aug 29 17:22:56 athlon kernel: ata5.00: configured for UDMA/100
Aug 29 17:22:56 athlon kernel: scsi 4:0:0:0: Direct-Access     ATA      OCZ CORE_SSD     02.1 PQ: 0 ANSI: 5
Aug 29 17:22:56 athlon kernel: sd 4:0:0:0: Attached scsi generic sg3 type 0
Aug 29 17:22:56 athlon kernel: sas: DONE DISCOVERY on port 0, pid:6916, result:0
Aug 29 17:22:56 athlon kernel: sas: DOING DISCOVERY on port 1, pid:6916
Aug 29 17:22:56 athlon kernel: sd 4:0:0:0: [sdd] 59047936 512-byte hardware sectors: (30.2 GB/28.1 GiB)
Aug 29 17:22:56 athlon kernel: sd 4:0:0:0: [sdd] Write Protect is off
Aug 29 17:22:56 athlon kernel: sd 4:0:0:0: [sdd] Mode Sense: 00 3a 00 00
Aug 29 17:22:56 athlon kernel: sd 4:0:0:0: [sdd] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
Aug 29 17:22:56 athlon kernel:  sdd:<5>sas: sas_ata_phy_reset: Unable to reset I T nexus?
Aug 29 17:22:56 athlon kernel: sas: sas_ata_phy_reset: Found ATAPI device.
Aug 29 17:22:56 athlon kernel: ata6.00: ATAPI: HL-DT-ST DVDRAM GH20NS15, IL00, max UDMA/100
Aug 29 17:22:56 athlon kernel: mvsas 0000:02:00.0: RXQ_ERR 30000
Aug 29 17:22:56 athlon kernel: mvsas 0000:02:00.0: ATTN 80000
Aug 29 17:22:56 athlon kernel: ata6.00: configured for UDMA/100
Aug 29 17:22:56 athlon kernel: scsi 4:0:1:0: CD-ROM            HL-DT-ST DVDRAM GH20NS15  IL00 PQ: 0 ANSI: 5
Aug 29 17:22:56 athlon kernel:  sdd1
Aug 29 17:22:56 athlon kernel: sd 4:0:0:0: [sdd] Attached SCSI disk
Aug 29 17:22:56 athlon kernel: sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
Aug 29 17:22:56 athlon kernel: Uniform CD-ROM driver Revision: 3.20
Aug 29 17:22:56 athlon kernel: sr 4:0:1:0: Attached scsi CD-ROM sr0
Aug 29 17:22:56 athlon kernel: sr 4:0:1:0: Attached scsi generic sg4 type 5
Aug 29 17:22:56 athlon kernel: sas: DONE DISCOVERY on port 1, pid:6916, result:0

I can actually use both devices (a (slow) OCZ SSD, and a dvd recorder), but even during initialization, and afterwards, I get tons and tons of these:

Aug 29 17:45:17 athlon kernel: mvsas 0000:02:00.0: RXQ_ERR 20000
Aug 29 17:45:17 athlon kernel: 00000000 : 00 00 00 01 00 00 00 00 00 00 00 00 00 00 00 00 : ................

Also, I don't like the "sas_ata_phy_reset: Unable to reset I T nexus?" entries...

BTW: The driver loads fine on 2.6.30.5 x86_64, but oopses on 2.6.27.5 x86_64 (it still "works" anyway).

Unfortunately, my knowledge of Linux driver debugging ends here... If there's anything I can do to help make this card work flawlessly, I'd be glad to try it.

Thanks!
Marco

P.S.: lspci -vv goes here:

02:00.0 0107: 9005:0450 (rev 02)
Subsystem: 11ab:6440
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 4 bytes
Interrupt: pin A routed to IRQ 19
Region 2: I/O ports at ee00 [size=128]
Region 4: Memory at fdcff000 (64-bit, non-prefetchable) [size=4K]
[virtual] Expansion ROM at fdf00000 [disabled] [size=256K]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0+,D1+,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Count=1/1 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [e0] Express (v1) Legacy Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited
ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 2048 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #1, Speed 2.5GT/s, Width x4, ASPM L0s, Latency L0 <256ns, L1 unlimited
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [100] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSVoil-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSVoil-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSVoil-
CESta: RxErr+ BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
Kernel driver in use: mvsas

#1 lore raw

Hello,

following up to my earlier mail from September 4th.

