Skip to contentSkip to conversation

Raid 5 Issue, cannot recognize EXT3 File system.

DISCUSSION Sunpyo Hong 3 participants 5 messages Sep 17, 2009 – Sep 18, 2009 MD RAID

lore
Share & tools
lore
#0 lore raw

I’ve contacted just about everyone that knows a thing about RAID5, but no one is really able to help me. Anyhow I’ve read up a lot on RAID5 arrays and how to properly assemble them. However I’ve run into a problem with a NAS system from WD that I just can’t seem to figure out.

I have a ¾ disks in the array, 1 went down and is out of commission. I’ve been able to assemble my array through mdadm using –assemble –scan. However I cannot access the array due to the fact that the array cannot read a filesystem. Everytime I try to mount I get mount: wrong fs type… etc. I know that the FS is an ext3 FS. However I cannot seem to get this thing going. I was wondering if anyone could point me in the right direction with this. I can’t seem to find anyone that is capable of solving this. I would appreciate any help. Thanks!

-Sunpyo

--
To unsubscribe from this list: send the line "unsubscribe linux-raid" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html

#1 lore raw
Quoted 5 lines · Sunpyo Hong

I've contacted just about everyone that knows a thing about RAID5, but no one is really able to help me. Anyhow I've read up a lot on RAID5 arrays and how to properly assemble them. However I've run into a problem with a NAS system from WD that I just can't seem to figure out.

Quoted 9 lines

I have a ¾ disks in the array, 1 went down and is out of commission. I've been able to assemble my array through mdadm using --assemble --scan. However I cannot access the array due to the fact that the array cannot read a filesystem. Everytime I try to mount I get mount: wrong fs type… etc. I know that the FS is an ext3 FS. However I cannot seem to get this thing going. I was wondering if anyone could point me in the right direction with this. I can't seem to find anyone that is capable of solving this. I would appreciate any help. Thanks!

What's the output of 'cat /proc/mdstat' after you assemble the array? And what exact error (and dmesg output) do you get when trying to mount it as ext3?

Cheers,
Robin

Signature · 4 lines
     ___        
    ( ' }     |       Robin Hill        <[email protected]> |
   / / )      | Little Jim says ....                            |
  // !!       |      "He fallen in de water !!"                 |
#2 lore raw

This NAS from WD, does it use Linux's software RAID?
If not, you can't assemble it under Linux, because the RAID controller is using proprietary methods.

Quoted 28 lines · Robin Hill
Quoted 5 lines · Sunpyo Hong

I've contacted just about everyone that knows a thing about RAID5, but no one is really able to help me. Anyhow I've read up a lot on RAID5 arrays and how to properly assemble them. However I've run into a problem with a NAS system from WD that I just can't seem to figure out.

Quoted 9 lines

I have a ¾ disks in the array, 1 went down and is out of commission.  I've been able to assemble my array through mdadm using --assemble --scan. However I cannot access the array due to the fact that the array cannot read a filesystem. Everytime I try to mount I get mount: wrong fs type… etc. I know that the FS is an ext3 FS. However I cannot seem to get this thing going. I was wondering if anyone could point me in the right direction with this. I can't seem to find anyone that is capable of solving this. I would appreciate any help. Thanks!

What's the output of 'cat /proc/mdstat' after you assemble the array? And what exact error (and dmesg output) do you get when trying to mount it as ext3?

Cheers,
   Robin
--
    ___

   ( ' }     |       Robin Hill        <[email protected]> |
  / / )      | Little Jim says ....                            |
 // !!       |      "He fallen in de water !!"                 |
Signature · 5 lines
       Majed B.
--
To unsubscribe from this list: send the line "unsubscribe linux-raid" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html
#3 lore raw
In reply to Robin Hill

First off, lemme tell you the initial problem. I had a WD ShareSpace that had one of the disk go bad. They sent a replacement and it was suppose to rebuild on its own, however after the build, the array went bad and it was no longer able to see any of the files.

I downloaded and tested the drives using windows data recovery tools I saw that the ext3 was Linux FS and that using these tools would not help in the recovery. However through the tools I was able to see and recover some of the files, but the files themselves were usable. I confirmed with WD that ext3 was in fact the FS and took steps to recover the data. These are the steps I took in order for me to assemble the raid.

Right now I have 3/4 drives with the data. I did #mdadm --assemble --scan, which let me assemble the raid. However at this point I was not able to see any of the files or mount the drive to the mount point it was once at. I have also tried #mdadm --create with the array in the right order /w the missing disk.

Initially the --assemble --scan assembled the array /dev/md2 with the disks in the wrong order. I know because I physically saw where the disks were in relation to the disk order and wrote down the disk order on every HD.

