Skip to contentSkip to conversation

use gen_nand

PATCH In review Ladislav Michl 3 participants 5 messages Nov 23, 2009 – Dec 4, 2009

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 use gen_nand

Since omapnand driver never find its way into mainline, switch to gen_nand instead. Following patch is compile tested only, but it is based on code I wrote for NetStar board and runtime tested it there.

Cc Imre Deak <[email protected]>
Cc Brian Swetland <[email protected]>
Cc Kevin Hilman <[email protected]>
arch/arm/mach-omap1/board-fsample.c +37 -13
index f4b72c1..8da8c64 100644
@@ -30,7 +30,6 @@
 #include <mach/gpio.h>
 #include <plat/mux.h>
 #include <plat/fpga.h>
-#include <plat/nand.h>
 #include <plat/keypad.h>
 #include <plat/common.h>
 #include <plat/board.h>
@@ -167,8 +166,40 @@ static struct platform_device nor_device = {
 	.resource	= &nor_resource,
 };
 
-static struct omap_nand_platform_data nand_data = {
-	.options	= NAND_SAMSUNG_LP_OPTIONS,
+static void nand_cmd_ctl(struct mtd_info *mtd, int cmd,	unsigned int ctrl)
+{
+	struct nand_chip *this = mtd->priv;
+	unsigned long mask;
+
+	if (cmd == NAND_CMD_NONE)
+		return;
+
+	mask = (ctrl & NAND_CLE) ? 0x02 : 0;
+	if (ctrl & NAND_ALE)
+		mask |= 0x04;
+	writeb(cmd, (unsigned long)this->IO_ADDR_W | mask);
+}
+
+#define FSAMPLE_NAND_RB_GPIO_PIN	62
+
+static int nand_dev_ready(struct mtd_info *mtd)
+{
+	return gpio_get_value(FSAMPLE_NAND_RB_GPIO_PIN);
+}
+
+static const char *part_probes[] = { "cmdlinepart", NULL };
+
+static struct platform_nand_data nand_data = {
+	.chip	= {
+		.nr_chips		= 1,
+		.chip_offset		= 0,
+		.options		= NAND_SAMSUNG_LP_OPTIONS,
+		.part_probe_types	= part_probes,
+	},
+	.ctrl	= {
+		.cmd_ctrl	= nand_cmd_ctl,
+		.dev_ready	= nand_dev_ready,
+	},
 };
 
 static struct resource nand_resource = {
@@ -178,7 +209,7 @@ static struct resource nand_resource = {
 };
 
 static struct platform_device nand_device = {
-	.name		= "omapnand",
+	.name		= "gen_nand",
 	.id		= 0,
 	.dev		= {
 		.platform_data	= &nand_data,
@@ -233,13 +264,6 @@ static struct platform_device *devices[] __initdata = {
 	&lcd_device,
 };
 
-#define P2_NAND_RB_GPIO_PIN	62
-
-static int nand_dev_ready(struct omap_nand_platform_data *data)
-{
-	return gpio_get_value(P2_NAND_RB_GPIO_PIN);
-}
-
 static struct omap_lcd_config fsample_lcd_config __initdata = {
 	.ctrl_name	= "internal",
 };
@@ -250,9 +274,9 @@ static struct omap_board_config_kernel fsample_config[] = {
 
 static void __init omap_fsample_init(void)
 {
-	if (gpio_request(P2_NAND_RB_GPIO_PIN, "NAND ready") < 0)
+	if (gpio_request(FSAMPLE_NAND_RB_GPIO_PIN, "NAND ready") < 0)
 		BUG();
-	nand_data.dev_ready = nand_dev_ready;
+	gpio_direction_input(FSAMPLE_NAND_RB_GPIO_PIN);
 
 	omap_cfg_reg(L3_1610_FLASH_CS2B_OE);
 	omap_cfg_reg(M8_1610_FLASH_CS2B_WE);
arch/arm/mach-omap1/board-h2.c +39 -10

75 lines not on this page · raw message

arch/arm/mach-omap1/board-h3.c +40 -16

88 lines not on this page · raw message

arch/arm/mach-omap1/board-perseus2.c +36 -12

78 lines not on this page · raw message

reviewer
#1 lore raw
Quoted 3 lines · Ladislav Michl

Since omapnand driver never find its way into mainline, switch to gen_nand instead. Following patch is compile tested only, but it is based on code I wrote for NetStar board and runtime tested it there.