Quoted 13 lines · Marco Gruß

I recently acquired an Adaptec 1405 SAS/SATA HBA.

While there is a closed-source driver by Adaptec, called adpinv, I'd of course like to get it to work with open drivers.

A lspci -v reveals that the controller is actually using a Marvell chip:

02:00.0 Serial Attached SCSI controller: Adaptec Device 0450 (rev 02)
Subsystem: Marvell Technology Group Ltd. Device 6440

02:00.0 0107: 9005:0450 (rev 02)

        Subsystem: 11ab:6440
Quoted 7 lines

(The output of lspci -vv is attached below)

So I simply added an entry for this PCI id to mvsas.c:

[...]

...with limited success:

I noticed that the mvsas driver seems to have changed quite a lot in 2.6.31, since there's now a subdir for it. I figured I'd try my simple PCI ID hack again:

usr/src/linux-2.6.31/drivers/scsi/mvsas/mv_init.c.orig 2009-09-10 00:13:59.000000000 +0200 renamed from usr/src/linux-2.6.31/drivers/scsi/mvsas/mv_init.c 2009-09-19 23:09:44.000000000 +0200 +0 -9
@@ -653,15 +653,6 @@
        { PCI_VDEVICE(MARVELL, 0x6485), chip_6485 },
        { PCI_VDEVICE(MARVELL, 0x9480), chip_9480 },
        { PCI_VDEVICE(MARVELL, 0x9180), chip_9180 },
-       {
-               .vendor         = PCI_VENDOR_ID_ADAPTEC2,
-               .device         = 0x0450,
-               .subvendor      = PCI_VENDOR_ID_MARVELL,
-               .subdevice      = 0x6440,
-               .class          = 0,
-               .class_mask     = 0,
-               .driver_data    = chip_6440,
-       },
 
        { }     /* terminate list */
 };

This time I get the following upon loading (on x86_64):