Here's everything I could find in terms of information that you asked for. It's a lot.

#dmesg

[  339.440187] raid5: device sdb4 operational as raid disk 1
[  339.440189] raid5: device sdd4 operational as raid disk 3
[  339.440192] raid5: device sdc4 operational as raid disk 2
[  339.440610] raid5: allocated 4219kB for md2
[  339.440612] raid5: raid level 5 set md2 active with 3 out of 4 devices,
algorithm 2
[  339.440615] RAID5 conf printout:
[  339.440617]  --- rd:4 wd:3
[  339.440619]  disk 1, o:1, dev:sdb4
[  339.440620]  disk 2, o:1, dev:sdc4
[  339.440622]  disk 3, o:1, dev:sdd4
[  339.440817]  md2: unknown partition table
[  538.840033] kjournald starting.  Commit interval 5 seconds
[  538.891844] EXT3 FS on md0, internal journal
[  538.891849] EXT3-fs: mounted filesystem with ordered data mode.
[  581.585031] VFS: Can't find ext4 filesystem on dev md2.
[  587.056825] VFS: Can't find ext3 filesystem on dev md2.

#fdisk -l
WARNING: GPT (GUID Partition Table) detected on '/dev/sda'! The util fdisk doesn't support GPT. Use GNU Parted.

Disk /dev/sda: 2000.3 GB, 2000398934016 bytes
255 heads, 63 sectors/track, 243201 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk identifier: 0x00000000

   Device Boot      Start         End      Blocks   Id  System
/dev/sda1               1      243202  1953514583+  ee  GPT

Disk /dev/sdb: 2000.3 GB, 2000398934016 bytes
255 heads, 63 sectors/track, 243201 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk identifier: 0xdd07e5e3

   Device Boot      Start         End      Blocks   Id  System
/dev/sdb1               1          26      208844+  fd  Linux raid

autodetect
/dev/sdb2 27 156 1044225 fd Linux raid
autodetect
/dev/sdb3 157 182 208845 fd Linux raid
autodetect
/dev/sdb4 183 243201 1952050117+ fd Linux raid
autodetect

Disk /dev/sdc: 2000.3 GB, 2000398934016 bytes
255 heads, 63 sectors/track, 243201 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk identifier: 0xdd07e5e4

   Device Boot      Start         End      Blocks   Id  System
/dev/sdc1               1          26      208844+  fd  Linux raid

autodetect
/dev/sdc2 27 156 1044225 fd Linux raid
autodetect
/dev/sdc3 157 182 208845 fd Linux raid
autodetect
/dev/sdc4 183 243201 1952050117+ fd Linux raid
autodetect

Disk /dev/sdd: 2000.3 GB, 2000398934016 bytes
255 heads, 63 sectors/track, 243201 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk identifier: 0xdd07e5e2

   Device Boot      Start         End      Blocks   Id  System
/dev/sdd1               1          26      208844+  fd  Linux raid

autodetect
/dev/sdd2 27 156 1044225 fd Linux raid
autodetect
/dev/sdd3 157 182 208845 fd Linux raid
autodetect
/dev/sdd4 183 243201 1952050117+ fd Linux raid
autodetect

Disk /dev/md0: 213 MB, 213778432 bytes
2 heads, 4 sectors/track, 52192 cylinders
Units = cylinders of 8 * 512 = 4096 bytes
Disk identifier: 0x00000000

Disk /dev/md0 doesn't contain a valid partition table

Disk /dev/md2: 5996.6 GB, 5996697747456 bytes
2 heads, 4 sectors/track, 1464037536 cylinders
Units = cylinders of 8 * 512 = 4096 bytes
Disk identifier: 0x00000000

Disk /dev/md2 doesn't contain a valid partition table

#cat /proc/mdstat
Personalities : [raid1] [raid6] [raid5] [raid4]
md2 : active raid5 sdb4[1] sdd4[3] sdc4[2]

      5856150144 blocks level 5, 64k chunk, algorithm 2 [4/3] [_UUU]

md0 : active raid1 sdd1[0] sdb1[2] sdc1[1]

      208768 blocks [4/3] [UUU_]

#cat /etc/fstab
aufs / aufs rw 0 0
tmpfs /tmp tmpfs nosuid,nodev 0 0
/dev/sda2 swap swap defaults 0 0
/dev/sdb2 swap swap defaults 0 0
/dev/sdc2 swap swap defaults 0 0
/dev/sdd2 swap swap defaults 0 0

#mount -t ext3 /dev/md2 /media/disk/shares
mount: wrong fs type, bad option, bad superblock on /dev/md2,
missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so