Nice patch, and totally the way to go!

Regards,

Tony

Quoted 366 lines
Cc Imre Deak <[email protected]>
Cc Brian Swetland <[email protected]>
Cc Kevin Hilman <[email protected]>
arch/arm/mach-omap1/board-fsample.c +37 -13
index f4b72c1..8da8c64 100644
@@ -30,7 +30,6 @@
 #include <mach/gpio.h>
 #include <plat/mux.h>
 #include <plat/fpga.h>
-#include <plat/nand.h>
 #include <plat/keypad.h>
 #include <plat/common.h>
 #include <plat/board.h>
@@ -167,8 +166,40 @@ static struct platform_device nor_device = {
 	.resource	= &nor_resource,
 };
 
-static struct omap_nand_platform_data nand_data = {
-	.options	= NAND_SAMSUNG_LP_OPTIONS,
+static void nand_cmd_ctl(struct mtd_info *mtd, int cmd,	unsigned int ctrl)
+{
+	struct nand_chip *this = mtd->priv;
+	unsigned long mask;
+
+	if (cmd == NAND_CMD_NONE)
+		return;
+
+	mask = (ctrl & NAND_CLE) ? 0x02 : 0;
+	if (ctrl & NAND_ALE)
+		mask |= 0x04;
+	writeb(cmd, (unsigned long)this->IO_ADDR_W | mask);
+}
+
+#define FSAMPLE_NAND_RB_GPIO_PIN	62
+
+static int nand_dev_ready(struct mtd_info *mtd)
+{
+	return gpio_get_value(FSAMPLE_NAND_RB_GPIO_PIN);
+}
+
+static const char *part_probes[] = { "cmdlinepart", NULL };
+
+static struct platform_nand_data nand_data = {
+	.chip	= {
+		.nr_chips		= 1,
+		.chip_offset		= 0,
+		.options		= NAND_SAMSUNG_LP_OPTIONS,
+		.part_probe_types	= part_probes,
+	},
+	.ctrl	= {
+		.cmd_ctrl	= nand_cmd_ctl,
+		.dev_ready	= nand_dev_ready,
+	},
 };
 
 static struct resource nand_resource = {
@@ -178,7 +209,7 @@ static struct resource nand_resource = {
 };
 
 static struct platform_device nand_device = {
-	.name		= "omapnand",
+	.name		= "gen_nand",
 	.id		= 0,
 	.dev		= {
 		.platform_data	= &nand_data,
@@ -233,13 +264,6 @@ static struct platform_device *devices[] __initdata = {
 	&lcd_device,
 };
 
-#define P2_NAND_RB_GPIO_PIN	62
-
-static int nand_dev_ready(struct omap_nand_platform_data *data)
-{
-	return gpio_get_value(P2_NAND_RB_GPIO_PIN);
-}
-
 static struct omap_lcd_config fsample_lcd_config __initdata = {
 	.ctrl_name	= "internal",
 };
@@ -250,9 +274,9 @@ static struct omap_board_config_kernel fsample_config[] = {
 
 static void __init omap_fsample_init(void)
 {
-	if (gpio_request(P2_NAND_RB_GPIO_PIN, "NAND ready") < 0)
+	if (gpio_request(FSAMPLE_NAND_RB_GPIO_PIN, "NAND ready") < 0)
 		BUG();
-	nand_data.dev_ready = nand_dev_ready;
+	gpio_direction_input(FSAMPLE_NAND_RB_GPIO_PIN);
 