Sep 19 23:24:42 debian kernel: mvsas 0000:02:00.0: mvsas: driver version 0.8.2
Sep 19 23:24:42 debian kernel: mvsas 0000:02:00.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
Sep 19 23:24:42 debian kernel: mvsas 0000:02:00.0: setting latency timer to 64
Sep 19 23:24:42 debian kernel: mvsas 0000:02:00.0: mvsas: PCI-E x4, Bandwidth Usage: 2.5 Gbps
Sep 19 23:24:44 debian kernel: drivers/scsi/mvsas/mv_sas.c 1214:port 0 attach dev info is 0
Sep 19 23:24:44 debian kernel: drivers/scsi/mvsas/mv_sas.c 1216:port 0 attach sas addr is 0
Sep 19 23:24:44 debian kernel: drivers/scsi/mvsas/mv_sas.c 1214:port 1 attach dev info is 0
Sep 19 23:24:44 debian kernel: drivers/scsi/mvsas/mv_sas.c 1216:port 1 attach sas addr is 0
Sep 19 23:24:44 debian kernel: drivers/scsi/mvsas/mv_sas.c 1214:port 2 attach dev info is 20000
Sep 19 23:24:44 debian kernel: drivers/scsi/mvsas/mv_sas.c 1216:port 2 attach sas addr is 2
Sep 19 23:24:45 debian kernel: drivers/scsi/mvsas/mv_sas.c 1214:port 3 attach dev info is 40400
Sep 19 23:24:45 debian kernel: drivers/scsi/mvsas/mv_sas.c 1216:port 3 attach sas addr is 3
Sep 19 23:24:45 debian kernel: scsi5 : mvsas
Sep 19 23:24:45 debian kernel: drivers/scsi/mvsas/mv_sas.c 380:phy 2 byte dmaded.
Sep 19 23:24:45 debian kernel: drivers/scsi/mvsas/mv_sas.c 380:phy 3 byte dmaded.
Sep 19 23:24:45 debian kernel: sas: phy-5:2 added to port-5:0, phy_mask:0x4 ( 200000000000000)
Sep 19 23:24:45 debian kernel: sas: phy-5:3 added to port-5:1, phy_mask:0x8 ( 300000000000000)
Sep 19 23:24:45 debian kernel: sas: DOING DISCOVERY on port 0, pid:2236
Sep 19 23:24:45 debian kernel: drivers/scsi/mvsas/mv_sas.c 1365:found dev[0:5] is gone.
Sep 19 23:24:45 debian kernel: sas: sas_ata_phy_reset: Found ATA device.
Sep 19 23:24:45 debian kernel: ata7.00: ATA-7: OCZ-VERTEX, 1.3, max UDMA/133
Sep 19 23:24:45 debian kernel: ata7.00: 62533296 sectors, multi 1: LBA48 NCQ (depth 31/32)
Sep 19 23:24:45 debian kernel: ata7.00: configured for UDMA/133
Sep 19 23:24:45 debian kernel: scsi 5:0:0:0: Direct-Access     ATA      OCZ-VERTEX       1.3  PQ: 0 ANSI: 5
Sep 19 23:24:45 debian kernel: sd 5:0:0:0: Attached scsi generic sg3 type 0
Sep 19 23:24:45 debian kernel: sas: DONE DISCOVERY on port 0, pid:2236, result:0
Sep 19 23:24:45 debian kernel: sas: DOING DISCOVERY on port 1, pid:2236
Sep 19 23:24:45 debian kernel: sd 5:0:0:0: [sdd] 62533296 512-byte logical blocks: (32.0 GB/29.8 GiB)
Sep 19 23:24:45 debian kernel: sd 5:0:0:0: [sdd] Write Protect is off
Sep 19 23:24:45 debian kernel: sd 5:0:0:0: [sdd] Mode Sense: 00 3a 00 00
Sep 19 23:24:45 debian kernel: sd 5:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Sep 19 23:24:45 debian kernel:  sdd: sdd1 sdd2
Sep 19 23:24:45 debian kernel: sd 5:0:0:0: [sdd] Attached SCSI disk
Sep 19 23:24:45 debian kernel: drivers/scsi/mvsas/mv_sas.c 1365:found dev[1:5] is gone.
Sep 19 23:24:45 debian kernel: sas: sas_ata_phy_reset: Found ATAPI device.
Sep 19 23:24:45 debian kernel: ata8.00: ATAPI: HL-DT-ST DVDRAM GH20NS15, IL00, max UDMA/100
Sep 19 23:24:45 debian kernel: ata8.00: configured for UDMA/100
Sep 19 23:24:45 debian kernel: scsi 5:0:1:0: CD-ROM            HL-DT-ST DVDRAM GH20NS15  IL00 PQ: 0 ANSI: 5
Sep 19 23:24:45 debian kernel: sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
Sep 19 23:24:45 debian kernel: sr 5:0:1:0: Attached scsi CD-ROM sr0
Sep 19 23:24:45 debian kernel: sr 5:0:1:0: Attached scsi generic sg4 type 5
Sep 19 23:24:45 debian kernel: sas: DONE DISCOVERY on port 1, pid:2236, result:0

This looks much better; the performance isn't exactly stellar though.

Doing 'sync; time (dd if=/dev/zero of=1G bs=1024 count=1024k; sync)' on the SSD shows me about 40MB/s are written to disk. The same SSD achieves 150MB/s on an Intel ICH10.

Also, during this experiment, I get some of these in the syslog:

Sep 19 23:25:26 debian kernel: drivers/scsi/mvsas/mv_sas.c 2023:port 2 ctrl sts=0x199800.
Sep 19 23:25:26 debian kernel: drivers/scsi/mvsas/mv_sas.c 2025:Port 2 irq sts = 0x1000000
Sep 19 23:25:28 debian kernel: drivers/scsi/mvsas/mv_sas.c 2023:port 2 ctrl sts=0x199800.
Sep 19 23:25:28 debian kernel: drivers/scsi/mvsas/mv_sas.c 2025:Port 2 irq sts = 0x1000000
Sep 19 23:25:30 debian kernel: drivers/scsi/mvsas/mv_sas.c 2023:port 2 ctrl sts=0x199800.
Sep 19 23:25:30 debian kernel: drivers/scsi/mvsas/mv_sas.c 2025:Port 2 irq sts = 0x1000000

As stated in my previous mail: Anything I can to do help get this controller working nicely, I'll do ;-)

Thanks!

Marco
--
To unsubscribe from this list: send the line "unsubscribe linux-scsi" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html

#2 lore raw

Hello,

following up to my earlier mail from September 4th.

Quoted 13 lines · Marco Gruß

I recently acquired an Adaptec 1405 SAS/SATA HBA.

While there is a closed-source driver by Adaptec, called adpinv, I'd of course like to get it to work with open drivers.