#mdadm -Ds -v
ARRAY /dev/md0 level=raid1 num-devices=4 metadata=00.90 UUID=15e54255:f58be7ca:7f4a592f:038fedf2
devices=/dev/sdd1,/dev/sdc1,/dev/sdb1
ARRAY /dev/md2 level=raid5 num-devices=4 metadata=00.90 UUID=0b23d5e1:f5a27618:e368bf24:bd0fce41
devices=/dev/sdb4,/dev/sdc4,/dev/sdd4

#mdadm -Es -v
ARRAY /dev/md0 level=raid1 num-devices=4
UUID=15e54255:f58be7ca:7f4a592f:038fedf2
devices=/dev/sdd1,/dev/sdc1,/dev/sdb1
ARRAY /dev/md1 level=raid1 num-devices=4
UUID=57cd5e76:0d56f114:50bd5336:4477d020
devices=/dev/sdd2,/dev/sdc2,/dev/sdb2
ARRAY /dev/md2 level=raid5 num-devices=4
UUID=0b23d5e1:f5a27618:e368bf24:bd0fce41
devices=/dev/sdd4,/dev/sdc4,/dev/sdb4

-----Original Message-----
From: [email protected] [mailto:[email protected]] On Behalf Of Robin Hill
Sent: Thursday, September 17, 2009 5:02 PM
To: [email protected]
Subject: Re: Raid 5 Issue, cannot recognize EXT3 File system.

Quoted 2 lines · Sunpyo Hong

I've contacted just about everyone that knows a thing about RAID5, but no one is really able to help me. Anyhow I've read up a lot on RAID5 arrays

and

Quoted 5 lines

how to properly assemble them. However I've run into a problem with a NAS system from WD that I just can't seem to figure out.

I have a ¾ disks in the array, 1 went down and is out of commission. I've been able to assemble my array through mdadm using --assemble --scan.

However

Quoted 7 lines

I cannot access the array due to the fact that the array cannot read a filesystem. Everytime I try to mount I get mount: wrong fs type… etc. I know that the FS is an ext3 FS. However I cannot seem to get this thing going. I was wondering if anyone could point me in the right direction with this. I can't seem to find anyone that is capable of solving this. I would appreciate any help. Thanks!

What's the output of 'cat /proc/mdstat' after you assemble the array? And what exact error (and dmesg output) do you get when trying to mount it as ext3?

Cheers,
Robin

Signature · 9 lines
     ___        
    ( ' }     |       Robin Hill        <[email protected]> |
   / / )      | Little Jim says ....                            |
  // !!       |      "He fallen in de water !!"                 |

--
To unsubscribe from this list: send the line "unsubscribe linux-raid" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html
#4 lore raw
Quoted 18 lines · Sunpyo Hong

First off, lemme tell you the initial problem. I had a WD ShareSpace that had one of the disk go bad. They sent a replacement and it was suppose to rebuild on its own, however after the build, the array went bad and it was no longer able to see any of the files.

I downloaded and tested the drives using windows data recovery tools I saw that the ext3 was Linux FS and that using these tools would not help in the recovery. However through the tools I was able to see and recover some of the files, but the files themselves were usable. I confirmed with WD that ext3 was in fact the FS and took steps to recover the data. These are the steps I took in order for me to assemble the raid.

Right now I have 3/4 drives with the data. I did #mdadm --assemble --scan, which let me assemble the raid. However at this point I was not able to see any of the files or mount the drive to the mount point it was once at. I have also tried #mdadm --create with the array in the right order /w the missing disk.

Quoted 4 lines

Initially the --assemble --scan assembled the array /dev/md2 with the disks in the wrong order. I know because I physically saw where the disks were in relation to the disk order and wrote down the disk order on every HD.

This should not be possible - --assemble will read the metadata from the superblocks and determine the order the drives should be within the array. The physical positioning/ordering is irrelevant here. I suggest you recreate the array in the original order --assemble did (and hope that the chunk size used is the default).

Quoted 8 lines

#cat /proc/mdstat
Personalities : [raid1] [raid6] [raid5] [raid4]
md2 : active raid5 sdb4[1] sdd4[3] sdc4[2]

      5856150144 blocks level 5, 64k chunk, algorithm 2 [4/3] [_UUU]

md0 : active raid1 sdd1[0] sdb1[2] sdc1[1]

      208768 blocks [4/3] [UUU_]

I find it somewhat odd that md0 and md2 have the drives in a different order. Is this related to your recreating the array? Admittedly, md0 is only a RAID1 so the order doesn't actually matter, but if the arrays were created at the same time then the normal behaviour would be to use the same order in the create command.

Cheers,
Robin

Signature · 4 lines
     ___        
    ( ' }     |       Robin Hill        <[email protected]> |
   / / )      | Little Jim says ....                            |
  // !!       |      "He fallen in de water !!"                 |