 	omap_cfg_reg(L3_1610_FLASH_CS2B_OE);
 	omap_cfg_reg(M8_1610_FLASH_CS2B_WE);
arch/arm/mach-omap1/board-h2.c +39 -10
index 89ba8ec..283a6f2 100644
@@ -40,7 +40,6 @@
 #include <plat/mux.h>
 #include <plat/dma.h>
 #include <plat/tc.h>
-#include <plat/nand.h>
 #include <plat/irda.h>
 #include <plat/usb.h>
 #include <plat/keypad.h>
@@ -179,11 +178,43 @@ static struct mtd_partition h2_nand_partitions[] = {
 	},
 };
 
-/* dip switches control NAND chip access:  8 bit, 16 bit, or neither */
-static struct omap_nand_platform_data h2_nand_data = {
-	.options	= NAND_SAMSUNG_LP_OPTIONS,
-	.parts		= h2_nand_partitions,
-	.nr_parts	= ARRAY_SIZE(h2_nand_partitions),
+static void h2_nand_cmd_ctl(struct mtd_info *mtd, int cmd, unsigned int ctrl)
+{
+	struct nand_chip *this = mtd->priv;
+	unsigned long mask;
+
+	if (cmd == NAND_CMD_NONE)
+		return;
+
+	mask = (ctrl & NAND_CLE) ? 0x02 : 0;
+	if (ctrl & NAND_ALE)
+		mask |= 0x04;
+	writeb(cmd, (unsigned long)this->IO_ADDR_W | mask);
+}
+
+#define H2_NAND_RB_GPIO_PIN	62
+
+static int h2_nand_dev_ready(struct mtd_info *mtd)
+{
+	return gpio_get_value(H2_NAND_RB_GPIO_PIN);
+}
+
+static const char *h2_part_probes[] = { "cmdlinepart", NULL };
+
+struct platform_nand_data h2_nand_platdata = {
+	.chip	= {
+		.nr_chips		= 1,
+		.chip_offset		= 0,
+		.nr_partitions		= ARRAY_SIZE(h2_nand_partitions),
+		.partitions		= h2_nand_partitions,
+		.options		= NAND_SAMSUNG_LP_OPTIONS,
+		.part_probe_types	= h2_part_probes,
+	},
+	.ctrl	= {
+		.cmd_ctrl	= h2_nand_cmd_ctl,
+		.dev_ready	= h2_nand_dev_ready,
+
+	},
 };
 
 static struct resource h2_nand_resource = {
@@ -191,10 +222,10 @@ static struct resource h2_nand_resource = {
 };
 
 static struct platform_device h2_nand_device = {
-	.name		= "omapnand",
+	.name		= "gen_nand",
 	.id		= 0,
 	.dev		= {
-		.platform_data	= &h2_nand_data,
+		.platform_data	= &h2_nand_platdata,
 	},
 	.num_resources	= 1,
 	.resource	= &h2_nand_resource,
@@ -368,8 +399,6 @@ static struct omap_board_config_kernel h2_config[] __initdata = {
 	{ OMAP_TAG_LCD,		&h2_lcd_config },
 };
 
-#define H2_NAND_RB_GPIO_PIN	62
-
 static void __init h2_init(void)
 {
 	/* Here we assume the NOR boot config:  NOR on CS3 (possibly swapped
arch/arm/mach-omap1/board-h3.c +40 -16
index f5cc0a7..f96cd1e 100644
@@ -42,7 +42,6 @@
 #include <mach/irqs.h>
 #include <plat/mux.h>
 #include <plat/tc.h>
-#include <plat/nand.h>
 #include <plat/usb.h>
 #include <plat/keypad.h>
 #include <plat/dma.h>
@@ -181,11 +180,43 @@ static struct mtd_partition nand_partitions[] = {
 	},
 };
 