A lspci -v reveals that the controller is actually using a Marvell chip:

02:00.0 Serial Attached SCSI controller: Adaptec Device 0450 (rev 02)
Subsystem: Marvell Technology Group Ltd. Device 6440

02:00.0 0107: 9005:0450 (rev 02)

        Subsystem: 11ab:6440
Quoted 7 lines

(The output of lspci -vv is attached below)

So I simply added an entry for this PCI id to mvsas.c:

[...]

...with limited success:

I noticed that the mvsas driver seems to have changed quite a lot in 2.6.31, since there's now a subdir for it. I figured I'd try my simple PCI ID hack again:

--- /usr/src/linux-2.6.31/drivers/scsi/mvsas/mv_init.c 2009-09-19 23:09:44.000000000 +0200
+++ /usr/src/linux-2.6.31/drivers/scsi/mvsas/mv_init.c.orig 2009-09-10
00:13:59.000000000 +0200
@@ -653,15 +653,6 @@

         { PCI_VDEVICE(MARVELL, 0x6485), chip_6485 },
         { PCI_VDEVICE(MARVELL, 0x9480), chip_9480 },
         { PCI_VDEVICE(MARVELL, 0x9180), chip_9180 },
-       {
-               .vendor         = PCI_VENDOR_ID_ADAPTEC2,
-               .device         = 0x0450,
-               .subvendor      = PCI_VENDOR_ID_MARVELL,
-               .subdevice      = 0x6440,
-               .class          = 0,
-               .class_mask     = 0,
-               .driver_data    = chip_6440,

- },

{ } /* terminate list */
};

This time I get the following upon loading (on x86_64):

