Skip to contentSkip to conversation

Kernel hangs...

U-Boot Michael Schmid 2 participants 2 messages Oct 17, 2009

lore
Share & tools
lore
#0 lore raw

Hi!

I have the following system:
- Board: Artila M-501 with Atmel AT91RM9200
- 16MB Flash
- 64MB SDRAM
- U-Boot 1.1.2
- Linux: 2.6

I am new to those bootloader and embedded linux things, so I messed up the configuration of u-boot... Then I recovered the Board with new loader, environment and new kernel and ramdisk -> I used the official "recovery package" of Artila (I know that it wouldn't have been necessary to do all the things, but I wasn't sure if the bootloader was the only problem...)

So now it starts but after a while it hangs after the following message:
--- Start ---
Starting M501.............
Starting kernel ...

Uncompressing Linux............................................................................................... done, booting the kernel.
--- End ---

I have the following conf. in U-Boot:
--- Start ---
Artila> printenv
baudrate=115200
ethaddr=00:13:48:00:77:b5
rootpath=/opt/arm
lel=1
initrd=0x20800000,8192000 ramdisk_size=15360 root=/dev/ram0 rw loader=tftp 21000000 m501_64M.alf mtdparts=phys_mapped_flash:128k(loader)ro,128k(reserved)ro,1408k(linux)ro,2560(r amdisk)ro,-(userdisk)
filesize=3A3
gateway=192.168.1.1
netmask=255.255.255.0
bootcmd=bootm 10040000 101a0000
kernel=tftp 21000000 M501K;erase 10040000 1019ffff;cp.b 21000000 10040000 $(file size)
skernel=loadb 21000000;erase 10040000 1019ffff;cp.b 21000000 10040000 $(filesize )
ramdisk=tftp 21000000 M501R;erase 101a0000 1041ffff;cp.b 21000000 101a0000 $(fil esize)
sramdisk=loadb 21000000;erase 101a0000 1041ffff;cp.b 21000000 101a0000 $(filesiz
e)
serverip=192.168.2.150
ipaddr=192.168.2.196
bootdelay=1
bargs=setenv bootargs mem=64M console=$(console),115200 initrd=0x20800000,819200 0 ramdisk_size=15360 root=/dev/ram0 rw mtdparts=phys_mapped_flash:128k(loader)ro ,128k(env)ro,1408k(linux)ro,2560k(ramdisk)ro,-(userdisk) bootargs=mem=64M console=NULL,115200 initrd=0x20800000,8192000 ramdisk_size=1536 0 root=/dev/ram0 rw mtdparts=phys_mapped_flash:128k(loader)ro,128k(reserved)ro,1 408k(linux)ro,2560k(ramdisk)ro,-(userdisk)
console=ttyS0
stdin=serial
stdout=serial
stderr=serial
--- End ---

bdinfo gives the following output:
--- Start ---
Artila> bdinfo
arch_number = 0x00000537
env_t = 0x00000000
boot_params = 0x20000100

DRAM bank   = 0x00000000
-> start    = 0x20000000
-> size     = 0x02000000
ethaddr     = 00:13:48:00:77:B5
ip_addr     = 192.168.2.196
baudrate    = 115200 bps
flash size  = 16 MB

--- End ---

What could be the problem? How can I find out where the problem is? --> Is it possible that the kernel hangs because of a hardware-bug?

Thanks for every hint!
Michael

Signature · 2 lines
Jetzt kostenlos herunterladen: Internet Explorer 8 und Mozilla Firefox 3.5 -
sicherer, schneller und einfacher! http://portal.gmx.net/de/go/atbrowser
#1 lore raw

Hi Michael,

Quoted 10 lines · Michael Schmid

Hi!

I have the following system:
- Board: Artila M-501 with Atmel AT91RM9200
- 16MB Flash
- 64MB SDRAM
- U-Boot 1.1.2
- Linux: 2.6

I don't have any experience with this hardware, but it sure looks like a

console problem.

Quoted 46 lines

I am new to those bootloader and embedded linux things, so I messed up the configuration of u-boot... Then I recovered the Board with new loader, environment and new kernel and ramdisk -> I used the official "recovery package" of Artila (I know that it wouldn't have been necessary to do all the things, but I wasn't sure if the bootloader was the only problem...)

So now it starts but after a while it hangs after the following message:
--- Start ---
Starting M501.............
Starting kernel ...

Uncompressing

Linux............................................................................................... done, booting the kernel.
--- End ---

I have the following conf. in U-Boot:
--- Start ---
Artila> printenv
baudrate=115200
ethaddr=00:13:48:00:77:b5
rootpath=/opt/arm
lel=1
initrd=0x20800000,8192000 ramdisk_size=15360 root=/dev/ram0 rw loader=tftp 21000000 m501_64M.alf

mtdparts=phys_mapped_flash:128k(loader)ro,128k(reserved)ro,1408k(linux)ro,2560(r amdisk)ro,-(userdisk)
filesize=3A3
gateway=192.168.1.1
netmask=255.255.255.0
bootcmd=bootm 10040000 101a0000
kernel=tftp 21000000 M501K;erase 10040000 1019ffff;cp.b 21000000 10040000 $(file
size)
skernel=loadb 21000000;erase 10040000 1019ffff;cp.b 21000000 10040000 $(filesize
)
ramdisk=tftp 21000000 M501R;erase 101a0000 1041ffff;cp.b 21000000 101a0000 $(fil
esize)
sramdisk=loadb 21000000;erase 101a0000 1041ffff;cp.b 21000000 101a0000 $(filesiz
e)
serverip=192.168.2.150

Quoted 8 lines

ipaddr=192.168.2.196
bootdelay=1
bargs=setenv bootargs mem=64M console=$(console),115200 initrd=0x20800000,819200
0 ramdisk_size=15360 root=/dev/ram0 rw mtdparts=phys_mapped_flash:128k(loader)ro ,128k(env)ro,1408k(linux)ro,2560k(ramdisk)ro,-(userdisk) bootargs=mem=64M console=NULL,115200 initrd=0x20800000,8192000

console=NULL looks suspicious... It's been a while, but I think when 'bootcmd' is executed, it uses 'bootargs' as the kernel command line parameters. If that's the case, you're telling the kernel there's no console. It looks like somebody created a 'bargs' command that sets bootargs to something different. You may want to try running it before 'boot'

Quoted 25 lines

ramdisk_size=1536
0 root=/dev/ram0 rw mtdparts=phys_mapped_flash:128k(loader)ro,128k(reserved)ro,1 408k(linux)ro,2560k(ramdisk)ro,-(userdisk) console=ttyS0
stdin=serial
stdout=serial
stderr=serial
--- End ---

bdinfo gives the following output:
--- Start ---
Artila> bdinfo
arch_number = 0x00000537
env_t = 0x00000000
boot_params = 0x20000100

DRAM bank   = 0x00000000
-> start    = 0x20000000
-> size     = 0x02000000
ethaddr     = 00:13:48:00:77:B5
ip_addr     = 192.168.2.196
baudrate    = 115200 bps
flash size  = 16 MB

--- End ---

Quoted 8 lines

What could be the problem? How can I find out where the problem is? --> Is it possible that the kernel hangs because of a hardware-bug?

The stuff I wrote above may be incorrect, but hopefully gets you thinking.

Thanks for every hint!
Michael

regards,
Ben