-/* dip switches control NAND chip access:  8 bit, 16 bit, or neither */
-static struct omap_nand_platform_data nand_data = {
-	.options	= NAND_SAMSUNG_LP_OPTIONS,
-	.parts		= nand_partitions,
-	.nr_parts	= ARRAY_SIZE(nand_partitions),
+static void nand_cmd_ctl(struct mtd_info *mtd, int cmd, unsigned int ctrl)
+{
+	struct nand_chip *this = mtd->priv;
+	unsigned long mask;
+
+	if (cmd == NAND_CMD_NONE)
+		return;
+
+	mask = (ctrl & NAND_CLE) ? 0x02 : 0;
+	if (ctrl & NAND_ALE)
+		mask |= 0x04;
+	writeb(cmd, (unsigned long)this->IO_ADDR_W | mask);
+}
+
+#define H3_NAND_RB_GPIO_PIN	10
+
+static int nand_dev_ready(struct mtd_info *mtd)
+{
+	return gpio_get_value(H3_NAND_RB_GPIO_PIN);
+}
+
+static const char *part_probes[] = { "cmdlinepart", NULL };
+
+struct platform_nand_data nand_platdata = {
+	.chip	= {
+		.nr_chips		= 1,
+		.chip_offset		= 0,
+		.nr_partitions		= ARRAY_SIZE(nand_partitions),
+		.partitions		= nand_partitions,
+		.options		= NAND_SAMSUNG_LP_OPTIONS,
+		.part_probe_types	= part_probes,
+	},
+	.ctrl	= {
+		.cmd_ctrl	= nand_cmd_ctl,
+		.dev_ready	= nand_dev_ready,
+
+	},
 };
 
 static struct resource nand_resource = {
@@ -193,10 +224,10 @@ static struct resource nand_resource = {
 };
 
 static struct platform_device nand_device = {
-	.name		= "omapnand",
+	.name		= "gen_nand",
 	.id		= 0,
 	.dev		= {
-		.platform_data	= &nand_data,
+		.platform_data	= &nand_platdata,
 	},
 	.num_resources	= 1,
 	.resource	= &nand_resource,
@@ -332,13 +363,6 @@ static struct i2c_board_info __initdata h3_i2c_board_info[] = {
 	},
 };
 
-#define H3_NAND_RB_GPIO_PIN	10
-
-static int nand_dev_ready(struct omap_nand_platform_data *data)
-{
-	return gpio_get_value(H3_NAND_RB_GPIO_PIN);
-}
-
 static void __init h3_init(void)
 {
 	/* Here we assume the NOR boot config:  NOR on CS3 (possibly swapped
@@ -356,7 +380,7 @@ static void __init h3_init(void)
 	nand_resource.end += SZ_4K - 1;
 	if (gpio_request(H3_NAND_RB_GPIO_PIN, "NAND ready") < 0)
 		BUG();
-	nand_data.dev_ready = nand_dev_ready;
+	gpio_direction_input(H3_NAND_RB_GPIO_PIN);
 
 	/* GPIO10 Func_MUX_CTRL reg bit 29:27, Configure V2 to mode1 as GPIO */
 	/* GPIO10 pullup/down register, Enable pullup on GPIO10 */
arch/arm/mach-omap1/board-perseus2.c +36 -13
index ca7df1e..dba0f7b 100644
@@ -30,7 +30,6 @@
 #include <mach/gpio.h>
 #include <plat/mux.h>
 #include <plat/fpga.h>
-#include <plat/nand.h>
 #include <plat/keypad.h>
 #include <plat/common.h>
 #include <plat/board.h>
@@ -134,8 +133,40 @@ static struct platform_device nor_device = {
 	.resource	= &nor_resource,
 };
 