Sep 19 23:24:42 debian kernel: mvsas 0000:02:00.0: mvsas: driver version
0.8.2
Sep 19 23:24:42 debian kernel: mvsas 0000:02:00.0: PCI INT A -> GSI 19
(level, low) -> IRQ 19
Sep 19 23:24:42 debian kernel: mvsas 0000:02:00.0: setting latency timer to
64
Sep 19 23:24:42 debian kernel: mvsas 0000:02:00.0: mvsas: PCI-E x4,
Bandwidth Usage: 2.5 Gbps
Sep 19 23:24:44 debian kernel: drivers/scsi/mvsas/mv_sas.c 1214:port 0
attach dev info is 0
Sep 19 23:24:44 debian kernel: drivers/scsi/mvsas/mv_sas.c 1216:port 0
attach sas addr is 0
Sep 19 23:24:44 debian kernel: drivers/scsi/mvsas/mv_sas.c 1214:port 1
attach dev info is 0
Sep 19 23:24:44 debian kernel: drivers/scsi/mvsas/mv_sas.c 1216:port 1
attach sas addr is 0
Sep 19 23:24:44 debian kernel: drivers/scsi/mvsas/mv_sas.c 1214:port 2
attach dev info is 20000
Sep 19 23:24:44 debian kernel: drivers/scsi/mvsas/mv_sas.c 1216:port 2
attach sas addr is 2
Sep 19 23:24:45 debian kernel: drivers/scsi/mvsas/mv_sas.c 1214:port 3
attach dev info is 40400
Sep 19 23:24:45 debian kernel: drivers/scsi/mvsas/mv_sas.c 1216:port 3
attach sas addr is 3
Sep 19 23:24:45 debian kernel: scsi5 : mvsas
Sep 19 23:24:45 debian kernel: drivers/scsi/mvsas/mv_sas.c 380:phy 2 byte
dmaded.
Sep 19 23:24:45 debian kernel: drivers/scsi/mvsas/mv_sas.c 380:phy 3 byte
dmaded.
Sep 19 23:24:45 debian kernel: sas: phy-5:2 added to port-5:0, phy_mask:0x4
( 200000000000000)
Sep 19 23:24:45 debian kernel: sas: phy-5:3 added to port-5:1, phy_mask:0x8
( 300000000000000)
Sep 19 23:24:45 debian kernel: sas: DOING DISCOVERY on port 0, pid:2236
Sep 19 23:24:45 debian kernel: drivers/scsi/mvsas/mv_sas.c 1365:found
dev[0:5] is gone.
Sep 19 23:24:45 debian kernel: sas: sas_ata_phy_reset: Found ATA device.
Sep 19 23:24:45 debian kernel: ata7.00: ATA-7: OCZ-VERTEX, 1.3, max UDMA/133
Sep 19 23:24:45 debian kernel: ata7.00: 62533296 sectors, multi 1: LBA48 NCQ
(depth 31/32)
Sep 19 23:24:45 debian kernel: ata7.00: configured for UDMA/133
Sep 19 23:24:45 debian kernel: scsi 5:0:0:0: Direct-Access     ATA
OCZ-VERTEX       1.3  PQ: 0 ANSI: 5
Sep 19 23:24:45 debian kernel: sd 5:0:0:0: Attached scsi generic sg3 type 0
Sep 19 23:24:45 debian kernel: sas: DONE DISCOVERY on port 0, pid:2236,
result:0
Sep 19 23:24:45 debian kernel: sas: DOING DISCOVERY on port 1, pid:2236
Sep 19 23:24:45 debian kernel: sd 5:0:0:0: [sdd] 62533296 512-byte logical
blocks: (32.0 GB/29.8 GiB)
Sep 19 23:24:45 debian kernel: sd 5:0:0:0: [sdd] Write Protect is off
Sep 19 23:24:45 debian kernel: sd 5:0:0:0: [sdd] Mode Sense: 00 3a 00 00
Sep 19 23:24:45 debian kernel: sd 5:0:0:0: [sdd] Write cache: enabled, read
cache: enabled, doesn't support DPO or FUA
Sep 19 23:24:45 debian kernel:  sdd: sdd1 sdd2
Sep 19 23:24:45 debian kernel: sd 5:0:0:0: [sdd] Attached SCSI disk
Sep 19 23:24:45 debian kernel: drivers/scsi/mvsas/mv_sas.c 1365:found
dev[1:5] is gone.
Sep 19 23:24:45 debian kernel: sas: sas_ata_phy_reset: Found ATAPI device.
Sep 19 23:24:45 debian kernel: ata8.00: ATAPI: HL-DT-ST DVDRAM GH20NS15,
IL00, max UDMA/100
Sep 19 23:24:45 debian kernel: ata8.00: configured for UDMA/100
Sep 19 23:24:45 debian kernel: scsi 5:0:1:0: CD-ROM            HL-DT-ST
DVDRAM GH20NS15  IL00 PQ: 0 ANSI: 5
Sep 19 23:24:45 debian kernel: sr0: scsi3-mmc drive: 48x/48x writer dvd-ram
cd/rw xa/form2 cdda tray
Sep 19 23:24:45 debian kernel: sr 5:0:1:0: Attached scsi CD-ROM sr0
Sep 19 23:24:45 debian kernel: sr 5:0:1:0: Attached scsi generic sg4 type 5
Sep 19 23:24:45 debian kernel: sas: DONE DISCOVERY on port 1, pid:2236,

result:0

This looks much better; the performance isn't exactly stellar though.

Doing 'sync; time (dd if=/dev/zero of=1G bs=1024 count=1024k; sync)' on the SSD shows me about 40MB/s are written to disk. The same SSD achieves 150MB/s on an Intel ICH10.

Also, during this experiment, I get some of these in the syslog:

Sep 19 23:25:26 debian kernel: drivers/scsi/mvsas/mv_sas.c 2023:port 2 ctrl
sts=0x199800.
Sep 19 23:25:26 debian kernel: drivers/scsi/mvsas/mv_sas.c 2025:Port 2 irq
sts = 0x1000000
Sep 19 23:25:28 debian kernel: drivers/scsi/mvsas/mv_sas.c 2023:port 2 ctrl
sts=0x199800.
Sep 19 23:25:28 debian kernel: drivers/scsi/mvsas/mv_sas.c 2025:Port 2 irq
sts = 0x1000000
Sep 19 23:25:30 debian kernel: drivers/scsi/mvsas/mv_sas.c 2023:port 2 ctrl
sts=0x199800.
Sep 19 23:25:30 debian kernel: drivers/scsi/mvsas/mv_sas.c 2025:Port 2 irq

sts = 0x1000000

As stated in my previous mail: Anything I can to do help get this controller working nicely, I'll do ;-)

Thanks!

Marco

CC-ing Marvell persons
Jack

--
To unsubscribe from this list: send the line "unsubscribe linux-scsi" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html

--
To unsubscribe from this list: send the line "unsubscribe linux-scsi" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html