Skip to contentSkip to conversation

UBIFS LZO decompression failure

U-Boot Simon Kagstrom 2 participants 2 messages Sep 15, 2009 – Oct 14, 2009

lore
Share & tools
lore
#0 lore raw

Hi List!

I have a slight problem with UBIFS on the OpenRD base board (an ARM board very similar to sheevaplug). Loading files which have been compressed with LZO by ubifs fails:

OpenRD>> ubi part root; ubifsmount rootfs
Creating 1 MTD partitions on "nand0":
0x0000001e0000-0x000020000000 : "mtd=1"
UBI: attaching mtd1 to ubi0

   UBI: physical eraseblock size:   131072 bytes (128 KiB)
   UBI: logical eraseblock size:    129024 bytes
   UBI: smallest flash I/O unit:    2048
   UBI: sub-page size:              512
   UBI: VID header offset:          512 (aligned 512)
   UBI: data offset:                2048
   UBI: attached mtd1 to ubi0
   UBI: MTD device name:            "mtd=1"
   UBI: MTD device size:            510 MiB
   UBI: number of good PEBs:        4081
   UBI: number of bad PEBs:         0
   UBI: max. allowed volumes:       128
   UBI: wear-leveling threshold:    4096
   UBI: number of internal volumes: 1
   UBI: number of user volumes:     1
   UBI: available PEBs:             54
   UBI: total number of reserved PEBs: 4027
   UBI: number of PEBs reserved for bad PEB handling: 40
   UBI: max/mean erase counter: 6/4
   UBIFS: mounted UBI device 0, volume 0, name "rootfs"
   UBIFS: mounted read-only
   UBIFS: file system size:   511967232 bytes (499968 KiB, 488 MiB, 3968 LEBs)
   UBIFS: journal size:       25675776 bytes (25074 KiB, 24 MiB, 199 LEBs)
   UBIFS: media format:       w4/r0 (latest is w4/r0)

UBIFS: default compressor: LZO
UBIFS: reserved for root: 5182151 bytes (5060 KiB)

OpenRD>> ubifsload 0x8000000 /boot/primary/uImage
Loading file '/boot/primary/uImage' to addr 0x08000000 with size 7196920 (0x006dd0f8)... UBIFS error (pid 0): ubifs_decompress: cannot decompress 3204 bytes, compressor LZO, error -6 UBIFS error (pid 0): read_block: bad data node (block 0, inode 88)
UBIFS error (pid 0): do_readpage: cannot read page 0 of inode 88, error -22 Error reading file '/boot/primary/uImage'

I've created the filesystem in Linux on the target (v2.6.31). The compression error -6 is LZO_E_LOOKBEHIND_OVERRUN, and it fails because of this test in lzo1x_decompress.c:

			if (HAVE_LB(m_pos, out, op))
				goto lookbehind_overrun;

where HAVE_LB is defined as (m_pos < out || m_pos >= op) and the m_pos, out and op values are 0x07ffde77, 0x08000000, 0x08000083 (i.e., the first test fails).

The lzo1x_decompress.c file is identical to that in Linux, so something is fishy here. Does it work for the rest of you?

In our case it doesn't matter very much since the file (an uImage) is compressed anyway and we therefore save work anyway by marking it as using no compression, but it would be nice if this would work anyhow.

// Simon

#1 lore raw
Quoted 9 lines · Simon Kagstrom <simon.kagstrom <at> netinsight.net> writes:

Hi List!

I have a slight problem with UBIFS on the OpenRD base board (an ARM board very similar to sheevaplug). Loading files which have been compressed with LZO by ubifs fails:

OpenRD>> ubifsload 0x8000000 /boot/primary/uImage
Loading file '/boot/primary/uImage' to addr 0x08000000 with size 7196920

(0x006dd0f8)...

Quoted 1 line

UBIFS error (pid 0): ubifs_decompress: cannot decompress 3204 bytes,

compressor LZO, error -6

Quoted 11 lines

UBIFS error (pid 0): read_block: bad data node (block 0, inode 88) UBIFS error (pid 0): do_readpage: cannot read page 0 of inode 88, error -22 Error reading file '/boot/primary/uImage'

I've created the filesystem in Linux on the target (v2.6.31). The compression error -6 is LZO_E_LOOKBEHIND_OVERRUN, and it fails because of this test in lzo1x_decompress.c:

			if (HAVE_LB(m_pos, out, op))
				goto lookbehind_overrun;
Quoted 9 lines

where HAVE_LB is defined as (m_pos < out || m_pos >= op) and the m_pos, out and op values are 0x07ffde77, 0x08000000, 0x08000083 (i.e., the first test fails).

The lzo1x_decompress.c file is identical to that in Linux, so something is fishy here. Does it work for the rest of you?

// Simon

Hello,

Just looking around and found this message. I am also getting the same error.

Does anyone have any more info on it? for example what causes a look behind overrun?

Thanks in advance

Mark Retallack.