-static struct omap_nand_platform_data nand_data = {
-	.options	= NAND_SAMSUNG_LP_OPTIONS,
+static void nand_cmd_ctl(struct mtd_info *mtd, int cmd,	unsigned int ctrl)
+{
+	struct nand_chip *this = mtd->priv;
+	unsigned long mask;
+
+	if (cmd == NAND_CMD_NONE)
+		return;
+
+	mask = (ctrl & NAND_CLE) ? 0x02 : 0;
+	if (ctrl & NAND_ALE)
+		mask |= 0x04;
+	writeb(cmd, (unsigned long)this->IO_ADDR_W | mask);
+}
+
+#define P2_NAND_RB_GPIO_PIN	62
+
+static int nand_dev_ready(struct mtd_info *mtd)
+{
+	return gpio_get_value(P2_NAND_RB_GPIO_PIN);
+}
+
+static const char *part_probes[] = { "cmdlinepart", NULL };
+
+static struct platform_nand_data nand_data = {
+	.chip	= {
+		.nr_chips		= 1,
+		.chip_offset		= 0,
+		.options		= NAND_SAMSUNG_LP_OPTIONS,
+		.part_probe_types	= part_probes,
+	},
+	.ctrl	= {
+		.cmd_ctrl	= nand_cmd_ctl,
+		.dev_ready	= nand_dev_ready,
+	},
 };
 
 static struct resource nand_resource = {
@@ -145,7 +176,7 @@ static struct resource nand_resource = {
 };
 
 static struct platform_device nand_device = {
-	.name		= "omapnand",
+	.name		= "gen_nand",
 	.id		= 0,
 	.dev		= {
 		.platform_data	= &nand_data,
@@ -201,13 +232,6 @@ static struct platform_device *devices[] __initdata = {
 	&lcd_device,
 };
 
-#define P2_NAND_RB_GPIO_PIN	62
-
-static int nand_dev_ready(struct omap_nand_platform_data *data)
-{
-	return gpio_get_value(P2_NAND_RB_GPIO_PIN);
-}
-
 static struct omap_lcd_config perseus2_lcd_config __initdata = {
 	.ctrl_name	= "internal",
 };
@@ -220,7 +244,7 @@ static void __init omap_perseus2_init(void)
 {
 	if (gpio_request(P2_NAND_RB_GPIO_PIN, "NAND ready") < 0)
 		BUG();
-	nand_data.dev_ready = nand_dev_ready;
+	gpio_direction_input(P2_NAND_RB_GPIO_PIN);
 
 	omap_cfg_reg(L3_1610_FLASH_CS2B_OE);
 	omap_cfg_reg(M8_1610_FLASH_CS2B_WE);
--

To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html

#2 lore raw
Quoted 6 lines · Tony Lindgren
Quoted 3 lines · Ladislav Michl

Since omapnand driver never find its way into mainline, switch to gen_nand instead. Following patch is compile tested only, but it is based on code I wrote for NetStar board and runtime tested it there.

Nice patch, and totally the way to go!

Well, after one week of silence... Anything else I could do to get it merged? Btw, these boards could probably use physmap-flash, so we could get rid of omap_nor as well.

Best regards,
ladis

#3 lore raw
Quoted 11 lines · Ladislav Michl
Quoted 6 lines · Tony Lindgren
Quoted 3 lines · Ladislav Michl

Since omapnand driver never find its way into mainline, switch to gen_nand instead. Following patch is compile tested only, but it is based on code I wrote for NetStar board and runtime tested it there.

Nice patch, and totally the way to go!

Well, after one week of silence... Anything else I could do to get it merged? Btw, these boards could probably use physmap-flash, so we could get rid of omap_nor as well.

No objections here. We haven't used f-sample boards since 2005, so there's no side-effects to cleanup that I'm worried about.

Brian

reviewer
#4 lore raw

PATCH 1/1 use gen_nand

In reply to Ladislav Michl

This patch has been applied to the linux-omap
by youw fwiendly patch wobot.

Branch in linux-omap: for-next-vol2

Initial commit ID (Likely to change): d6ebf3557861e5d023e11e027cd321b5e39f885b

PatchWorks
http://patchwork.kernel.org/patch/62142/

Git (Likely to change, and takes a while to get mirrored)
http://git.kernel.org/?p=linux/kernel/git/tmlind/linux-omap-2.6.git;a=commit;h=d6ebf3557861e5d023e11e027cd321b5e39f885b