Skip to contentSkip to conversation

Strange behaviour with initramfs and read-ahead settings

linux-lvm Michael Guntsche 2 participants 3 messages Nov 28, 2009

lore
Share & tools
lore
#0 lore raw

Hi list,

I am currently running the 2.6.32-rc8 kernel with lvm2 version 2.02.54-1 on debian unstable.
Since my root is on LVM as well I use an initramfs for booting. The setup I have consists of 5 disks in a RAID-5 with one PV on top of it. Now for my problem. The md device correctly sets the read-ahead to 4096. If I understand correctly lvm should get this value and set the read-ahead on the LVs accordingly. This is not working correctly for all my LVs.
Apart from the FIRST LV on the disk all the others show

Read ahead sectors auto
- currently set to 256

Since this did not seem to work I changed the RA with lvchange -r 4096 and rebooted. Swap now showed

Read ahead sectors 4096

while the other LVs still showed

Read ahead sectors 4096
- currently set to 256

lvs -o lv_read_ahead after boot

Rahead
2.00m
2.00m
2.00m
2.00m
2.00m

blockdev --getra showed 256 for each LV apart from the first one.

For testing purposes I took one LV (home) offline and back online again

lvchange -an;lvchange -ay

After that the readahead was set correctly to 4096. I am not sure what's happening here. I would understand a problem with getting the values automatically but right now they are saved in the metadata but are still set to 256.

I am glad for any help on this topic, in the mean-time I am using blockdev --setra to work around this problem.

Kind regards,
Michael Guntsche

#1 lore raw
Quoted 8 lines · Michael Guntsche

I am currently running the 2.6.32-rc8 kernel with lvm2 version 2.02.54-1 on debian unstable.
Since my root is on LVM as well I use an initramfs for booting. The setup I have consists of 5 disks in a RAID-5 with one PV on top of it. Now for my problem. The md device correctly sets the read-ahead to 4096. If I understand correctly lvm should get this value and set the read-ahead on the LVs accordingly. This is not working correctly for all my LVs.

Hi,

the logic is simple here
- if readahead is set to auto, it should inherit value from underlying device for all LVs on that PV
- if there is explicitly set value in metadata, it should always use that (you can switch back to auto by specifying -r auto)

(striped volumes calculate readahead differently, but it is not the case here)

There was similar issue - caused by not updated lvm in initrd (or with different lvm.conf there) - all volumes activated in initramdisk had different readahead value set - please check this.

Also Check default value of readahed in lvm.conf in activation section.

(See also https://bugzilla.redhat.com/show_bug.cgi?id=473273 )

If you still see that some volume is activated wrongly, please send debug output of lvchange -a y -vvvv <LV>, blockdev --getra <PV>

Quoted 8 lines

For testing purposes I took one LV (home) offline and back online again

lvchange -an;lvchange -ay

After that the readahead was set correctly to 4096. I am not sure what's happening here. I would understand a problem with getting the values automatically but right now they are saved in the metadata but are still set to 256.

Check which lvm activated it first - it seems that it uses old default or old version of lvm.

Milan
--
[email protected]

#2 lore raw
Quoted 5 lines · Milan Broz

the logic is simple here
- if readahead is set to auto, it should inherit value from underlying device for all LVs on that PV
- if there is explicitly set value in metadata, it should always use that (you can switch back to auto by specifying -r auto)

I updated the initramfs and all binaries and configs are the same. While debugging it further I noticed something. Since this is a server I connect via SSH. Immediately after reboot as soon as the ssh daemon started the read-ahead was ok (checked via blockdev). A few seconds later the numbers changed. Looking through my init scripts I saw that the mdadm --monitor daemon was started as well. I temporarily disabled it and checked after a reboot. The numbers did not change. I re-enabled the daemon but the numbers did not change either. I tried to reproduce the problems several times now but did not succeed. Of course this could be a red herring and the problem will re-appear but as it is now it seems LVM is doing the right thing and something else is changing the RA on my setup here. I debug this further the next time the problem shows up.

Please mind, in all this tests I only updated the initramfs only once and the problem was still there so I am ruling out a miss-configuration. It looks more likely that the number is changed under special circumstances.

Kind regards,
Michael